freebsd-skq/sys/dev/ath/if_ath_rx_edma.c
Adrian Chadd a100c050eb [ath] Hopefully recover better-er upon RX restart on AR9380.
This is all very long-standing bug stuff that is touchy and still poorly
documented. Ok, here goes.

The basic bug:

* deleting a VAP causes the RX path (and TX path too) to be restarted
  without a full chip reset, which causes RX hangs on the AR9380 and later.
  (ie, the ones with the newer DMA engine.)

The basic fix:

* do an RX flush when stopping RX in ath_vap_delete() to match what happens
  when RX is stopped elsewhere.  This ensures any pending frames are completed
  and we restart at the right spot; it also ensures we don't push new RX buffers
  into the hardware if we're stopping receive.

The other issues I found:

* Don't bother checking the RX packet ring in the deferred read taskqueue;
  that's specifically supposed to be for completing frames rather than
  just yanking them off the receive ring.

* Cancel/drain any pending deferred read taskqueue.  This isn't done inside
  any locks so we should be super careful here.  This stops the hardware
  being reprogrammed at the same time in another thread/CPU whilst we're
  stopping RX.

* .. (yes, this should be better serialised, but that's for another day. maybe.)

* Add more debugging to trace what's going on here.

And the fun bit:

* Reinitialise the RX FIFO ONLY if we've been reset or stopped, rather than just
  reset.  I noticed that after all the above was done I was STILL seeing RXEOL.
  RXEOL isn't enabled on the AR9380 so I'd only see it if I was sending TX frames
  (ie a ping where it'd be transmitted but never received) so I was not being
  spammed by RXEOL.  So, as long as stuff is stopped, restart it.

This seems to be doing the right thing in both AP and STA modes.

What I should do next, if I ever get time:

* as I said above, serialise the receive stop/start to include taskqueues
* monitor RXEOL on the AR9380 and I keep seeing it spammed / lockups, just
  go do a full chip reset to get things back on track. It sucks, but it
  is better than nothing.

Tested:

* AR9380 AP/STA mode, adding/deleting a hostap VAP to trigger the TX/RX
  queue stop/start; whilst also running an iperf through it.  Lots of times.
  Lots.  Of.. Times.
2020-05-21 04:35:12 +00:00

