/* * Adaptec 274x/284x/294x device driver firmware for Linux and FreeBSD. * * Copyright (c) 1994-2000 Justin Gibbs. * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions, and the following disclaimer, * without modification. * 2. The name of the author may not be used to endorse or promote products * derived from this software without specific prior written permission. * * Alternatively, this software may be distributed under the terms of the * GNU Public License ("GPL"). * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. * * $FreeBSD$ */ #include #include /* * A few words on the waiting SCB list: * After starting the selection hardware, we check for reconnecting targets * as well as for our selection to complete just in case the reselection wins * bus arbitration. The problem with this is that we must keep track of the * SCB that we've already pulled from the QINFIFO and started the selection * on just in case the reselection wins so that we can retry the selection at * a later time. This problem cannot be resolved by holding a single entry * in scratch ram since a reconnecting target can request sense and this will * create yet another SCB waiting for selection. The solution used here is to * use byte 27 of the SCB as a psuedo-next pointer and to thread a list * of SCBs that are awaiting selection. Since 0-0xfe are valid SCB indexes, * SCB_LIST_NULL is 0xff which is out of range. An entry is also added to * this list everytime a request sense occurs or after completing a non-tagged * command for which a second SCB has been queued. The sequencer will * automatically consume the entries. */ reset: clr SCSISIGO; /* De-assert BSY */ mvi MSG_OUT, MSG_NOOP; /* No message to send */ and SXFRCTL1, ~BITBUCKET; /* Always allow reselection */ and SCSISEQ, ENSELI|ENRSELI|ENAUTOATNP, SCSISEQ_TEMPLATE; if ((ahc->features & AHC_CMD_CHAN) != 0) { /* Ensure that no DMA operations are in progress */ clr CCSGCTL; clr CCSCBCTL; } poll_for_work: call clear_target_state; and SXFRCTL0, ~SPIOEN; if ((ahc->features & AHC_QUEUE_REGS) == 0) { mov A, QINPOS; } poll_for_work_loop: test SSTAT0, SELDO|SELDI jnz selection; test SCSISEQ, ENSELO jnz poll_for_work_loop; if ((ahc->features & AHC_TWIN) != 0) { /* * Twin channel devices cannot handle things like SELTO * interrupts on the "background" channel. So, if we * are selecting, keep polling the current channel util * either a selection or reselection occurs. */ xor SBLKCTL,SELBUSB; /* Toggle to the other bus */ test SSTAT0, SELDO|SELDI jnz selection; test SCSISEQ, ENSELO jnz poll_for_work_loop; } cmp WAITING_SCBH,SCB_LIST_NULL jne start_waiting; test_queue: /* Has the driver posted any work for us? */ if ((ahc->features & AHC_QUEUE_REGS) != 0) { test QOFF_CTLSTA, SCB_AVAIL jz poll_for_work_loop; mov NONE, SNSCB_QOFF; inc QINPOS; } else { cmp KERNEL_QINPOS, A je poll_for_work_loop; inc QINPOS; } /* * We have at least one queued SCB now and we don't have any * SCBs in the list of SCBs awaiting selection. Pull the tag * from the QINFIFO and get to work on it. */ if ((ahc->flags & AHC_PAGESCBS) != 0) { mov ALLZEROS call get_free_or_disc_scb; } dequeue_scb: add A, -1, QINPOS; mvi QINFIFO_OFFSET call fetch_byte; if ((ahc->flags & AHC_PAGESCBS) == 0) { /* In the non-paging case, the SCBID == hardware SCB index */ mov SCBPTR, RETURN_2; } dma_queued_scb: /* * DMA the SCB from host ram into the current SCB location. */ mvi DMAPARAMS, HDMAEN|DIRECTION|FIFORESET; mov RETURN_2 call dma_scb; start_scb: /* * Place us on the waiting list in case our selection * doesn't win during bus arbitration. */ mov SCB_NEXT,WAITING_SCBH; mov WAITING_SCBH, SCBPTR; start_waiting: /* * Start the first entry on the waiting SCB list. */ mov SCBPTR, WAITING_SCBH; call start_selection; jmp poll_for_work; start_selection: if ((ahc->features & AHC_TWIN) != 0) { and SINDEX,~SELBUSB,SBLKCTL;/* Clear channel select bit */ test SCB_SCSIID, TWIN_CHNLB jz . + 2; or SINDEX, SELBUSB; mov SBLKCTL,SINDEX; /* select channel */ } initialize_scsiid: if ((ahc->features & AHC_ULTRA2) != 0) { mov SCSIID_ULTRA2, SCB_SCSIID; } else if ((ahc->features & AHC_TWIN) != 0) { and SCSIID, TWIN_TID|OID, SCB_SCSIID; } else { mov SCSIID, SCB_SCSIID; } if ((ahc->flags & AHC_TARGETMODE) != 0) { mov SINDEX, SCSISEQ_TEMPLATE; test SCB_CONTROL, TARGET_SCB jz . + 2; or SINDEX, TEMODE; mov SCSISEQ, SINDEX ret; } else { mov SCSISEQ, SCSISEQ_TEMPLATE ret; } /* * Initialize transfer settings and clear the SCSI channel. * SINDEX should contain any additional bit's the client wants * set in SXFRCTL0. We also assume that the current SCB is * a valid SCB for the target we wish to talk to. */ initialize_channel: or SXFRCTL0, CLRSTCNT|CLRCHN, SINDEX; set_transfer_settings: if ((ahc->features & AHC_ULTRA) != 0) { test SCB_CONTROL, ULTRAENB jz . + 2; or SXFRCTL0, FAST20; } /* * Initialize SCSIRATE with the appropriate value for this target. */ if ((ahc->features & AHC_ULTRA2) != 0) { bmov SCSIRATE, SCB_SCSIRATE, 2 ret; } else { mov SCSIRATE, SCB_SCSIRATE ret; } selection: /* * We aren't expecting a bus free, so interrupt * the kernel driver if it happens. */ mvi CLRSINT1,CLRBUSFREE; or SIMODE1, ENBUSFREE; test SSTAT0,SELDO jnz select_out; mvi CLRSINT0, CLRSELDI; select_in: if ((ahc->flags & AHC_TARGETMODE) != 0) { if ((ahc->flags & AHC_INITIATORMODE) != 0) { test SSTAT0, TARGET jz initiator_reselect; } /* * We've just been selected. Assert BSY and * setup the phase for receiving messages * from the target. */ mvi SCSISIGO, P_MESGOUT|BSYO; /* * Setup the DMA for sending the identify and * command information. */ or SEQ_FLAGS, CMDPHASE_PENDING; mov A, TQINPOS; if ((ahc->features & AHC_CMD_CHAN) != 0) { mvi DINDEX, CCHADDR; mvi SHARED_DATA_ADDR call set_32byte_addr; mvi CCSCBCTL, CCSCBRESET; } else { mvi DINDEX, HADDR; mvi SHARED_DATA_ADDR call set_32byte_addr; mvi DFCNTRL, FIFORESET; } /* Initiator that selected us */ and SAVED_SCSIID, SELID_MASK, SELID; /* The Target ID we were selected at */ if ((ahc->features & AHC_MULTI_TID) != 0) { and A, OID, TARGIDIN; } else if ((ahc->features & AHC_ULTRA2) != 0) { and A, OID, SCSIID_ULTRA2; } else { and A, OID, SCSIID; } or SAVED_SCSIID, A; if ((ahc->features & AHC_TWIN) != 0) { test SBLKCTL, SELBUSB jz . + 2; or SAVED_SCSIID, TWIN_CHNLB; } if ((ahc->features & AHC_CMD_CHAN) != 0) { mov CCSCBRAM, SAVED_SCSIID; } else { mov DFDAT, SAVED_SCSIID; } /* * If ATN isn't asserted, the target isn't interested * in talking to us. Go directly to bus free. * XXX SCSI-1 may require