so that we return failure when we've failed and succeed when we succeed.
Otherwise, users always get a sn device :-(.
PR: 18431
Submitted by: <sanpei@sanpei.org> MIHIRA Yoshiro-san
Move the code that checks the card into _probe and out of _attach and
shuffle a couple of things around in attach.
Set ifp in the variable block - catches unused variables.
of some function names, dropping the ISA bits that were never used and
removing __P
We've renamed the _pccard_ stuff as nothing else probes or attaches.
In the next commit we will move some routines around and split out some of the
structure definitions to another file.
I've dropped the SYSCTL as I never got it working. APM is gone too as it
is broken.
Note, that the attr_read/write will be in both this and NEWCARD/NEWBUS so
I've moved the prototypes to the right place.
Add a few casts.
- Reload SCNTL3 after selection from host (C1010-33).
- Reload SCNTL4 prior to any DATA OUT phase (C1010-66).
- Use max SCSI offset 31 for ST but 62 for DT.
for transmit to the adapter, not when we receive a transmit interrupt
indicating that they were sent. This fix now allows tcpdump to produce
sane results by recording the timestamp at the point where the mbuf was
actually transmitted.
can use all of the s/g entries available on smaller cards. This is
necessary if we want to be able to handle a non-page-aligned 64k transfer
on 2.x and 3.x firmware.
Fix a missing splx() that may have left us at splbio() for longer than
desired.
Reduce shadowing of controller-supplied parameters a little.
<sys/bio.h>.
<sys/bio.h> is now a prerequisite for <sys/buf.h> but it shall
not be made a nested include according to bdes teachings on the
subject of nested includes.
Diskdrivers and similar stuff below specfs::strategy() should no
longer need to include <sys/buf.> unless they need caching of data.
Still a few bogus uses of struct buf to track down.
Repocopy by: peter
which seems to correspond better with what a busy plex needs. This
may also help us avoid race conditions when expanding the table which
may have been contributing to the random corruption, panics and hangs
we've been seeing in RAID-5 plexes, particularly with ata drives.
Eagerly-awaited-by: sos
Get counting volume I/Os right.
launch_requests: Be macho, throw away the safety net and walk the
tightrope with no splbio().
Add some comments explaining the smoke and mirrors.
Remove some redundant braces.
sdio: Set the state of an accessed but down subdisk correctly. This
appears to duplicate an earlier commit that I hadn't seen.
Get counting volume I/Os right.
Count buffer sizes correctly for architectures where ints are not 32 bits.
complete_rqe: Move decrementing active count until after call to
complete_raid5_write, thus possibly avoiding a race condition.
Suggested-by: dillon
Rename user bp to ubp to avoid confusion.
Tidy up comments.
a struct buf. Don't try to examine B_ASYNC, it is a layering violation
to do so. The only current user of this interface is vn(4) which, since
it emulates a disk interface, operates on struct bio already.
ioccom.h defines only implementation detail, and should therefore
only be included from the #include which defines the ioctl tags,
in other words: never include it from *.c
are two supported chips, the NetChip 1080 (only prototypes available)
and the EzLink cable. Any other cable should be supported however as they
are all very much alike (there is a difference between them wrt
performance).
It uses Netgraph.
This driver was mostly written by Doug Ambrisko and Julian Elischer and
I would like to thank Whistle for yet another contribution. And my
aplogies to them for me sitting on the driver for so long (2 months).
Also, many thanks to Reid Augustin from NetChip for providing me with a
prototype of their 1080 chip.
Be aware of the fact that this driver is very immature and has only been
tested very lightly. If someone feels like learning about Netgraph however
this is an excellent driver to start playing with.
coming later this week. Mitsuru IWASAKI provided a patch to -mobile which
I used to make sure I was doing the right thing but only a small part of
the actual patch was used.
that fails to proberly close the disk.
The problem seems to be that the HP burners sometimes return
ready when they actually are not, the solution is to not use
immediate mode on the closing commands. This is suboptimal
for real burners, in that they now hog the ATA bus for possibly
minutes, where its really not nessesary, *sigh*.
