The valectl(4) program is used to manage vale(4) switches.
Add it to the system commands so that it can be used right away.
This program was previously called vale-ctl, and stored in
tools/tools/netmap
Reviewed by: hrs, bcr, lwhsu, kevans
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D22146
This is a simple utility to hash all trusted on the system into
/etc/ssl/certs. It also allows the user to blacklist certificates they do
not trust.
This work was done primarily by allanjude@, with minor contributions by
myself.
No objection from: secteam
Differential Revision: https://reviews.freebsd.org/D16857
This avoids PATH conflicts with a real httpd, as a user will likely almost
always prefer the more fully-featured httpd. This also lines up with the
historical name of the program.
picobsd/tinyware has had this compact HTTPD server for a long time, and some
people do use it. Move it out into usr.sbin well in advance of any action
being taken on picobsd.
This has been gated behind an HTTPD option defaulted to *off*, primarily for
two reasons:
1.) This code likely needs a good audit, as it's been living off in picobsd
land for a long time, and
2.) We don't currently ship an httpd and this may not be a welcome surprise.
Reviewed by: eugen
Differential Revision: https://reviews.freebsd.org/D21724
NANDFS has been broken for years. Remove it. The NAND drivers that
remain are for ancient parts that are no longer relevant. They are
polled, have terrible performance and just for ancient arm
hardware. NAND parts have evolved significantly from this early work
and little to none of it would be relevant should someone need to
update to support raw nand. This code has been off by default for
years and has violated the vnode protocol leading to panics since it
was committed.
Numerous posts to arch@ and other locations have found no actual users
for this software.
Relnotes: Yes
No Objection From: arch@
Differential Revision: https://reviews.freebsd.org/D20745
on devices using wear-leveling algorithms as a few weeks passed
after review and discussion of trim(8) ceased and
we still have no utility to perform the job.
Reviewed by: hackers@
MFC after: 2 weeks
The removal (and creation of a port) has been pre-announced in UPDATING
1 month ago. Packages are available for all supported FreeBSD vesions.
I did not think that another entry in UPDATING is required to note the
actual removal.
No MFC is planned - CTM shall be kept in base for all releases up to 12.x.
Reviewed by: rgrimes
Approved by: imp, bcr (manpages)
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D17935
The pwm subsystem consist of API for PWM controllers, pwmbus to register them
and a pwm(8) utility to talk to them from userland.
Reviewed by: oshgobo (capsicum), bcr (manpage), 0mp (manpage)
Differential Revision: https://reviews.freebsd.org/D17938
I had disabled building of the aforementioned targets due to warnings breaking
tinderbox. This silences the warning and restores them to the build.
Reported by: jhibbits
Reviewed by: jhibbits
Approved by: re (gjb)
userland, conceptually similar to what i2c(8) provides for i2c devices.
Submitted by: Bob Frazier
Differential Revision: https://reviews.freebsd.org/D15029
try to build them if MK_OPENSSL is unset.
Reviewed by: emaste imp kevans
Sponsored by: Limelight Networks
Differential Revision: https://reviews.freebsd.org/D15211
This command can be used by a sysadmin to either copy or migrate a data
file on one DS to another DS.
Its main use is to recover data files onto a mirrored DS after the DS has
been repaired and brought back online.
This command allows a sysadmin to display or modify the pnfsd.dsfile extended
attribute used by the pNFS MDS server in various ways.
Its main use is to set a DS's IP address to 0.0.0.0 when that DS has failed,
so that it will not be used for the file when brought back online after
being repaired.
- add '-j' options to filter to enable converting native pmc
log format to json lines format to enable the use of scripts
and external tooling
% pmc filter -j pmc.log pmc.jsonl
- Record the tsc value in sampling interrupts as opposed to
recording nanotime when the sample is copied to a global log
in hardclock - potentially many milliseconds later.
