The ring logic of the NTB receive buffer/transmit memory window requires
there to be at least 2 payload sized allotments. For the minimal size
case, split the buffer into two and set the transport_mtu to the
appropriate size.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
If the NTB link toggles, the driver could stop receiving due to the
tx_index not being set to 0 on the transmitting size on a link-up event.
This is due to the driver expecting the incoming data to start at the
beginning of the receive buffer and not at a random place.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
Each link-up will allocate a new NTB receive buffer when the NTB
properties are negotiated with the remote system. These allocations did
not check for existing buffers and thus did not free them. Now, the
driver will check for an existing buffer and free it if not of the
correct size, before trying to alloc a new one.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
64bit BAR sizes are permissible with an NTB device. To support them
various modifications and clean-ups were required, most significantly
using 2 32bit scratch pad registers for each BAR.
Also, modify the driver to allow more than 2 Memory Windows.
Authored by: Jon Mason
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
->remote_rx_info and ->rx_info are struct ntb_rx_info pointers. If we
add sizeof(struct ntb_rx_info) then it goes too far.
Authored by: Dan Carpenter
Obtained from: Linux
Sponsored by: EMC / Isilon Storage Division
This change fixes some amount of -Wsign-conversion and -Wconversion warnings
and sets correct sizes for some variables (as a result, some loop counters
were touched too).
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3763
This is roughly the iw_cxgbe equivalent of
be13b2dff8
-----------------
RDMA/cxgb4: Connect_request_upcall fixes
When processing an MPA Start Request, if the listening endpoint is
DEAD, then abort the connection.
If the IWCM returns an error, then we must abort the connection and
release resources. Also abort_connection() should not post a CLOSE
event, so clean that up too.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
-----------------
Submitted by: Krishnamraju Eraparaju at chelsio dot com.
This was off because the net80211 aggregation code was using the same
state pointers for both fast frames and ampdu tx support which led to some
pretty unfortunate panic-y behaviour.
Now that net80211 doesn't panic, let's flip this back on.
It doesn't (yet) do the horrific sounding thing of A-MPDU aggregates
of fast frames; that'll come next. It's a pre-requisite to supporting
AMSDU + AMPDU anyway, which actually speeds things up quite considerably
(think packing lots of little ACK frames into a single AMSDU.)
Tested:
* QCA955x SoC, AP mode
* AR5416, STA mode
* AR9170, STA mode (with local fast frame patches)
these functions are thin wrappers around calling the hardware-layer driver,
but some of them do sanity checks and return an error. Since the hardware
layer can only return IIC_Exxxxx status values, the iicbus helper functions
must also adhere to that, so that drivers at higher layers can assume that
any non-zero status value is an IIC_Exxxx value that provides details about
what happened at the hardware layer (sometimes those details are important
for certain slave drivers).
errno values that are at least vaguely equivelent. Also add a new status
value, IIC_ERESOURCE, to indicate a failure to acquire memory or other
required resources to complete a transaction.
The IIC_Exxxxxx values are supposed to communicate low-level details of the
i2c transaction status between the lowest-layer hardware driver and
higher-layer bus protocol and device drivers for slave devices on the bus.
Most of those slave drivers just return all status values from the lower
layers directly to their callers, resulting in crazy error reporting from a
user's point of view (things like timeouts being reported as "no such
process"). Now there's a helper function to make it easier to start
cleaning up all those drivers.
Make it clearer what each one means in the comments that define them.
IIC_BUSBSY was used in many places to mean two different things, either
"someone else has reserved the bus so you have to wait until they're done"
or "the signal level on the bus was not in the state I expected before/after
issuing some command".
Now IIC_BUSERR is used consistantly to refer to protocol/signaling errors,
and IIC_BUSBSY refers to ownership/reservation of the bus.
perform a stop operation on the bus if there was an error, otherwise the
bus will remain hung forever. Consistantly use 'if (error != 0)' style in
the function.
