revision 1.106
date: 2001/11/09 15:01:57; author: augustss; state: Exp; lines: +73 -57
Fix a bug in xfer abort processing when the HC executes ahead of what
the driver aborts.
Don't block RHSC interrupts.
revision 1.103
date: 2001/09/11 07:00:19; author: augustss; state: Exp; lines: +4 -1
Don't go top mode OPERATIONAL (before reset) on startup even
if BIOS claims to have initialized the controller.
hw.syscons.saver.keybonly: used to specify that only input is to
interrupt the screensaver. This allows one to run a chatty console
app but still have the screen blank out until a key is pressed.
There should probably also be an ioctl for this, we'll do that later.
hw.syscons.saver.blanktime: exports the screensaver timeout via sysctl.
Submitted by: Olivier Houchard <doginou@cognet.ci0.org>
interface that is compatible with the LUCENT or HERMES firmware.
Instead, it is like the various No Wires Necessary products that were
produced a while ago and then sold to intersil. It will require a
different driver altogether. Remove it from the list of supported
cards.
The 3CRWE777A apperas to be a re-badged SMC 2602W card, so the driver
appears to support it. Add it to the list.
Thanks to Todd Miller for loaning me the card during tonight's FRUUG
meeting for testing against CU's wireless infrastructure.
Grumble. I've seen better documented architectures out of Redmond.
Redo fabric evaluation to not use GET ALL NEXT (GA_NXT). Switches seem
to be trying to wriggle out of supporting this well. Instead, use
GID_FT to get a list of Port IDs and then use GPN_ID/GNN_ID to find the
port and node wwn. This should make working on fabrics a bit cleaner and
more stable.
This also caused some cleanup of SNS subcommand canonicalization so that
we can actually check for FS_ACC and FS_RJT, and if we get an FS_RJT,
print out the reason and explanation codes.
We'll keep the old GA_NXT method around if people want to uncomment a
controlling definition in ispvar.h.
This also had us clean up ISPASYNC_FABRICDEV to use a local lportdb argument
and to have the caller explicitly say that a device is at the end of the
fabric list.
MFC after: 1 week
time-of-day clocks, ported from NetBSD. The front-ends are expected
to be at least partly machine-dependent; the sparc64 EBus and SBus
ones will be commited to MD directories for now (in a subsequent commit).
wi.c 1.64: Table driven IDs (ichiro)
1.59: Don't use magic numbers (ichiro)
Also, added Sony, Lucent Embedded Ids and fix minor bugs for lucent
cards (and submit those changes back to ichiro-san)
Obtained from: NetBSD
most cases NULL is passed, but in some cases such as network driver locks
(which use the MTX_NETWORK_LOCK macro) and UMA zone locks, a name is used.
Tested on: i386, alpha, sparc64
o OpenBSD's wiconfig tells me that a value of '2' is for sony wireless
cards, 1 is for lucent (which we already knew) and '5' is for embedded
lucent cards.
o Move some RID definitions to if_wavelan_ieee.h and use NetBSD names
more often.
# more work is still needed in this area.
interrupts. This is a bit harder than it needs to be because there's
more than one way to generate link attentions, at least one of which
does not work on the BCM5700, but does on the 5701.
For the 5701, we can safely use the 'link changed' bit in the status
block, and we enable link change attentions in the mac event register.
For the 5700, we have to use MII interrupts, which require checking
the MAC status register rather than the status block. This requires
doing an extra register access on each interrupt which I'd prefer to
avoid, but them's the breaks. Testing with both a 3c996-T and 3c996B-T
shows that we do in fact detect the link going up and down properly
on cable insertions/disconnections.
Also, avoid twiddling the autopoll enable bit in the MI mode register
when doing a PHY read. I think this coupled with the other changes
will stop the interrupt storms Paul Saab has been harassing me about.
Manually setting the link to 100baseTX full duplex seems to work ok
for me. (I'm typing over the 3c996B-T right now.)
Lastly, teach the driver how to recognize a 3c996B-SX by checking
the hardware config word in the EEPROM in order to detect the media.
We attach 5701 fiber cards correctly now, but I haven't verified that
they send/receive packets yet since I don't have a second fiber
interface at home. (I know that fiber 5700 cards work, so I'm
keeping my fingers crossed.)
This driver was written by Myson and is made available
by their courtesy.
The 5.x version is not fully tested (I will be testing) but
the 4.x version has been tested by many.
I will commit it soon.
Myson have their own chip design based on the DEC 214xx family but
with several differences. Myson sells this chip to several
EOMs in teh Chinese area so there may be many noname brand cards
that respond to this driver. Myson will be supplying a list
of some of these.
1) Properly detect the Symbol based cards (The 3Com Airconnect and their
ilk) and only reset them *ONCE* ever. This appears to make them work,
but more testing is needed. The tests that would wedge up my machine
completely now appear to work, but I have not real access points
handy.
2) Report both the Station firmware and the Primary firmware on Prism
based cards. On Lucent based cards, only report the station firmware
since that's all it supports. On symbol cards, report the symbol
specific firmware name as its station firmware.
3) Better Prism 2.5 and 3 family names. We really need to go table
driven for this.
4) Workaround for bugs in Intersil's firmware is only needed for at most
0.8.2 and earlier, since 0.8.3 and later appear to work.
Obtained from: NetBSD
