freebsd-skq/sys/dev/mii/ciphy.c
marius 278d761d73 o Flesh out the generic IEEE 802.3 annex 31B full duplex flow control
support in mii(4):
  - Merge generic flow control advertisement (which can be enabled by
    passing by MIIF_DOPAUSE to mii_attach(9)) and parsing support from
    NetBSD into mii_physubr.c and ukphy_subr.c. Unlike as in NetBSD,
    IFM_FLOW isn't implemented as a global option via the "don't care
    mask" but instead as a media specific option this. This has the
    following advantages:
    o allows flow control advertisement with autonegotiation to be
      turned on and off via ifconfig(8) with the default typically
      being off (though MIIF_FORCEPAUSE has been added causing flow
      control to be always advertised, allowing to easily MFC this
      changes for drivers that previously used home-grown support for
      flow control that behaved that way without breaking POLA)
    o allows to deal with PHY drivers where flow control advertisement
      with manual selection doesn't work or at least isn't implemented,
      like it's the case with brgphy(4), e1000phy(4) and ip1000phy(4),
      by setting MIIF_NOMANPAUSE
    o the available combinations of media options are readily available
      from the `ifconfig -m` output
  - Add IFM_FLOW to IFM_SHARED_OPTION_DESCRIPTIONS and IFM_ETH_RXPAUSE
    and IFM_ETH_TXPAUSE to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so
    these are understood by ifconfig(8).
o Make the master/slave support in mii(4) actually usable:
  - Change IFM_ETH_MASTER from being implemented as a global option via
    the "don't care mask" to a media specific one as it actually is only
    applicable to IFM_1000_T to date.
  - Let mii_phy_setmedia() set GTCR_MAN_MS in IFM_1000_T slave mode to
    actually configure manually selected slave mode (like we also do in
    the PHY specific implementations).
  - Add IFM_ETH_MASTER to IFM_SUBTYPE_ETHERNET_OPTION_DESCRIPTIONS so it
    is understood by ifconfig(8).
o Switch bge(4), bce(4), msk(4), nfe(4) and stge(4) along with brgphy(4),
  e1000phy(4) and ip1000phy(4) to use the generic flow control support
  instead of home-grown solutions via IFM_FLAGs. This includes changing
  these PHY drivers and smcphy(4) to no longer unconditionally advertise
  support for flow control but only if the selected media has IFM_FLOW
  set (or MIIF_FORCEPAUSE is set) and implemented for these media variants,
  i.e. typically only for copper.
o Switch brgphy(4), ciphy(4), e1000phy(4) and ip1000phy(4) to report and
  set IFM_1000_T master mode via IFM_ETH_MASTER instead of via IFF_LINK0
  and some IFM_FLAGn.
o Switch brgphy(4) to add at least the the supported copper media based on
  the contents of the BMSR via mii_phy_add_media() instead of hardcoding
  them. The latter approach seems to have developed historically, besides
  causing unnecessary code duplication it was also undesirable because
  brgphy_mii_phy_auto() already based the capability advertisement on the
  contents of the BMSR though.
o Let brgphy(4) set IFM_1000_T master mode on all supported PHY and not
  just BCM5701. Apparently this was a misinterpretation of a workaround
  in the Linux tg3 driver; BCM5701 seem to require RGPHY_1000CTL_MSE and
  BRGPHY_1000CTL_MSC to be set when configuring autonegotiation but
  this doesn't mean we can't set these as well on other PHYs for manual
  media selection.
o Let ukphy_status() report IFM_1000_T master mode via IFM_ETH_MASTER so
  IFM_1000_T master mode support now is generally available with all PHY
  drivers.
o Don't let e1000phy(4) set master/slave bits for IFM_1000_SX as it's
  not applicable there.

Reviewed by:	yongari (plus additional testing)
Obtained from:	NetBSD (partially), OpenBSD (partially)
MFC after:	2 weeks
2010-11-14 13:26:10 +00:00

