o Move the sysctls under debug.psm.* and hw.psm.* making them a bit
clearer and more consistent with other drivers.
o Remove the debug.psm_soft_timeout sysctl. It was introduced many
moons ago in r1.64 but never referenced anywhere.
o Introduce hw.psm.tap_threshold and hw.psm.tap_timeout to control
the behaviour of taps on touchpads. People might like to fiddle
with these if tapping seems to slow or too fast for them.
o Add debug.psm.loglevel as a tunable so that verbosity can be set
easily at boot-time (to watch probes and such) without having to
compile a kernel with options PSM_DEBUG=N.
These devices should be probed first because they are at fixed
locations and cannot be turned off. ISA PNP devices, on the other
hand, can be turned off and often can be flexible in the resources
they use. Probe them last, as always.
people have reported problems (stickyness, aiming difficulty) which is proving
difficult to fix, so this will default to disable until sometime after 5.3R.
To enable Synaptics support, set the 'hw.psm.synaptics_support=1' tunable.
MT5 candidate.
Approved by: njl
because it was mostly irrelevant - except for the silly BIOS_PADDRTOVADDR
etc macros. Along the way of working around this, I missed a few things.
* Make syscons properly inherit the bios capslock/shiftlock/etc state like
i386 does. Note that we cannot inherit the bios key repeat rate because
that requires a bios call (which is impossible for us).
* Give syscons the ability to beep on amd64. Oops.
While here, make bios.c compile and add it to files.amd64.
and which takes a M_WAITOK/M_NOWAIT flag argument.
Add compatibility isa_dmainit() macro which whines loudly if
isa_dma_init() fails.
Problem uncovered by: tegge
o Remove PSM_SYNCERR_THRESHOLD1. This value specified how many sync
errors were required before the mouse is re-initialised.
Re-initialisation is now done after (packetsize * 2) sync errors as
things aren't likely to improve after that.
o Reset lastinputerror when re-initialisation occurs. We don't want
to continue to drop data after re-initialisation.
o Count the number of failed packets independently of the syncerrors
statistic. syncerrors is useful for recovering sync within a single
packet. pkterrors allows us to detect when the mouse changes its
packet mode due to some external event (e.g. KVM switch).
o Reinitialize the mouse if we see more than psmpkterrthresh errors
during the validation period. The validation period begins as soon
as a sync error is detected and continues until psmerrsecs/msecs
time has elapsed. The defaults for these two values force a reset
if we see two packet errors in a 2 second period. This allows rapid
detection of packet framing errors caused by the mouse changing packet
modes.
o Export psmpkterrthresh as a sysctl
o Export psmloglevel as a sysctl.
o Enable more debugging code to be enabled at runtime via psmloglevel.
o Simplify verbose conditioned loging by using a VLOG macro.
o Add several comments describing the sync recovery algorithm of
this driver.
Large Portions by: Brian Somers <brian@Awfulhak.org>
Inspired and Frustrated by: Belkin KVMs
Reviewed by: njl, philip
data packet is received from the mouse. In the case of many KVM's,
this avoids a bug in their mouse emulation that sends back incorrect
sync when you explicitly request a data packet from the mouse. Without
this change, you must force the driver into stock PS/2 mode or be flooded
with a never ending stream of "out of sync" messages on these KVMs.
Approved by: re
o Change the motion calculation to result in
a more reasonable speed of motion
This should fix the 'aiming' problems people have reported. It also
mitigates (but doesn't completely solve) the 'stalling' problems at
very low speeds.
Tested by: many subscribers to -current
Approved by: njl
o Catch 'taps' as button presses
o One finger sends button1, two fingers send button3,
three fingers send button2 (double-click)
Tested by: many subscribers to -current
Approved by: njl
o Handle the 'up/down' buttons some touchpads have as
a z-axis (scrollwheel) as recommended by the specs
o Report the buttons as button4 and button5 instead
of button2 and button4, button2 can be emulated by
pressing button1 and button3 simultaneously. This
allows one to use the two extra buttons for other
purposes if one so desires.
Tested by: many subscribers to -current
Approved by: njl
o Clean up whitespace and comments in the
enable_synaptics() probing function
o Only use (and rely on) the extended capability
bits when we are told they actually exist
o Partly ignore the (possibly dated?) part of the
specification about the mode byte so that we
can support 'guest devices' too.
Tested by: many subscribers to -current
Approved by: njl
submitted version with style cleanups and changes to comments. I also
modified the ioctl interface. This version only has one ioctl (to get
the Synaptics-specific config parameters) since this is the only
information a user might want.
Submitted by: Arne Schwabe <arne -at- rfc2549.org>
a problem that could also be fixed differently without reverting previous
attempts to fix DELAY while the debugger is active (rev 1.204). The bug
was that the i8254 implements a countdown timer, while for (k)db_active
a countup timer was implemented. This resulted in premature termination
and consequently the breakage of DELAY. The fix (relative to rev 1.211)
is to implement a countdown timer for the kdb_active case. As such the
ability to step clock initialization is preserved and DELAY does what is
expected of it.