us to assume lun 0 if * ATN is false. */ test SCSISIGI, ATNI jz target_busfree; /* * Watch ATN closely now as we pull in messages from the * initiator. We follow the guidlines from section 6.5 * of the SCSI-2 spec for what messages are allowed when. */ call target_inb; /* * Our first message must be one of IDENTIFY, ABORT, or * BUS_DEVICE_RESET. */ test DINDEX, MSG_IDENTIFYFLAG jz host_target_message_loop; /* Store for host */ if ((ahc->features & AHC_CMD_CHAN) != 0) { mov CCSCBRAM, DINDEX; } else { mov DFDAT, DINDEX; } /* Remember for disconnection decision */ test DINDEX, MSG_IDENTIFY_DISCFLAG jnz . + 2; /* XXX Honor per target settings too */ or SEQ_FLAGS, NO_DISCONNECT; test SCSISIGI, ATNI jz ident_messages_done; call target_inb; /* * If this is a tagged request, the tagged message must * immediately follow the identify. We test for a valid * tag message by seeing if it is >= MSG_SIMPLE_Q_TAG and * < MSG_IGN_WIDE_RESIDUE. */ add A, -MSG_SIMPLE_Q_TAG, DINDEX; jnc ident_messages_done; add A, -MSG_IGN_WIDE_RESIDUE, DINDEX; jc ident_messages_done; /* Store for host */ if ((ahc->features & AHC_CMD_CHAN) != 0) { mov CCSCBRAM, DINDEX; } else { mov DFDAT, DINDEX; } /* * If the initiator doesn't feel like providing a tag number, * we've got a failed selection and must transition to bus * free. */ test SCSISIGI, ATNI jz target_busfree; /* * Store the tag for the host. */ call target_inb; if ((ahc->features & AHC_CMD_CHAN) != 0) { mov CCSCBRAM, DINDEX; } else { mov DFDAT, DINDEX; } mov INITIATOR_TAG, DINDEX; or SEQ_FLAGS, TARGET_CMD_IS_TAGGED; test SCSISIGI, ATNI jz . + 2; /* Initiator still wants to give us messages */ call target_inb; jmp ident_messages_done; /* * Pushed message loop to allow the kernel to * run it's own target mode message state engine. */ host_target_message_loop: mvi INTSTAT, HOST_MSG_LOOP; nop; cmp RETURN_1, EXIT_MSG_LOOP je target_ITloop; test SSTAT0, SPIORDY jz .; jmp host_target_message_loop; ident_messages_done: /* If ring buffer is full, return busy or queue full */ if ((ahc->features & AHC_HS_MAILBOX) != 0) { and A, HOST_TQINPOS, HS_MAILBOX; } else { mov A, KERNEL_TQINPOS; } cmp TQINPOS, A jne tqinfifo_has_space; mvi P_STATUS|BSYO call change_phase; test SEQ_FLAGS, TARGET_CMD_IS_TAGGED jnz . + 3; mvi STATUS_QUEUE_FULL call target_outb; jmp target_busfree_wait; mvi STATUS_BUSY call target_outb; jmp target_busfree_wait; tqinfifo_has_space: /* Terminate the ident list */ if ((ahc->features & AHC_CMD_CHAN) != 0) { mvi CCSCBRAM, SCB_LIST_NULL; } else { mvi DFDAT, SCB_LIST_NULL; } or SEQ_FLAGS, TARG_CMD_PENDING|IDENTIFY_SEEN; test SCSISIGI, ATNI jnz target_mesgout_pending; jmp target_ITloop; /* * We carefully toggle SPIOEN to allow us to return the * message byte we receive so it can be checked prior to * driving REQ on the bus for the next byte. */ target_inb: /* * Drive REQ on the bus by enabling SCSI PIO. */ or SXFRCTL0, SPIOEN; /* Wait for the byte */ test SSTAT0, SPIORDY jz .; /* Prevent our read from triggering another REQ */ and SXFRCTL0, ~SPIOEN; /* Save latched contents */ mov DINDEX, SCSIDATL ret; } if ((ahc->flags & AHC_INITIATORMODE) != 0) { /* * Reselection has been initiated by a target. Make a note that we've been * reselected, but haven't seen an IDENTIFY message from the target yet. */ initiator_reselect: /* XXX test for and handle ONE BIT condition */ and SAVED_SCSIID, SELID_MASK, SELID; if ((ahc->features & AHC_ULTRA2) != 0) { and A, OID, SCSIID_ULTRA2; } else { and A, OID, SCSIID; } or SAVED_SCSIID, A; if ((ahc->features & AHC_TWIN) != 0) { test SBLKCTL, SELBUSB jz . + 2; or SAVED_SCSIID, TWIN_CHNLB; } or SXFRCTL0, SPIOEN|CLRSTCNT|CLRCHN; jmp ITloop; } /* * After the selection, remove this SCB from the "waiting SCB" * list. This is achieved by simply moving our "next" pointer into * WAITING_SCBH. Our next pointer will be set to null the next time this * SCB is used, so don't bother with it now. */ select_out: /* Turn off the selection hardware */ and SCSISEQ, TEMODE|ENSELI|ENRSELI|ENAUTOATNP, SCSISEQ; mvi CLRSINT0, CLRSELDO; mov SCBPTR, WAITING_SCBH; mov WAITING_SCBH,SCB_NEXT; mov SAVED_SCSIID, SCB_SCSIID; mov SAVED_LUN, SCB_LUN; mvi SPIOEN call initialize_channel; if ((ahc->flags & AHC_TARGETMODE) != 0) { test SSTAT0, TARGET jz initiator_select; /* * We've just re-selected an initiator. * Assert BSY and setup the phase for * sending our identify messages. */ mvi P_MESGIN|BSYO call change_phase; /* * Start out with a simple identify message. */ or SCB_LUN, MSG_IDENTIFYFLAG call target_outb; /* * If we are the result of a tagged command, send * a simple Q tag and the tag id. */ test SCB_CONTROL, TAG_ENB jz . + 3; mvi MSG_SIMPLE_Q_TAG call target_outb; mov SCB_TARGET_INFO[SCB_INITIATOR_TAG] call target_outb; target_synccmd: /* * Now determine what phases the host wants us * to go through. */ mov SEQ_FLAGS, SCB_TARGET_INFO[SCB_TARGET_PHASES]; target_ITloop: /* * Start honoring ATN signals now that * we properly identified ourselves. */ test SCSISIGI, ATNI jnz target_mesgout; test SEQ_FLAGS, CMDPHASE_PENDING jnz target_cmdphase; test SEQ_FLAGS, DPHASE_PENDING jnz target_dphase; test SEQ_FLAGS, SPHASE_PENDING jnz target_sphase; /* * No more work to do. Either disconnect or not depending * on the state of NO_DISCONNECT. */ test SEQ_FLAGS, NO_DISCONNECT jz target_disconnect; if ((ahc->flags & AHC_PAGESCBS) != 0) { mov ALLZEROS call get_free_or_disc_scb; } mov RETURN_1, ALLZEROS; call complete_target_cmd; cmp RETURN_1, CONT_MSG_LOOP jne .; mvi DMAPARAMS, HDMAEN|DIRECTION|FIFORESET; mov SCB_TAG call dma_scb; jmp target_synccmd; target_mesgout: mvi SCSISIGO, P_MESGOUT|BSYO; target_mesgout_continue: call target_inb; target_mesgout_pending: /* Local Processing goes here... */ jmp host_target_message_loop; target_disconnect: mvi P_MESGIN|BSYO call change_phase; test SEQ_FLAGS, DPHASE jz . + 2; mvi MSG_SAVEDATAPOINTER call target_outb; mvi MSG_DISCONNECT call target_outb; target_busfree_wait: /* Wait for preceeding I/O session to complete. */ test SCSISIGI, ACKI jnz .; target_busfree: and SIMODE1, ~ENBUSFREE; clr SCSISIGO; mvi LASTPHASE, P_BUSFREE; call complete_target_cmd; jmp poll_for_work; target_cmdphase: mvi P_COMMAND|BSYO call change_phase; call target_inb; mov A, DINDEX; /* Store for host */ if ((ahc->features & AHC_CMD_CHAN) != 0) { mov CCSCBRAM, A; } else { mov DFDAT, A; } /* * Determine the number of bytes to read * based on the command group code via table lookup. * We reuse the first 8 bytes of the TARG_SCSIRATE * BIOS array