o don't strip the Ethernet header from inbound packets; pass packets
up the stack intact (required significant changes to some drivers)
o reference common definitions in net/ethernet.h (e.g. ETHER_ALIGN)
o track ether_ifattach/ether_ifdetach API changes
o track bpf changes (use BPF_TAP and BPF_MTAP)
o track vlan changes (ifnet capabilities, revised processing scheme, etc.)
o use if_input to pass packets "up"
o call ether_ioctl for default handling of ioctls
Reviewed by: many
Approved by: re
if_cuereg.h (1.5), if_kue.c (1.11), if_kuereg.h (1.5)
date: 2000/03/02 12:37:51; author: augustss;
Use ratecheck() to limit error messages on disconnect.
Break out some common functionality.
most cases NULL is passed, but in some cases such as network driver locks
(which use the MTX_NETWORK_LOCK macro) and UMA zone locks, a name is used.
Tested on: i386, alpha, sparc64
Actually this porting supports Pegasus II chip so I guess some other
devices supported by NetBSD also work. But the devices list are not
included because I cannot confirm if they work.
Obtained from: NetBSD
MFC after: 3 weeks
All calls to mtx_init() for mutexes that recurse must now include
the MTX_RECURSE bit in the flag argument variable. This change is in
preparation for an upcoming (further) mutex API cleanup.
The witness code will call panic() if a lock is found to recurse but
the MTX_RECURSE bit was not set during the lock's initialization.
The old MTX_RECURSE "state" bit (in mtx_lock) has been renamed to
MTX_RECURSED, which is more appropriate given its meaning.
The following locks have been made "recursive," thus far:
eventhandler, Giant, callout, sched_lock, possibly some others declared
in the architecture-specific code, all of the network card driver locks
in pci/, as well as some other locks in dev/ stuff that I've found to
be recursive.
Reviewed by: jhb
multicast filter on the Pegasus chip. Since IPv6 depends a lot
on multicasting, this caused several failures for people trying to
use IPv6 with Pegasus USB ethernet devices.
Submitted by: Jun Kuriyama <kuriyama@FreeBSD.org>
usb_ethersubr.c. This module maintains two queues for packets which
are each protected with one mutex. These are all the changes I can
do for now. Removing the USBD_NO_TSLEEP flag doesn't work yet: when
I tried it, the system would usually freeze up after a NIC had been
operating for a while. The usb_ethersubr module itself ought to
go away; this is the next thing I need to test.
attached by the pnaphy driver. This seems to work fine with my sample
ADMtek adapter (which has both 10/100 ethernet and homePNA connectors
and hardware).
ether_ifdetach().
The former consolidates the operations of if_attach(), ng_ether_attach(),
and bpfattach(). The latter consolidates the corresponding detach operations.
Reviewed by: julian, freebsd-net
Note that if_aue doesn't strictly depend on usb because it uses the
method interface for calls rather than using internal symbols, and
because it's a child driver of usb and therefore will not try and do
anything unless the parent usb code is loaded at some point. if_aue does
strictly depend on miibus as it will fail to link if it is missing.
contains the ADMtek Pegasus AN986 USB chipset. The
adapter supports both 10BaseT and 100BaseT (including
full-duplex). The product code for these adapters is
0x2206.
uhci_check_intr() routine needs to be more careful about deciding when
the end of a transfer has been detected.
This allows me to remove the nasty workaround code from if_aue and if_cue.
Receive performance is now much better for these adapters (500KB/sec
vs. 350KB/sec).
Also removed unused KUE_CUTOFF define from if_kuereg.h.
Submitted by: Lennart Augustsson
Reviewed by: n_hibma
- Sync ohci, uhci and usbdi modules with NetBSD in order to obtain the
following improvements:
o New USBD_NO_TSLEEP flag can be used in place of UQ_NO_TSLEEP
quirk. This allows drivers to specify busy waiting only for
certain transfers (namely control transfers for reading/writing
registers and stuff).
o New USBD_FORCE_SHORT_XFER flag can be used to deal with
devices like the ADMtek Pegasus that sense the end of bulk OUT
transfers in a special way (if a transfer is exactly a multiple
of 64 bytes in size, you need to send an extra empty packet
to terminate the transfer).
o usbd_open_pipe_intr() now accepts an interval argument which
can be used to change the rate at which the interrupt callback
routine is invoked. Specifying USBD_DEFAULT_INTERVAL uses the
value specified in the device's config data, but drivers can
override it if needed.
- Change if_aue to use USBD_FORCE_SHORT_XFER for packet transmissions.
- Change if_aue, if_kue and if_cue to use USBD_NO_TSLEEP for all
control transfers. We no longer force the non-tsleep hack for
bulk transfers since these are done asynchronously anyway.
- Removed quirk entry fiddling from if_aue and if_kue since we don't
need it anymore now that we have the USBD_NO_TSLEEP flag.
- Tweak ulpt, uhid, ums and ukbd drivers to use the new arg to
usbd_open_pipe_intr().
- Add a flag to the softc struct in the ethernet drivers to indicate
when a device has been detached, and use this flag to perform
tests to prevent the drivers from trying to do control transfers
if this is the case. This is necessary because calling if_detach()
with INET6 enabled will eventually result in a call to the driver's
ioctl() routine to delete the multicast groups on the interface,
which will result in attempts to perform control transfers. (It's
possible this also happens even without INET6 support enabled.) This
is pointless since we know that if the detach method has been called,
the hardware has been unplugged.
- Changed watchdog timeout routines to just call the driver init routines
to initialize the device states without trying to close and re-open the
pipes. This is partly because we don't want to frob things at interrupt
context, but also because this doesn't seem to work right and I don't
want to panic the system just because a USB device may have stopped
responding.
- Fix aue_rxeof() to be a little smarter about detecting when a double
transfer is needed. Unfortunately, the design of the chip makes it hard
to get this exactly right. Hopefully, this will go away once either
Nick or Lennart finds the bug in the uhci driver that makes this ugly
hack necessary.
- Also sync usbdevs with NetBSD.