- At initialize record the tsc_freq and the time of day to give
us an offset for translating the tsc values in callchain records
By logging all threads and processes 'pmc filter'
can now filter on process or thread name, relieving
the user of the burden of determining which tid or
pid was which when the sample was taken.
% pmc filter -T if_io_tqg -P nginx pmc.log pmc-iflib.log
% pmc filter -x -T idle pmc.log pmc-noidle.log
This will manage pmc functionality with a more
manageable structure of subcommands rather than the
gradually accreted spaghetti logic of overlapping flags
that exists in pmcstat.
This is intended to ultimately have all the same functionality
as pmcannotate+pmccontrol+pmcstat. Currently it just has
"stat" and "system-stat" - counters for the process itself and counters
for the system as a whole respectively (i.e. system-stat includes kernel
threads). Note that the rusage results (page faults/context switches/
user/sys) for stat-system will not account for the system as a whole -
only for the child process specified on the command line.
Implementing stat was suggested by mjg@ and the output is based on that
from Linux's "perf stat".
% pmc stat -- make -j32 buildkernel -DNO_MODULES -ss > /dev/null
9598393 page faults # 0.674 M/sec
387085 voluntary csw # 0.027 M/sec
106989 involuntary csw # 0.008 M/sec
2763965982317 cycles
2542953049760 instructions # 0.920 inst/cycle
511562750157 branches
12917006881 branch-misses # 2.525%
17944429878 cache-references # 0.007 refs/inst
2205119560 cache-misses # 12.289%
43.74 real # 2019.72% cpu
795.09 user # 1817.72% cpu
88.35 sys # 202.00% cpu
% make -j32 buildkernel -DNO_MODULES -ss > /dev/null &
% sudo pmc stat-system cat
^C 103 page faults # 0.811 M/sec
4 voluntary csw # 0.031 M/sec
0 involuntary csw # 0.000 M/sec
2843639070514 cycles
2606171217438 instructions # 0.916 inst/cycle
522450422783 branches
13092862839 branch-misses # 2.506%
18592101113 cache-references # 0.007 refs/inst
2562878667 cache-misses # 13.785%
44.85 real # 0.00% cpu
0.00 user # 0.00% cpu
0.00 sys # 0.00% cpu
This driver supports legacy, 32-bit PCI devices, and had an ambiguous
license. Supported devices were already reported to be rare in 2003
(when an earlier version of the driver was removed in r123201).
Reviewed by: rgrimes
Relnotes: Yes
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D15245
ConnectX-4/5 devices in mlx5core.
The dump is obtained by reading a predefined register map from the
non-destructive crspace, accessible by the vendor-specific PCIe
capability (VSC). The dump is stored in preallocated kernel memory and
managed by the mlx5tool(8), which communicates with the driver using a
character device node.
The utility allows to store the dump in format
<address> <value>
into a file, to reset the dump content, and to manually initiate the
dump.
A call to mlx5_fwdump() should be added at the places where a dump
must be fetched automatically. The most likely place is right before a
firmware reset request.
Submitted by: kib@
MFC after: 1 week
Sponsored by: Mellanox Technologies
more in r317426. There's nothing in the tree that references digiio.h
(apart from digictl(8)), so no driver implements it. Since digictl(8)
was only used to control digi(4) devices, it too should go.
devmatch(8) matchs up devices in the system device tree with drivers
that may match them. For each unattached device in the system, it
tries to find matching PNP info in the linker hints and prints modules
to load to claim the devices.
In --unbound mode, devmatch can look for drivers that have attached to
devices in the device tree and have plug and play information, but for
which no PNP info exists. This helps find drivers that haven't been
converted yet that are in use on this system.
In addition, the ability to dump out linker.hints is provided.
Future commits will add hooks to devd.conf and rc.d to fully automate
using this information.
efibootmgr manages the UEFI BootXXXX variables that implement the UEFI
Boot Manager protocol defined in the UEFI standards. It is modeled
after the Linux program of the same name with a mostly compatible set
of command line options. Since there's a fair amount of OS specifioc
code due to differeing names and methods of doing things, the
compatibility isn't 100%.
