If we fail noise floor calibration then we may end up with a deaf NIC
which we can't recover without a full chip reset.
Earlier chips seem to get less stuck in this condition versus AR9280/later
and AR9300/later, but whilst here just fix up the AR5212 era chips to also
return NF calibration failures.
This HAL routine would only return failure if the channel was not configured.
This is a no-op until the driver side code for doing resets and the HAL
code for being told about the reset type (and then handling it!) is
implemented.
Tested:
* AR9280, STA mode
* AR2425, STA mode
* AR9380, STA mode
I'm in the process of reworking how the reset path works with an eye
to better recovery when the chips hang and/or go RF/PHY deaf.
This is the first step in a lot of unification and API changes.
This fixes 32-bit compat (no ioctl command defintions are required
as struct ifreq is the same size). This is believed to be sufficent to
fully support ifconfig on 32-bit systems.
Reviewed by: kib
Obtained from: CheriBSD
MFC after: 1 week
Relnotes: yes
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D14900
For DWDS VAPs on ath(4) we need to ensure that the STA vap and hostap VAP
have different MAC addresses. If the STA code path doesn't utilise the
address assign / reclaim path then it doesn't update the bitmap with which
address was allocated.
This should fix a bunch of corner issues I've been seeing with DWDS STA + AP
VAPs that I was working around with manual MAC address assignment.
Uses of mallocarray(9).
The use of mallocarray(9) has rocketed the required swap to build FreeBSD.
This is likely caused by the allocation size attributes which put extra pressure
on the compiler.
Given that most of these checks are superfluous we have to choose better
where to use mallocarray(9). We still have more uses of mallocarray(9) but
hopefully this is enough to bring swap usage to a reasonable level.
Reported by: wosch
PR: 225197
Focus on code where we are doing multiplications within malloc(9). None of
these is likely to overflow, however the change is still useful as some
static checkers can benefit from the allocation attributes we use for
mallocarray.
This initial sweep only covers malloc(9) calls with M_NOWAIT. No good
reason but I started doing the changes before r327796 and at that time it
was convenient to make sure the sorrounding code could handle NULL values.
Apply the fix from r327499 to additional ioctl handlers.
Reported by: Ilja van Sprundel <ivansprundel@ioactive.com>
MFC after: 1 week
MFC with: r327499
Sponsored by: The FreeBSD Foundation
The ath_btcoex_ioctl handler allocated a buffer without M_ZERO and
returned it to userland without writing to it.
The device has permissions only for root so this is not urgent, and the
fix can be MFCd and considered for a future EN.
Reported by: Ilja van Sprundel <ivansprundel@ioactive.com>
Submitted by: Domagoj Stolfa <domagoj.stolfa@gmail.com>
Reviewed by: adrian
MFC after: 1 week
This removes the direct WME info access in the ieee80211com struct and instead
provides a method of fetching the data. Right now it's a no-op but eventually
it'll turn into a per-VAP method for drivers that support it (eg iwn, iwm,
upcoming ath10k work) as things like p2p support require this kind of behaviour.
Tested:
* ath(4), STA and AP mode
TODO:
* yes, this is slightly stack size-y, but it is an important first step
to get drivers migrated over to a sensible WME API. A lot of per-phy things
need to be converted to per-VAP before P2P, 11ac firmware, etc stuff shows up.
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
As part of ath10k and other chipset support, the EDCA stuff has to be moved
to potentially be per-VAP. For hardware that doesn't support it (ie,
everything that we currently support) it can just fetch the "current"
global EDCA parameters for the NIC.
This is one of those parameters that is linked to the currently active
channel context / VAP in Linux mac80211 parlance.
Tested:
* ath(4), STA and AP modes
It turned out, that some models of the Atheros PCIe
adapters (e.g. AR983x family) may fail to attach
due to insufficient timeout value.
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Reviewed by: adrian
Differential revision: https://reviews.freebsd.org/D10903
In the deep past, when this code compiled as a binary module, ath_hal
built as a module. This allowed custom, smaller HAL modules to be built.
This was especially beneficial for small embedded platforms where you
didn't require /everything/ just to run.
However, sometime around the HAL opening fanfare, the HAL landed here
as one big driver+HAL thing, and a lot of the (dirty) infrastructure
(ie, #ifdef AH_SUPPORT_XXX) to build specific subsets of the HAL went away.