for this table. Count is one less than * the total for the command since we've already fetched * the first byte. */ shr A, CMD_GROUP_CODE_SHIFT; add SINDEX, TARG_SCSIRATE, A; mov A, SINDIR; test A, 0xFF jz command_phase_done; command_loop: or SXFRCTL0, SPIOEN; test SSTAT0, SPIORDY jz .; cmp A, 1 jne . + 2; and SXFRCTL0, ~SPIOEN; /* Last Byte */ if ((ahc->features & AHC_CMD_CHAN) != 0) { mov CCSCBRAM, SCSIDATL; } else { mov DFDAT, SCSIDATL; } dec A; test A, 0xFF jnz command_loop; command_phase_done: and SEQ_FLAGS, ~CMDPHASE_PENDING; jmp target_ITloop; target_dphase: /* * Data phases on the bus are from the * perspective of the initiator. The dma * code looks at LASTPHASE to determine the * data direction of the DMA. Toggle it for * target transfers. */ xor LASTPHASE, IOI, SCB_TARGET_INFO[SCB_TARGET_DATA_DIR]; or SCB_TARGET_INFO[SCB_TARGET_DATA_DIR], BSYO call change_phase; jmp p_data; target_sphase: mvi P_STATUS|BSYO call change_phase; mvi LASTPHASE, P_STATUS; mov SCB_TARGET_INFO[SCB_TARGET_STATUS] call target_outb; /* XXX Watch for ATN or parity errors??? */ mvi SCSISIGO, P_MESGIN|BSYO; /* MSG_CMDCMPLT is 0, but we can't do an immediate of 0 */ mov ALLZEROS call target_outb; jmp target_busfree_wait; complete_target_cmd: test SEQ_FLAGS, TARG_CMD_PENDING jnz . + 2; mov SCB_TAG jmp complete_post; if ((ahc->features & AHC_CMD_CHAN) != 0) { /* Set the valid byte */ mvi CCSCBADDR, 24; mov CCSCBRAM, ALLONES; mvi CCHCNT, 28; or CCSCBCTL, CCSCBEN|CCSCBRESET; test CCSCBCTL, CCSCBDONE jz .; clr CCSCBCTL; } else { /* Set the valid byte */ or DFCNTRL, FIFORESET; mvi DFWADDR, 3; /* Third 64bit word or byte 24 */ mov DFDAT, ALLONES; mvi 28 call set_hcnt; or DFCNTRL, HDMAEN|FIFOFLUSH; call dma_finish; } inc TQINPOS; mvi INTSTAT,CMDCMPLT ret; } if ((ahc->flags & AHC_INITIATORMODE) != 0) { initiator_select: /* * As soon as we get a successful selection, the target * should go into the message out phase since we have ATN * asserted. */ mvi MSG_OUT, MSG_IDENTIFYFLAG; or SEQ_FLAGS, IDENTIFY_SEEN; /* * Main loop for information transfer phases. Wait for the * target to assert REQ before checking MSG, C/D and I/O for * the bus phase. */ mesgin_phasemis: ITloop: call phase_lock; mov A, LASTPHASE; test A, ~P_DATAIN jz p_data; cmp A,P_COMMAND je p_command; cmp A,P_MESGOUT je p_mesgout; cmp A,P_STATUS je p_status; cmp A,P_MESGIN je p_mesgin; mvi INTSTAT,BAD_PHASE; jmp ITloop; /* Try reading the bus again. */ await_busfree: and SIMODE1, ~ENBUSFREE; mov NONE, SCSIDATL; /* Ack the last byte */ and SXFRCTL0, ~SPIOEN; test SSTAT1,REQINIT|BUSFREE jz .; test SSTAT1, BUSFREE jnz poll_for_work; mvi INTSTAT, BAD_PHASE; } clear_target_state: /* * We assume that the kernel driver may reset us * at any time, even in the middle of a DMA, so * clear DFCNTRL too. */ clr DFCNTRL; mvi SXFRCTL0, CLRSTCNT|CLRCHN; /* * We don't know the target we will connect to, * so default to narrow transfers to avoid * parity problems. */ if ((ahc->features & AHC_ULTRA2) != 0) { bmov SCSIRATE, ALLZEROS, 2; } else { clr SCSIRATE; if ((ahc->features & AHC_ULTRA) != 0) { and SXFRCTL0, ~(FAST20); } } mvi LASTPHASE, P_BUSFREE; /* clear target specific flags */ clr SEQ_FLAGS ret; sg_advance: clr A; /* add sizeof(struct scatter) */ add SCB_RESIDUAL_SGPTR[0],SG_SIZEOF; adc SCB_RESIDUAL_SGPTR[1],A; adc SCB_RESIDUAL_SGPTR[2],A; adc SCB_RESIDUAL_SGPTR[3],A ret; idle_loop: if ((ahc->features & AHC_CMD_CHAN) != 0) { /* Did we just finish fetching segs? */ cmp CCSGCTL, CCSGEN|CCSGDONE je idle_sgfetch_complete; /* Are we actively fetching segments? */ test CCSGCTL, CCSGEN jnz return; /* * Do we need any more segments? */ test SCB_RESIDUAL_DATACNT[3], SG_LAST_SEG jnz return; /* * Do we have any prefetch left??? */ cmp CCSGADDR, CCSGADDR_MAX jne idle_sg_avail; /* * Need to fetch segments, but we can only do that * if the command channel is completely idle. Make * sure we don't have an SCB prefetch going on. */ test CCSCBCTL, CCSCBEN jnz return; /* * The kernel allocates S/G space so that it is 128 byte * aligned and ends on a 128 byte boundary. We fetch * up to the next 128 byte boundary so we don't attempt * to read a non-existent page. */ mvi CCHCNT, CCSGADDR_MAX; and CCHADDR[0], ~(CCSGADDR_MAX - 1), SCB_RESIDUAL_SGPTR; bmov CCHADDR[1], SCB_RESIDUAL_SGPTR[1], 3; mvi CCSGCTL, CCSGEN|CCSGRESET ret; idle_sgfetch_complete: mvi CCSGCTL, CCSGRESET; and CCSGADDR, (CCSGADDR_MAX - 1), SCB_RESIDUAL_SGPTR; idle_sg_avail: if ((ahc->features & AHC_ULTRA2) != 0) { /* Does the hardware have space for another SG entry? */ test DFSTATUS, PRELOAD_AVAIL jz return; bmov HADDR, CCSGRAM, 4; bmov SINDEX, CCSGRAM, 1; test SINDEX, 0x1 jz . + 2; xor DATA_COUNT_ODD, 0x1; bmov HCNT[0], SINDEX, 1; bmov HCNT[1], CCSGRAM, 2; bmov SCB_RESIDUAL_DATACNT[3], CCSGRAM, 1; call sg_advance; mov SINDEX, SCB_RESIDUAL_SGPTR[0]; test DATA_COUNT_ODD, 0x1 jz . + 2; or SINDEX, ODD_SEG; test SCB_RESIDUAL_DATACNT[3], SG_LAST_SEG jz . + 2; or SINDEX, LAST_SEG; mov SG_CACHE_PRE, SINDEX; /* Load the segment by writing DFCNTRL again */ mov DFCNTRL, DMAPARAMS; } ret; } /* * If we re-enter the data phase after going through another phase, the * STCNT may have been cleared, so restore it from the residual field. */ data_phase_reinit: if ((ahc->features & AHC_ULTRA2) != 0) { /* * The preload circuitry requires us to * reload the address too, so pull it from * the shaddow address. */ bmov HADDR, SHADDR, 4; bmov HCNT, SCB_RESIDUAL_DATACNT, 3; } else if ((ahc->features & AHC_CMD_CHAN) != 0) { bmov STCNT, SCB_RESIDUAL_DATACNT, 3; } else { mvi DINDEX, STCNT; mvi SCB_RESIDUAL_DATACNT call bcopy_3; } and DATA_COUNT_ODD, 0x1, SCB_RESIDUAL_DATACNT[0]; jmp data_phase_loop; p_data: if ((ahc->features & AHC_ULTRA2) != 0) { mvi DMAPARAMS, PRELOADEN|SCSIEN|HDMAEN; } else { mvi DMAPARAMS, WIDEODD|SCSIEN|SDMAEN|HDMAEN|FIFORESET; } test LASTPHASE, IOI jnz . + 2; or DMAPARAMS, DIRECTION; call assert; /* * Ensure entering a data * phase is okay - seen identify, etc. */ if ((ahc->features & AHC_CMD_CHAN) != 0) { /* We don't have any valid S/G elements */ mvi CCSGADDR, CCSGADDR_MAX; } test SEQ_FLAGS, DPHASE jnz data_phase_reinit; /* We have seen a data phase */ or SEQ_FLAGS, DPHASE; /* * Initialize the DMA address and counter from the SCB. * Also set SCB_RESIDUAL_SGPTR, including the LAST_SEG * flag in the highest byte of the data count. We cannot * modify the saved values in the SCB until we see a save * data pointers message. */ if ((ahc->features & AHC_CMD_CHAN) != 0) { bmov HADDR, SCB_DATAPTR, 7; bmov