reality. There will be a new call interface, but for now the file
pci_compat.c (which is to be deleted, after all drivers are converted)
provides an emulation of the old PCI bus driver functions. The only
change that might be visible to drivers is, that the type pcici_t
(which had been meant to be just a handle, whose exact definition
should not be relied on), has been converted into a pcicfgregs* .
The Tekram AMD SCSI driver bogusly relied on the definition of pcici_t
and has been converted to just call the PCI drivers functions to access
configuration space register, instead of inventing its own ...
This code is by no means complete, but assumed to be fully operational,
and brings the official code base more in line with my development code.
A new generic device descriptor data type has to be agreed on. The PCI
code will then use that data type to provide new functionality:
1) userconfig support
2) "wired" PCI devices
3) conflicts checking against ISA/EISA
4) maps will depend on the command register enable bits
5) PCI to Anything bridges can be defined as devices,
and are probed like any "standard" PCI device.
The following features are currently missing, but will be added back,
soon:
1) unknown device probe message
2) suppression of "mirrored" devices caused by ancient, broken chip-sets
This code relies on generic shared interrupt support just commited to
kern_intr.c (plus the modifications of isa.c and isa_device.h).
This will make a number of things easier in the future, as well as (finally!)
avoiding the Id-smashing problem which has plagued developers for so long.
Boy, I'm glad we're not using sup anymore. This update would have been
insane otherwise.
(1) deleted #if 0
pc98/pc98/mse.c
(2) hold per-unit I/O ports in ed_softc
pc98/pc98/if_ed.c
pc98/pc98/if_ed98.h
(3) merge more files by segregating changes into headers.
new file (moved from pc98/pc98):
i386/isa/aic_98.h
deleted:
well, it's already in the commit message so I won't repeat the
long list here ;)
Submitted by: The FreeBSD(98) Development Team
is only used by the icu support modules and by a few drivers that know
too much about the icu (most only use it to convert `n' to `IRQn'). isa.h
is only used by ioconf.c and by a few drivers that know too much about
isa addresses (a few have to, because config is deficient).
#includes to get prototypes.
pci now uses a different interrupt handler type for interrupts that it
dispatches and the isa interrupt handler type for the interrupts that
it handles.
accesses after the BIOS bus scan. The previous revision made the assumption,
that every PCI motherboard did ...
Change the test on the initial value of the CONF1_ADDR_PORT register in a way
that makes the probe succeed on triton based motherboards, without breaking
the EISA motherboard that has some non-PCI register at the same address.
Require the state of the configuration enable bits to be OFF assuming
that the BIOS left them that way, as it should anyway to avoid bad things
to happen.
The tests themselves are copied from the previous release, with the
exception of CONF1_ENABLE_MSK1 having the LSB set. This bit should be
read back as '0', since only DWORD addresses are legal.
Changes relative to 1.12:
- Put extra instruction between outl()/inl() sequence to prevent the
old value being read back because of the bus capacitance.
- Additional check for existence of register at CONF2_ENABLE_PORT.
there is a PCI bus at all) ...
- Do not expect the chip sets to follow even very clearly expressed
requirements of the PCI 2.0 spec.
- Do not read back the value just written to an I/O port without making
sure that some other data have crossed the bus in between ...
fail on new hardware (Compaq Prolinea and Compaq Prosignea), and that
doesn't erroneously identify old mech. 2 chip sets as using mech. 1.
(See section 3.6.4.1.1 of the PCI bus specs rev. 2.0)