This was retained in sys/conf/files as "ath_hal_XXX" but it wasn't
really floated up to the modules themselves.
I'm now in a position where for the reaaaaaly embedded boards (both the
really old and the last couple generation of QCA MIPS boards) having a
cut down HAL module and driver loaded at runtime is /actually/ beneficial.
This reduces the kernel size down by quite a bit. The MIPS modules look
like this:
adrian@gertrude:~/work/freebsd/head-embedded/src % ls -l ../root/mips_ap/boot/kernel.CARAMBOLA2/ath*ko
-r-xr-xr-x 1 adrian adrian 5076 May 23 23:45 ../root/mips_ap/boot/kernel.CARAMBOLA2/ath_dfs.ko
-r-xr-xr-x 1 adrian adrian 100588 May 23 23:45 ../root/mips_ap/boot/kernel.CARAMBOLA2/ath_hal.ko
-r-xr-xr-x 1 adrian adrian 627324 May 23 23:45 ../root/mips_ap/boot/kernel.CARAMBOLA2/ath_hal_ar9300.ko
-r-xr-xr-x 1 adrian adrian 314588 May 23 23:45 ../root/mips_ap/boot/kernel.CARAMBOLA2/ath_main.ko
-r-xr-xr-x 1 adrian adrian 23472 May 23 23:45 ../root/mips_ap/boot/kernel.CARAMBOLA2/ath_rate.ko
And the x86 versions, like this:
root@gertrude:/home/adrian # ls -l /boot/kernel/ath*ko
-r-xr-xr-x 1 root wheel 36632 May 24 18:32 /boot/kernel/ath_dfs.ko
-r-xr-xr-x 1 root wheel 134440 May 24 18:32 /boot/kernel/ath_hal.ko
-r-xr-xr-x 1 root wheel 82320 May 24 18:32 /boot/kernel/ath_hal_ar5210.ko
-r-xr-xr-x 1 root wheel 104976 May 24 18:32 /boot/kernel/ath_hal_ar5211.ko
-r-xr-xr-x 1 root wheel 236144 May 24 18:32 /boot/kernel/ath_hal_ar5212.ko
-r-xr-xr-x 1 root wheel 336104 May 24 18:32 /boot/kernel/ath_hal_ar5416.ko
-r-xr-xr-x 1 root wheel 598336 May 24 18:32 /boot/kernel/ath_hal_ar9300.ko
-r-xr-xr-x 1 root wheel 406144 May 24 18:32 /boot/kernel/ath_main.ko
-r-xr-xr-x 1 root wheel 55352 May 24 18:32 /boot/kernel/ath_rate.ko
.. so you can see, not building the whole HAL can save quite a bit.
For example, if you don't need AR9300 support, you can actually avoid
wasting half a megabyte of RAM. On embedded routers this is quite a
big deal.
The AR9300 HAL can be later further shrunk because, hilariously,
it indeed supports AH_SUPPORT_<xxx> for optionally adding chipset support.
(I'll chase that down later as it's quite a big savings if you're only
building for a single embedded target.)
So:
* Create a very hackish way to load/unload HAL modules
* Create module metadata for each HAL subtype - ah_osdep_arXXXX.c
* Create module metadata for ath_rate and ath_dfs (bluetooth is
currently just built as part of it)
* .. yes, this means we could actually build multiple rate control
modules and pick one at load time, but I'd rather just glue this
into net80211's rate control code. Oh well, baby steps.
* Main driver is now "ath_main"
* Create an "if_ath" module that does what the ye olde one did -
load PCI glue, main driver, HAL and all child modules.
In this way, if you have "if_ath_load=YES" in /boot/modules.conf
it will load everything the old way and stuff should still work.
* For module autoloading purposes, I actually /did/ fix up
the name of the modules in if_ath_pci and if_ath_ahb.
If you want to selectively load things (eg on ye cheape ARM/MIPS platforms
where RAM is at a premium) you should:
* load ath_hal
* load the chip modules in question
* load ath_rate, ath_dfs
* load ath_main
* load if_ath_pci and/or if_ath_ahb depending upon your particular
bus bind type - this is where probe/attach is done.
TODO:
* AR5312 module and associated pieces - yes, we have the SoC side support
now so the wifi support would be good to "round things out";
* Just nuke AH_SUPPORT_AR5416 for now and always bloat the packet
structures; this'll simplify other things.
* Should add a simple refcnt thing to the HAL RF/chip modules so you
can't unload them whilst you're using them.