1050 lines
25 KiB
C

/*-
* SPDX-License-Identifier: BSD-2-Clause-FreeBSD
*
* Copyright (c) 2012 Adrian Chadd <adrian@FreeBSD.org>
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer,
* without modification.
* 2. Redistributions in binary form must reproduce at minimum a disclaimer
* similar to the "NO WARRANTY" disclaimer below ("Disclaimer") and any
* redistribution must be conditioned upon including a substantially
* similar Disclaimer requirement for further binary redistribution.
*
* NO WARRANTY
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTIBILITY
* AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
* THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY,
* OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
* IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
* THE POSSIBILITY OF SUCH DAMAGES.
*/
#include <sys/cdefs.h>
__FBSDID("$FreeBSD$");
/*
* Driver for the Atheros Wireless LAN controller.
*
* This software is derived from work of Atsushi Onoe; his contribution
* is greatly appreciated.
*/
#include "opt_inet.h"
#include "opt_ath.h"
/*
* This is needed for register operations which are performed
* by the driver - eg, calls to ath_hal_gettsf32().
*
* It's also required for any AH_DEBUG checks in here, eg the
* module dependencies.
*/
#include "opt_ah.h"
#include "opt_wlan.h"
#include <sys/param.h>
#include <sys/systm.h>
#include <sys/sysctl.h>
#include <sys/mbuf.h>
#include <sys/malloc.h>
#include <sys/lock.h>
#include <sys/mutex.h>
#include <sys/kernel.h>
#include <sys/socket.h>
#include <sys/sockio.h>
#include <sys/errno.h>
#include <sys/callout.h>
#include <sys/bus.h>
#include <sys/endian.h>
#include <sys/kthread.h>
#include <sys/taskqueue.h>
#include <sys/priv.h>
#include <sys/module.h>
#include <sys/ktr.h>
#include <sys/smp.h> /* for mp_ncpus */
#include <machine/bus.h>
#include <net/if.h>
#include <net/if_var.h>
#include <net/if_dl.h>
#include <net/if_media.h>
#include <net/if_types.h>
#include <net/if_arp.h>
#include <net/ethernet.h>
#include <net/if_llc.h>
#include <net80211/ieee80211_var.h>
#include <net80211/ieee80211_regdomain.h>
#ifdef IEEE80211_SUPPORT_SUPERG
#include <net80211/ieee80211_superg.h>
#endif
#ifdef IEEE80211_SUPPORT_TDMA
#include <net80211/ieee80211_tdma.h>
#endif
#include <net/bpf.h>
#ifdef INET
#include <netinet/in.h>
#include <netinet/if_ether.h>
#endif
#include <dev/ath/if_athvar.h>
#include <dev/ath/ath_hal/ah_devid.h> /* XXX for softled */
#include <dev/ath/ath_hal/ah_diagcodes.h>
#include <dev/ath/if_ath_debug.h>
#include <dev/ath/if_ath_misc.h>
#include <dev/ath/if_ath_tsf.h>
#include <dev/ath/if_ath_tx.h>
#include <dev/ath/if_ath_sysctl.h>
#include <dev/ath/if_ath_led.h>
#include <dev/ath/if_ath_keycache.h>
#include <dev/ath/if_ath_rx.h>
#include <dev/ath/if_ath_beacon.h>
#include <dev/ath/if_athdfs.h>
#include <dev/ath/if_ath_descdma.h>
#ifdef ATH_TX99_DIAG
#include <dev/ath/ath_tx99/ath_tx99.h>
#endif
#include <dev/ath/if_ath_rx_edma.h>
#ifdef ATH_DEBUG_ALQ
#include <dev/ath/if_ath_alq.h>
#endif
/*
* some general macros
*/
#define INCR(_l, _sz) (_l) ++; (_l) &= ((_sz) - 1)
#define DECR(_l, _sz) (_l) --; (_l) &= ((_sz) - 1)
MALLOC_DECLARE(M_ATHDEV);
/*
* XXX TODO:
*
* + Make sure the FIFO is correctly flushed and reinitialised
* through a reset;
* + Verify multi-descriptor frames work!