SCB_RESIDUAL_DATACNT[3], SCB_DATACNT[3], 5; } else { mvi DINDEX, HADDR; mvi SCB_DATAPTR call bcopy_7; mvi DINDEX, SCB_RESIDUAL_DATACNT + 3; mvi SCB_DATACNT + 3 call bcopy_5; } and SCB_RESIDUAL_SGPTR[0], ~SG_FULL_RESID; and DATA_COUNT_ODD, 0x1, SCB_DATACNT[0]; if ((ahc->features & AHC_ULTRA2) == 0) { if ((ahc->features & AHC_CMD_CHAN) != 0) { bmov STCNT, HCNT, 3; } else { call set_stcnt_from_hcnt; } } data_phase_loop: /* Guard against overruns */ test SCB_RESIDUAL_SGPTR[0], SG_LIST_NULL jz data_phase_inbounds; /* * Turn on 'Bit Bucket' mode, set the transfer count to * 16meg and let the target run until it changes phase. * When the transfer completes, notify the host that we * had an overrun. */ or SXFRCTL1,BITBUCKET; and DMAPARAMS, ~(HDMAEN|SDMAEN); /* Keep our idle loop from mucking with SG segments */ or SCB_RESIDUAL_DATACNT[0], SG_LAST_SEG; if ((ahc->features & AHC_ULTRA2) != 0) { bmov HCNT, ALLONES, 3; } else if ((ahc->features & AHC_CMD_CHAN) != 0) { bmov STCNT, ALLONES, 3; } else { /* XXX Use bcopy? */ mvi STCNT[0], 0xFF; mvi STCNT[1], 0xFF; mvi STCNT[2], 0xFF; } data_phase_inbounds: if ((ahc->features & AHC_ULTRA2) != 0) { mov SINDEX, SCB_RESIDUAL_SGPTR[0]; test SCB_RESIDUAL_DATACNT[3], SG_LAST_SEG jz . + 2; or SINDEX, LAST_SEG; test DATA_COUNT_ODD, 0x1 jz . + 2; or SINDEX, ODD_SEG; mov SG_CACHE_PRE, SINDEX; mov DFCNTRL, DMAPARAMS; ultra2_dma_loop: call idle_loop; /* * The transfer is complete if either the last segment * completes or the target changes phase. */ test SG_CACHE_SHADOW, LAST_SEG_DONE jnz ultra2_dmafinish; test SSTAT1,PHASEMIS jz ultra2_dma_loop; ultra2_dmafinish: test DFCNTRL, DIRECTION jnz ultra2_dmafifoempty; and DFCNTRL, ~SCSIEN; test DFCNTRL, SCSIEN jnz .; ultra2_dmafifoflush: if ((ahc->bugs & AHC_AUTOFLUSH_BUG) != 0) { /* * On Rev A of the aic7890, the autoflush * features doesn't function correctly. * Perform an explicit manual flush. During * a manual flush, the FIFOEMP bit becomes * true every time the PCI FIFO empties * regardless of the state of the SCSI FIFO. * It can take up to 4 clock cycles for the * SCSI FIFO to get data into the PCI FIFO * and for FIFOEMP to de-assert. Here we * guard against this condition by making * sure the FIFOEMP bit stays on for 5 full * clock cycles. */ or DFCNTRL, FIFOFLUSH; test DFSTATUS, FIFOEMP jz ultra2_dmafifoflush; test DFSTATUS, FIFOEMP jz ultra2_dmafifoflush; test DFSTATUS, FIFOEMP jz ultra2_dmafifoflush; test DFSTATUS, FIFOEMP jz ultra2_dmafifoflush; } test DFSTATUS, FIFOEMP jz ultra2_dmafifoflush; ultra2_dmafifoempty: /* Don't clobber an inprogress host data transfer */ test DFSTATUS, MREQPEND jnz ultra2_dmafifoempty; ultra2_dmahalt: and DFCNTRL, ~(SCSIEN|HDMAEN); test DFCNTRL, HDMAEN jnz .; test SXFRCTL1,BITBUCKET jnz data_phase_finish; /* * Fixup the residual next S/G pointer. The S/G preload * feature of the chip allows us to load two elements * in addition to the currently active element. We * store the bottom byte of the next S/G pointer in * the SG_CACEPTR register so we can restore the * correct value when the DMA completes. If the next * sg ptr value has advanced to the point where higher * bytes in the address have been affected, fix them * too. */ test SG_CACHE_SHADOW, 0x80 jz sgptr_fixup_done; test SCB_RESIDUAL_SGPTR[0], 0x80 jnz sgptr_fixup_done; add SCB_RESIDUAL_SGPTR[1], -1; adc SCB_RESIDUAL_SGPTR[2], -1; adc SCB_RESIDUAL_SGPTR[3], -1; sgptr_fixup_done: and SCB_RESIDUAL_SGPTR[0], SG_ADDR_MASK, SG_CACHE_SHADOW; clr DATA_COUNT_ODD; test SG_CACHE_SHADOW, ODD_SEG jz . + 2; or DATA_COUNT_ODD, 0x1; clr SCB_RESIDUAL_DATACNT[3]; test SG_CACHE_SHADOW, LAST_SEG jz data_phase_finish; or SCB_RESIDUAL_DATACNT[3], SG_LAST_SEG; /* Record if we've consumed all S/G entries */ test SG_CACHE_SHADOW, LAST_SEG_DONE jz . + 2; or SCB_RESIDUAL_SGPTR[0], SG_LIST_NULL; } else { /* If we are the last SG block, tell the hardware. */ test SCB_RESIDUAL_DATACNT[3], SG_LAST_SEG jz dma_mid_sg; if ((ahc->flags & AHC_TARGETMODE) != 0) { test SSTAT0, TARGET jz . + 2; test DMAPARAMS, DIRECTION jz dma_mid_sg; } and DMAPARAMS, ~WIDEODD; dma_mid_sg: /* Start DMA data transfer. */ mov DFCNTRL, DMAPARAMS; dma_loop: if ((ahc->features & AHC_CMD_CHAN) != 0) { call idle_loop; } test SSTAT0,DMADONE jnz dma_dmadone; test SSTAT1,PHASEMIS jz dma_loop; /* ie. underrun */ dma_phasemis: /* * We will be "done" DMAing when the transfer count goes to * zero, or the target changes the phase (in light of this, * it makes sense that the DMA circuitry doesn't ACK when * PHASEMIS is active). If we are doing a SCSI->Host transfer, * the data FIFO should be flushed auto-magically on STCNT=0 * or a phase change, so just wait for FIFO empty status. */ dma_checkfifo: test DFCNTRL,DIRECTION jnz dma_fifoempty; dma_fifoflush: test DFSTATUS,FIFOEMP jz dma_fifoflush; dma_fifoempty: /* Don't clobber an inprogress host data transfer */ test DFSTATUS, MREQPEND jnz dma_fifoempty; /* * Now shut off the DMA and make sure that the DMA * hardware has actually stopped. Touching the DMA * counters, etc. while a DMA is active will result * in an ILLSADDR exception. */ dma_dmadone: and DFCNTRL, ~(SCSIEN|SDMAEN|HDMAEN); dma_halt: /* * Some revisions of the aic7880 have a problem where, if the * data fifo is full, but the PCI input latch is not empty, * HDMAEN cannot be cleared. The fix used here is to drain * the prefetched but unused data from the data fifo until * there is space for the input latch to drain. */ mov NONE, DFDAT; test DFCNTRL, (SCSIEN|SDMAEN|HDMAEN) jnz dma_halt; /* See if we have completed this last segment */ test STCNT[0], 0xff jnz data_phase_finish; test STCNT[1], 0xff jnz data_phase_finish; test STCNT[2], 0xff jnz data_phase_finish; /* * Advance the scatter-gather pointers if needed */ test SCB_RESIDUAL_DATACNT[3], SG_LAST_SEG jz sg_load; or SCB_RESIDUAL_SGPTR[0], SG_LIST_NULL; jmp data_phase_finish; sg_load: /* * Load the next SG element's data address and length * into the DMA engine. If we don't have hardware * to perform a prefetch, we'll have to fetch the * segment from host memory first. */ if ((ahc->features & AHC_CMD_CHAN) != 0) { /* Wait for the idle loop to complete */ test CCSGCTL, CCSGEN jz . + 3; call idle_loop; test CCSGCTL, CCSGEN jnz . - 1; bmov HADDR, CCSGRAM, 7; bmov SCB_RESIDUAL_DATACNT[3], CCSGRAM, 1; bmov STCNT, HCNT, 3; } else { mvi DINDEX, HADDR; mvi SCB_RESIDUAL_SGPTR call bcopy_4; mvi SG_SIZEOF call set_hcnt; or DFCNTRL, HDMAEN|DIRECTION|FIFORESET; call dma_finish; mvi HADDR call dfdat_in_7; mov