just two different attachments (EISA and PCI) to a single driver.
- Add real locking. Previously these drivers only acquired their lock
in their interrupt handler or in the ioctl routine (but too broadly in
the latter). No locking was used for the stack calling down into the
driver via if_init() or if_start(), for device shutdown or detach. Also,
the interrupt handler held the driver lock while calling if_input(). All
this stuff should be fixed in the locking changes.
- Really fix these drivers to handle if_alloc(). The front-end attachments
were using if_initname() before the ifnet was allocated. Fix this by
moving some of the duplicated logic from each driver into pdq_ifattach().
While here, make pdq_ifattach() return an error so that the driver just
fails to attach if if_alloc() fails rather than panic'ing. Also, defer
freeing the ifnet until the driver has stopped using it during detach.
- Add a new private timer to drive the watchdog timer.
- Pass the softc pointer to the interrupt handlers instead of the device_t
so we can avoid the use of device_get_softc() and to better match what
other drivers do.
auto-negotiation. To make this simpler and easier to understand I have
split this out into two separate timers. One just manages the auto-neg
side of things and one is a transmit watchdog. Neither uses if_watchdog.
- Call ether_ifdetach() at the start of detach.
- Add a missing callout_drain() to detach.
- Hook into the stats timer and use that to drive the transmit watchdog
instead of using if_watchdog.
- Run the stats timer every second to match other drivers instead of every
other second.
- Remove dubious callout handling that stopped the timer only to start it
again while holding the driver lock without dropping it in between the
stop and the start.
Don't allow joins w/o source on an existing group.
This is almost always pilot error.
We don't need to check for group filter UNDEFINED state at t1,
because we only ever allocate filters with their groups, so we
unconditionally reject such calls with EINVAL.
Trying to change the active filter mode w/o going through IPV6_MSFILTER
is also disallowed.
MFC after: 1 day
Tighten input checking in in6p_join_group():
* Don't try to use the source address, when its family is unspecified.
* If we get a join without a source, on an existing inclusive
mode group, this is an error, as it would change the filter mode.
Fix a problem with the handling of in6_mfilter for new memberships:
* Do not rely on im6f being NULL; it is explicitly initialized to a
non-NULL pointer when constructing a membership.
* Explicitly initialize *im6f to EX mode when the source address
is unspecified.
This fixes a problem with in_mfilter slot recycling in the join path.
MFC after: 1 day
Fix an obvious logic error in the IPv4 multicast leave processing,
where the filter mode vector was not updated correctly after the leave.
MFC after: 1 day
the generated binary and remove page size limitation for userland.
- Use contigmalloc(9)/contigfree(9) instead of malloc(9)/free(9) to make
sure the generated binary aligns properly and make it physically contiguous.
pages.
(Note: Claims made in the comments about the handling of breakpoints in
wired pages have been false for roughly a decade. This and another bug
involving breakpoints will be fixed in coming changes.)
Reviewed by: kib
to the set actually restored by tl0_ret() instead of using the whole
trapframe. Additionally skip %g7 as that register is used as the
userland TLS pointer.
PR: 140523
MFC after: 1 week
reliable on some Marvell PHYs. If msk(4) know it still does not
have established link check whether msk(4) missed the link state
change by looking into polled link state.
Reported by: Mel Flynn < mel.flynn+fbsd.current <> mailing.thruhere dot net >,
Gleb Kurtsou <gleb.kurtsou <> gmail dot com >
Tested by: Gleb Kurtsou <gleb.kurtsou <> gmail dot com >
the transmit watchdog. These drivers already used a private timer when
compiled to use Netgraph. This change just makes them always use the
private timer. Note that these drivers do not compile and are disconnected
from the build due to TTY changes.
if_watchdog and if_timer. The driver already contained an optional stats
timer that individual attachments could use to provide a 'tick' event. The
stats timer only ran if the tick function pointer was non-NULL and the
attachment's tick routine had to call callout_reset(), etc. Now the driver
always schedules a stat timer and manages the callout_reset() internally.
This timer is used to drive the watchdog and will also call the attachment's
'tick' handler if one is provided.
Tested by: WATANABE Kazuhiro
to fail due to lack of resources to queue siginfo. Add KSI_SIGQ flag
that allows sigqueue_add() to fail while trying to allocate memory for
new siginfo. When the flag is not set, behaviour is the same as for
KSI_TRAP: if memory cannot be allocated, set bit in sq_kill. KSI_TRAP is
kept to preserve KBI.
Add SI_KERNEL si_code, to be used in siginfo.si_code when signal is
generated by kernel. Deliver siginfo when signal is generated by kill(2)
family of syscalls (SI_USER with properly filled si_uid and si_pid), or
by kernel (SI_KERNEL, mostly job control or SIGIO). Since KSI_SIGQ flag
is not set for the ksi, low memory condition cause old behaviour.
Keep psignal(9) KBI intact, but modify it to generate SI_KERNEL
si_code. Pgsignal(9) and gsignal(9) now take ksi explicitely. Add
pksignal(9) that behaves like psignal but takes ksi, and ddb kill
command implemented as pksignal(..., ksi = NULL) to not do allocation
while in debugger.
While there, remove some register specifiers and use ANSI C prototypes.
Reviewed by: davidxu
MFC after: 1 month
and Marvell handled. Instead of trying to attach two different drivers to
single device, wrapping each call, make one of them (atajmicron, atamarvell)
attach do device solely, but create child device for AHCI driver,
passing it all required resources. It is quite easy, as none of
resources are shared, except IRQ.
As result, it:
- makes drivers operation more independent and straitforward,
- allows to use new ahci(4) driver with such devices, adding support for
new features, such as PMP and NCQ, same time keeping legacy PATA support,
- will allow to just drop old ataahci driver, when it's time come.