* + There's a "memory use after free" which needs to be tracked down
* and fixed ASAP. I've seen this in the legacy path too, so it
* may be a generic RX path issue.
*/
/*
* XXX shuffle the function orders so these pre-declarations aren't
* required!
*/
static int ath_edma_rxfifo_alloc(struct ath_softc *sc, HAL_RX_QUEUE qtype,
int nbufs);
static int ath_edma_rxfifo_flush(struct ath_softc *sc, HAL_RX_QUEUE qtype);
static void ath_edma_rxbuf_free(struct ath_softc *sc, struct ath_buf *bf);
static void ath_edma_recv_proc_queue(struct ath_softc *sc,
HAL_RX_QUEUE qtype, int dosched);
static int ath_edma_recv_proc_deferred_queue(struct ath_softc *sc,
HAL_RX_QUEUE qtype, int dosched);
static void
ath_edma_stoprecv(struct ath_softc *sc, int dodelay)
{
struct ath_hal *ah = sc->sc_ah;
DPRINTF(sc, ATH_DEBUG_EDMA_RX, "%s: called, dodelay=%d\n",
__func__, dodelay);
ATH_RX_LOCK(sc);
ath_hal_stoppcurecv(ah);
ath_hal_setrxfilter(ah, 0);
/*
*
*/
if (ath_hal_stopdmarecv(ah) == AH_TRUE)
sc->sc_rx_stopped = 1;
/*
* Give the various bus FIFOs (not EDMA descriptor FIFO)
* time to finish flushing out data.
*/
DELAY(3000);
/* Flush RX pending for each queue */
/* XXX should generic-ify this */
if (sc->sc_rxedma[HAL_RX_QUEUE_HP].m_rxpending) {
m_freem(sc->sc_rxedma[HAL_RX_QUEUE_HP].m_rxpending);
sc->sc_rxedma[HAL_RX_QUEUE_HP].m_rxpending = NULL;
}
if (sc->sc_rxedma[HAL_RX_QUEUE_LP].m_rxpending) {
m_freem(sc->sc_rxedma[HAL_RX_QUEUE_LP].m_rxpending);
sc->sc_rxedma[HAL_RX_QUEUE_LP].m_rxpending = NULL;
}
ATH_RX_UNLOCK(sc);
DPRINTF(sc, ATH_DEBUG_EDMA_RX, "%s: done\n", __func__);
}
/*
* Re-initialise the FIFO given the current buffer contents.
* Specifically, walk from head -> tail, pushing the FIFO contents
* back into the FIFO.
*/
static void
ath_edma_reinit_fifo(struct ath_softc *sc, HAL_RX_QUEUE qtype)
{
struct ath_rx_edma *re = &sc->sc_rxedma[qtype];
struct ath_buf *bf;
int i, j;
DPRINTF(sc, ATH_DEBUG_EDMA_RX, "%s: called\n", __func__);
ATH_RX_LOCK_ASSERT(sc);
i = re->m_fifo_head;
for (j = 0; j < re->m_fifo_depth; j++) {
bf = re->m_fifo[i];
DPRINTF(sc, ATH_DEBUG_EDMA_RX,
"%s: Q%d: pos=%i, addr=0x%jx\n",
__func__,
qtype,
i,
(uintmax_t)bf->bf_daddr);
ath_hal_putrxbuf(sc->sc_ah, bf->bf_daddr, qtype);
INCR(i, re->m_fifolen);
}
/* Ensure this worked out right */
if (i != re->m_fifo_tail) {
device_printf(sc->sc_dev, "%s: i (%d) != tail! (%d)\n",
__func__,
i,
re->m_fifo_tail);
}
DPRINTF(sc, ATH_DEBUG_EDMA_RX, "%s: done\n", __func__);
}
/*
* Start receive.
*/
static int
ath_edma_startrecv(struct ath_softc *sc)
{
struct ath_hal *ah = sc->sc_ah;
DPRINTF(sc, ATH_DEBUG_EDMA_RX,
"%s: called; resetted=%d, stopped=%d\n", __func__,
sc->sc_rx_resetted, sc->sc_rx_stopped);
ATH_RX_LOCK(sc);
/*
* Sanity check - are we being called whilst RX
* isn't stopped? If so, we may end up pushing
* too many entries into the RX FIFO and
* badness occurs.
*/
/* Enable RX FIFO */
ath_hal_rxena(ah);
/*
* In theory the hardware has been initialised, right?
*/
if (sc->sc_rx_resetted == 1 || sc->sc_rx_stopped == 1) {
DPRINTF(sc, ATH_DEBUG_EDMA_RX,
"%s: Re-initing HP FIFO\n", __func__);
ath_edma_reinit_fifo(sc, HAL_RX_QUEUE_HP);
DPRINTF(sc, ATH_DEBUG_EDMA_RX,
"%s: Re-initing LP FIFO\n", __func__);
ath_edma_reinit_fifo(sc, HAL_RX_QUEUE_LP);
sc->sc_rx_resetted = 0;
} else {
device_printf(sc->sc_dev,