SCB_RESIDUAL_DATACNT[3], DFDAT; call set_stcnt_from_hcnt; } /* Track odd'ness */ test HCNT[0], 0x1 jz . + 2; xor DATA_COUNT_ODD, 0x1; /* Point to the new next sg in memory */ call sg_advance; if ((ahc->flags & AHC_TARGETMODE) != 0) { test SSTAT0, TARGET jnz data_phase_loop; } } data_phase_finish: /* * If the target has left us in data phase, loop through * the dma code again. In the case of ULTRA2 adapters, * we should only loop if there is a data overrun. For * all other adapters, we'll loop after each S/G element * is loaded as well as if there is an overrun. */ if ((ahc->flags & AHC_TARGETMODE) != 0) { test SSTAT0, TARGET jnz data_phase_done; } if ((ahc->flags & AHC_INITIATORMODE) != 0) { test SSTAT1, REQINIT jz .; test SSTAT1,PHASEMIS jz data_phase_loop; if ((ahc->features & AHC_CMD_CHAN) != 0) { /* Kill off any pending prefetch */ clr CCSGCTL; test CCSGCTL, CCSGEN jnz .; } /* * Turn off BITBUCKET mode and notify the host * in the event of an overrun. */ test SXFRCTL1,BITBUCKET jz data_phase_done; and SXFRCTL1, ~BITBUCKET; mvi INTSTAT,DATA_OVERRUN; jmp ITloop; } data_phase_done: /* * After a DMA finishes, save the SG and STCNT residuals back into * the SCB. We use STCNT instead of HCNT, since it's a reflection * of how many bytes were transferred on the SCSI (as opposed to the * host) bus. */ if ((ahc->features & AHC_CMD_CHAN) != 0) { /* Kill off any pending prefetch */ clr CCSGCTL; test CCSGCTL, CCSGEN jnz .; bmov SCB_RESIDUAL_DATACNT, STCNT, 3; } else { mov SCB_RESIDUAL_DATACNT[0],STCNT[0]; mov SCB_RESIDUAL_DATACNT[1],STCNT[1]; mov SCB_RESIDUAL_DATACNT[2],STCNT[2]; } /* * Since we've been through a data phase, the SCB_RESID* fields * are now initialized. Clear the full residual flag. */ and SCB_SGPTR[0], ~SG_FULL_RESID; if ((ahc->features & AHC_ULTRA2) != 0) { /* Clear the channel in case we return to data phase later */ or SXFRCTL0, CLRSTCNT|CLRCHN; } if ((ahc->flags & AHC_TARGETMODE) != 0) { test SEQ_FLAGS, DPHASE_PENDING jz ITloop; and SEQ_FLAGS, ~DPHASE_PENDING; /* * For data-in phases, wait for any pending acks from the * initiator before changing phase. */ test DFCNTRL, DIRECTION jz target_ITloop; test SSTAT1, REQINIT jnz .; jmp target_ITloop; } else { jmp ITloop; } if ((ahc->flags & AHC_INITIATORMODE) != 0) { /* * Command phase. Set up the DMA registers and let 'er rip. */ p_command: call assert; if ((ahc->features & AHC_ULTRA2) != 0) { bmov HCNT[0], SCB_CDB_LEN, 1; bmov HCNT[1], ALLZEROS, 2; } else if ((ahc->features & AHC_CMD_CHAN) != 0) { bmov STCNT[0], SCB_CDB_LEN, 1; bmov STCNT[1], ALLZEROS, 2; } else { mov STCNT[0], SCB_CDB_LEN; clr STCNT[1]; clr STCNT[2]; } add NONE, -13, SCB_CDB_LEN; mvi SCB_CDB_STORE jnc p_command_embedded; p_command_from_host: if ((ahc->features & AHC_ULTRA2) != 0) { bmov HADDR[0], SCB_CDB_PTR, 4; mvi DFCNTRL, (PRELOADEN|SCSIEN|HDMAEN|DIRECTION); } else { if ((ahc->features & AHC_CMD_CHAN) != 0) { bmov HADDR[0], SCB_CDB_PTR, 4; bmov HCNT[0], STCNT[0], 3; } else { mvi DINDEX, HADDR; mvi SCB_CDB_PTR call bcopy_5; call clear_hcnt; } mvi DFCNTRL, (SCSIEN|SDMAEN|HDMAEN|DIRECTION|FIFORESET); } jmp p_command_loop; p_command_embedded: /* * The data fifo seems to require 4 byte alligned * transfers from the sequencer. Force this to * be the case by clearing HADDR[0] even though * we aren't going to touch host memeory. */ clr HADDR[0]; if ((ahc->features & AHC_ULTRA2) != 0) { mvi DFCNTRL, (PRELOADEN|SCSIEN|DIRECTION); } else { mvi DFCNTRL, (SCSIEN|SDMAEN|DIRECTION|FIFORESET); } if ((ahc->features & AHC_CMD_CHAN) != 0) { bmov DFDAT, SCB_CDB_STORE, 12; } else { /* * At most 12 bytes, but we copy 16 to fill * the 64bit words in the FIFO */ call copy_to_fifo_8; call copy_to_fifo_8; } p_command_loop: test SSTAT0, SDONE jnz . + 2; test SSTAT1, PHASEMIS jz p_command_loop; /* * Wait for our ACK to go-away on it's own * instead of being killed by SCSIEN getting cleared. */ test SCSISIGI, ACKI jnz .; and DFCNTRL, ~(SCSIEN|SDMAEN|HDMAEN); test DFCNTRL, (SCSIEN|SDMAEN|HDMAEN) jnz .; jmp ITloop; /* * Status phase. Wait for the data byte to appear, then read it * and store it into the SCB. */ p_status: call assert; mov SCB_SCSI_STATUS, SCSIDATL; jmp ITloop; /* * Message out phase. If MSG_OUT is MSG_IDENTIFYFLAG, build a full * indentify message sequence and send it to the target. The host may * override this behavior by setting the MK_MESSAGE bit in the SCB * control byte. This will cause us to interrupt the host and allow * it to handle the message phase completely on its own. If the bit * associated with this target is set, we will also interrupt the host, * thereby allowing it to send a message on the next selection regardless * of the transaction being sent. * * If MSG_OUT is == HOST_MSG, also interrupt the host and take a message. * This is done to allow the host to send messages outside of an identify * sequence while protecting the seqencer from testing the MK_MESSAGE bit * on an SCB that might not be for the current nexus. (For example, a * BDR message in responce to a bad reselection would leave us pointed to * an SCB that doesn't have anything to do with the current target). * * Otherwise, treat MSG_OUT as a 1 byte message to send (abort, abort tag, * bus device reset). * * When there are no messages to send, MSG_OUT should be set to MSG_NOOP, * in case the target decides to put us in this phase for some strange * reason. */ p_mesgout_retry: or SCSISIGO,ATNO,LASTPHASE;/* turn on ATN for the retry */ p_mesgout: mov SINDEX, MSG_OUT; cmp SINDEX, MSG_IDENTIFYFLAG jne p_mesgout_from_host; test SCB_CONTROL,MK_MESSAGE jnz host_message_loop; mov FUNCTION1, SCB_SCSIID; mov A, FUNCTION1; mov SINDEX, TARGET_MSG_REQUEST[0]; if ((ahc->features & AHC_TWIN) != 0) { /* Second Channel uses high byte bits */ test SCB_SCSIID, TWIN_CHNLB jz . + 2; mov SINDEX, TARGET_MSG_REQUEST[1]; } else if ((ahc->features & AHC_WIDE) != 0) { test SCB_SCSIID, 0x80 jz . + 2; /* target > 7 */ mov SINDEX, TARGET_MSG_REQUEST[1]; } test SINDEX, A jnz host_message_loop; p_mesgout_identify: or SINDEX, MSG_IDENTIFYFLAG|DISCENB, SCB_LUN; test SCB_CONTROL, DISCENB jnz . + 2; and SINDEX, ~DISCENB; /* * Send a tag message if TAG_ENB is set in the SCB control block. * Use SCB_TAG (the position in the kernel's SCB array) as the tag value. */ p_mesgout_tag: test SCB_CONTROL,TAG_ENB jz p_mesgout_onebyte; mov SCSIDATL, SINDEX; /* Send the identify message */ call phase_lock; cmp LASTPHASE, P_MESGOUT jne p_mesgout_done; and SCSIDATL,TAG_ENB|SCB_TAG_TYPE,SCB_CONTROL; call phase_lock; cmp LASTPHASE, P_MESGOUT