kern_sendfile() uses vm_rdwr() to read-ahead blocks of data to populate
page cache. When sendfile stumbles upon a page that is not populated
yet, it sends out all the mbufs that it collected so far. This
resulted in very poor performance with ZFS when file data is not in the
page cache, because ZFS vop_read for UIO_NOCOPY case populated only
those pages that are already in cache, but not valid. Which means that
most of the time it populated only the first requested page in the
described above scenario.
Reported by: Alexander Zagrebin <alexz@visp.ru>
Tested by: Alexander Zagrebin <alexz@visp.ru>,
Artemiev Igor <ai@kliksys.ru>
MFC after: 12 days
Also, add a comment mentioning _PSD - on some systems it's enough to
put one logical CPU into a particular P-state to make other CPUs in
the same domain to enter that P-state.
Also, call sched_unbind() after the loop - sched_bind() automatically
rebinds from previous CPU to a new one, and the new arrangement of code
is safer against early loop exit.
Plus one minor style nit.
MFC after: 10 days
vnets to select their own default CC algorithm independent of each other and the
base system. If the base system or a vnet has set a default which gets unloaded,
we reset that netstack's default to NewReno.
Sponsored by: FreeBSD Foundation
Tested by: Mikolaj Golub <to.my.trociny at gmail com>
Reviewed by: bz (briefly)
MFC after: 3 months
is small, so there is no good reason not to declare the buffer at the top.
- Fix a whitespace nit.
Sponsored by: FreeBSD Foundation
MFC after: 11 weeks
X-MFC with: r215166
Any found to be using the algorithm that is about to go away are switched back
to NewReno to avoid leaving dangling pointers which would trigger a panic. For
VIMAGE kernels, there is a list per vnet to walk, yet the implementation was
only examining one of the vnet lists.
Fix the implementation of the above feature for VIMAGE kernels by looping
through all active TCP control blocks across all vnets.
Sponsored by: FreeBSD Foundation
Tested by: Mikolaj Golub <to.my.trociny at gmail com>
Reviewed by: bz (briefly)
MFC after: 11 weeks
runs on boot and each time a vnet jail is created. Running cc_init() multiple
times results in a panic when attempting to initialise the cc_list lock again,
and so r215166 effectively broke the use of vnet jails.
Switch to using a SYSINIT to run cc_init() on boot. CC algorithm modules loaded
on boot register in the same SI_SUB_PROTO_IFATTACHDOMAIN category as is used in
this patch, so cc_init() is run at SI_ORDER_FIRST to ensure the framework is
initialised before module registration is attempted.
Sponsored by: FreeBSD Foundation
Reported and tested by: Mikolaj Golub <to.my.trociny at gmail com>
MFC after: 11 weeks
X-MFC with: r215166
it exists in order to allow arch-specific overrides. This fixes the
binutils (and world) build on powerpc64 after recent TBEMD merges.
Reviewed by: imp
of the MAC driver in order to attach miibus(4) on the first pass instead of
falling through to also calling it on the device_t of miibus(4). The latter
code flow was intended to attach the PHY drivers the same way regardless of
whether it's the first or a repeated pass, modulo the bus_generic_attach()
call in miibus_attach() which shouldn't be there. However, it turned out
that these variants cause miibus(4) to be attached twice under certain
conditions when using MAC drivers as modules.
Submitted by: yongari
MFC after: 3 days
BIOS does not support ACPI. The other options in the menu retain their
existing numbers, option 2 is simply blanked out (and '2' is ignored).
MFC after: 1 month
unsupported futex operation
- for those futex operations which are known to be not supported,
print out which futex operation it is
- shortcut the error return of the unsupported FUTEX_CLOCK_REALTIME in
some cases:
FUTEX_CLOCK_REALTIME can be used to tell linux to use
CLOCK_REALTIME instead of CLOCK_MONOTONIC. FUTEX_CLOCK_REALTIME
however must only be set, if either FUTEX_WAIT_BITSET or
FUTEX_WAIT_REQUEUE_PI are set too. If that's not the case
we can die with ENOSYS right at the beginning.
Submitted by: arundel
Reviewed by: rdivacky (earlier iteration of the patch)
MFC after: 1 week
not provide any MAC configuration interface for resolved flow
control parameters. There is even no register that configures water
mark which will control generation of pause frames.
However enabling flow control surely enhanced performance a lot.
such that nfe(4) does not work with MSI-X. When MSI-X support was
introduced, I remember MCP55 controller worked without problems so
the issue could be either PCI bridge or BIOS issue. But I also
noticed snd_hda(4) disabled MSI on all MCP55 chipset so I'm still
not sure this is generic issue of MCP55 chipset. If this was PCI
bridge issue we would have added it to a system wide black-list
table but it's not clear to me at this moment whether it was caused
by either broken BIOS or silicon bug of MCP55 chipset.
To workaround the issue, maintain a MSI/MSI-X black-list table in
driver and lookup base board manufacturer and product name from the
table before attempting to use MSI-X. If driver find an matching
entry, nfe(4) will not use MSI/MSI-X and fall back on traditional
INTx mode. This approach should be the last resort since it relies
on smbios and if another instance of MSI/MSI-X breakage is reported
with different maker/product, we may have to get the PCI bridge
black-listed instead of adding an new entry.
PR: kern/152150
K3765 datacard. After ejecting this device, it reappears using
the normal K3765 ID. It does not switch automatically
Reviewed by: n_hibma
Obtained from: OpenBSD
MFC after: 2 weeks
The ports/Mk/bsd.port.mk uses sys/param.h to fetch osrel, and cannot
grok several constants with the prefix.
Reported and tested by: swell.k gmail com
MFC after: 1 week