"%s: called without resetting chip? "
"resetted=%d, stopped=%d\n",
__func__,
sc->sc_rx_resetted,
sc->sc_rx_stopped);
}
/* Add up to m_fifolen entries in each queue */
/*
* These must occur after the above write so the FIFO buffers
* are pushed/tracked in the same order as the hardware will
* process them.
*
* XXX TODO: is this really necessary? We should've stopped
* the hardware already and reinitialised it, so it's a no-op.
*/
ath_edma_rxfifo_alloc(sc, HAL_RX_QUEUE_HP,
sc->sc_rxedma[HAL_RX_QUEUE_HP].m_fifolen);
ath_edma_rxfifo_alloc(sc, HAL_RX_QUEUE_LP,
sc->sc_rxedma[HAL_RX_QUEUE_LP].m_fifolen);
ath_mode_init(sc);
ath_hal_startpcurecv(ah, (!! sc->sc_scanning));
/*
* We're now doing RX DMA!
*/
sc->sc_rx_stopped = 0;
ATH_RX_UNLOCK(sc);
DPRINTF(sc, ATH_DEBUG_EDMA_RX, "%s: ready\n", __func__);
return (0);
}
static void
ath_edma_recv_sched_queue(struct ath_softc *sc, HAL_RX_QUEUE qtype,
int dosched)
{
DPRINTF(sc, ATH_DEBUG_EDMA_RX, "%s: called; qtype=%d, dosched=%d\n",
__func__, qtype, dosched);
ATH_LOCK(sc);
ath_power_set_power_state(sc, HAL_PM_AWAKE);
ATH_UNLOCK(sc);
ath_edma_recv_proc_queue(sc, qtype, dosched);
ATH_LOCK(sc);
ath_power_restore_power_state(sc);
ATH_UNLOCK(sc);
/* XXX TODO: methodize */
taskqueue_enqueue(sc->sc_tq, &sc->sc_rxtask);
DPRINTF(sc, ATH_DEBUG_EDMA_RX, "%s: done\n", __func__);
}
static void
ath_edma_recv_sched(struct ath_softc *sc, int dosched)
{
DPRINTF(sc, ATH_DEBUG_EDMA_RX, "%s: called; dosched=%d\n",
__func__, dosched);
ATH_LOCK(sc);
ath_power_set_power_state(sc, HAL_PM_AWAKE);
ATH_UNLOCK(sc);
ath_edma_recv_proc_queue(sc, HAL_RX_QUEUE_HP, dosched);
ath_edma_recv_proc_queue(sc, HAL_RX_QUEUE_LP, dosched);
ATH_LOCK(sc);
ath_power_restore_power_state(sc);
ATH_UNLOCK(sc);
/* XXX TODO: methodize */
taskqueue_enqueue(sc->sc_tq, &sc->sc_rxtask);
DPRINTF(sc, ATH_DEBUG_EDMA_RX, "%s: done\n", __func__);
}
static void
ath_edma_recv_flush(struct ath_softc *sc)
{
DPRINTF(sc, ATH_DEBUG_RECV | ATH_DEBUG_EDMA_RX, "%s: called\n", __func__);
ATH_PCU_LOCK(sc);
sc->sc_rxproc_cnt++;
ATH_PCU_UNLOCK(sc);
// XXX TODO: methodize; make it an RX stop/block
while (taskqueue_cancel(sc->sc_tq, &sc->sc_rxtask, NULL) != 0) {
taskqueue_drain(sc->sc_tq, &sc->sc_rxtask);
}
ATH_LOCK(sc);
ath_power_set_power_state(sc, HAL_PM_AWAKE);
ATH_UNLOCK(sc);
/*
* Flush any active frames from FIFO -> deferred list
*/
ath_edma_recv_proc_queue(sc, HAL_RX_QUEUE_HP, 0);
ath_edma_recv_proc_queue(sc, HAL_RX_QUEUE_LP, 0);
/*
* Process what's in the deferred queue
*/
/*
* XXX: If we read the tsf/channoise here and then pass it in,
* we could restore the power state before processing
* the deferred queue.
*/
ath_edma_recv_proc_deferred_queue(sc, HAL_RX_QUEUE_HP, 0);
ath_edma_recv_proc_deferred_queue(sc, HAL_RX_QUEUE_LP, 0);
ATH_LOCK(sc);
ath_power_restore_power_state(sc);
ATH_UNLOCK(sc);
ATH_PCU_LOCK(sc);
sc->sc_rxproc_cnt--;
ATH_PCU_UNLOCK(sc);
DPRINTF(sc, ATH_DEBUG_RECV | ATH_DEBUG_EDMA_RX, "%s: done\n", __func__);
}
/*
* Process frames from the current queue into the deferred queue.
*/
static void
ath_edma_recv_proc_queue(struct ath_softc *sc, HAL_RX_QUEUE qtype,
int dosched)
{
struct ath_rx_edma *re = &sc->sc_rxedma[qtype];
struct ath_rx_status *rs;
struct ath_desc *ds;
struct ath_buf *bf;
struct mbuf *m;
struct ath_hal *ah = sc->sc_ah;
uint64_t tsf;
uint16_t nf;
int npkts = 0;