Basic functionality is implemented, though the more advanced next boot
functionality that's been defined elsewhere is unimplemented.
Submitted by: Matt Williams (with unix / efi path xlate by me)
Sponsored by: Netflix
It was supposed to provide a recovery mechanism against bugs in procfs's
long deprecated tracing capabilities.
Remove the tool as a prerequisite to axing the kernel side.
The tracing facility to use is ptrace(2).
MFC after: 2 weeks
As peter@ points out in pr/220953:
"rwho, rwhod and ruptime are not part of the remote login suite (rsh, rlogin
etc).
They should *not* be in the rcmds package which is disabled by default. We
rely on rwho/rwhod/ruptime in the freebsd.org cluster."
This commit is a re-commit of r322029 and r322031 with a better commit log, as
pointed out by ngie@.
This also includes the necesary changes to OptionalObsoleteFiles.inc, as
requested by jhb@.
PR: 220953
Reported by: peter@, jhb@
Differential Revision: https://reviews.freebsd.org/D11743
After the addition of SUBDIR.yes, uniquifying/ordering the SUBDIRs doesn't
make a whole lot of sense, and it's in effect a half measure.
Ordering SUBDIR (after adding SUBDIR.yes to it) in bsd.subdir.mk is a
separate change that warrants more discussion/testing, because while
the SUBDIR_PARALLEL work largely fixed dependency ordering for SUBDIRs,
there might be downstream FreeBSD consumers that rely on the SUBDIR
ordering.
MFC after: 2 months
Reviewed by: bdrewery
Differential Revision: D11398
formats and parses UEFI standard Device Paths. In the future it will
also translate between FreeBSD driver names and UEFI Device Paths.
Sponsored by: Netflix
Move cxgbetool from tools/tools to usr.sbin. Compile and install it on
platforms where cxgbe(4) is built by default. Knobs (WITH_CXGBETOOL and
WITHOUT_CXGBETOOL) have been added so that the user can override the
default setting.
Reviewed by: ngie@, gnn@, bdrewery@
MFC after: 1 month
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D9854
Now that we have our sysctl tree annotated with aggregation labels,
let's go ahead and provide a very simple utility for exporting the
sysctl tree in Prometheus' format. It can either be used in conjunction
with the Prometheus node exporter or run through inetd(8).
The reason why I'm opting for having it in the base system is because it
has a pretty strong integration with some of sysctl's innards, such as
access to iterators, name lookups, metadata and type information. As I
am investigating whether we can add histograms as native types to sysctl
as well, this integration will only get stronger as we go along. That's
why it would be safer to oversee the development of this exporter
ourselves, as opposed to having it as an external project.
This exporter is remarkably compact, especially when compared to the
official Linux binary of the Prometheus node exporter (16 KB vs 12 MB).
I guess this could be an interesting aspect for monitoring embedded
FreeBSD-based systems.
Differential Revision: https://reviews.freebsd.org/D8792
Hide dialog specific code behind HAVE_DIALOG. It allows to build a stripped
down version (missing the dialog UI) but perfectly function tzsetup when
world is built WITHOUT_DIALOG
Reorganise a bit the code to limit the number of blocks under HAVE_DIALOG
Reviewed by: emaste
Sponsored by: https://reviews.freebsd.org/D8325
with no creative content. Include "lost" changes from git:
o Use /dev/efi instead of /dev/efidev
o Remove redundant NULL checks.
Submitted by: kib@, dim@, zbb@, emaste@
line interface to the Linux program, as well as adding a number of
useful features to make using it in shell scripts easier (since we
don't have a filesystem to fall back on interacting with).
Differential Revision: https://reviews.freebsd.org/D8128
Reviewed by: kib@, wblock@, Ganael Laplanche
It also turns off dependencies (bsdinstall, bsdconfig, dpv, tzsetup).
Reviewed by: dteske
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D7969
