their svr4_stat64 structures with old dev_t values instead of udev_t's.
Panic was caused when major() and minor() were called with args which
weren't pointers. The panic was probably introduced in rev 1.51 of
kern_conf.c
vnodes are locked and never unlocked, which leads to processes starting
to wedge up after doing a mount -o nfsv3,tcp,rdirplus foo:/fs /fs; ls /fs.
The second is that sometimes cnp is accessed without having been
properly initialized: cnp->cn_nameptr points to an earlier name while
"len" contains the length of a current name of different size. This
leads to an attempt to dereference *(cn->cn_nameptr + len) which will
sometimes cause a page fault and a panic.
With these two fixes, client side readdirplus works correctly with
FreeBSD, IRIX 6.5.4 and Solaris 2.5.1 and 2.6 servers.
Submitted by: Matthew Dillon <dillon@backplane.com>
being incremented by 4 bytes too few each time through the loop, which
allows more data into the mbuf chain that we really want. In the worst
case, when we're using 32K read/write sizes with a TCP client, this causes
readdirplus replies to sometimes exceed NFS_MAXPACKET which leads to a
panic. This problem cropped up for me using an IRIX 6.5.4 NFSv3 TCP client
with 32K read/write sizes, however supposedly it can be triggered by
WinNT NFS servers too. In theory, it can probably be triggered by any
NFS v3 implementation using TCP as long as it's using the maxiumum block
size.
Reviewed by: Matthew Dillon <dillon@backplane.com>
space of PCI devices that don't exist cause PCI master & target aborts
rather than returning ~0 or giving a machine check. Bring in some code
from NetBSD to handle this properly.
obtained from: NetBSD
reviewed by: dfr
- Add support for calling 32-bit code in other segments
- Add support for calling 16-bit protected mode code
Update APM to use this facility.
Submitted by: jlemon
- device_print_child() either lets the BUS_PRINT_CHILD
method produce the entire device announcement message or
it prints "foo0: not found\n"
Alter sys/kern/subr_bus.c:bus_generic_print_child() to take on
the previous behavior of device_print_child() (printing the
"foo0: <FooDevice 1.1>" bit of the announce message.)
Provide bus_print_child_header() and bus_print_child_footer()
to actually print the output for bus_generic_print_child().
These functions should be used whenever possible (unless you can
just use bus_generic_print_child())
The BUS_PRINT_CHILD method now returns int instead of void.
Modify everything else that defines or uses a BUS_PRINT_CHILD
method to comply with the above changes.
- Devices are 'on' a bus, not 'at' it.
- If a custom BUS_PRINT_CHILD method does the same thing
as bus_generic_print_child(), use bus_generic_print_child()
- Use device_get_nameunit() instead of both
device_get_name() and device_get_unit()
- All BUS_PRINT_CHILD methods return the number of
characters output.
Reviewed by: dfr, peter
result of a joined effort with parts contributed by Doug Rabson, Warner
Losh and Stefan Esser (hope I did not forget anybody). Part of the sources
is obtained from NetBSD with modifications.
This code is work in progress:
As of the time of the initial import, a loader.exe executable is built,
which can be loaded on an Alpha with NT only firmware, but no attempt is
made to switch to OSF PAL code as required to start an actual kernel.
active or not. The only sane thing we can do here is assume that if
APM is supported it might be active at some point, and bail.
In reality, even this isn't good enough; regardless of whether we support
APM or not, the system may well futz with the CPU's clock speed and throw
the TSC off. We need to stop using it for timekeeping except under
controlled circumstances. Curse the lack of a dependable high-resolution
timer.
equivalent to SYS_RES_MEMORY for x86 but for alpha, the rman_get_virtual()
address of the resource is initialised to point into either dense-mapped
or bwx-mapped space respectively, allowing direct memory pointers to be
used to device memory.
Reviewed by: Andrew Gallatin <gallatin@cs.duke.edu>
This function is called for each device for which no driver
was found.
Output is similar to the eisa_probe_nomatch() function but with the
added benefit of displaying the assigned IRQ (since PCI gives us
this information up front.)
Output is like so:
pci0: unknown card CPQ0508 (vendor=0x0e11, dev=0x0508) at 11.0 irq 9
pci0: unknown card DFZ0508 (vendor=0x10da, dev=0x0508) at 11.0 irq 9
pci0: unknown card DBL0508 (vendor=0x104c, dev=0x0508) at 11.0 irq 9
pci0: unknown card DDM0011 (vendor=0x108d, dev=0x0011) at 11.0 irq 9
I'm not happy with the 3 lines of macro cruft that got added but
I consider it a temporary annoyance as those bits will be moved to
some place where PCI, EISA and ISAPNP code will be able to use them.
(Not surprisingly, this message is longer than the code in question.)
Reviewed by: peter, dfr
a PCI memory mapped region, rman_get_bushandle() returns what happens
to be a kernel virtual address pointing to the base of the PCI shared
memory window. However this is not the behavior on all platforms:
the only thing you should do with the bushandle is pass it to the
bus_spare_read()/bus_space_write() routines. If you actually do want
the kernel virtual address of the base of the PCI memory window, you
need to use rman_get_virtual().
The problem is that at the moment, rman_get_virtual() returns a physical
address, which is bad. In order to get the kernel virtual address we
need, we have to play with it a little.
Presumeably this behavior will be changed, but in the meantime the
Tigon driver won't work. So for the moment, I'm adding a kludge to
make things happy on the alpha: the correct kernel virtual address
is calculated from the value returned by rman_get_virtual(). This
should be removed once rman_get_virtual() starts doing the right
thing.
This should make the Tigon actuall work on the alpha now.
