i.e. alignment, max_address, max_iosize and segsize (only max_address is
thought to have an negative impact regarding this issue though), after
calling ata_dmainit() either directly or indirectly so these values have
no effect or at least no effect on the DMA tags and the defaults are used
for the latter instead. So change the drivers to set these parameters
up-front and ata_dmainit() to honor them.
Reviewd by: mav
MFC after: 1 month
- This adds a VM SRIOV interface, ixv, it is however
transparent to the user, it links with the ixgbe.ko,
but when ixgbe is loaded in a virtualized guest with
SRIOV configured this will be detected.
- Sync shared code to latest
- Many bug fixes and improvements, thanks to everyone
who has been using the driver and reporting issues.
the dev.fxp.%d.noflow tunable as the same effect can now be achieved with
ifconfig(8) by setting the flowcontrol media option as desired (besides
the tunable never having a chance to actually enable flow control support
so far).
In joint forces with: yongari
- Fix a bug where TCO_BOOT_STS was supposed to be cleared after
TCO_SECOND_TO_STS and not before.
Sponsored by: Sandvine Incorporated
Submitted by: Mark Johnston <mjohnston at sandvine dot com>
Reviewed by: des
MFC after: 10 days
support multi-queue but the hardware limitation made it hard to
implement supporting multi-queue. Allocating more than necessary
vectors is resource waste and it can be added back when we
implement multi-queue support.
number of retry to be performed whenever controller found RX
descriptor was empty. RX empty interrupt is generated only when the
retry counter is over. Experimentation shows retrying RX descriptor
loading increased number of dropped frames under flow-control
enabled environments so disable it and have controller generate RX
empty interrupt as fast as it can.
While I'm here fix RXCSR_DESC_RT_CNT macro.
(wrong unit number for a host controller) when the module is load /
unloaded repeatly. Attaching the USB pf is moved to usbus device's
attach.
Pointed by: yongari
disable ASPM L0S and L1 LINK states on 82573, 82574,
and 82583. The theory is that this is behind certain
hangs being experienced by some customers.
Also included a small optimization in the rxeof routine
that was in my internal code.
Change the PBA size for pchlan, it was incorrect.
MFC after: 3 days
- Fixes from John Baldwin: vlan shadow tables made per/interface,
make vlan hw setup only happen when capability enabled, and
finally, make a tuneable interrupt rate. Thanks John!
- Tweaked watchdog handling to avoid any false positives, now
detection is in the TX clean path, with only the final check
and init happening in the local timer.
- limit queues to 8 for all devices, with 82576 or 82580 on
larger machines it can get greater than this, and it seems
mostly a resource waste to do so. Even 8 might be high but
it can be manually reduced.
- use 2k, 4k and now 9k clusters based on the MTU size.
- rework the igb_refresh_mbuf() code, its important to
make sure the descriptor is rewritten even when reusing
mbufs since writeback clobbers things.
MFC: in a few days, this delta needs to get to 8.2
Shorten the descriptive strings for Huawei devices. The vendor or
operator name should not be included in the device name.
Submitted by: Emile Coetzee
MFC after: 3 days
- Partially revert r172334; as it turns out the DELAYs in gem_reset_{r,t}x()
are actually necessary although bus space barriers and gem_bitwait() are
used, otherwise the controller may trigger an IOMMU errors on at least
sparc64. This is in line with what Linux and OpenSolaris do.
- Add some DSP init code for BCM5221. The values derived from Apple's GMAC
driver and the same init code also exists in Linux's sungem_phy driver.
- Only read media status bits when they are valid.
Obtained from: NetBSD, OpenBSD
autonegotiation along with manual media selection and also only report flow
control status when BMCR_AUTOEN is set (at least with gentbi(4) determining
the flow control status results in false-positives when not set), use
MIIF_NOMANPAUSE.
autonegotiation along with manual media selection and ukphy_status() also
only reports flow control status when BMCR_AUTOEN is set (at least with
gentbi(4) determining the flow control status results in false-positives
when not set), use MIIF_NOMANPAUSE.
The Myri10GE NIC will assume all TSO frames contain partial checksum,
and will emit TSO segments with bad TCP checksums if a TSO frame
contains a full checksum. The mxge driver takes care to make sure
that TSO is disabled when checksum offload is disabled for this
reason. However, modules that modify packet contents (like pf) may
end up completing a checksum on a TSO frame, leading to the NIC emitting
TSO segments with bad checksums.
To workaround this, restore the partial checksum in the mxge driver
when we're fed a TSO frame with a full checksum.
Reported by: Bob Healey
MFC after: 3 days
packets which go through each USB host controllers. Its implementations
are almost based on BPF code and very similar with it except it's
little bit customized for USB packet only. The userland program
usbdump(8) would be committed soon.
Discussed with: hps, thompsa, yongari
