Firmware tables require too much knowledge of system configuration,
and it's difficult to pass that information in general terms to a library.
The upcoming ACPI work exposed this - it will also livein bhyve.
Also, remove code specific to NetApp from the mptable name, and remove
the -n option from bhyve.
Reviewed by: neel
Obtained from: NetApp
- New memory region interface. An RB tree holds the regions,
with a last-found per-vCPU cache to deal with the common case
of repeated guest accesses to MMIO registers in the same page.
- Support memory-mapped BARs in PCI emulation.
mem.c/h - memory region interface
instruction_emul.c/h - remove old region interface.
Use gpa from EPT exit to avoid a tablewalk to
determine operand address. Determine operand size
and use when calling through to region handler.
fbsdrun.c - call into region interface on paging
exit. Distinguish between instruction emul error
and region not found
pci_emul.c/h - implement new BAR callback api.
Split BAR alloc routine into routines that
require/don't require the BAR phys address.
ioapic.c
pci_passthru.c
pci_virtio_block.c
pci_virtio_net.c
pci_uart.c - update to new BAR callback i/f
Reviewed by: neel
Obtained from: NetApp
AP needs to be activated by spinning up an execution context for it.
The local apic emulation is now completely done in the hypervisor and it will
detect writes to the ICR_LO register that try to bring up the AP. In response
to such writes it will return to userspace with an exit code of SPINUP_AP.
Reviewed by: grehan
the guest. Prior to the fix it was possible for such a bar to appear as a
32-bit bar as long as it was allocated from the region below 4GB.
This had the potential to confuse some drivers that were particular about
the size of the bars.
Obtained from: NetApp
These function number is specified by an optional [:<func>] after the slot
number: -s 1:0,virtio-net,tap0
Ditto for the mptable naming: -n 1:0,e0a
Obtained from: NetApp
or 32-bit signed integer.
Simplify the handling of indirect addressing with displacement by
unconditionally adding the 'instruction->disp' to the target address.
This is alright since 'instruction->disp' is non-zero only for the
addressing modes that specify a displacement.
Obtained from: NetApp
be activated as part of the slot config options.
The syntax is:
-s <slotnum>,uart[,stdio]
The stdio parameter instructs the code to perform i/o using
stdin/stdout. It can only be used for one instance.
To allow legacy i/o ports/irqs to be used, a new variant of
the slot command, -S, is introduced. When used to specify a
slot, the device will use legacy resources if it supports
them; otherwise it will be treated the same as the '-s' option.
Specifying the -S option with the uart will first use the 0x3f8/irq 4
config, and the second -S will use 0x2F8/irq 3.
Interrupt delivery is awaiting the arrival of the i/o apic code,
but this works fine in uart(4)'s polled mode.
This code was written by Cynthia Lu @ MIT while an intern at NetApp,
with further work from neel@ and grehan@.
Obtained from: NetApp
Includes instruction emulation for memory r/w access. This
opens the door for io-apic, local apic, hpet timer, and
legacy device emulation.
Submitted by: ryan dot berryhill at sandvine dot com
Reviewed by: grehan
Obtained from: Sandvine
run as a 1/2 CPU guest on an 8.1 bhyve host.
bhyve/inout.c
inout.h
fbsdrun.c
- Rather than exiting on accesses to unhandled i/o ports, emulate
hardware by returning -1 on reads and ignoring writes to unhandled
ports. Support the previous mode by allowing a 'strict' parameter
to be set from the command line.
The 8.1 guest kernel was vastly cut down from GENERIC and had no
ISA devices. Booting GENERIC exposes a massive amount of random
touching of i/o ports (hello syscons/vga/atkbdc).
bhyve/consport.c
dev/bvm/bvm_console.c
- implement a simplistic signature for the bvm console by returning
'bv' for an inw on the port. Also, set the priority of the console
to CN_REMOTE if the signature was returned. This works better in
an environment where multiple consoles are in the kernel (hello syscons)
bhyve/rtc.c
- return 0 for the access to RTC_EQUIPMENT (yes, you syscons)
amd64/vmm/x86.c
x86.h
- hide a bunch more CPUID leaf 1 bits from the guest to prevent
cpufreq drivers from probing.
The next step will be to move CPUID handling completely into
user-space. This will allow the full spectrum of changes from
presenting a lowest-common-denominator CPU type/feature set, to
exposing (almost) everything that the host can support.
Reviewed by: neel
Obtained from: NetApp
vmm.ko - kernel module for VT-x, VT-d and hypervisor control
bhyve - user-space sequencer and i/o emulation
vmmctl - dump of hypervisor register state
libvmm - front-end to vmm.ko chardev interface
bhyve was designed and implemented by Neel Natu.
Thanks to the following folk from NetApp who helped to make this available:
Joe CaraDonna
Peter Snyder
Jeff Heller
Sandeep Mann
Steve Miller
Brian Pawlowski