jne p_mesgout_done; mov SCB_TAG jmp p_mesgout_onebyte; /* * Interrupt the driver, and allow it to handle this message * phase and any required retries. */ p_mesgout_from_host: cmp SINDEX, HOST_MSG jne p_mesgout_onebyte; jmp host_message_loop; p_mesgout_onebyte: mvi CLRSINT1, CLRATNO; mov SCSIDATL, SINDEX; /* * If the next bus phase after ATN drops is message out, it means * that the target is requesting that the last message(s) be resent. */ call phase_lock; cmp LASTPHASE, P_MESGOUT je p_mesgout_retry; p_mesgout_done: mvi CLRSINT1,CLRATNO; /* Be sure to turn ATNO off */ mov LAST_MSG, MSG_OUT; mvi MSG_OUT, MSG_NOOP; /* No message left */ jmp ITloop; /* * Message in phase. Bytes are read using Automatic PIO mode. */ p_mesgin: mvi ACCUM call inb_first; /* read the 1st message byte */ test A,MSG_IDENTIFYFLAG jnz mesgin_identify; cmp A,MSG_DISCONNECT je mesgin_disconnect; cmp A,MSG_SAVEDATAPOINTER je mesgin_sdptrs; cmp ALLZEROS,A je mesgin_complete; cmp A,MSG_RESTOREPOINTERS je mesgin_rdptrs; cmp A,MSG_IGN_WIDE_RESIDUE je mesgin_ign_wide_residue; cmp A,MSG_NOOP je mesgin_done; /* * Pushed message loop to allow the kernel to * run it's own message state engine. To avoid an * extra nop instruction after signaling the kernel, * we perform the phase_lock before checking to see * if we should exit the loop and skip the phase_lock * in the ITloop. Performing back to back phase_locks * shouldn't hurt, but why do it twice... */ host_message_loop: nop; mvi INTSTAT, HOST_MSG_LOOP; call phase_lock; cmp RETURN_1, EXIT_MSG_LOOP je ITloop + 1; jmp host_message_loop; mesgin_ign_wide_residue: if ((ahc->features & AHC_WIDE) != 0) { test SCSIRATE, WIDEXFER jz mesgin_reject; /* Pull the residue byte */ mvi ARG_1 call inb_next; cmp ARG_1, 0x01 jne mesgin_reject; test SCB_RESIDUAL_SGPTR[0], SG_LIST_NULL jz . + 2; test DATA_COUNT_ODD, 0x1 jz mesgin_done; mvi INTSTAT, IGN_WIDE_RES; jmp mesgin_done; } mesgin_reject: mvi MSG_MESSAGE_REJECT call mk_mesg; mesgin_done: mov NONE,SCSIDATL; /*dummy read from latch to ACK*/ jmp ITloop; mesgin_complete: /* * We received a "command complete" message. Put the SCB_TAG into the QOUTFIFO, * and trigger a completion interrupt. Before doing so, check to see if there * is a residual or the status byte is something other than STATUS_GOOD (0). * In either of these conditions, we upload the SCB back to the host so it can * process this information. In the case of a non zero status byte, we * additionally interrupt the kernel driver synchronously, allowing it to * decide if sense should be retrieved. If the kernel driver wishes to request * sense, it will fill the kernel SCB with a request sense command and set * RETURN_1 to SEND_SENSE. If RETURN_1 is set to SEND_SENSE we redownload * the SCB, and process it as the next command by adding it to the waiting list. * If the kernel driver does not wish to request sense, it need only clear * RETURN_1, and the command is allowed to complete normally. We don't bother * to post to the QOUTFIFO in the error cases since it would require extra * work in the kernel driver to ensure that the entry was removed before the * command complete code tried processing it. */ /* * First check for residuals */ test SCB_SGPTR, SG_LIST_NULL jnz check_status;/* No xfer */ test SCB_SGPTR, SG_FULL_RESID jnz upload_scb;/* Never xfered */ test SCB_RESIDUAL_SGPTR, SG_LIST_NULL jz upload_scb; check_status: test SCB_SCSI_STATUS,0xff jz complete; /* Good Status? */ upload_scb: or SCB_SGPTR, SG_RESID_VALID; mvi DMAPARAMS, FIFORESET; mov SCB_TAG call dma_scb; test SCB_SCSI_STATUS, 0xff jz complete; /* Just a residual? */ mvi INTSTAT, BAD_STATUS; /* let driver know */ /* * Prepare to DMA this SCB in case we are told to retrieve sense. * Fills a delay slot after the INTSTAT as well. */ mvi DMAPARAMS, HDMAEN|DIRECTION|FIFORESET; cmp RETURN_1, SEND_SENSE jne complete; mov SCB_TAG call dma_scb; add_to_waiting_list: mov SCB_NEXT,WAITING_SCBH; mov WAITING_SCBH, SCBPTR; /* * Prepare our selection hardware before the busfree so we have a * high probability of winning arbitration. */ call start_selection; jmp await_busfree; complete: mov SCB_TAG call complete_post; jmp await_busfree; } complete_post: /* Post the SCBID in SINDEX and issue an interrupt */ call add_scb_to_free_list; mov ARG_1, SINDEX; if ((ahc->features & AHC_QUEUE_REGS) != 0) { mov A, SDSCB_QOFF; } else { mov A, QOUTPOS; } mvi QOUTFIFO_OFFSET call post_byte_setup; mov ARG_1 call post_byte; if ((ahc->features & AHC_QUEUE_REGS) == 0) { inc QOUTPOS; } mvi INTSTAT,CMDCMPLT ret; if ((ahc->flags & AHC_INITIATORMODE) != 0) { /* * Is it a disconnect message? Set a flag in the SCB to remind us * and await the bus going free. If this is an untagged transaction * store the SCB id for it in our untagged target table for lookup on * a reselction. */ mesgin_disconnect: or SCB_CONTROL,DISCONNECTED; if ((ahc->flags & AHC_PAGESCBS) != 0) { call add_scb_to_disc_list; } test SCB_CONTROL, TAG_ENB jnz await_busfree; mov ARG_1, SCB_TAG; mov SAVED_LUN, SCB_LUN; mov SCB_SCSIID call index_busy_target; mov DINDIR, ARG_1; jmp await_busfree; /* * Save data pointers message: * Copying RAM values back to SCB, for Save Data Pointers message, but * only if we've actually been into a data phase to change them. This * protects against bogus data in scratch ram and the residual counts * since they are only initialized when we go into data_in or data_out. */ mesgin_sdptrs: test SEQ_FLAGS, DPHASE jz mesgin_done; /* * The SCB_SGPTR becomes the next one we'll download, * and the SCB_DATAPTR becomes the current SHADDR. * Use the residual number since STCNT is corrupted by * any message transfer. */ if ((ahc->features & AHC_CMD_CHAN) != 0) { bmov SCB_DATAPTR, SHADDR, 4; bmov SCB_DATACNT, SCB_RESIDUAL_DATACNT, 8; } else { mvi DINDEX, SCB_DATAPTR; mvi SHADDR call bcopy_4; mvi SCB_RESIDUAL_DATACNT call bcopy_8; } jmp mesgin_done; /* * Restore pointers message? Data pointers are recopied from the * SCB anytime we enter a data phase for the first time, so all * we need to do is clear the DPHASE flag and let the data phase * code do the rest. */ mesgin_rdptrs: and SEQ_FLAGS, ~DPHASE; /* * We'll reload them * the next time through * the dataphase. */ jmp mesgin_done; /* * Index into our Busy Target table. SINDEX and DINDEX are modified * upon return. SCBPTR may be modified by this action. */ index_busy_target: if ((ahc->features & AHC_SCB_BTT) != 0) { mov SCBPTR, SAVED_LUN; add SINDEX, SCB_64_BTT; } else { shr SINDEX, 4; add