The current Xen console driver is crashing very quickly when using it on
an ARM guest. This is because the console lock is recursive and it may
lead to recursion on the tty lock and/or corrupt the ring pointer.
Furthermore, the console lock is not always taken where it should be and has
to be released too early because of the way the console has been designed.
Over the years, code has been modified to support various new features but
the driver has not been reworked.
This new driver has been rewritten with the idea of only having a small set
of specific function to write either via the shared ring or the hypercall
interface.
Note that HVM support has been left aside for now because it requires
additional features which are not yet supported. A follow-up patch will be
sent with HVM guest support.
List of items that may be good to have but not mandatory:
- Avoid to flush for each character written when using the tty
- Support multiple consoles
Submitted by: Julien Grall <julien.grall@citrix.com>
Reviewed by: royger
Differential Revision: https://reviews.freebsd.org/D3698
Sponsored by: Citrix Systems R&D
Use direct dispatch into the destination hardware ring instead of using
a staging queue.
Submitted by: <s3erios@gmail.com>
Differential Revision: https://reviews.freebsd.org/D3757
Pull the latest headers for Xen which allow us to add support for ARM and
use new features in FreeBSD.
This is a verbatim copy of the xen/include/public so every headers which
don't exits anymore in the Xen repositories have been dropped.
Note the interface version hasn't been bumped, it will be done in a
follow-up. Although, it requires fix in the code to get it compiled:
- sys/xen/xen_intr.h: evtchn_port_t is already defined in the headers so
drop it.
- {amd64,i386}/include/intr_machdep.h: NR_EVENT_CHANNELS now depends on
xen/interface/event_channel.h, so include it.
- {amd64,i386}/{amd64,i386}/support.S: It's not neccessary to include
machine/intr_machdep.h. This is also fixing build compilation with the
new headers.
- dev/xen/blkfront/blkfront.c: The typedef for blkif_request_segmenthas
been dropped. So directly use struct blkif_request_segment
Finally, modify xen/interface/xen-compat.h to throw a preprocessing error if
__XEN_INTERFACE_VERSION__ is not set. This is allow us to catch any file
where xen/xen-os.h is not correctly included.
Submitted by: Julien Grall <julien.grall@citrix.com>
Reviewed by: royger
Differential Revision: https://reviews.freebsd.org/D3805
Sponsored by: Citrix Systems R&D
'rdrand' instruction may occasionally not return random numbers, in
spite of looping attempts to do so. The reusult is a KASSERT/panic.
Reluctantly accept this state-of-affairs, but make a noise about it.
if this 'noise' spams the console, it may be time to discontinue
using that source.
This is written in a general way to account for /any/ source that
might not supply random numbers when required.
Submitted by: jkh (report and slightly different fix)
Approved by: so (/dev/random blanket)
* Remove obsolete drm_agp_*_memory() prototypes.
* Fix comment in drm_fops.c (outisde -> outside).
* Fix some formatting issues in drm_stub.c (spaces -> tabs).
* Add missing case statement (gen == 3) in intel_gpu_reset().
* Restore pci_enable_busmaster() call in the init path (fixes gpu hang on i945GM).
* Replace M_WAITOK with M_NOWAIT when the return value of malloc is checked (may be incorrect).
Submitted by: <s3erios@gmail.com>
Reviewed by: dumbbell
Approved by: dumbbell
Differential Revision: https://reviews.freebsd.org/D3413
Now run(4) fetches parameters from ic->ic_wme.wme_params array, which is never initialized
(and can be safely removed). This patch replaces &ic->ic_wme.wme_params with
&ic->ic_wme.wme_chanParams.cap_wmeParams (contains parameters for local station;
used by other drivers with WME support).
Tested:
* me: STA: run0: MAC/BBP RT5390 (rev 0x0502), RF RT5370 (MIMO 1T1R), address 38:83:45:11:78:ae