Blushed: bde :-)
Submitted by: bde
debugger is not active. The fixes breakages of DELAY() when
running in the debugger, because not calling getit() when the
debugger is active yields a DELAY that doesn't.
repocopied. Soon there will be additional bus attachments and
specialization for isa, acpi and pccard (and maybe pc98's cbus).
This was approved by nate, joerg and myself. bde dissented on the new
location, but appeared to be OK after some discussion.
correct interrupt source.
- Cache a pointer to the i8254_intsrc's pending method to avoid several
pointer indirections in i8254_get_timecount().
Reported by: bde
scenario into #ifdef DEBUG. This makes my cluster with Belkin
KVM switch completely usable, even if the KVM switch and mouse
get a bit confused sometimes.
Without this, when the mouse gets confused, all sorts of crud
gets spammed all over the screen. With this, the mouse may appear
dead for a second or three, but it recovers silently.
Introduce d_version field in struct cdevsw, this must always be
initialized to D_VERSION.
Flip sense of D_NOGIANT flag to D_NEEDGIANT, this involves removing
four D_NOGIANT flags and adding 145 D_NEEDGIANT flags.
Free approx 86 major numbers with a mostly automatically generated patch.
A number of strategic drivers have been left behind by caution, and a few
because they still (ab)use their major number.
resources. (Note that the correct range is 0x3f7,0x3f0-0x3f5.) Such
devices will be detected as follows:
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port
0x3f7,0x3f4-0x3f5,0x3f2-0x3f3,0x3f0-0x3f1 irq 6 drq 2 on acpi0
To do this, we find the minimum and maximum start addresses for the
resources and use them as the base for the IO and control ports.
Help from: jhb
when using a KVM.
There is no actual solution possible, but this gets us pretty close.
Typically when switching back to a FreeBSD box and moving the mouse
wild data is produced, because the protocol's validation/checksum
system is extremely weak it is impossible to determine that we're
out of sync before dropping several bogus packets to user land.
The actual solution that appears to offer the best clamping of
jitter is to buffer the mouse packets if we've not seen mouse
activity for more than .5 seconds. Then waiting to flush that data
for 1/20th of a second. If within that 20th of a second we get any
packets that do fail the weak test we drop the entire queue and
back off accepting data from the mouse for 2 seconds and then repeat
the whole deal.
You can still get _some_ jitter, notably if you switch to the FreeBSD
box, then move the mouse just enough to generate one or two packets.
Those packets may be bogus, but may still pass the validity check.
One way to finally kill the problem once and for all is to check
the initial packets for "wild" values. Typically one sees packets
in the +/-60 range during normal operation, however when bogus data
is generated it's typically near the outer range of +/-120 or more,
those packets would be a good candidate for dropping or clamping.
I've been running with this for several weeks now and it has
significantly helped me stay sane even with a piece of junk Belkin
KVM causing wild jitter each and every time I switch.
Lastly I'd like to note that my experience with Windows shows me that
somehow the Microsoft PS/2 driver typically avoids this problem, but
that may only be possible when running the mouse in a dumb-ed down PS/2
mode that Belkin recommends on their site.
thread being waken up. The thread waken up can run at a priority as
high as after tsleep().
- Replace selwakeup()s with selwakeuppri()s and pass appropriate
priorities.
- Add cv_broadcastpri() which raises the priority of the broadcast
threads. Used by selwakeuppri() if collision occurs.
Not objected in: -arch, -current
- The apic interrupt entry points have been rewritten so that each entry
point can serve 32 different vectors. When the entry is executed, it
uses one of the 32-bit ISR registers to determine which vector in its
assigned range was triggered. Thus, the apic code can support 159
different interrupt vectors with only 5 entry points.
- We now always to disable the local APIC to work around an errata in
certain PPros and then re-enable it again if we decide to use the APICs
to route interrupts.
- We no longer map IO APICs or local APICs using special page table
entries. Instead, we just use pmap_mapdev(). We also no longer
export the virtual address of the local APIC as a global symbol to
the rest of the system, but only in local_apic.c. To aid this, the
APIC ID of each CPU is exported as a per-CPU variable.
- Interrupt sources are provided for each intpin on each IO APIC.
Currently, each source is given a unique interrupt vector meaning that
PCI interrupts are not shared on most machines with an I/O APIC.
That mapping for interrupt sources to interrupt vectors is up to the
APIC enumerator driver however.
- We no longer probe to see if we need to use mixed mode to route IRQ 0,
instead we always use mixed mode to route IRQ 0 for now. This can be
disabled via the 'NO_MIXED_MODE' kernel option.
- The npx(4) driver now always probes to see if a built-in FPU is present
since this test can now be performed with the new APIC code. However,
an SMP kernel will panic if there is more than one CPU and a built-in
FPU is not found.
- PCI interrupts are now properly routed when using APICs to route
interrupts, so remove the hack to psuedo-route interrupts when the
intpin register was read.
- The apic.h header was moved to apicreg.h and a new apicvar.h header
that declares the APIs used by the new APIC code was added.
