. Make internal service routines static.
. Use a consistent ordering of checks in MII_TICK. Do the work in the
mii_phy_tick() subroutine if appropriate.
. Call mii_phy_update() to trigger the callbacks.
ethernet controllers. This adds support for the 3Com 3c996-T, the
SysKonnect SK-9D21 and SK-9D41, and the built-in gigE NICs on
Dell PowerEdge 2550 servers. The latter configuration hauls ass:
preliminary measurements show TCP speeds of over 900Mbps using
only normal size frames.
TCP/IP checksum offload, jumbo frames and VLAN tag insertion/stripping
are supported, as well as interrupt moderation.
Still need to fix autonegotiation support for 1000baseSX NICs, but
beyond that, driver is pretty solid.
sio_lock has been initialized. This prevents the low level console
output (kernel printf) from clobbering the sio settings if the system
happens to be in the middle of comstart().
with weird PCI-PCI bridge configurations to work. Defining
PCI_ALLOW_UNSUPPORTED_IO_RANGE causes the sanity checks to pass even
with out of range values.
Reviewed by: msmith
This fixed the problem on the 3 platforms I've been able to test on.
I'm still of the oppinion that the BIOS should take care of this,
however some board makers only apply this when they spot a
SBLive! soundcard, but the problem exists even without a SBLive!.
This fix should probably go somewhere else, but for now I'll
keep it here since we havn't got a central place to put
such things.
problems currently experienced in -CURRENT.
This should fix the problem that the PS/2 mouse is detected
twice if the acpi module is not loaded on some systems.
we're at least consistent with what tcsendbreak(3) is documented
to do.
MFC after: 2 weeks
Note, the MFC will be to sys/dev/dgb/dgm.c on the RELENG_4 branch
I am not sure if this is absolutely necessary on all systems. Yet,
there certainly are motherboards and notebook systems which require
this, although there are other systems which just don't. I hope we
shall know when to do this on which systems, as the development of our
ACPI subsystem progresses... (I know we didn't need this for the APM
resume.)
ppc to go into EPP mode. These 8 inputs are timestamped in polled
loop so their resolution will be nanoseconds but their granularity
will only be 1/hz.
- SC_CUT_SPACES2TABS - when copying text into the cut buffer convert leading
spaces into the tabs;
- SC_CUT_SEPCHARS="XYZ" - treat supplied characters as possible words
separators when the driver searches for words boundaries when doing cut
operation.
Also unify cut code a bit to decrease amount of duplicated code. This fixes
line cut mode, so that it is no longer pads line with useless spaces.
Approved by: ru
seems to set up memory spaces correctly. This change actually did work for
me using -STABLE, XFree86 4.0.3 ~ some snapshot of DRI awhile back. I sent
mail to dfr to no avail, perhaps someone else would like to test it with
DRI.
Anyway, people have been nagging me about this change for awhile, so here's
the commit.
of the rxeoc handler for now. The rxeoc handler will reset the link,
and the NatSemi chip's RX FIFO will overflow on a 32-bit bus once you
start hitting it with 500Mbps or more of traffic.
Also increase the size of the RX ring to 128 descriptors (was 64).
amdpm(4) and smb(4).
This device can be used with userland programs such as sysutils/lmmon
to retrieve sensor information from the motherboard.
PR: kern/23989
Obtained from: Matthew C. Forman <mcf@dmu.ac.uk>
Based on: alpm(4)
- Add workaround for the problematic PnP BIOS which does not assign
irq resource for the PS/2 mouse device node; if there is no irq
assigned for the PS/2 mouse node, refer to device.hints for an
irq number. If we still don't find an irq number in the hints
database, use a hard-coded value.
- Delete unused ivars.
- Bit of clean up in probe/attach.
- Add PnP ID for the PS/2 mouse port on some IBM ThinkPad models.
them if the device arrives.
This should solve the problem where devices that have been disabled eg. in
the BIOS show up with nonsense resources and hang the bootstrap process.
no longer possible to unload the driver module while sound is playing
(which resulted in a panic).
- Fix a similar problem with the sndstat device that I found while looking
at the above.
- Append a newline character to error messages in pcm_unregister()
Reviewed by: cg
MFC after: 10 days
Note ALL MODULES MUST BE RECOMPILED
make the kernel aware that there are smaller units of scheduling than the
process. (but only allow one thread per process at this time).
This is functionally equivalent to teh previousl -current except
that there is a thread associated with each process.
Sorry john! (your next MFC will be a doosie!)
Reviewed by: peter@freebsd.org, dillon@freebsd.org
X-MFC after: ha ha ha ha