tsf = ath_hal_gettsf64(ah);
nf = ath_hal_getchannoise(ah, sc->sc_curchan);
sc->sc_stats.ast_rx_noise = nf;
DPRINTF(sc, ATH_DEBUG_EDMA_RX, "%s: called; qtype=%d, dosched=%d\n", __func__, qtype, dosched);
ATH_RX_LOCK(sc);
#if 1
if (sc->sc_rx_resetted == 1) {
/*
* XXX We shouldn't ever be scheduled if
* receive has been stopped - so complain
* loudly!
*/
device_printf(sc->sc_dev,
"%s: sc_rx_resetted=1! Bad!\n",
__func__);
ATH_RX_UNLOCK(sc);
return;
}
#endif
do {
bf = re->m_fifo[re->m_fifo_head];
/* This shouldn't occur! */
if (bf == NULL) {
device_printf(sc->sc_dev, "%s: Q%d: NULL bf?\n",
__func__,
qtype);
break;
}
m = bf->bf_m;
ds = bf->bf_desc;
/*
* Sync descriptor memory - this also syncs the buffer for us.
* EDMA descriptors are in cached memory.
*/
bus_dmamap_sync(sc->sc_dmat, bf->bf_dmamap,
BUS_DMASYNC_POSTREAD | BUS_DMASYNC_POSTWRITE);
rs = &bf->bf_status.ds_rxstat;
bf->bf_rxstatus = ath_hal_rxprocdesc(ah, ds, bf->bf_daddr,
NULL, rs);
if (bf->bf_rxstatus == HAL_EINPROGRESS)
break;
#ifdef ATH_DEBUG
if (sc->sc_debug & ATH_DEBUG_RECV_DESC)
ath_printrxbuf(sc, bf, 0, bf->bf_rxstatus == HAL_OK);
#endif /* ATH_DEBUG */
#ifdef ATH_DEBUG_ALQ
if (if_ath_alq_checkdebug(&sc->sc_alq, ATH_ALQ_EDMA_RXSTATUS))
if_ath_alq_post(&sc->sc_alq, ATH_ALQ_EDMA_RXSTATUS,
sc->sc_rx_statuslen, (char *) ds);
#endif /* ATH_DEBUG */
/*
* Completed descriptor.
*/
DPRINTF(sc, ATH_DEBUG_EDMA_RX,
"%s: Q%d: completed!\n", __func__, qtype);
npkts++;
/*
* We've been synced already, so unmap.
*/
bus_dmamap_unload(sc->sc_dmat, bf->bf_dmamap);
/*
* Remove the FIFO entry and place it on the completion
* queue.
*/
re->m_fifo[re->m_fifo_head] = NULL;
TAILQ_INSERT_TAIL(&sc->sc_rx_rxlist[qtype], bf, bf_list);
/* Bump the descriptor FIFO stats */
INCR(re->m_fifo_head, re->m_fifolen);
re->m_fifo_depth--;
/* XXX check it doesn't fall below 0 */
} while (re->m_fifo_depth > 0);
/* Append some more fresh frames to the FIFO */
if (dosched)
ath_edma_rxfifo_alloc(sc, qtype, re->m_fifolen);
ATH_RX_UNLOCK(sc);
/* rx signal state monitoring */
ath_hal_rxmonitor(ah, &sc->sc_halstats, sc->sc_curchan);
ATH_KTR(sc, ATH_KTR_INTERRUPTS, 1,
"ath edma rx proc: npkts=%d\n",
npkts);
return;
}
/*
* Flush the deferred queue.
*
* This destructively flushes the deferred queue - it doesn't
* call the wireless stack on each mbuf.
*/
static void
ath_edma_flush_deferred_queue(struct ath_softc *sc)
{
struct ath_buf *bf;
ATH_RX_LOCK_ASSERT(sc);
/* Free in one set, inside the lock */
while (! TAILQ_EMPTY(&sc->sc_rx_rxlist[HAL_RX_QUEUE_LP])) {
bf = TAILQ_FIRST(&sc->sc_rx_rxlist[HAL_RX_QUEUE_LP]);
TAILQ_REMOVE(&sc->sc_rx_rxlist[HAL_RX_QUEUE_LP], bf, bf_list);
/* Free the buffer/mbuf */
ath_edma_rxbuf_free(sc, bf);
}
while (! TAILQ_EMPTY(&sc->sc_rx_rxlist[HAL_RX_QUEUE_HP])) {
bf = TAILQ_FIRST(&sc->sc_rx_rxlist[HAL_RX_QUEUE_HP]);
TAILQ_REMOVE(&sc->sc_rx_rxlist[HAL_RX_QUEUE_HP], bf, bf_list);
/* Free the buffer/mbuf */
ath_edma_rxbuf_free(sc, bf);
}
}
static int
ath_edma_recv_proc_deferred_queue(struct ath_softc *sc, HAL_RX_QUEUE qtype,
int dosched)
{
int ngood = 0;
uint64_t tsf;
struct ath_buf *bf, *next;
struct ath_rx_status *rs;
int16_t nf;
ath_bufhead rxlist;
struct mbuf *m;
struct epoch_tracker et;
TAILQ_INIT(&rxlist);
nf = ath_hal_getchannoise(sc->sc_ah, sc->sc_curchan);
/*
* XXX TODO: the NF/TSF should be stamped on the bufs themselves,
