mount point crossings correctly. It was testing the wrong flag.
Also, try harder to make sure that the fsid is different than
the one assigned to the client mount point, by hashing the
server's fsid (just to create a different value deterministically)
when it is the same.
MFC after: 2 weeks
details of each rman header, but not the contents of all rman structures
in the system. This is especially useful on platforms where some rmans
have many thousands of entries in rmans, making scrolling through the
output of "show all rman" impractical. Individual rmans can then be viewed
including their contents with "show rman 0xaddr" as usual.
Reviewed by: jhb
- make SATA SIMs announce capabilities to handle SDB with Notification bit;
- make PMP driver honor this SIMs capability;
- make SATA XPT to negotiate and enable this feature for ATAPI devices.
This feature allows supporting SATA ATAPI devices to inform system about
some events happened, that may require attention. In my case this allows
LG GH22LS50 SATA DVR-RW drive to report tray open/close events. Events
reported to CAM in form of AC_SCSI_AEN async. Further they could be used
as a hints for checking device status and reporting media change to upper
layers, for example, via spoiling mechanism of GEOM.
diversity.
This is bit dirty and likely should be revised at a later date,
with an eye to unifying/tidying up the whole diversity setup
and allowing developers to do "tricky stuff" as they desire.
For now, this works.
* add a new method, specifically for doing per-RX packet
antenna diversity
* set that HAL method only if it's Kite and a Kite chip that
does diversity.
* add a diversity flag to the HAL debugging section
* add a check to make sure the kite diversity code doesn't run
on boards that don't require it, as not all Kite chips will
implement it.
* add some debug statements when the diversity code makes
changes to the antenna diversity/combining setup.
controller port readiness (that should set just after PHY ready signal),
reduce wait time from 10s to 1s before trying more aggressive reset method.
This should improve system responsibility in some failure conditions.
Note: this HAL currently only supports the AR9285.
From Linux ath9k:
The problem is that when the attenuation is increased,
the rate will start to drop from MCS7 -> MCS6, and finally
will see MCS1 -> CCK_11Mbps. When the rate is changed b/w
CCK and OFDM, it will use register desired_scale to calculate
how much tx gain need to change.
The output power with the same tx gain for CCK and OFDM modulated
signals are different. This difference is constant for AR9280
but not AR9285/AR9271. It has different PA architecture
a constant. So it should be calibrated against this PA
characteristic.
The driver has to read the calibrated values from EEPROM and set
the tx power registers accordingly.
the username-for-accounting field (P), not the username-for-headerpage (L).
These are usually the same value, except that control files do not have
the username-for-headerpage field if the user has requested no header page.
- Also rename the cji_username field to cji_headruser, to make it clear that
the value should only be used for the header page. (aka banner page)
MFC after: 3 weeks
not believe that these leaks had a practical impact,
since the situations in which they would have occurred
would have been extremely rare.
MFC after: 2 weeks
MPERF MSRs are available. It was disabled in r216443. Remove the earlier
hack to subtract 0.5% from the calibrated frequency as DELAY(9) is little
bit more reliable now.
prefixes (Ki, Mi, Gi...) for humanize_number(3).
Note that applications has to pass HN_IEC_PREFIXES to use this
feature for backward compatibility reasons.
Reviewed by: arundel
MFC after: 2 weeks
Instead of spinning in a tight loop for up to 15 seconds, polling for device
readiness while it spins up, return reset completion just after PHY reports
"connect well" or 100ms connection timeout. If device was found, use callout
for checking device readiness with 100ms period up to full 31 second timeout.
This fixes system freeze for 5-10 seconds on drives hot plug-in.
embedded flash stores.
Some devices - notably those with uboot - don't have an
explicit partition table (eg like Redboot's FIS.)
geom_map thus provides an easy way to export the hard-coded
flash layout as geom providers for use by filesystems and
other tools.
It also includes a "search" function which allows for
dynamic creation of partition layouts where the device only
has a single hard-coded partition. For example, if
there is a "kernel+rootfs" partition, a single image can
be created which appends the rootfs after the kernel with
an appropriate search string. geom_map can be told to
search for said search string and create a partition
beginning after it.
Submitted by: Aleksandr Rybalko <ray@dlink.ua>
bus driver at detach, hence ehci_detach() does exactly this since r199718.
Submitted by: Luiz Otavio O Souza
MFC after: 7 days
Approved by: thompsa (mentor)
this happens just before the build is started (within the same second)
CHECK_TIME actually triggers thinking param.h is in the future (see f_Xtime,
c_Xtime logi in find(1) sources for the details in !F_EXACTTIME case).
Using the -mtime -0s (seconds, rather than no unit) avoids this 1s race.
Submitted by: ed (2009-05-03)
Reviewed by: cperciva (2009-05-03), emaste
Tested by: bz (for almost two years)
MFC after: 4 days
of NFSv2 getting an error return from VOP_MKNOD(). Without this
patch, the server file system remains busy after an NFSv2
VOP_MKNOD() fails.
MFC after: 2 weeks
