* Re-do the structure size/component math to make sure the struct matches
the expected size
* Just to be clear that we care about bitmask ordering, revert my previous
change and instead define that macro if we're on big-endian.
It turns out that the V4K eeprom definitions (used by the AR9285 and
its derivatives) is wrong. These values are at least causing issues
on my AR2427.
With this fix (and initvals in a subsequent commit), the AR2427 behaves
a lot better.
Note - there's still significant drift between the ath9k v4k eeprom
init code (again, used by AR9285 and derivatives) and what's in this
tree. That needs to be investigated and resolved.
prevent sending data when CTS is de-asserted.
In uart_tty_intr(), call uart_tty_outwakeup() when the CTS signal
changed, knowing that uart_tty_outwakeup() will do the right
thing for flow control. This avoids redundant conditionals.
PR: kern/148644
Submitted by: John Wehle <john@feith.com>
MFC after: 3 days
via AHCI-like memory resource at BAR(5). Use it if BIOS was so kind to
allocate memory for that BAR. This allows hot-plug support and connection
speed reporting.
MFC after: 2 weeks
controllers. Experimentation with RTL8102E, RTL8103E and RTL8105E
showed dramatic decrement of TX completion interrupts under high TX
load(e.g. from 147k interrupts/second to 10k interrupts/second)
With this change, TX interrupt moderation is applied to all
controllers except RTL8139C+.
The linux ath9k driver and (from what I've been told) the atheros reference
driver does this; it then leaves discarding 11n frames to the 802.11 layer.
Whilst I'm here, merge in a fix from ath9k which maintains a turbo register
setting when enabling the 11n register; and remove an un-needed (duplicate)
flag setting.
The v1 and v3 interfaces returned the whole EEPROM but the v14/v4k
interfaces just returned the base header. There's extra information
outside of that which would also be nice to get access to.
The rxmonitor hook is called on each received packet. This can get very,
very busy as the tx/rx/chanbusy registers are thus read each time a packet
is received.
Instead, shuffle out the true per-packet processing which is needed and move
the rest of the ANI processing into a periodic event which runs every 100ms
by default.
value. While I'm here enable all clocks before initializing
controller. This change should fix lockup issue seen on AR8152
v1.1 PCIe Fast Ethernet controller.
PR: kern/154076
MFC after: 3 days
This is apparently an AR9285 with the 802.11n specific bits disabled.
This code is completely untested; I'm doing this in response to users
who wish to test the functionality out. It's likely as buggy as the
AR9285 support is in FreeBSD at the moment.
sys/dev/ath/ath_hal/ar5416/ is getting very crowded and further
commits will make it even more crowded. Now is a good time to
shuffle these files out before any more extensive work is done
on them.
Create an ar9003 directory whilst I'm here; ar9003 specific
chipset code will eventually live there.
with these ADC DC Gain/Offset calibrations.
The whole idea is to calibrate a pair of ADCs to compensate for any
differences between them.
The AR5416 returns lots of garbage, so there's no need to do the
calibration there.
The AR9160 returns 0 for secondary ADCs when calibrating 2.4ghz 20mhz
modes. It returns valid data for the secondary ADCs when calibrating
2.4ghz HT/40 and any 5ghz mode.
This removes the chipset-dependent TX DMA completion descriptor groveling.
It should now be (more) portable to other, later atheros chipsets when the
time comes.
The AR9100 at least doesn't have an external serial EEPROM
attached to the MAC; it instead stores the calibration data
in the normal system flash.
I believe earlier parts can do something similar but I haven't
experienced it first-hand.
This commit introduces an eepromdata pointer into the API but
doesn't at all commit to using it. A future commit will
include the glue needed to allow the AR9100 support code
to use this data pointer as the EEPROM.
the completion schedule from the hardware and returns AH_TRUE if
the hardware supports multi-rate retries (AR5212 and above); and
returns AH_FALSE if the hardware doesn't support multi-rate retries.
The sample rate module directly reads the TX completion descriptor
and extracts the TX schedule information from that. It will be
updated in a future commit to instead use this method to determine
the completion schedule.
Since we now have the source code, there's no reason to hide the diag codes
from other areas.
They live in the HAL as they form part of the HAL API and should still be treate
as "potentially flexible; don't publish as a public API." But since they're
already used as a public API (see follow-up commit), we may as well use
them in place of magic constants.
CRITICAL FIX - with stats changes the older 82598 will panic
and trash the stack on driver load, FCOE registers ONLY exist
in 82599 and must not be read otherwise.
kern/153951 - to correct incorrect media type on adapters
with pluggable modules I have eliminated the old static
table in favor of a new dynamic shared code routine. This
also has the benefit of detecting changes when a different
module is inserted.
Performance/enhancement to the Flow Director code from my
linux coworker (the developer of the code).
Fixes from Michael Tuexen - a data corruption problem on the
82599 (CRITICAL), fix so the buf size correctly adjusts as
the cluster changes, and max descriptors are set properly.
Also added 16K clusters for those REALLY big jumbos :)
In the RX path, the RX LOCK was not being released, and this
causes LOR problems. Add the code that igb already has.
Sync with in house shared code, this was necessary for the
Flow Director fix.
MFC in 2 days
reading. (This was already done for writing to a sysctl). This
requires all SYSCTL setups to specify a type. Most of them are now
checked at compile-time.
Remove SYSCTL_*X* sysctl additions as the print being in hex should be
controlled by the -x flag to sysctl(8).
Succested by: bde
for this sensor. Instead of leaving this location empty we use here
the default name 'sensor'.
Submitted by: Justin Hibbits <chmeeedalf at gmail dot com>
Approved by: nwhitehorn (mentor)
DP8381[56] and SiS 900/7016 controllers. After r212119, sis(4) no
longer reinitializes controller if ALLMULTI/PROMISC was changed.
However, RX filter handling code assumed some bits of the RX filter
is programmed by driver initialization. This caused ALLMULTI/PROMISC
configuration is ignored under certain conditions.
Fix that issue by reprogramming all bits of RX filter register.
While I'm here follow recommended RX filter programming steps
recommended by National DP8381[56] data sheet(RX filter should be
is disabled before programming).
Reported by: Paul Schenkeveld < freebsd () psconsult dot nl >
Tested by: Paul Schenkeveld < freebsd () psconsult dot nl >
MFC after: 3 days
- Remove extra unlock from end of ale_start_locked().
- Expand scope of locking in interrupt handler.
- Move ether_ifdetach() earlier and retire now-unneeded DETACH flag.
Tested by: Aryeh Friedman
Reviewed by: yongari (earlier version)