* otherwise we may end up adding in the wrong values if this
* is delayed too far..
*/
tsf = ath_hal_gettsf64(sc->sc_ah);
/* Copy the list over */
ATH_RX_LOCK(sc);
TAILQ_CONCAT(&rxlist, &sc->sc_rx_rxlist[qtype], bf_list);
ATH_RX_UNLOCK(sc);
NET_EPOCH_ENTER(et);
/* Handle the completed descriptors */
/*
* XXX is this SAFE call needed? The ath_buf entries
* aren't modified by ath_rx_pkt, right?
*/
TAILQ_FOREACH_SAFE(bf, &rxlist, bf_list, next) {
/*
* Skip the RX descriptor status - start at the data offset
*/
m_adj(bf->bf_m, sc->sc_rx_statuslen);
/* Handle the frame */
rs = &bf->bf_status.ds_rxstat;
m = bf->bf_m;
bf->bf_m = NULL;
if (ath_rx_pkt(sc, rs, bf->bf_rxstatus, tsf, nf, qtype, bf, m))
ngood++;
}
if (ngood) {
sc->sc_lastrx = tsf;
}
NET_EPOCH_EXIT(et);
ATH_KTR(sc, ATH_KTR_INTERRUPTS, 1,
"ath edma rx deferred proc: ngood=%d\n",
ngood);
/* Free in one set, inside the lock */
ATH_RX_LOCK(sc);
while (! TAILQ_EMPTY(&rxlist)) {
bf = TAILQ_FIRST(&rxlist);
TAILQ_REMOVE(&rxlist, bf, bf_list);
/* Free the buffer/mbuf */
ath_edma_rxbuf_free(sc, bf);
}
ATH_RX_UNLOCK(sc);
return (ngood);
}
static void
ath_edma_recv_tasklet(void *arg, int npending)
{
struct ath_softc *sc = (struct ath_softc *) arg;
#ifdef IEEE80211_SUPPORT_SUPERG
struct ieee80211com *ic = &sc->sc_ic;
#endif
DPRINTF(sc, ATH_DEBUG_EDMA_RX, "%s: called; npending=%d\n",
__func__,
npending);
ATH_PCU_LOCK(sc);
if (sc->sc_inreset_cnt > 0) {
device_printf(sc->sc_dev, "%s: sc_inreset_cnt > 0; skipping\n",
__func__);
ATH_PCU_UNLOCK(sc);
return;
}
sc->sc_rxproc_cnt++;
ATH_PCU_UNLOCK(sc);
ATH_LOCK(sc);
ath_power_set_power_state(sc, HAL_PM_AWAKE);
ATH_UNLOCK(sc);
ath_edma_recv_proc_deferred_queue(sc, HAL_RX_QUEUE_HP, 1);
ath_edma_recv_proc_deferred_queue(sc, HAL_RX_QUEUE_LP, 1);
/*
* XXX: If we read the tsf/channoise here and then pass it in,
* we could restore the power state before processing
* the deferred queue.
*/
ATH_LOCK(sc);
ath_power_restore_power_state(sc);
ATH_UNLOCK(sc);
#ifdef IEEE80211_SUPPORT_SUPERG
ieee80211_ff_age_all(ic, 100);
#endif
if (ath_dfs_tasklet_needed(sc, sc->sc_curchan))
taskqueue_enqueue(sc->sc_tq, &sc->sc_dfstask);
ATH_PCU_LOCK(sc);
sc->sc_rxproc_cnt--;
ATH_PCU_UNLOCK(sc);
DPRINTF(sc, ATH_DEBUG_EDMA_RX, "%s: called; done!\n", __func__);
}
/*
* Allocate an RX mbuf for the given ath_buf and initialise
* it for EDMA.
*
* + Allocate a 4KB mbuf;
* + Setup the DMA map for the given buffer;
* + Return that.
*/
static int
ath_edma_rxbuf_init(struct ath_softc *sc, struct ath_buf *bf)
{
struct mbuf *m;
int error;
int len;
ATH_RX_LOCK_ASSERT(sc);
m = m_getm(NULL, sc->sc_edma_bufsize, M_NOWAIT, MT_DATA);
if (! m)
return (ENOBUFS); /* XXX ?*/
/* XXX warn/enforce alignment */
len = m->m_ext.ext_size;
#if 0
device_printf(sc->sc_dev, "%s: called: m=%p, size=%d, mtod=%p\n",
__func__,
m,
len,
mtod(m, char *));
#endif
m->m_pkthdr.len = m->m_len = m->m_ext.ext_size;
/*
* Populate ath_buf fields.
*/
bf->bf_desc = mtod(m, struct ath_desc *);
bf->bf_lastds = bf->bf_desc; /* XXX only really for TX? */
bf->bf_m = m;
/*
* Zero the descriptor and ensure it makes it out to the
* bounce buffer if one is required.
*
* XXX PREWRITE will copy the whole buffer; we only needed it
* to sync the first 32 DWORDS. Oh well.
*/
memset(bf->bf_desc, '\0', sc->sc_rx_statuslen);
/*
* Create DMA mapping.
