lcall 7,0 (ie: ldt slot 0) and lcall 0x87,0 (ldt slot 16, it's shifted
three bits to the left). I was fiddling with this so long ago, I don't
recall the specifics.
with this quite a while ago when somebody reported a BSD/OS 2.1 binary
that wouldn't run. I'm pretty sure they tried it and I'm pretty sure
they mentioned to me that the patch worked.
comparisons in the inb() and outb() macros. I decided that int args
are OK here. Any type that can hold a u_int16_t without overflow
is correct, and 32-bit types are optimal.
Introduced a few tens of warnings (100 in LINT) for use of pessimized
(short) types for the port arg. Only a few drivers are affected by
this. u_short pessimizations aren't detected.
Added `__extension__' before the statement-expression in inb() so
that it can be compiled without warnings by gcc -pedantic.
the prototype.
Put the jump table for i486_bzero() in the data section. This
speeds up i486_bzero() a little on Pentiums without significantly
affecting its speed on 486's.
Don't waste time falling through 14 nop's to return from do1 in
i486_bzero().
Use fastmove() for counts >= 1024 (was > 1024). Cosmetic.
Fixed profiling of fastmove().
Restored meaningful labels from the pre-1.1 version in fastmove().
Local labels are evil.
Fixed (high resolution non-) profiling of __bb_init_func().
I maintain that it saves more power to simply "hlt" the CPU than to
spend tons of time trying to tell the APM bios to do the same.
In particular if you do it 100 times a second...
instead of 0 if there is no input.
syscons.c:
Added missing spl locking in sccncheckc(). Return the same value as
sccngetc() would. It is wrong for sccngetc() to return non-ASCII, but
stripping the non-ASCII bits doesn't help.
(1) Add PC98 support to apm_bios.h and ns16550.h, remove pc98/pc98/ic
(2) Move PC98 specific code out of cpufunc.h (to pc98.h)
(3) Let the boot subtrees look more alike
Submitted by: The FreeBSD(98) Development Team
<freebsd98-hackers@jp.freebsd.org>
modified. Pages that are removed by the pageout daemon were
the worst affected. Additionally, numerous minor cleanups,
including better handling of busy page table pages. This
commit fixes the worst of the pmap problems recently introduced.
biosextmem > 65536, but biosextmem is a 16-bit quantity so it is
guaranteed to be < 65536. Related cruft for biosbasemem was
mostly cleaned up in rev.1.26.
The default level works with minimal overhead, but one can also enable
full, efficient use of a 512K cache. (Parameters can be generated
to support arbitrary cache sizes also.)
returned by the RTC, use the bootblock supplied value. Also, map the
'stolen by BIOS' memory in the same manner as the ISA-hole memory, since
it is really an extenstion of the BIOS. This is necessary for 32-bit
BIOS functions such as APM support on laptops, and the loss of memory
for non-necessary functions seems to be at most 4k.
Reviewed by: phk
Obtained from: email conversation with jtk@atria.com
nearest .01 Mhz rather than simply truncating it downwards.
This hack makes this 89.999928 Mhz clock correctly round to the closer
90.00-MHz rather than 89.99-MHz:
> i586 clock: 89999928 Hz, i8254 clock: 1193152 Hz
> CPU: Pentium (90.00-MHz 586-class CPU)
Changed i586_ctr_bias from long long to u_int. Only the low 32 bits
are used now that microtime uses a multiplication to do the scaling.
Previously the high 32 bits had to match those of rdtsc() to prevent
overflow traps and invalid timeval adjustments.
early enough when the dump device is specified in the config file.
Removed stale comment about configuration root and swap devices.
Don't bother clearing dumplo when dumpdev is set to NODEV. Everything
is controlled by dumpdev.
Fixed the kern.dumpdev sysctl. Writes were handle bogusly.
problem with the 'shell scripts' was found, but there was a 'strange'
problem found with a 486 laptop that we could not find. This commit
backs the code back to 25-jul, and will be re-entered after the snapshot
in smaller (more easily tested) chunks.
performance issues.
1) The pmap module has had too many inlines, and so the
object file is simply bigger than it needs to be.
Some common code is also merged into subroutines.
2) Removal of some *evil* PHYS_TO_VM_PAGE macro calls.
Unfortunately, a few have needed to be added also.
The removal caused the need for more vm_page_lookups.
I added lookup hints to minimize the need for the
page table lookup operations.
3) Removal of some bogus performance improvements, that
mostly made the code more complex (tracking individual
page table page updates unnecessarily). Those improvements
actually hurt 386 processors perf (not that people who
worry about perf use 386 processors anymore :-)).
4) Changed pv queue manipulations/structures to be TAILQ's.
5) The pv queue code has had some performance problems since
day one. Some significant scalability issues are resolved
by threading the pv entries from the pmap AND the physical
address instead of just the physical address. This makes
certain pmap operations run much faster. This does
not affect most micro-benchmarks, but should help loaded system
performance *significantly*. DG helped and came up with most
of the solution for this one.
6) Most if not all pmap bit operations follow the pattern:
pmap_test_bit();
pmap_clear_bit();
That made for twice the necessary pv list traversal. The
pmap interface now supports only pmap_tc_bit type operations:
pmap_[test/clear]_modified, pmap_[test/clear]_referenced.
Additionally, the modified routine now takes a vm_page_t arg
instead of a phys address. This eliminates a PHYS_TO_VM_PAGE
operation.
7) Several rewrites of routines that contain redundant code to
use common routines, so that there is a greater likelihood of
keeping the cache footprint smaller.
