o add ah_configPCIE and ah_disablePCIE for drivers to configure PCIE
power save operation (modeled after ath9k, may need changes)
o add private state flag to indicate if device is PCIE (replaces private
hack in 5212 code)
o add serdes programming ini bits for 5416 and later parts and setup
for each part (5416 and 9160 logic hand-crafted from existing routines);
5212 remains open-coded but is now hooked in via ah_configPCIE
o add PCIE workaround gunk
o add ar5416AttachPCIE for iodomatic code used by 5416 and later parts
o add output mux support
o gpio pin count is chip-dependent
o 9280 and 9285 do input handling different
o hookup gpio interrupts
o no need to save/restore soft led state around reset
o mark phy type to indicate 1/2 or 1/4-rate operation
o use phy type instead of channel attributes to identify 1/2 and 1/4-rate
operation
o general cleanup of code including move phy constants to ah_internal.h
Eventually this code should go away and we should use the net0211 equivalents.
guaranteed to initialize its two last arguments. Therefore, there is a
warning in the subsequent caller ar5416FillVpdTable(), which doesn't
initialize those arguments.
Change getLowerUpperIndex() to assign values to indexL and indexR even
in the case of assertion failure.
Submitted by: Pavel Roskin <proski@gnu.org>
o change tdma packet drop msg when ack required to ATH_DEBUG_TDMA
(ATH_DEBUG_XMIT is too noisy)
o add a debug msg for raw packet drop due to interface down/invalid
o add stats for these two cases
o explain how another drop case is handled
o remove HAL_CHANNEL; convert the hal to use net80211 channels; this
mostly involves mechanical changes to variable names and channel
attribute macros
o gut HAL_CHANNEL_PRIVATE as most of the contents are now redundant
with the net80211 channel available
o change api for ath_hal_init_channels: no more reglass id's, no more outdoor
indication (was a noop), anM contents
o add ath_hal_getchannels to have the hal construct a channel list without
altering runtime state; this is used to retrieve the calibration list for
the device in ath_getradiocaps
o add ath_hal_set_channels to take a channel list and regulatory data from
above and construct internal state to match (maps frequencies for 900MHz
cards, setup for CTL lookups, etc)
o compact the private channel table: we keep one private channel
per frequency instead of one per HAL_CHANNEL; this gives a big
space savings and potentially improves ani and calibration by
sharing state (to be seen; didn't see anything in testing); a new config
option AH_MAXCHAN controls the table size (default to 96 which
was chosen to be ~3x the largest expected size)
o shrink ani state and change to mirror private channel table (one entry per
frequency indexed by ic_devdata)
o move ani state flags to private channel state
o remove country codes; use net80211 definitions instead
o remove GSM regulatory support; it's no longer needed now that we
pass in channel lists from above
o consolidate ADHOC_NO_11A attribute with DISALLOW_ADHOC_11A
o simplify initial channel list construction based on the EEPROM contents;
we preserve country code support for now but may want to just fallback
to a WWR sku and dispatch the discovered country code up to user space
so the channel list can be constructed using the master regdomain tables
o defer to net80211 for max antenna gain
o eliminate sorting of internal channel table; now that we use ic_devdata
as an index, table lookups are O(1)
o remove internal copy of the country code; the public one is sufficient
o remove AH_SUPPORT_11D conditional compilation; we always support 11d
o remove ath_hal_ispublicsafetysku; not needed any more
o remove ath_hal_isgsmsku; no more GSM stuff
o move Conformance Test Limit (CTL) state from private channel to a lookup
using per-band pointers cached in the private state block
o remove regulatory class id support; was unused and belongs in net80211
o fix channel list construction to set IEEE80211_CHAN_NOADHOC,
IEEE80211_CHAN_NOHOSTAP, and IEEE80211_CHAN_4MSXMIT
o remove private channel flags CHANNEL_DFS and CHANNEL_4MS_LIMIT; these are
now set in the constructed net80211 channel
o store CHANNEL_NFCREQUIRED (Noise Floor Required) channel attribute in one
of the driver-private flag bits of the net80211 channel
o move 900MHz frequency mapping into the hal; the mapped frequency is stored
in the private channel and used throughout the hal (no more mapping in the
driver and/or net80211)
o remove ath_hal_mhz2ieee; it's no longer needed as net80211 does the
calculation and available in the net80211 channel
o change noise floor calibration logic to work with compacted private channel
table setup; this may require revisiting as we no longer can distinguish
channel attributes (e.g. 11b vs 11g vs turbo) but since the data is used
only to calculate status data we can live with it for now
o change ah_getChipPowerLimits internal method to operate on a single channel
instead of all channels in the private channel table
o add ath_hal_gethwchannel to map a net80211 channel to a h/w frequency
(always the same except for 900MHz channels)
o add HAL_EEBADREG and HAL_EEBADCC status codes to better identify regulatory
problems
o remove CTRY_DEBUG and CTRY_DEFAULT enum's; these come from net80211 now
o change ath_hal_getwirelessmodes to really return wireless modes supported
by the hardware (was previously applying regulatory constraints)
o return channel interference status with IEEE80211_CHANSTATE_CWINT (should
change to a callback so hal api's can take const pointers)
o remove some #define's no longer needed with the inclusion of
<net80211/_ieee80211.h>
Sponsored by: Carlson Wireless
down will cause a fault. Check the phy power state before possibly
reading from the bb, this can happen as ar5212Reset intentionally
calls ar5212GetRfgain before bringing the bb out of reset (but we
do it here and not in the caller to guard against other possible uses).
o add net80211 support for a tdma vap that is built on top of the
existing adhoc-demo support
o add tdma scheduling of frame transmission to the ath driver; it's
conceivable other devices might be capable of this too in which case
they can make use of the 802.11 protocol additions etc.
o add minor bits to user tools that need to know: ifconfig to setup and
configure, new statistics in athstats, and new debug mask bits
While the architecture can support >2 slots in a TDMA BSS the current
design is intended (and tested) for only 2 slots.
Sponsored by: Intel