* Manpage updates, UPDATING if appropriate, etc.
This brings the AHB support in line with the PCI support - now other "things"
can wrap up the calibration / board data into a firmware blob and have them
probe/attach after the system has finished booting.
Note that this change requires /all/ of the AHB using kernel configurations
to change - so until I drop those changes in, this breaks AHB.
Fear not, I'll do that soon.
TODO:
* the above stuff.
Tested:
* AR9331, carambola 2, loading if_ath / wlan as modules at run time
When I initially did this 11n TX work in days of yonder, my 802.11 standards
clue was ... not as finely tuned. One of the things in 802.11-2012 (which
I guess technically was after I did this work, but I'm sure it was like this
in the previous rev?) is that among other traffic classes, three things are
important:
* group addressed frames should be default non-QoS, even if they're QoS frames, and
* group addressed frames should have a seqno out of a different space than the
per-TID QoS one; and because of this
* group addressed frames, being non-QoS, should never be in the Block-ACK window
for TX.
Now, net80211 and now this code cheats by using the non-QOS TID, but ideally
we'd introduce a separate seqno space just for multicast/group traffic for
TX and RX comparison.
Later extensions (eg reliable multicast / multimedia) express what one should do
when doing multicast traffic in a TID. Now, technically we /could/ do group traffic
as QoS traffic and throw it into a per-TID seqno space, but this definitely
introduces ordering issues when you take into account things like CABQ behaviour.
(Ie, if some traffic in the TID goes into the CABQ and some doesn't, because
it's doing a split of multicast and non-multicast traffic, then you have
seqno ordering issues.)
So, until someone implements 802.11vv reliable multicast / multimedia extensions,
group traffic is non-QoS.
Next, software/hardware queue TID mapping. In the past I believed the WME tagging
of frames because well, net80211 had a habit of tagging things like management
traffic with it. But, then we also map QoS traffic categories to TIDs as well.
So, we should obey the TID! But! then it put some management traffic into higher
WME categories too, as those frames don't have QoS TIDs. But! It'd do things like
put things like QoS action frames into higher WME categories, when they should
be kept in-order with the rest of the traffic for that TID. So! Given all of this,
the ath(4) driver does overrides to not trust the WME category.
I .. am undoing some of this. Now, the TID has a 1:1 mapping to the hardware
queue. The TID is the primary source of truth now for all QoS traffic.
The WME is only used for non-QoS traffic. This now means that any TID traffic
queued should be consistently queued regardless of WME, so things like the
"TX finished, do more TX" that is occuring right now for transmit handling
should be "better".
The consistent {TID, WME} -> hardware queue mapping is important for
transmit completion. It's used to schedule more traffic for that
particular TID, because that {many TID}:{1 TXQ} mapping in ath_tx_tid_sched()
is used for driving completion. Ie, when the hardware queue completes,
it'll walk that list of scheduled TIDs attached to that TXQ.
The eventual aim is to get ready for some other features around putting
some data into other hardware queues (eg for better PS-POLL support,
uAPSD, support, correct-er TDMA support, etc) which requires that
I tidy all of this up in preparation for then introducing further
TID scheduling that isn't linked to a hardware TXQ (likely a per-WME, per-TID
driver queue, and a per-node driver queue) to enable that.
Tested:
* AR9380, STA mode
* AR9380, AR9580, AP mode
Renumber cluase 4 to 3, per what everybody else did when BSD granted
them permission to remove clause 3. My insistance on keeping the same
numbering for legal reasons is too pedantic, so give up on that point.
Submitted by: Jan Schaumann <jschauma@stevens.edu>
Pull Request: https://github.com/freebsd/freebsd/pull/96
This implements hardware assisted quiet IE support. Quiet time is
an optional interval on DFS channels (but doesn't have to be DFS
only channels! sigh) where the station and AP can be quiet in order
to allow for channel utilisation measurements. Typically that's
stuff like radar detection, spectral scan, other-BSS frame sniffing,
checking how busy the air is, etc.
The hardware implements it as one of the generic timers, which is
supplied a period, offset from the trigger period and duration
to stay quiet. The AP can announce quiet time configurations which
change, and so this code also tracks that.
Implementation details:
* track the current quiet time IE
* compare the new one against the previous one - if only the TBTT
counter changes, don't update things
* If tbttcount=1 then program it into the hardware - that is when
it is easiest to program the correct starting offset (one TBTT +
configured offset).