*/
error = bus_dmamap_load_mbuf_sg(sc->sc_dmat,
bf->bf_dmamap, m, bf->bf_segs, &bf->bf_nseg, BUS_DMA_NOWAIT);
if (error != 0) {
device_printf(sc->sc_dev, "%s: failed; error=%d\n",
__func__,
error);
m_freem(m);
return (error);
}
/*
* Set daddr to the physical mapping page.
*/
bf->bf_daddr = bf->bf_segs[0].ds_addr;
/*
* Prepare for the upcoming read.
*
* We need to both sync some data into the buffer (the zero'ed
* descriptor payload) and also prepare for the read that's going
* to occur.
*/
bus_dmamap_sync(sc->sc_dmat, bf->bf_dmamap,
BUS_DMASYNC_PREREAD | BUS_DMASYNC_PREWRITE);
/* Finish! */
return (0);
}
/*
* Allocate a RX buffer.
*/
static struct ath_buf *
ath_edma_rxbuf_alloc(struct ath_softc *sc)
{
struct ath_buf *bf;
int error;
ATH_RX_LOCK_ASSERT(sc);
/* Allocate buffer */
bf = TAILQ_FIRST(&sc->sc_rxbuf);
/* XXX shouldn't happen upon startup? */
if (bf == NULL) {
DPRINTF(sc, ATH_DEBUG_EDMA_RX, "%s: nothing on rxbuf?!\n",
__func__);
return (NULL);
}
/* Remove it from the free list */
TAILQ_REMOVE(&sc->sc_rxbuf, bf, bf_list);
/* Assign RX mbuf to it */
error = ath_edma_rxbuf_init(sc, bf);
if (error != 0) {
device_printf(sc->sc_dev,
"%s: bf=%p, rxbuf alloc failed! error=%d\n",
__func__,
bf,
error);
TAILQ_INSERT_TAIL(&sc->sc_rxbuf, bf, bf_list);
return (NULL);
}
return (bf);
}
static void
ath_edma_rxbuf_free(struct ath_softc *sc, struct ath_buf *bf)
{
ATH_RX_LOCK_ASSERT(sc);
/*
* Only unload the frame if we haven't consumed
* the mbuf via ath_rx_pkt().
*/
if (bf->bf_m) {
bus_dmamap_unload(sc->sc_dmat, bf->bf_dmamap);
m_freem(bf->bf_m);
bf->bf_m = NULL;
}
/* XXX lock? */
TAILQ_INSERT_TAIL(&sc->sc_rxbuf, bf, bf_list);
}
/*
* Allocate up to 'n' entries and push them onto the hardware FIFO.
*
* Return how many entries were successfully pushed onto the
* FIFO.
*/
static int
ath_edma_rxfifo_alloc(struct ath_softc *sc, HAL_RX_QUEUE qtype, int nbufs)
{
struct ath_rx_edma *re = &sc->sc_rxedma[qtype];
struct ath_buf *bf;
int i;
ATH_RX_LOCK_ASSERT(sc);
/*
* Allocate buffers until the FIFO is full or nbufs is reached.
*/
for (i = 0; i < nbufs && re->m_fifo_depth < re->m_fifolen; i++) {
/* Ensure the FIFO is already blank, complain loudly! */
if (re->m_fifo[re->m_fifo_tail] != NULL) {
device_printf(sc->sc_dev,
"%s: Q%d: fifo[%d] != NULL (%p)\n",
__func__,
qtype,
re->m_fifo_tail,
re->m_fifo[re->m_fifo_tail]);
/* Free the slot */
ath_edma_rxbuf_free(sc, re->m_fifo[re->m_fifo_tail]);
re->m_fifo_depth--;
/* XXX check it's not < 0 */
re->m_fifo[re->m_fifo_tail] = NULL;
}
bf = ath_edma_rxbuf_alloc(sc);
/* XXX should ensure the FIFO is not NULL? */
if (bf == NULL) {
DPRINTF(sc, ATH_DEBUG_EDMA_RX,
"%s: Q%d: alloc failed: i=%d, nbufs=%d?\n",
__func__,
qtype,
i,
nbufs);
break;
}
re->m_fifo[re->m_fifo_tail] = bf;
/* Write to the RX FIFO */
DPRINTF(sc, ATH_DEBUG_EDMA_RX,
"%s: Q%d: putrxbuf=%p (0x%jx)\n",
__func__,
qtype,
bf->bf_desc,
(uintmax_t) bf->bf_daddr);
ath_hal_putrxbuf(sc->sc_ah, bf->bf_daddr, qtype);
re->m_fifo_depth++;
INCR(re->m_fifo_tail, re->m_fifolen);
}
/*
* Return how many were allocated.
*/
DPRINTF(sc, ATH_DEBUG_EDMA_RX, "%s: Q%d: nbufs=%d, nalloced=%d\n",
__func__,
qtype,
nbufs,
i);
return (i);
}
static int
ath_edma_rxfifo_flush(struct ath_softc *sc, HAL_RX_QUEUE qtype)
{
struct ath_rx_edma *re = &sc->sc_rxedma[qtype];
int i;
ATH_RX_LOCK_ASSERT(sc);