SINDEX, BUSY_TARGETS; } mov DINDEX, SINDEX ret; /* * Identify message? For a reconnecting target, this tells us the lun * that the reconnection is for - find the correct SCB and switch to it, * clearing the "disconnected" bit so we don't "find" it by accident later. */ mesgin_identify: and SAVED_LUN, MSG_IDENTIFY_LUNMASK, A; /* * Determine whether a target is using tagged or non-tagged * transactions by first looking at the transaction stored in * the busy target array. If there is no untagged transaction * for this target or the transaction is for a different lun, then * this must be an untagged transaction. */ mov SAVED_SCSIID call index_busy_target; mov A, SINDIR; cmp A, SCB_LIST_NULL je snoop_tag; if ((ahc->flags & AHC_PAGESCBS) != 0) { mov A call findSCB; } else { mov SCBPTR, A; } if ((ahc->features & AHC_SCB_BTT) != 0) { jmp setup_SCB_id_lun_okay; } else { mov A, SCB_LUN; cmp SAVED_LUN, A je setup_SCB_id_lun_okay; } /* * Here we "snoop" the bus looking for a SIMPLE QUEUE TAG message. * If we get one, we use the tag returned to find the proper * SCB. With SCB paging, we must search for non-tagged * transactions since the SCB may exist in any slot. If we're not * using SCB paging, we can use the tag as the direct index to the * SCB. */ snoop_tag: mov NONE,SCSIDATL; /* ACK Identify MSG */ snoop_tag_loop: call phase_lock; cmp LASTPHASE, P_MESGIN jne not_found; cmp SCSIBUSL,MSG_SIMPLE_Q_TAG jne not_found; get_tag: if ((ahc->flags & AHC_PAGESCBS) != 0) { mvi ARG_1 call inb_next; /* tag value */ mov ARG_1 call findSCB; } else { mvi SCBPTR call inb_next; /* tag value */ } /* * Ensure that the SCB the tag points to is for * an SCB transaction to the reconnecting target. */ setup_SCB: mov A, SAVED_SCSIID; cmp SCB_SCSIID, A jne not_found; mov A, SAVED_LUN; cmp SCB_LUN, A jne not_found; setup_SCB_id_lun_okay: test SCB_CONTROL,DISCONNECTED jz not_found; if ((ahc->flags & AHC_PAGESCBS) != 0) { mov SCBPTR call rem_scb_from_disc_list; } and SCB_CONTROL,~DISCONNECTED; or SEQ_FLAGS,IDENTIFY_SEEN; /* make note of IDENTIFY */ test SCB_CONTROL, TAG_ENB jnz setup_SCB_tagged; mov A, SCBPTR; mov SAVED_SCSIID call index_busy_target; mvi DINDIR, SCB_LIST_NULL; mov SCBPTR, A; setup_SCB_tagged: call set_transfer_settings; /* See if the host wants to send a message upon reconnection */ test SCB_CONTROL, MK_MESSAGE jz mesgin_done; and SCB_CONTROL, ~MK_MESSAGE; mvi HOST_MSG call mk_mesg; jmp mesgin_done; not_found: mvi INTSTAT, NO_MATCH; jmp mesgin_done; mk_mesg: or SCSISIGO,ATNO,LASTPHASE;/* turn on ATNO */ mov MSG_OUT,SINDEX ret; /* * Functions to read data in Automatic PIO mode. * * According to Adaptec's documentation, an ACK is not sent on input from * the target until SCSIDATL is read from. So we wait until SCSIDATL is * latched (the usual way), then read the data byte directly off the bus * using SCSIBUSL. When we have pulled the ATN line, or we just want to * acknowledge the byte, then we do a dummy read from SCISDATL. The SCSI * spec guarantees that the target will hold the data byte on the bus until * we send our ACK. * * The assumption here is that these are called in a particular sequence, * and that REQ is already set when inb_first is called. inb_{first,next} * use the same calling convention as inb. */ inb_next_wait_perr: mvi INTSTAT, PERR_DETECTED; jmp inb_next_wait; inb_next: mov NONE,SCSIDATL; /*dummy read from latch to ACK*/ inb_next_wait: /* * If there is a parity error, wait for the kernel to * see the interrupt and prepare our message response * before continuing. */ test SSTAT1, REQINIT jz inb_next_wait; test SSTAT1, SCSIPERR jnz inb_next_wait_perr; inb_next_check_phase: and LASTPHASE, PHASE_MASK, SCSISIGI; cmp LASTPHASE, P_MESGIN jne mesgin_phasemis; inb_first: mov DINDEX,SINDEX; mov DINDIR,SCSIBUSL ret; /*read byte directly from bus*/ inb_last: mov NONE,SCSIDATL ret; /*dummy read from latch to ACK*/ } if ((ahc->flags & AHC_TARGETMODE) != 0) { /* * Change to a new phase. If we are changing the state of the I/O signal, * from out to in, wait an additional data release delay before continuing. */ change_phase: /* Wait for preceeding I/O session to complete. */ test SCSISIGI, ACKI jnz .; /* Change the phase */ and DINDEX, IOI, SCSISIGI; mov SCSISIGO, SINDEX; and A, IOI, SINDEX; /* * If the data direction has changed, from * out (initiator driving) to in (target driving), * we must wait at least a data release delay plus * the normal bus settle delay. [SCSI III SPI 10.11.0] */ cmp DINDEX, A je change_phase_wait; test SINDEX, IOI jz change_phase_wait; call change_phase_wait; change_phase_wait: nop; nop; nop; nop ret; /* * Send a byte to an initiator in Automatic PIO mode. */ target_outb: or SXFRCTL0, SPIOEN; test SSTAT0, SPIORDY jz .; mov SCSIDATL, SINDEX; test SSTAT0, SPIORDY jz .; and SXFRCTL0, ~SPIOEN ret; } /* * Assert that if we've been reselected, then we've seen an IDENTIFY * message. */ assert: test SEQ_FLAGS,IDENTIFY_SEEN jnz return; /* seen IDENTIFY? */ mvi INTSTAT,NO_IDENT ret; /* no - tell the kernel */ /* * Locate a disconnected SCB by SCBID. Upon return, SCBPTR and SINDEX will * be set to the position of the SCB. If the SCB cannot be found locally, * it will be paged in from host memory. RETURN_2 stores the address of the * preceding SCB in the disconnected list which can be used to speed up * removal of the found SCB from the disconnected list. */ findSCB: mov SCBPTR, DISCONNECTED_SCBH; /* Initialize SCBPTR */ mov A, SINDEX; /* Tag passed in SINDEX */ mvi RETURN_2, SCB_LIST_NULL; /* Head of list */ jmp findSCB_loop; findSCB_next: mov RETURN_2, SCBPTR; cmp SCB_NEXT, SCB_LIST_NULL je findSCB_notFound; mov SCBPTR,SCB_NEXT; findSCB_loop: cmp SCB_TAG, A jne findSCB_next; mov SINDEX, SCBPTR ret; findSCB_notFound: /* * We didn't find it. Page in the SCB and make it look * like it was at the head of the appropriate scb list. */ mov ARG_1, A; /* Save tag */ mov ALLZEROS call get_free_or_disc_scb; mvi DMAPARAMS, HDMAEN|DIRECTION|FIFORESET; mov ARG_1 call dma_scb; mvi RETURN_2, SCB_LIST_NULL; /* Head of list */ /* Jump instead of call as we want to return anyway */ test SCB_CONTROL, DISCONNECTED jnz add_scb_to_disc_list; jmp add_scb_to_free_list; /* * This routine expects SINDEX to contain the index of the SCB to be * removed, SCBPTR to be pointing to that SCB, and ARG_2 to be the * SCBID of the SCB just previous to this one in the list or SCB_LIST_NULL * if it is at the head. */ rem_scb_from_disc_list: /* Remove this SCB from the disconnection list */ cmp ARG_2, SCB_LIST_NULL