* .. later on check to see if it can be done on any tbttcount
* If the IE goes away then remove the quiet timer and clear the
config
* Upon reset, state change, new beacon - clear quiet time IE
and just let it resync from the next beacon.
History:
This was work done initially by sibridgetech.com in 2011/2012/2013
as part of some FreeBSD wifi DFS contracting work they had for a
third party. They implemented the net80211 quiet time IE pieces
and had some test code for the station side which didn't entirely
use the timers correctly.
I figured out how to use the timers correctly without stopping/starting
the transmit DMA engine each time. When done correctly, the timer
just needs to be programmed once and left alone until the next
configuration change.
So, thanks to Himali Patel and Parthiv Shah for their work way
back then. I finally figured it out and finished it!
TODO:
* Now, I'd rather net80211 did the quiet time IE tracking and parsing,
pushing configurations into the driver is needed. I'll look at
doing that in a subsequent update.
* This doesn't handle multiple quiet time IEs, which will currently
just mess things up. I'll look into supporting that in the future
(at least by only obeying "one" of them, and then ignoring
subsequent IEs in a beacon/probe frame.)
* This also implements the STA side and not the AP side - the AP
side will come later, and involves taking various other intervals
into account (eg the beacon offset for multi-VAP modes, the
SWBA time, etc, etc) as well as obtaining the configuration when
a beacon is configured/generated rather than "hearing" an IE.
* .. investigate supporting quiet IE in mesh, tdma, ibss modes
* .. investigate supporting quiet IE for non-DFS channels
(so this can be done for say, 2GHz channels.)
* Chances are i should commit NULL methods for the ar5210, ar5211 HALs..
Tested:
* AR9380, STA mode - announcing quiet, removing quiet, changing quite
time config, whilst doing iperf testing;
* AR9380, AP mode.
* Although the hardware is awake, the power state handling doesn't think so.
So just explicitly wake it up early in setup so ath_hal calls don't complain.
* We shouldn't be transmitting or ACKing frames during DFS CAC or on passive
channels before we hear a beacon. So, start laying down comments in the
places where this work has to be done.
Note:
* The main bit missing from finishing this particular bit of work is a state
call to transition a VAP from passive to non-passive when a beacon is heard.
CAC is easy, it's an interface state. So, I'll go and add a method to control
that soon.
* limit cabq to 64 - in practice if this stays at ath_txbuf then
all buffers can be tied up by a very busy broadcast domain (eg ARP
storm, way too much MDNS/NETBIOS). It's been like this in the
freebsd-wifi-build AP project for the longest time.
* Now that I figured out the hilarity inherent in aggregate forming
and AR9380 EDMA work, change the per-node to 64 frames by default.
I'll do some more work to shorten the queue latency introduced when
doing data so TCP isn't so terrible, but it's now no longer /always/
tens of milliseconds of extra latency when doing active iperf tests.
Notes:
The reason for the extra latency is partly tx/rx taskqueue handling and
scheduling, and partly due to a lack of airtime/QoS awareness of per-node
traffic. Ideally we'd have different limits/priorities on the QoS/TID
levels per node so say, voice/video data got a better share of buffer
allocations over best effort/bulk data, but we currently don't implement
that. It's not /hard/ to do, I just need to do it.
Tested:
* AR9380 (STA), AR9580 (hostap) - both with the relevant changes.
TCP is now at around 180mbit with rate control and RTS protection
enabled. UDP stays at 355mbit at MCS23, no HT protection.
This is two fixes, which establishes what I /think/ is pretty close to the
theoretical PHY maximum speed on the AR9380 devices.
* When doing A-MPDU on a TID, don't queue to the hardware directly if
the hardware queue is busy. This gives us time to get more packets
queued up (and the hardware is busy, so there's no point in queuing
more to the hardware right now) to potentially form an A-MPDU.
This fixes up the throughput issue I was seeing where a couple hundred
single frames were being sent a second interspersed between A-MPDU
frames. It just happened that the software queue had exactly one
frame in it at that point. Queuing it until the hardware finishes
transmitting isn't exactly costly.
* When determining whether to dequeue from a software node/TID queue into
the hardware queue, fix up the checks to work right for EDMA chips
(ar9380 and later.) Before it was not dispatching anything until
the FIFO was empty. Now we allow it to dispatch another aggregate
up to the hardware aggregate limit, like I intended with the earlier
work.