for (i = 0; i < re->m_fifolen; i++) {
if (re->m_fifo[i] != NULL) {
#ifdef ATH_DEBUG
struct ath_buf *bf = re->m_fifo[i];
if (sc->sc_debug & ATH_DEBUG_RECV_DESC)
ath_printrxbuf(sc, bf, 0, HAL_OK);
#endif
ath_edma_rxbuf_free(sc, re->m_fifo[i]);
re->m_fifo[i] = NULL;
re->m_fifo_depth--;
}
}
if (re->m_rxpending != NULL) {
m_freem(re->m_rxpending);
re->m_rxpending = NULL;
}
re->m_fifo_head = re->m_fifo_tail = re->m_fifo_depth = 0;
return (0);
}
/*
* Setup the initial RX FIFO structure.
*/
static int
ath_edma_setup_rxfifo(struct ath_softc *sc, HAL_RX_QUEUE qtype)
{
struct ath_rx_edma *re = &sc->sc_rxedma[qtype];
ATH_RX_LOCK_ASSERT(sc);
if (! ath_hal_getrxfifodepth(sc->sc_ah, qtype, &re->m_fifolen)) {
device_printf(sc->sc_dev, "%s: qtype=%d, failed\n",
__func__,
qtype);
return (-EINVAL);
}
if (bootverbose)
device_printf(sc->sc_dev,
"%s: type=%d, FIFO depth = %d entries\n",
__func__,
qtype,
re->m_fifolen);
/* Allocate ath_buf FIFO array, pre-zero'ed */
re->m_fifo = malloc(sizeof(struct ath_buf *) * re->m_fifolen,
M_ATHDEV,
M_NOWAIT | M_ZERO);
if (re->m_fifo == NULL) {
device_printf(sc->sc_dev, "%s: malloc failed\n",
__func__);
return (-ENOMEM);
}
/*
* Set initial "empty" state.
*/
re->m_rxpending = NULL;
re->m_fifo_head = re->m_fifo_tail = re->m_fifo_depth = 0;
return (0);
}
static int
ath_edma_rxfifo_free(struct ath_softc *sc, HAL_RX_QUEUE qtype)
{
struct ath_rx_edma *re = &sc->sc_rxedma[qtype];
device_printf(sc->sc_dev, "%s: called; qtype=%d\n",
__func__,
qtype);
free(re->m_fifo, M_ATHDEV);
return (0);
}
static int
ath_edma_dma_rxsetup(struct ath_softc *sc)
{
int error;
/*
* Create RX DMA tag and buffers.
*/
error = ath_descdma_setup_rx_edma(sc, &sc->sc_rxdma, &sc->sc_rxbuf,
"rx", ath_rxbuf, sc->sc_rx_statuslen);
if (error != 0)
return error;
ATH_RX_LOCK(sc);
(void) ath_edma_setup_rxfifo(sc, HAL_RX_QUEUE_HP);
(void) ath_edma_setup_rxfifo(sc, HAL_RX_QUEUE_LP);
ATH_RX_UNLOCK(sc);
return (0);
}
static int
ath_edma_dma_rxteardown(struct ath_softc *sc)
{
ATH_RX_LOCK(sc);
ath_edma_flush_deferred_queue(sc);
ath_edma_rxfifo_flush(sc, HAL_RX_QUEUE_HP);
ath_edma_rxfifo_free(sc, HAL_RX_QUEUE_HP);
ath_edma_rxfifo_flush(sc, HAL_RX_QUEUE_LP);
ath_edma_rxfifo_free(sc, HAL_RX_QUEUE_LP);
ATH_RX_UNLOCK(sc);
/* Free RX ath_buf */
/* Free RX DMA tag */
if (sc->sc_rxdma.dd_desc_len != 0)
ath_descdma_cleanup(sc, &sc->sc_rxdma, &sc->sc_rxbuf);
return (0);
}
void
ath_recv_setup_edma(struct ath_softc *sc)
{
/* Set buffer size to 4k */
sc->sc_edma_bufsize = 4096;
/* Fetch EDMA field and buffer sizes */
(void) ath_hal_getrxstatuslen(sc->sc_ah, &sc->sc_rx_statuslen);
/* Configure the hardware with the RX buffer size */
(void) ath_hal_setrxbufsize(sc->sc_ah, sc->sc_edma_bufsize -
sc->sc_rx_statuslen);
if (bootverbose) {
device_printf(sc->sc_dev, "RX status length: %d\n",
sc->sc_rx_statuslen);
device_printf(sc->sc_dev, "RX buffer size: %d\n",
sc->sc_edma_bufsize);
}
sc->sc_rx.recv_stop = ath_edma_stoprecv;
sc->sc_rx.recv_start = ath_edma_startrecv;
sc->sc_rx.recv_flush = ath_edma_recv_flush;
sc->sc_rx.recv_tasklet = ath_edma_recv_tasklet;
sc->sc_rx.recv_rxbuf_init = ath_edma_rxbuf_init;
sc->sc_rx.recv_setup = ath_edma_dma_rxsetup;
sc->sc_rx.recv_teardown = ath_edma_dma_rxteardown;
sc->sc_rx.recv_sched = ath_edma_recv_sched;
sc->sc_rx.recv_sched_queue = ath_edma_recv_sched_queue;
}