if_start routines cannot currently be entered without Giant. When
the kernel is running with debug.mpsafenet != 0, this will defer
if_start execution to a task queue thread holding Giant, which may
introduce additional latency, but avoid incorrect execution.
Suggested by: dfr
skip blocks that are too big by a factor of two or greater. This
avoids some cases of extremely inefficient memory use that can occur
when large (e.g. 64k) blocks on the free list get used when allocating
a 4k chunk of 64-byte fragments. Because fragments have their own
free list, the 60k difference got lost forever every time.
system BIOS to disable legacy device emulation as per the "EHCI
Extended Capability: Pre-OS to OS Handoff Synchronisation" section
of the EHCI spec. BIOSes that implement legacy emulation using SMIs
are supposed to disable the emulation when this procedure is performed.
to be particularly correct or optimal, but it seems to be enough
to allow the attachment of USB2 hubs and USB2 devices connected via
USB2 hubs. None of the split transaction support is implemented in
our USB stack, so USB1 peripherals will definitely not work when
connected via USB2 hubs.
Improve child_detached a little and make it conform better to
style(9). Also, improve comment about what we'll be doing in the
future about driver_added. Soon it will be possible to kldload usb
drivers and have them attach w/o a need to disconnect/reconnect them.
usbdi.c rev. 1.104, author: mycroft
ugen_isoc_rintr() may recycle the xfer immediately. Therefore, we
avoid touching the xfer after calling the callback in
usb_transfer_complete(). From PR 25960.
future:
rename ttyopen() -> tty_open() and ttyclose() -> tty_close().
We need the ttyopen() and ttyclose() for the new generic cdevsw
functions for tty devices in order to have consistent naming.
rev. 1.67, author: mycroft
Fix a byte order error.
rev. 1.68, author: mycroft
Adjust some silliness that was causing us to do extra work for
"frame list rollover" interrupts, which we pretty much ignore.
Obtained from: NetBSD
rev. 1.68, author: mycroft
Ignore a port error that happens to come in at the same time as a
connect status change. Some root hubs seem to report both.
Obtained from: NetBSD
bus interfaces. These interfaces use the FTDI chipset with different
Vendor and Product IDs.
Add two additional baud rate enumerations. The vehicle bus interfaces
use a baud rate of 2000000. Also add 3000000 as it is the other FTDI
baud divisor special case.
I've commited a slightly different patch from that provided in the PR as
I changed the matching code a bit yesterday.
Submitted by: Mike Durian <durian at shadetreesoftware.com>
PR: kern/67357
operations when the refcount doesn't protect the opens and closes. Fix
this, and don't actually let a time out happen: now ugen(4) devices do
not get freed out from under the programs with them open.
uhid.c (1.61), author: jdolecek
add support for USB_GET_DEVICEINFO and USB_GET_STRING_DESC ioctls,
with same meaning as for ugen(4)
usbdi_util.h (1.29), usb_quirks.c (1.50), uhid.c (1.62),
ugen.c (1.68), usb_subr.c (1.114) author: mycroft
Yes, some devices return incorrect lengths in their string
descriptors. Rather than losing, do what Windows does: just
request the maximum size, and allow a shorter response. Obsoletes
the need for UQ_NO_STRINGS, and therefore these "quirks" are removed.
usb_subr.c (1.116), author: mycroft
In the "seemed like a good idea until I found the fatal flaw"
department... Attempting to read a maximum-size string descriptor
causes my kue device to go completely apeshit. So, go back to the
original method, but allow the device to return a shorter string than
it claimed.
Obtained from: NetBSD
copies.
No current line disciplines have a dynamically changing hotchar, and
expecting to receive anything sensible during a change in ldisc is
insane so no locking of the hotchar field is necessary.
ohci.c (1.147), author: mycroft
Failure to properly mask off UE_DIR_IN from the endpoint address
was causing OHCI_ED_FORMAT_ISO and EHCI_QH_HRECL to get set
spuriously, causing rather interesting lossage.
Suddenly I get MUCH better performance with ehci...
ohci.c (1.148), author: mycroft
Adjust a couple of comments to make it clear WTF is going on.
Obtained from: NetBSD
ehci.c (1.55), ehcireg.h (1.16); author: mycroft
Set the data toggle correctly, and use EHCI_QTD_DTC. This fixes
problems with my ALi-based drive enclosure (it works now, rather
than failing to attach). Also seems to work with a GL811-based
enclosure and an ASUS enclosure with a CD-RW, on both Intel and
NEC controllers.
Note: The ALi enclosure is currently very SLOW, due to some issue
with taking too long to notice that the QTD is complete. This
requires more investigation.
ehci.c (1.56); author: mycroft
Failure to properly mask off UE_DIR_IN from the endpoint address
was causing OHCI_ED_FORMAT_ISO and EHCI_QH_HRECL to get set
spuriously, causing rather interesting lossage.
Suddenly I get MUCH better performance with ehci...
ehci.c (1.58); author: mycroft
Fix a stupid bug in ehci_check_intr() that caused use to try to
complete a transaction that was still running. Now ehci can
handle multiple devices being active at once.
ehci.c (1.59); author: enami
As the ehci_idone() now uses the variable `epipe'
unconditionally, always declare it (in other words, make this
file compile w/o EHCI_DEBUG).
ehci.c (1.60); author: mycroft
Remove comment about the data toggle being borked.
ehci.c (1.61); author: mycroft
Update comment.
ehci.c (1.62); author: mycroft
Adjust a couple of comments to make it clear WTF is going on.
ehci.c (1.63); author: mycroft
Fix an error in a debug printf().
ehci.c (1.64), ehcireg.h (1.17); author: mycroft
Further cleanup of toggle handling. Now that we use EHCI_QH_DTC,
we don't need to fiddle with the TOGGLE bit in the overlay
descriptor, so minimize how much we fuss with it.
Obtained from: NetBSD
Thanks to Sam for importing tags in a way that allowed this to be done.
Submitted by: Gleb Smirnoff <glebius@cell.sick.ru>
Also allow the sr and ar drivers to create netgraph versions of their modules.
Document the change to the ksocket node.
Several changes:
* Implement read for ulpt.
* If the device is not opened for reading, occasionally drain any
data the printer might have (but don't hammer the printer with reads).
* Lower the buffer size to one page.
The driver seems to work with more printers now.
Obtained from: NetBSD
as otherwise the junk it contains may cause uhub_explore to give
up without ever trying to restart the port. This fixes the following
errors I was seeing with a VIA UHCI controller:
uhub0: port error, restarting port 1
uhub0: port error, giving up port 1
