o don't increment extracted tid, this was a vestige of IEEE80211_NONQOS_TID
being defined as 0 (w/ real tid's +1)
o handle 4-address frames (add IEEE80211_IS_DSTODS to check if an 802.11
header is DSTODS)
Submitted by: cbzimmer
Reviewed by: avatar
o replace DLT_IEEE802_11 support in net80211 with DLT_IEEE802_11_RADIO
and remove explicit bpf support from wireless drivers; drivers now
use ieee80211_radiotap_attach to setup shared data structures that
hold the radiotap header for each packet tx/rx
o remove rx timestamp from the rx path; it was used only by the tdma support
for debugging and was mostly useless due to it being 32-bits and mostly
unavailable
o track DLT_IEEE80211_RADIO bpf attachments and maintain per-vap and
per-com state when there are active taps
o track the number of monitor mode vaps
o use bpf tap and monitor mode vap state to decide when to collect radiotap
state and dispatch frames; drivers no longer explicitly directly check
bpf state or use bpf calls to tap frames
o handle radiotap state updates on channel change in net80211; drivers
should not do this (unless they bypass net80211 which is almost always
a mistake)
o update various drivers to be more consistent/correct in handling radiotap
o update ral to include TSF in radiotap'd frames
o add promisc mode callback to wi
Reviewed by: cbzimmer, rpaulo, thompsa
the net80211 layer has complete control over the handling of mgt frames
(in particular, the ac, tx rate, and retry count); this also allows us
to purge the M_LINK0 flag that was attached to mbufs to mark them as
needing encryption for shared key auth
o change ieee80211_send_setup to take a tid parameter so it can be used
to setup QoS frames
o correct BAR frame construction for AMPDU
o retransmit BAR frames until ACK'd or timeout (use tunables to
control behaviour, default is very aggressive)
o defer seq# update until BAR frame is ACK'd
o add BAR response handling callback for driver to interpose and
push new state to device or push pending aggregates
While here also:
o add backpointer to node in the per-tid tx aggregation data structure
o move ampdu tx state setup/teardown work to separate functions
o change ieee80211_parse_htcap and ieee80211_parse_htinfo to save only
internal state obtained from the ie's; no dynamic state such as
ni_chw is altered
o add ieee80211_ht_updateparams to parse ht cap+info ie's and update
dynamic node state
o change ieee80211_ht_node_init to not take an htcap ie that is parsed;
instead have the caller make a separate call as one caller wants to
parse the ie while another wants to parse both cap+info ie's and
update state so can better do this with ieee80211_ht_updateparams
These changes fix sta mode state handling where the node's channel
width was shifted to ht20/ht40 prematurely.
For receive:
o explicitly tag rx frames w/ M_AMPDU instead of passing frames through
the reorder processing according to the node having HT and the frame
being QoS data
o relax ieee80211_ampdu_reorder asserts to allow any frame to be passed
in, unsuitable frames are returned to the caller for normal processing;
this permits drivers that cannot inspect the PLCP to mark all data
frames as potential ampdu candidates with only a small penalty
o add M_AMPDU_MPDU to identify frames resubmitted from the reorder q
For transmit:
o tag aggregation candidates with M_AMPDU_MPDU
o fix the QoS ack policy set in ampdu subframes; we only support immediate
BA streams which should be marked for "normal ack" to get implicit block
ack behaviour; interestingly certain vendor parts BA'd frames with the
11e BA ack policy set
o do not assign a sequence # to aggregation candidates; this must be done
when frames are submitted for transmit (NB: this can/will be handled
better when aggregation is pulled up to net80211)
properly; was doing this only on a change in the protection mode
so the advertised protection mode in the beacon would oscillate.
Submitted by: Chris Zimmermann
o use txa_start to form the addba request and purge txa_seqstart
o fill txa_start before calling ic_addba_request to permit drivers
to override when they handle seq# generation (e.g. mwl)
Note this includes changes to all drivers and moves some device firmware
loading to use firmware(9) and a separate module (e.g. ral). Also there
no longer are separate wlan_scan* modules; this functionality is now
bundled into the wlan module.
Supported by: Hobnob and Marvell
Reviewed by: many
Obtained from: Atheros (some bits)
o add driver callback to handle notification of beacon changes;
this is required for devices that manage beacon frames themselves
(devices must override the default handler which does nothing)
o move beacon update-related flags from ieee80211com to the beacon
offsets storage (or handle however a driver wants)
o expand beacon offsets structure with members needed for 11h/dfs
and appie's
o change calling convention for ieee80211_beacon_alloc and
ieee80211_beacon_update
o add overlapping bss support for 11g; requires driver to pass
beacon frames from overlapping bss up to net80211 which is not
presently done by any driver
o move HT beacon contents update to a routine in the HT code area
Reviewed by: avatar, thompsa, sephe
Approved by: re (blanket wireless)
o update 11n definitions to D2.0 spec
o add IEEE80211_CAPINFO_SPECTRUM_MGMT for DFS support
o add CSA ie definition for DFS support
o purge some unused definitions
o correct 802.11 reason and status codes
o correct reason code returned when a sta tries to associate to an
ap operating with WPA/RSN but without a WPA/RSN ie
Reviewed by: thompsa, avatar
Approved by: re (blanket wireless)
o major overhaul of the way channels are handled: channels are now
fully enumerated and uniquely identify the operating characteristics;
these changes are visible to user applications which require changes
o make scanning support independent of the state machine to enable
background scanning and roaming
o move scanning support into loadable modules based on the operating
mode to enable different policies and reduce the memory footprint
on systems w/ constrained resources
o add background scanning in station mode (no support for adhoc/ibss
mode yet)
o significantly speedup sta mode scanning with a variety of techniques
o add roaming support when background scanning is supported; for now
we use a simple algorithm to trigger a roam: we threshold the rssi
and tx rate, if either drops too low we try to roam to a new ap
o add tx fragmentation support
o add first cut at 802.11n support: this code works with forthcoming
drivers but is incomplete; it's included now to establish a baseline
for other drivers to be developed and for user applications
o adjust max_linkhdr et. al. to reflect 802.11 requirements; this eliminates
prepending mbufs for traffic generated locally
o add support for Atheros protocol extensions; mainly the fast frames
encapsulation (note this can be used with any card that can tx+rx
large frames correctly)
o add sta support for ap's that beacon both WPA1+2 support
o change all data types from bsd-style to posix-style
o propagate noise floor data from drivers to net80211 and on to user apps
o correct various issues in the sta mode state machine related to handling
authentication and association failures
o enable the addition of sta mode power save support for drivers that need
net80211 support (not in this commit)
o remove old WI compatibility ioctls (wicontrol is officially dead)
o change the data structures returned for get sta info and get scan
results so future additions will not break user apps
o fixed tx rate is now maintained internally as an ieee rate and not an
index into the rate set; this needs to be extended to deal with
multi-mode operation
o add extended channel specifications to radiotap to enable 11n sniffing
Drivers:
o ath: add support for bg scanning, tx fragmentation, fast frames,
dynamic turbo (lightly tested), 11n (sniffing only and needs
new hal)
o awi: compile tested only
o ndis: lightly tested
o ipw: lightly tested
o iwi: add support for bg scanning (well tested but may have some
rough edges)
o ral, ural, rum: add suppoort for bg scanning, calibrate rssi data
o wi: lightly tested
This work is based on contributions by Atheros, kmacy, sephe, thompsa,
mlaier, kevlo, and others. Much of the scanning work was supported by
Atheros. The 11n work was supported by Marvell.
