Changes to pmap.c for lapic_t lapic && ioapic_t ioapic pointers,
currently equal to apic_base && io_apic_base, will stand alone with the
private page mapping.
apic.h has defines like:
#define lapic__id lapic->id
Once private pages and "known virtual addr" mapping of the APICs is
ready all 'lapic__XXX' will be changed to 'lapic.XXX', and the defines
will be removed.
Changes to smp.h for lapic_t lapic && ioapic_t ioapic pointers,
currently equal to apic_base && io_apic_base, will stand alone with the
private page mapping.
Return failure, if the enable bit corresponding to the map type has not
been set in the command register. This feature was requested by Justin
Gibbs, who pointed out that some early PCI to PCI bridges do not correctly
support memory windows (I assume because of the risk of deadlocks that
have been taken care of in the PCI 2.2 spec) and that some BIOS clears
the memory address decode enable bit in the command register of the PCI
device, if it finds them behind such a bridge.
1) Stop at the first map register that contains a zero value.
2) When testing for the map size work up from low values, since
this works around a bug in some BusLogic SCSI card, which has
the 16 upper port base address bits hardwired to zero.
The config register dump printed in the bootverbose case has
been slightly rearranged.
Adjust the data port address by adding the two low order bits of
the register number. The address port takes only a word address
(i.e. ignores the two low order bits written to it).
mode 1. Omission of this bit makes all config register accesses fail in
on recent chip sets ...
(The problem was reported and debug output provided by: Steve Passe)
- vector.s <- stub called by i386/exception.s
- icu_vector.s <- UP
- apic_vector.s <- SMP
Split icu.s into UP and SMP specific files:
- ipl.s <- stub called by i386/exception.s (formerly icu.s)
- icu_ipl.s <- UP
- apic_ipl.s <- SMP
This was done in preparation for massive changes to the SMP INTerrupt
mechanisms. More fine tuning, such as merging ipl.s into exception.s,
may be appropriate.
reality. There will be a new call interface, but for now the file
pci_compat.c (which is to be deleted, after all drivers are converted)
provides an emulation of the old PCI bus driver functions. The only
change that might be visible to drivers is, that the type pcici_t
(which had been meant to be just a handle, whose exact definition
should not be relied on), has been converted into a pcicfgregs* .
The Tekram AMD SCSI driver bogusly relied on the definition of pcici_t
and has been converted to just call the PCI drivers functions to access
configuration space register, instead of inventing its own ...
This code is by no means complete, but assumed to be fully operational,
and brings the official code base more in line with my development code.
A new generic device descriptor data type has to be agreed on. The PCI
code will then use that data type to provide new functionality:
1) userconfig support
2) "wired" PCI devices
3) conflicts checking against ISA/EISA
4) maps will depend on the command register enable bits
5) PCI to Anything bridges can be defined as devices,
and are probed like any "standard" PCI device.
The following features are currently missing, but will be added back,
soon:
1) unknown device probe message
2) suppression of "mirrored" devices caused by ancient, broken chip-sets
This code relies on generic shared interrupt support just commited to
kern_intr.c (plus the modifications of isa.c and isa_device.h).
be (eventually) architecture independent. It provides an emulation
of the ISA interrupt registration function register_intr(), but that
function does no longer manipulated the interrupt controller and
interrupt descriptor table, but calls the architecture dependent
function setup_icu() for that purpose.
After the ISA/EISA bus code has been modified to directly call the new
interrupt registartion functions (intr_create() and intr_connect()),
the emulation of register_intr() should be dropped.
The C level interrupt handler function should take a (void*) argument,
and the function pointer type (inthand2_t) should defined in some other
place than isa_device.h.
This commit is a pre-requisite for the removal of the PCI specific shared
interrupt code.
Reviewed by: dfr,bde
be (eventually) architecture independent. It provides an emulation
of the ISA interrupt registration function register_intr(), but that
function does no longer manipulated the interrupt controller and
interrupt descriptor table, but calls the architecture dependent
function setup_icu() for that purpose.
After theISA/EISA bus code has been modified to directly call the new
interrupt registartion functions (intr_create() and intr_connect()),
the emulation of register_intr() should be dropped.
The C level interrupt handler function should take a (void*) argument,
and the function pointer type (inthand2_t) should defined in some other
place than isa_device.h.
This commit is a pre-requisite for the removal of the PCI specific shared
interrupt code.
Reviewed by: dfr,bde
This is now the default, it delays most of the MP startup to the function
machdep.c:cpu_startup(). It should be possible to move the 2 functions
found there (mp_start() & mp_announce()) even further down the path once
we know exactly where that should be...
Help from: Peter Wemm <peter@spinner.dialix.com.au>
