Submitted by Hiroyuki Aizu <eyes@navi.org>
(refer to [FreeBSD-users-jp 65061])
Tested by Hiroharu Tamaru <tamaru@myn.rcast.u-tokyo.ac.jp>
(refer to [bsd-usb:689])
drain routines are done by swi_net, which allows for better queue control
at some future point. Packets may also be directly dispatched to a netisr
instead of queued, this may be of interest at some installations, but
currently defaults to off.
Reviewed by: hsu, silby, jayanth, sam
Sponsored by: DARPA, NAI Labs
branches:
Initialize struct cdevsw using C99 sparse initializtion and remove
all initializations to default values.
This patch is automatically generated and has been tested by compiling
LINT with all the fields in struct cdevsw in reverse order on alpha,
sparc64 and i386.
Approved by: re(scottl)
Reading the PCI config space with the wrong (larger) size is not
a problem in this case, but writing can be as it clobbers unrelated
registers. In this case the clobbering is for reserved fields, which
too is mostly harmless... for now. Hence, this change is mostly
preventive in nature.
a number of related problems along the way.
- Automatically detect CDROM drives that can't handle 6 byte mode
sense and mode select, and adjust our command size accordingly.
We have to handle this in the cd(4) driver (where the buffers are
allocated), since the parameter list length is different for the
6 and 10 byte mode sense commands.
- Remove MODE_SENSE and MODE_SELECT translation removed in ATAPICAM
and in the umass(4) driver, since there's no way for that to work
properly.
- Add a quirk entry for CDROM drives that just hang when they get a 6
byte mode sense or mode select. The reason for the quirk must be
documented in a PR, and all quirks must be approved by
ken@FreeBSD.org. This is to make sure that we fully understand why
each quirk is needed. Once the CAM_NEW_TRAN_CODE is finished, we
should be able to remove any such quirks, since we'll know what
protocol the drive speaks (SCSI, ATAPI, etc.) and therefore whether
we should use 6 or 10 byte mode sense/select commands.
- Change the way the da(4) handles the no_6_byte sysctl. There is
now a per-drive sysctl to set the minimum command size for that
particular disk. (Since you could have multiple disks with
multiple requirements in one system.)
- Loader tunable support for all the sysctls in the da(4) and cd(4)
drivers.
- Add a CDIOCCLOSE ioctl for cd(4) (bde pointed this out a long
time ago).
- Add a media validation routine (cdcheckmedia()) to the cd(4)
driver, to fix some problems bde pointed out a long time ago. We
now allow open() to succeed no matter what, but if we don't detect
valid media, the user can only issue CDIOCCLOSE or CDIOCEJECT
ioctls.
- The media validation routine also reads the table of contents off
the drive. We use the table of contents to implement the
CDIOCPLAYTRACKS ioctl using the PLAY AUDIO MSF command. The
PLAY AUDIO TRACK INDEX command that we previously used was
deprecated after SCSI-2. It works in every SCSI CDROM I've tried,
but doesn't seem to work on ATAPI CDROM drives. We still use the
play audio track index command if we don't have a valid TOC, but
I suppose it'll fail anyway in that case.
- Add _len() versions of scsi_mode_sense() and scsi_mode_select() so
that we can specify the minimum command length.
- Fix a couple of formatting problems in the sense printing code.
MFC after: 4 weeks
some USB devices. (Make sure to set xfer data length when we force
a short inquiry.)
Obtained from: NetBSD(sys/dev/usb/umass_scsipi.c rev.1.8)
Original idea from: Shingo WATANABE <nabe@nabechan.org>
descriptor request, which usbd_get_string_desc() uses to get the
length of a descriptor. One device for instance returns a full 8
byte long packet instead which confuses the rest of the stack and
leads to the USB port being reset. The fix is to instead request
two bytes, but not to complain if we only get one.
Submitted by: kan
MFC after: 3 days
Metricom Ricochet GS modem. Add them here.
# A new umodem appears to be needed to make the sanyo phone work, but that's
# more extensive and will come after coordination.
command in case this setting was not saved. Since bandwidth reclamation
(-current only) often results in bus activity continuing to the end
of every frame, most transfers would fail with IOERROR if this
setting is missed.
Reviewed by: n_hibma
MFC after: 1 week
