First, we were never correctly checking for a 24XX Status Type 0
response- that cased us to fall through to evaluate status for
commands as if this were a 2100/2200/2300 Status Type 0 response.
This is *close*, but not quite the same. This has been reported
to be apparent with some wierd lun configuration problems with
some arrays. It became glaringly apparent on sparc64 where none
of the correct byte swap things were done.
Fixing this omission then caused a whole universe shifting debug
cycle of endian issues for the 2400. The manual for 24XX f/w turns
out to be wrong about the endianness of a couple of entities. The
lun and cdb fields for the type 7 request are *not* unconditionally
big endian- they happen to be opposite of whatever the endian of
the current machine type is. Same with the sense data for the
24XX type 0 response.
While we're at it investigate and resolve some NVRAM endian
issues.
Approved by: re (ken)
MFC after: 3 days
request queues rather than shove it down a word at a time, we have
to remember to put it into little endian format. Use the macros
ISP_IOXPUT_{16,32} for this purpose. Otherwise, on sparc the firmware
is loaded garbled and we get a (not surprisingly) firmware checksum
failure and the card won't start and we don't attach it.
Approved by: re (bruce)
MFC after: 3 days
Seems to work on RELENG_4 through -current and also on sparc64
now. There may still be some issues with the auto attach/detach
code to sort out.
MFC after: 3 days
an ICB. This shows up on card restarts, and usually for
2200-2300 cards. What happens is that we start up,
attempting to acquire a hard address. We end up instead
being an F-port topology, which reports out a loop id
of 0xff (or 0xffff for 2K Login f/w). Then, if we restart,
we end up telling the card to go off an acquire this loop
address, which the card then rejects. Bah.
Compilation fixes from Solaris port.
front of isp_init so we can read NVRAM even if we're role ISP_NONE.
Prepare for reintroduction of channels (for FC) for N-Port
Virtualization.
Fix a botch in handle assignment that caused us to nuke one device
when a new one arrives and end up with two devices with the same
identity in the virtual target mapping table.
server.
Don't complain about a hard loop id of 0xffff- we get this in
point-to-point topologies with the 2300 and 2K Login firmware.
Up the timeout on register FC4 types commands.
with- not hope for the best. Change some things which were gated
off of 24XX to be gated off of 2K login support. Convert some
isp_prt calls to xpt_print calls.
and provied an isp_control entry point so that the outer layers can
do PLOGI/LOGO explicitly. Add MS IOCB support. This completes the cycle
for base support for SMI-S.
Only complain about FC Reponse errors if they're nonzero.
Shorten some PortID printouts for local loop.
Add an internal isp_xcmd_t data structure which we'll use for some
CT-Passthru support as part of adding SMI-S.
gone device timers and zombie state entries. There are tunables
that can be used to select a number of parameters.
loop_down_limit - how long to wait for loop to come back up before
declaring
all devices dead (default 300 seconds)
gone_device_time- how long to wait for a device that has appeared
to leave the loop or fabric to reappear (default 30 seconds)
Internal tunables include (which should be externalized):
quick_boot_time- how long to wait when booting for loop to come up
change_is_bad- whether or not to accept devices with the same
WWNN/WWPN that reappear at a different PortID as being the 'same'
device.
Keen students of some of the subtle issues here will ask how
one can keep devices from being re-accepted at all (the answer
is to set a gone_device_time to zero- that effectively would
be the same thing).
options field in register 10 will be deterministic, not random.
Correct the number of input bits for EXECUTE_FIRMWARE 0..1 to
0..2- the 2322 and 24XX cards use mailbox register 2 to specify
whether the f/w being executed is freshly loaded or not.
Correct the number of input bits for {READ,WRITE}_RAM_WORD_EXTENDED
so that register 8 gets picked up.
Fix the indexing and offset for the 2322 f/w download so that it
correctly puts the different code segments where they belong.
Move VERIFY_CHECKSUM to be the 'else' clause to 2322 f/w downloads-
the EXECUTE_FIRMWARE command for 2322 and 24XX cards will tell you
if the f/w checksum is incorrect and VERIFY_CHECKSUM only works for
RISC SRAM address < 64K so you can only do a VERIFY_CHECKSUM on the
first of the 3 f/w segments for the 2322.
Shorten the delay for the continuation mailbox commands- 1ms is
ridiculous (100us is more likely).
All of the more or less is really only for the 2322/6322 cards.
FreeBSD repository and to clean up the license header so as to
not pollute the license with file function.
Zero all mailbox structures prior to use (just in case). Change
the outgoing mailbox count for INIT_FIRMWARE to be correct.
Add MEMORY_BARRIER for the few scratch dma ops that were missing
them plus add a couple of hi 32 bit dma ops (we could probably
allow 64 bit scratch and request/response queue dma now).
(and by extension, the 2422).
One peculiar thing I've found with the 2322 is that if you
don't force it to do Hard LoopID acquisition, the firmware
crashes. This took a while to figure out.
While we're at it, fix various bugs having to do with NVRAM
reading and option setting with respect to pieces of NVRAM.
Pull in some target mode changes from a private branch.
Pull in some more RELENG_4 compilation changes.
A lot of lines changed, but not much content change yet.
to getting rid u_int for uint and so on).
b) Turn back on 64 bit DAC support. Cheeze it a bit in that we have two
DMA callback functions- one when we have bus_addr_t > 4 bits in width and
the other which should be normal. Even Cheezier in that we turn off setting
up DMA maps to be BUS_SPACE_MAXADDR if we're in ISP_TARGET_MODE. More work
on this in a week or so.
c) Tested under amd64 and 1MB DFLTPHYS, sparc64, i386 (PAE, but insufficient
memory to really test > 4GB). LINT check under amd64.
MFC after: 1 month
up to date. Principle changes for this reelase is to support 2K Port Login
firmware. This allows us to support the 2322 (and 2422 4Gb) cards which only
come with the 2K Port Login firmware. The 2322 should now work- but we don't
have firmware sets for it in ispfw (as the change to load 2K Port Login f/w
hasn't been made- that f/w is so big it has to be loaded in more than one
chunk).
Other changes are the beginnings of cleaning up some long standing target
mode issues. The next changes here will incorporate a lot of bug fixes
from others.
Finally, some copyright cleanup and attempts to make the parts of the
driver that are FreeBSD specific start conforming more to FreeBSD style.
MFC after: 1 month
Use the correct number of handles for multihandle returns.
Very, very, rarely on some SMP systems we've seen an 'unstable' type
in the response queue. I dunno whether or not it's a bug in our
handling, or whether there's a cache incoherency issue, but
try to guard against it.
MFC after: 2 weeks
fixes a longstanding issue WRT resetting the chip after startup- it
would fail if we were connected as an F-port to a switch. If we
were connected as an F-port, we got assigned a hard loop ID of 255,
which is really a bogus loop id. Then when we turned around to
reset ourselves, the firmware would reject the ICB_INIT request
because the loop id was bogus. *sputter*
Minor fixlet from somebody in NetBSD with too much time on their
hands (dma -> DMA).