je rHead; mov DINDEX, SCB_NEXT; mov SCBPTR, ARG_2; mov SCB_NEXT, DINDEX; mov SCBPTR, SINDEX ret; rHead: mov DISCONNECTED_SCBH,SCB_NEXT ret; /* * Fetch a byte from host memory given an index of (A + (256 * SINDEX)) * and a base address of SHARED_DATA_ADDR. The byte is returned in RETURN_2. */ fetch_byte: mov ARG_2, SINDEX; if ((ahc->features & AHC_CMD_CHAN) != 0) { mvi DINDEX, CCHADDR; mvi SHARED_DATA_ADDR call set_1byte_addr; mvi CCHCNT, 1; mvi CCSGCTL, CCSGEN|CCSGRESET; test CCSGCTL, CCSGDONE jz .; mvi CCSGCTL, CCSGRESET; bmov RETURN_2, CCSGRAM, 1 ret; } else { mvi DINDEX, HADDR; mvi SHARED_DATA_ADDR call set_1byte_addr; mvi 1 call set_hcnt; mvi DFCNTRL, HDMAEN|DIRECTION|FIFORESET; call dma_finish; mov RETURN_2, DFDAT ret; } /* * Prepare the hardware to post a byte to host memory given an * index of (A + (256 * SINDEX)) and a base address of SHARED_DATA_ADDR. */ post_byte_setup: mov ARG_2, SINDEX; if ((ahc->features & AHC_CMD_CHAN) != 0) { mvi DINDEX, CCHADDR; mvi SHARED_DATA_ADDR call set_1byte_addr; mvi CCHCNT, 1; mvi CCSCBCTL, CCSCBRESET ret; } else { mvi DINDEX, HADDR; mvi SHARED_DATA_ADDR call set_1byte_addr; mvi 1 call set_hcnt; mvi DFCNTRL, FIFORESET ret; } post_byte: if ((ahc->features & AHC_CMD_CHAN) != 0) { bmov CCSCBRAM, SINDEX, 1; or CCSCBCTL, CCSCBEN|CCSCBRESET; test CCSCBCTL, CCSCBDONE jz .; clr CCSCBCTL ret; } else { mov DFDAT, SINDEX; or DFCNTRL, HDMAEN|FIFOFLUSH; jmp dma_finish; } get_SCBID_from_host: mov A, SAVED_LUN; shr SINDEX, 4, SAVED_SCSIID; call fetch_byte; mov RETURN_1, RETURN_2 ret; phase_lock_perr: mvi INTSTAT, PERR_DETECTED; phase_lock: /* * If there is a parity error, wait for the kernel to * see the interrupt and prepare our message response * before continuing. */ test SSTAT1, REQINIT jz phase_lock; test SSTAT1, SCSIPERR jnz phase_lock_perr; phase_lock_latch_phase: and SCSISIGO, PHASE_MASK, SCSISIGI; and LASTPHASE, PHASE_MASK, SCSISIGI ret; if ((ahc->features & AHC_CMD_CHAN) == 0) { set_hcnt: mov HCNT[0], SINDEX; clear_hcnt: clr HCNT[1]; clr HCNT[2] ret; set_stcnt_from_hcnt: mov STCNT[0], HCNT[0]; mov STCNT[1], HCNT[1]; mov STCNT[2], HCNT[2] ret; bcopy_8: mov DINDIR, SINDIR; bcopy_7: mov DINDIR, SINDIR; mov DINDIR, SINDIR; bcopy_5: mov DINDIR, SINDIR; bcopy_4: mov DINDIR, SINDIR; bcopy_3: mov DINDIR, SINDIR; mov DINDIR, SINDIR; mov DINDIR, SINDIR ret; } if ((ahc->flags & AHC_TARGETMODE) != 0) { /* * Setup addr assuming that A is an index into * an array of 32byte objects, SINDEX contains * the base address of that array, and DINDEX * contains the base address of the location * to store the indexed address. */ set_32byte_addr: shr ARG_2, 3, A; shl A, 5; jmp set_1byte_addr; } /* * Setup addr assuming that A is an index into * an array of 64byte objects, SINDEX contains * the base address of that array, and DINDEX * contains the base address of the location * to store the indexed address. */ set_64byte_addr: shr ARG_2, 2, A; shl A, 6; /* * Setup addr assuming that A + (ARG_2 * 256) is an * index into an array of 1byte objects, SINDEX contains * the base address of that array, and DINDEX contains * the base address of the location to store the computed * address. */ set_1byte_addr: add DINDIR, A, SINDIR; mov A, ARG_2; adc DINDIR, A, SINDIR; clr A; adc DINDIR, A, SINDIR; adc DINDIR, A, SINDIR ret; /* * Either post or fetch and SCB from host memory based on the * DIRECTION bit in DMAPARAMS. The host SCB index is in SINDEX. */ dma_scb: mov A, SINDEX; if ((ahc->features & AHC_CMD_CHAN) != 0) { mvi DINDEX, CCHADDR; mvi HSCB_ADDR call set_64byte_addr; mov CCSCBPTR, SCBPTR; test DMAPARAMS, DIRECTION jz dma_scb_tohost; mvi CCHCNT, SCB_64BYTE_SIZE; mvi CCSCBCTL, CCARREN|CCSCBEN|CCSCBDIR|CCSCBRESET; cmp CCSCBCTL, CCSCBDONE|ARRDONE|CCARREN|CCSCBEN|CCSCBDIR jne .; jmp dma_scb_finish; dma_scb_tohost: mvi CCHCNT, SCB_32BYTE_SIZE; if ((ahc->chip & AHC_CHIPID_MASK) == AHC_AIC7895) { mvi CCSCBCTL, CCSCBRESET; bmov CCSCBRAM, SCB_CONTROL, SCB_32BYTE_SIZE; or CCSCBCTL, CCSCBEN|CCSCBRESET; test CCSCBCTL, CCSCBDONE jz .; } else { mvi CCSCBCTL, CCARREN|CCSCBEN|CCSCBRESET; cmp CCSCBCTL, CCSCBDONE|ARRDONE|CCARREN|CCSCBEN jne .; } dma_scb_finish: clr CCSCBCTL; test CCSCBCTL, CCARREN|CCSCBEN jnz .; ret; } else { mvi DINDEX, HADDR; mvi HSCB_ADDR call set_64byte_addr; mvi SCB_32BYTE_SIZE call set_hcnt; mov DFCNTRL, DMAPARAMS; test DMAPARAMS, DIRECTION jnz dma_scb_fromhost; /* Fill it with the SCB data */ copy_scb_tofifo: mvi SINDEX, SCB_CONTROL; add A, SCB_32BYTE_SIZE, SINDEX; copy_scb_tofifo_loop: call copy_to_fifo_6; cmp SINDEX, A jne copy_scb_tofifo_loop; or DFCNTRL, HDMAEN|FIFOFLUSH; dma_scb_fromhost: call dma_finish; /* If we were putting the SCB, we are done */ test DMAPARAMS, DIRECTION jz return; mvi SCB_CONTROL call dfdat_in_7; call dfdat_in_7_continued; call dfdat_in_7_continued; call dfdat_in_7_continued; jmp dfdat_in_2_continued; dfdat_in_7: mov DINDEX,SINDEX; dfdat_in_7_continued: mov DINDIR,DFDAT; mov DINDIR,DFDAT; mov DINDIR,DFDAT; mov DINDIR,DFDAT; mov DINDIR,DFDAT; dfdat_in_2_continued: mov DINDIR,DFDAT; mov DINDIR,DFDAT ret; } copy_to_fifo_8: mov DFDAT,SINDIR; copy_to_fifo_7: mov DFDAT,SINDIR; copy_to_fifo_6: mov DFDAT,SINDIR; copy_to_fifo_5: mov DFDAT,SINDIR; copy_to_fifo_4: mov DFDAT,SINDIR; mov DFDAT,SINDIR; mov DFDAT,SINDIR; mov DFDAT,SINDIR ret; /* * Wait for DMA from host memory to data FIFO to complete, then disable * DMA and wait for it to acknowledge that it's off. */ dma_finish: test DFSTATUS,HDONE jz dma_finish; /* Turn off DMA */ and DFCNTRL, ~HDMAEN; test DFCNTRL, HDMAEN jnz .; ret; add_scb_to_free_list: if ((ahc->flags & AHC_PAGESCBS) != 0) { mov SCB_NEXT, FREE_SCBH; mvi SCB_TAG, SCB_LIST_NULL; mov FREE_SCBH, SCBPTR ret; } else { mvi SCB_TAG, SCB_LIST_NULL ret; } if ((ahc->flags & AHC_PAGESCBS) != 0) { get_free_or_disc_scb: cmp FREE_SCBH, SCB_LIST_NULL jne dequeue_free_scb; cmp DISCONNECTED_SCBH, SCB_LIST_NULL jne dequeue_disc_scb; return_error: mvi SINDEX, SCB_LIST_NULL ret; dequeue_disc_scb: mov SCBPTR, DISCONNECTED_SCBH; dma_up_scb: mvi DMAPARAMS, FIFORESET; mov SCB_TAG call dma_scb; unlink_disc_scb: mov DISCONNECTED_SCBH, SCB_NEXT ret; dequeue_free_scb: mov SCBPTR, FREE_SCBH; mov FREE_SCBH, SCB_NEXT ret; } add_scb_to_disc_list: /* * Link this SCB into the DISCONNECTED list. This list holds the * candidates for paging out an SCB if one is needed for a new command. * Modifying the disconnected list is a critical(pause dissabled) section. */ mov SCB_NEXT, DISCONNECTED_SCBH; mov DISCONNECTED_SCBH, SCBPTR ret; return: ret;