This allows a 5GHz HT40, short-GI, "htprotmode off" test at MCS23
to achieve 357 Mbit/sec in a one-way UDP test. The stars have to be
aligned /just right/ so there are no retries but it can happen.
Just don't expect it to work in an OTA test if your 2yo is running
around the room - MCS23 is very very sensitive to channel conditions.
Tested:
* AR9380 STA (test) -> AR9580 hostap
TODO:
* More thorough testing on pre-AR9380 chips (AR5416, AR9160, AR9280)
* (Finally) teach ath_rate_sample about throughput/latency rather than
air time, so I can get good transmit rates with a 2yo running around.
When investigating performance on UDP TX on the AR9380 I found that the
following sequence was occuring:
* INTR
* EINPROGRESS - nothing yet
* INTR
* TXSTATUS - process a TX completion for an aggregate
* INTR, INTR
* TXSTATUS - process a TX completion for an aggregate
* TXD, TXD ... populate frames from the hardware queue and submit
What should be happening is a completed TXSTATUS fires off more packets
that are queued on active TIDs.
What /was/ happening was after that first TXSTATUS the TX queue hardware queue
was still empty, so it didn't push anything into the FIFO. Only after the
second TXSTATUS did any progress get made.
This is one of two commits - it ensures that the software TX queue scheduler
is called /after/ TX completion, otherwise no frames from the software staging
queues will be processed into the hardware queues.
The second commit will fix it so it populates aggregate frames correctly
when the above occurs - right now ath_txq_sched() is called, but it doesn't
populate anything because its pre-check conditions are wrong.
Whilst here, add/tweak debugging.
Tested:
* AR9380 STA (testing device) -> AR9580 hostap
This is supposed to only be applied to the first subframe and only if
RTS/CTS is being done. I'm still not yet checking RTS/CTS exchange status
so it's just happening for all subframes on AR9380 and later.
This gets MCS23 throughput up from around 250mbit to 303mbit with RTS/CTS
protection enabled, and around 330mbit with no HT protection enabled.
Now, MCS23 has a PHY rate of 450mbit and we should be seeing closer to
400mbit for a straight one-way UDP test, but this beats the previous
maximum throughput.
Tested:
* AR9380 (STA) -> AR9580 (AP) - STA with the modifications, doing UDP TX
test using iperf.
Set both IEEE80211_HTCAP_LDPC and IEEE80211_HTC_TXLDPC capability flags
if LDPC is supported + set 'do_ldpc = 1' only when it is not disabled,
not just supported.
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D9277
A recent change enforced the VAP limit as well as the peer limit.
I now need to actually set iv_ampdu_limit or we don't transmit more
than 8K sized aggregates.
This restores the expected (suboptimal, but still much faster) behaviour.
Tested:
* AR9380, STA mode
The HT40 channel population logic was "just" doing pairs of channels starting with
the band entry frequency. Trouble is, a lot of the rules start way off at 5120MHz,
which isn't a valid 5GHz channel. Then, eg for HT40U, it would populate:
* (5120,5140)
* (5160,5180)
* (5200,5220)
* (5240,5260)
.. as the HT40U pairs, with the first being the primary channel. Channel 36
is 5180MHz, and since it's not a primary channel here, it wouldn't populate it.
Then, the next HT40U would be 5200/5220, which is highly wrong.
HT40D had the same problem.
So, this just forces that 5GHz HT40 channels start at channel 36 (5180),
no matter what the band edge says. This includes eg doing 4.9GHz channels.
This erm, meant that the HT40 channels for the low band was always wrong.
Oops!
Tested:
* AR9380, STA mode
* AR9344 SoC, AP mode
MFC after: 1 week
This is important in hostap, ibss, (11s at some magical future date, etc)
where different nodes may have smaller limits.
Oops!
MFC after: 1 week
Relnotes: Yes
This adds a workaround to incorrectly behaving APs (ie, FreeBSD APs) which
don't beacon out exactly when they should (at TBTT multiples of beacon
intervals.)
It forces the hardware awake (but leaves it in network-sleep so self
generated frames still state that the hardware is asleep!) and will
remain awake until the next sleep transition driven by net80211.
That way if the beacons are just at the wrong interval, we get a much
better chance of hearing more consecutive beacons before we go to sleep,
thus not constantly disconnecting.
Tested:
* AR9485, STA mode, against a misbehaving FreeBSD AP.
