- Bump link state when stopping or starting the interface;
- Don't handle SIOCGIFADDR specially, similar to r277103.
This change is based on a previous revision from Andy Zhang
(Microsoft) who did the diagnostic work and many thanks to
them for their help in supporting the HyperV work.
PR: kern/187203
MFC after: 2 weeks
Also ensure dsb precedes isb in all icache maintenance routines (first
do a data sync, then stall the instruction stream until it finishes).
Submitted by: Michal Meloun
in kern_gzio.c. The old gzio interface was somewhat inflexible and has not
worked properly since r272535: currently, the gzio functions are called with
a range lock held on the output vnode, but kern_gzio.c does not pass the
IO_RANGELOCKED flag to vn_rdwr() calls, resulting in deadlock when vn_rdwr()
attempts to reacquire the range lock. Moreover, the new gzio interface can
be used to implement kernel core compression.
This change also modifies the kernel configuration options needed to enable
userland core dump compression support: gzio is now an option rather than a
device, and the COMPRESS_USER_CORES option is removed. Core dump compression
is enabled using the kern.compress_user_cores sysctl/tunable.
Differential Revision: https://reviews.freebsd.org/D1832
Reviewed by: rpaulo
Discussed with: kib
an FDT. This is how Linux and OS X boot and can avoid some issues with
using Open Firmware at runtime. The code is highly experimental and disabled
by default; it can be turned on by setting the loader environment variable
"usefdt" to a non-NULL value.
confusion, the _setjmp.S in libstand was never being used and was instead
being shadowed by the libc version. Since the libc version now uses FPRs,
it caused loader to crash.
Otherwise, the initial media speed would change if a PHY is hooked up,
sending PHY speed notifications. For the AP135 at least, the RGMII
PHY has a static speed/duplex configured and if the PHY plumbing
attaches the PHY to the if_arge interface, the first link speed change
from 1000/full will set the MAC to something that isn't useful.
This shouldn't affect any other platforms - everything I looked at is
using hard-coded speed/duplex as static, as they're facing a switch
with no PHY attached.
All the per-port support is really doing is applying a port visibility
mask to each of the switchports. Everything still look like a single
portgroup (vlan id 1), but the per-port visibility mask is modified.
Whilst I'm here, also add some initial dot1q support - the pvid stuff
is doing the right thing, but it's not useful without the rest of
the VLAN table programming.
It's enough for me to be able to use the LAN/WAN port distinction
on the AP135, where there isn't (for now!) a dedicated PHY for the
"WAN" port.
Tested:
* AP135, QCA9558 SoC + AR8327 switch
been done by U-Boot. This allows the USB to work when we load the kernel
directly.
No dma sync is performed after these operations as the data we read/write
is not used by the cpu after the calls to the maimbox driver.
Differential Revision: https://reviews.freebsd.org/D1940
Reviewed by: imp, Michal Meloun (meloun AT miracle.cz)
MFC after: 1 Week
Sponsored by: ABT Systems Ltd
* Even though I got the registers around "right", it seems
I'm not tickling the MDIO access correctly for the internal PHY
bus. Some of the switches are fine poking at the external PHY
registers; others aren't. So, enable direct PHY bus access
for the AR8327, and leave the existing code in place for the
others.
* Go and shuffle the register access around. Whilst here,
restore the 2ms delay if changing page.
* Comment out some of the stub printf()s; there's some upcoming
work to add port VLAN support.
Tested:
* AP135 development board
* Carambola2 - AR9331 SoC
both the post-filter and post-thread callbacks.
Also eliminate a completely unecessary write to INTC_ISR_CLEAR register,
which clears a software-generated interrupt that can only happen with a
write to INTC_ISR_SET (which nothing does).
When a gpiobus child is added, use its name to identify the mapped pin
names.
Make the respective changes to libgpio.
Add a new '-n' flag to gpioctl(8) to set the pin name.
Differential Revision: https://reviews.freebsd.org/D2002
Reviewed by: rpaulo
Requested by: many
The vtophys() function is used to get the physical page address for
the virtually allocated frame buffers when a physically continuous
memory area is not available. This change also allows removing the
masking of the FB_FLAG_NOMMAP flag in the PS3 syscons driver.
The FB and VT drivers were tested using X.org/xf86-video-scfb and
syscons.
executables. The goal here, not yet accomplished, is to let the e500 kernel
run under QEMU by setting KERNBASE to something that fits in low memory and
then having the kernel relocate itself at runtime.
uart implementations, and export them using the new linker-set mechanism.
Differential Revision: https://reviews.freebsd.org/D1993
Submitted by: Michal Meloun
(class and device) FDT UART. Define second one, UART_FDT_CLASS, for UART
class only.
This paves the way for declaring uart_class data and ofw/fdt compat data
with a uart implementation, rather than needing a big global table of
compat data and weak-symbol declarations of every existing implementation.
Differential Revision: https://reviews.freebsd.org/D1992
Submitted by: Michal Meloun
netmap rx queues, and the "batchiness" of rx updates sent to the chip.
These knobs will probably become per-rxq in the near future and will be
documented only after their final form is decided.
MFC after: 1 month
