Note: This also deprecates "NO" as a way to specify an empty list of
interfaces for gif_interfaces.
PR: conf/104884
Submitted by: nork
Harassed by: brd
Discussed with: brooks, dougb
modern dual-core systems as well.
- Parse the _CST packages for each cpu and track all the states individually,
on a per-cpu basis.
- Revert to generic FADT/P_BLK based Cx control if the _CST package
is not present on all cpus. In that case, the new driver will
still support per-cpu Cx state handling. The driver will determine the
highest Cx level that can be supported by all the cpus and configure the
available Cx state based on that.
- Fixed the case where multiple cpus in the system share the same
registers for Cx state handling. To do that, added a new flag
parameter to the acpi_PkgGas and acpi_bus_alloc_gas functions that
enable the caller to add the RF_SHAREABLE flag. This flag could also be
useful to other callers (acpi_throttle?) in the tree but this change is
not yet made.
- For Core Duo cpus, both cores seems to be taken out of C3 state when
any one of the cores need to transition out. This broke the short sleep
detection logic. It is disabled now if there is more than one cpu in
the system for now as it fixed it in my case. This quirk may need to
be re-enabled later differently.
- Added support to control cx_lowest on a per-cpu basis. There is still
a generic cx_lowest to enable changing cx_lowest for all cpus with a single
sysctl and for ease of use. Sample output for the new sysctl:
dev.cpu.0.cx_supported: C1/1 C2/1 C3/57
dev.cpu.0.cx_lowest: C3
dev.cpu.0.cx_usage: 0.00% 43.16% 56.83%
dev.cpu.1.cx_supported: C1/1 C2/1 C3/57
dev.cpu.1.cx_lowest: C3
dev.cpu.1.cx_usage: 0.00% 45.65% 54.34%
hw.acpi.cpu.cx_lowest: C3
This work was done by Stephane E. Potvin with some simple reworking by
myself. Thank you.
Submitted by: Stephane E. Potvin <sepotvin / videotron.ca>
MFC after: 2 weeks
in a previous commit to avoid namespace collisions, unfortunately I missed two
of them. This leads to the ip alias being incorrectly removed in some cases
when using the stop command.
Reported by: Philipp Wuensche <cryx-freebsd@h3q.com>
scripts, except for mdconfig* and jail. Such symbols are reserved
for the rc.subr internals. Most scripts can be fixed by just
declaring _foo symbols as local: few scripts actually need them to
be global.
Discussed with: dougb in freebsd-rc
A kernel with INET6 always has ::1 on lo0, so in the case of
ipv6_enable="NO" the lo0 can have ::1 with no link-local address.
This is a violation of the IPv6 specification. As a workaround for
this situation, fe80::1 is added in rc.d/auto_linklocal when lo0 has
no link-local address. This should not be harmful for IPv4-only users.
+ Use rc.subr(8) features properly.
+ Do the whole job of obliterating /tmp contents in find(1).
+ Leave lost+found and quota.{user,group} in /tmp only if root-owned.
+ Make the overall structure clearer by first removing the X dirs
(perhaps along with the rest of /tmp) and then re-creating them.
+ Use "find -exec rm -rf {} +" for efficiency: each rm instance gets
a chance to kill as much files in /tmp as ARG_MAX permits.
PR: bin/104044
Submitted by: Andrey Simonenko <see PR for email>
Hacked by: yar
MFC after: 1 month
chance to actually terminate the audit service and exit. Otherwise, on
an rc.d/auditd restart, the new audit daemon instance may try to start
auditing while the previous session is still running. Likewise, this
ensures a chance for auditd to terminate the audit trail at system
shutdown.
Perhaps more ideally, the script would wait synchronously for auditd to
exit rather than for an arbitrary but short period of time.
MFC after: 3 days
Obtained from: TrustedBSD Project
certain conditions. I haven't been able to find a better solution yet:
- Set a two read-only variables (${prefix} and ${etcdir}). This is
especially useful when using /etc/rc.d scripts with third-party
software installed from ports.
- Fix rc.d/sshd to work with openssh from ports using ${etcdir}
instead of hardcoded /etc.
- Reflect prefix/etcdir changes in rc.subr.8.
src/etc/rc.d/sshd: rev 1.9 -> 1.10
src/etc/rc.subr: rev 1.51 -> 1.52
src/share/man/man8/rc.subr.8: rev 1.11 -> 1.12
Approved by: cperciva (mentor)
despite the interface link status.
Add dhclient_flags_iface and background_dhclient_iface rc.conf options.
(where iface is a specific interface). These can be used to give
interface specific flags to dhclient.
Reviewed by: brooks@
and replace it with a new ntpdate_config variable.
- Document it in defaults/rc.conf and rc.conf.5.
- Document ntpdate_hosts in defaults/rc.conf.
Requested by: Chris Timmons <cwt@networks.cwu.edu>
Approved by: cperciva (mentor, implicit)
MFC after: 1 week
not be mounted unless the -l flag was specified.
Add an rc script, mountlate, which basically runs 'mount -a -l'. It runs
after DAEMON but before LOGIN.
This is useful for things like loopback mounts, because mountcritremote
runs before mountd / nfsd (since /usr might be a remote file system), so
an attempt to mount a loopback network file system in mountcritremote will
fail.
Also add a progress message to mountcritlocal, for the sake of symmetry
with similar messages in mountcritremote and mountlate.
Reviewed by: freebsd-rc
MFC after: 3 weeks
expect to see quite a few files appearing in libdata/ldconfig directories.
This change avoids the screen to be filled with the names of those ldconfig
files and replace them by the actual non-default directories they contain.
Most of them will be ${PREFIX}/lib so, 'sort -u' will help reducing the
output.
Approved by: cperciva (implicit)
MFC after: 1 week
automaticly add it to an Ethernet bridge. This is intended for applications
such as qemu, vmware, openvpn, ... which open tap interfaces and need them
bridged with the hosts network adapter, the user can set up a glob for
interfaces to be automatically added (eg tap*).
notification so all interfaces including pseudo are reported. When netif
creates the clones at startup devctl_disable has not been turned off yet so the
interfaces will not be initialised twice, enforce this by adding an explicit
order between rc.d/netif and rc.d/devd.
This change allows actions to taken in userland when an interface is cloned
and the pseudo interface will be automatically configured if a ifconfig_<int>=""
line exists in rc.conf.
Reviewed by: brooks
No objections on: net
