author can't remember why it was there.
The CTS_SCSI_FLAGS_TAG_ENB remains in place, and makes sense, and is
checked all over the place.
The CTS_SPI_FLAGS_TAG_ENB was probably an attempt to distinguish
protocol and transport tag capabilities. At the very least this can
be confusing and prone to many bugs, so let's just assume that the
transport tag case just flows from the protocol (and vice versa)
for now.
the ORDERED tag. This recoups significant performance gains for many
arrays.
The default is still to send out the ORDERED tag periodically.
Reviewed by: scsi (justin+timeout)
the CAM_NEW_TRAN_CODE that has been in the tree for some years now.
This first step consists solely of adding to or correcting
CAM_NEW_TRAN_CODE pieces in the kernel source tree such
that a both a GENERIC (at least on i386) and a LINT build
with CAM_NEW_TRAN_CODE as an option will compile correctly
and run (at least with some the h/w I have).
After a short settle time, the other pieces (making
CAM_NEW_TRAN_CODE the default and updating libcam
and camcontrol) will be brought in.
This will be an incompatible change in that the size of structures
related to XPT_PATH_INQ and XPT_{GET,SET}_TRAN_SETTINGS change
in both size and content. However, basic system operation and
basic system utilities work well enough with this change.
Reviewed by: freebsd-scsi and specific stakeholders
and CAM_RESRC_UNAVAIL returns. Delay a tunable amount for
either between retries.
This came up because the MPT IOC was returning "IOC out of
resources" for some user and this caused a CAM_RESRC_UNAVAIL
return. Putting a bit of delay between retries helped them
out.
There was some discussion that an async event should be used
to clear CAM_RESRC_UNAVAIL. That's probably a better notion
eventually.
Reviewed by: scsi@freebsd.org (ade, scott)
MFC after: 1 week
REPORT LUNS command to a device.
camcontrol.[c8]: Implement reportluns. This tries to print the LUNs
out in a reasonable format. Only the periph
addressing method has been tested, since very little
hardware that I know of supports the other methods.
scsi_all.[ch]: Revamp the report luns CDB structure and helper
functions. This constitutes a little bit of an API
change, but since the old CDB length was 10 bytes,
and the REPORT LUNS CDB length is actually 12 bytes,
it's clear that no one was using this API in the
first place.
MFC After: 1 week
what to do with it.
This forces us to scan targets sequentially, not in parallel.
The reason we might want to do this is that SPI negotiation
might not work right at the SIM level if we try to do it
in parallel. We *could* fix this for each SIM where this is
broken, but it's a lot harder to do that when we can simply
ask CAM to probe sequentially.
If PIM_SEQSCAN is not set (default), the original behaviour for
probing is unchanged.
LUN probing is still done in parallel for each target in either
case.
While we're at it, clean up some resource leakage for error
cases.
Reviewed by: ken, scott, scsi@
MFC after: 1 week
usage as of SPC2r20. Specifically, handle the BQueue
flag which will indicate that a device supports the
Basic Queueing model (no Head of Queue or Ordered tags).
When this flag is set, SID_CmdQueue is clear. This has
causes FreeBSD to assume that the device did not support
tagged operations.
MFC after: 1 month
This version of scsi_target.c removes all SMP locking until
we have a lock-aware CAM stack. This allows us to use KNOTE
without a panic at least.
It's not yet clear whether target mode is working yet or not.
Discussed with: Scott, Ken, Nate, Justin
return to user space w/o waiting for I/O to complete.
I tried to get several folks who know this code better than me to review it
with no luck. I *do* know that w/o this code, using the SCSI target driver
panics in userret (if it doesn't panic in knote first).
an application to upon a tape (yea, even the non-control device) even if
it cannot establish a mount session. If the open cannot establish a mount
session and O_NONBLOCK was specified, the tape becomes 'open pending mount'.
All I/O operations that would require access to a tape thereafter until
a close attempt to initiate the mount session. If the mount session succeeds,
the tape driver transitions to full open state, else returns an appropriate
I/O error (ENXIO).
At the same time, add a change that remembers whether tape is being opened
read-only. If so, disallow 'write' operations like writing filemarks that
bypass the normal read-only filtering operations that happen in the write(2)
syscall.
Reviewed by: ken, justin, grog
MFC after: 2 weeks
Suggested by: The Bacula Team
operations before returning. Point the bus at a dummy cam_sim
structure so that any CCBs will complete immediately with a
CAM_DEV_NOT_THERE status, and ensure that any xpt_schedule() calls
on the bus's devices will immediately call the peripheral's
periph_start() routine. Also repeat the async messages because
devices that were part of the way through being probed may appear
after the original AC_LOST_DEVICE was sent, and would otherwise
never go away.
These changes make it possible to deregister a bus and free the SIM
at most stages during bus probing without the usual crashes in
camisr(). In particular, plugging in a umass device and then
unplugging it as soon as the first probe messages appeared would
almost always result in a crash. Now the device just goes away with
a few CAM errors and all references to the CAM bus, target and
device are dropped correctly.
CAM_LUN_INVALID or CAM_TID_INVALID. Retries were being triggered
here when a umass device was unplugged, and while the retries
themselves are probably harmless, they complicated finding the real
SIM removal problems.
the underlying drive had been hot-unplugged from the system. Here
is a specific example. Filesystem code had opened /dev/da1s1e.
Subsequently, the drive was hot-unplugged. This (correctly) caused
all of the associated /dev/da1* entries to be deleted. When the
filesystem later realized that the drive was gone it closed the
device, reducing the write-access counts to 0 on the geom providers
for da1s1e, da1s1, and da1. This caused geom to re-taste the
providers, resulting in the devices being created again. When the
drive was hot-plugged back in, it resulted in duplicate /dev entries
for da1s1e, da1s1, and da1.
This fix adds a new disk_gone() function which is called by CAM when a
drive goes away. It orphans all of the providers associated with the
drive, setting an error condition of ENXIO in each one. In addition,
we prevent a re-taste on last close for writing if an error condition
has been set in the provider.
Sponsored by: Isilon Systems
Reviewed by: phk
MFC after: 1 week
tunable (until we get REPORT LUNS in place).
If we're probing luns, and each probe succeeds, we keep going past
lun 7 if we're a SCSI3 or better device (until we fail to probe).
If we're probing luns, and a probe fails, we only keep going if
we're quirked *for* it (CAM_QUIRK_HILUNS), and if we're not quirked
*against* it (CAM_QUIRK_NOHILUNS), or we're a SCSI3 or better device
and the tunable (kern.cam.cam_srch_hi) is set non-zero.
Reviewed by: nate@rootlabs.org, gibbs@scsiguy.com, ken@kdm.com, scottl@samsco.org
MFC after: 1 week