402 lines
10 KiB
C

/*-
* Copyright (c) 2004
* Bill Paul <wpaul@windriver.com>. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. All advertising materials mentioning features or use of this software
* must display the following acknowledgement:
* This product includes software developed by Bill Paul.
* 4. Neither the name of the author nor the names of any co-contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD
* BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
* THE POSSIBILITY OF SUCH DAMAGE.
*/
#include <sys/cdefs.h>
__FBSDID("$FreeBSD$");
/*
* Driver for the Cicada/Vitesse CS/VSC8xxx 10/100/1000 copper PHY.
*/
#include <sys/param.h>
#include <sys/systm.h>
#include <sys/kernel.h>
#include <sys/module.h>
#include <sys/socket.h>
#include <sys/bus.h>
#include <net/if.h>
#include <net/if_arp.h>
#include <net/if_media.h>
#include <dev/mii/mii.h>
#include <dev/mii/miivar.h>
#include "miidevs.h"
#include <dev/mii/ciphyreg.h>
#include "miibus_if.h"
#include <machine/bus.h>
static int ciphy_probe(device_t);
static int ciphy_attach(device_t);
static device_method_t ciphy_methods[] = {
/* device interface */
DEVMETHOD(device_probe, ciphy_probe),
DEVMETHOD(device_attach, ciphy_attach),
DEVMETHOD(device_detach, mii_phy_detach),
DEVMETHOD(device_shutdown, bus_generic_shutdown),
{ 0, 0 }
};
static devclass_t ciphy_devclass;
static driver_t ciphy_driver = {
"ciphy",
ciphy_methods,
sizeof(struct mii_softc)
};
DRIVER_MODULE(ciphy, miibus, ciphy_driver, ciphy_devclass, 0, 0);
static int ciphy_service(struct mii_softc *, struct mii_data *, int);
static void ciphy_status(struct mii_softc *);
static void ciphy_reset(struct mii_softc *);
static void ciphy_fixup(struct mii_softc *);
static const struct mii_phydesc ciphys[] = {
MII_PHY_DESC(CICADA, CS8201),
MII_PHY_DESC(CICADA, CS8201A),
MII_PHY_DESC(CICADA, CS8201B),
MII_PHY_DESC(CICADA, CS8204),
MII_PHY_DESC(CICADA, VSC8211),
MII_PHY_DESC(CICADA, CS8244),
MII_PHY_DESC(VITESSE, VSC8601),
MII_PHY_END
};
static int
ciphy_probe(device_t dev)
{
return (mii_phy_dev_probe(dev, ciphys, BUS_PROBE_DEFAULT));
}
static int
ciphy_attach(device_t dev)
{
struct mii_softc *sc;
struct mii_attach_args *ma;
struct mii_data *mii;
sc = device_get_softc(dev);
ma = device_get_ivars(dev);
sc->mii_dev = device_get_parent(dev);
mii = ma->mii_data;
LIST_INSERT_HEAD(&mii->mii_phys, sc, mii_list);
sc->mii_flags = miibus_get_flags(dev);
sc->mii_inst = mii->mii_instance++;
sc->mii_phy = ma->mii_phyno;
sc->mii_service = ciphy_service;
sc->mii_pdata = mii;
sc->mii_flags |= MIIF_NOISOLATE;
ciphy_reset(sc);
sc->mii_capabilities = PHY_READ(sc, MII_BMSR) & ma->mii_capmask;
if (sc->mii_capabilities & BMSR_EXTSTAT)
sc->mii_extcapabilities = PHY_READ(sc, MII_EXTSR);
device_printf(dev, " ");
mii_phy_add_media(sc);
printf("\n");
MIIBUS_MEDIAINIT(sc->mii_dev);
return (0);
}
static int
ciphy_service(struct mii_softc *sc, struct mii_data *mii, int cmd)
{
struct ifmedia_entry *ife = mii->mii_media.ifm_cur;
int reg, speed, gig;
switch (cmd) {
case MII_POLLSTAT:
break;
case MII_MEDIACHG:
/*
* If the interface is not up, don't do anything.
*/
if ((mii->mii_ifp->if_flags & IFF_UP) == 0)
break;
ciphy_fixup(sc); /* XXX hardware bug work-around */
switch (IFM_SUBTYPE(ife->ifm_media)) {
case IFM_AUTO:
#ifdef foo
/*
* If we're already in auto mode, just return.
*/
if (PHY_READ(sc, CIPHY_MII_BMCR) & CIPHY_BMCR_AUTOEN)
return (0);
#endif
(void)mii_phy_auto(sc);
break;
case IFM_1000_T:
speed = CIPHY_S1000;
goto setit;
case IFM_100_TX:
speed = CIPHY_S100;
goto setit;
case IFM_10_T:
speed = CIPHY_S10;
setit:
if ((ife->ifm_media & IFM_GMASK) == IFM_FDX) {
speed |= CIPHY_BMCR_FDX;
gig = CIPHY_1000CTL_AFD;
} else {
gig = CIPHY_1000CTL_AHD;
}
PHY_WRITE(sc, CIPHY_MII_1000CTL, 0);
PHY_WRITE(sc, CIPHY_MII_BMCR, speed);
PHY_WRITE(sc, CIPHY_MII_ANAR, CIPHY_SEL_TYPE);
if (IFM_SUBTYPE(ife->ifm_media) != IFM_1000_T)
break;
gig |= CIPHY_1000CTL_MSE;
if ((ife->ifm_media & IFM_ETH_MASTER) != 0)
gig |= CIPHY_1000CTL_MSC;
PHY_WRITE(sc, CIPHY_MII_1000CTL, gig);
PHY_WRITE(sc, CIPHY_MII_BMCR,
speed | CIPHY_BMCR_AUTOEN | CIPHY_BMCR_STARTNEG);
break;
case IFM_NONE:
PHY_WRITE(sc, MII_BMCR, BMCR_ISO | BMCR_PDOWN);
break;
default:
return (EINVAL);
}
break;
case MII_TICK:
/*
* Is the interface even up?
*/
if ((mii->mii_ifp->if_flags & IFF_UP) == 0)
return (0);
/*
* Only used for autonegotiation.
*/
if (IFM_SUBTYPE(ife->ifm_media) != IFM_AUTO)
break;
/*
* Check to see if we have link. If we do, we don't
* need to restart the autonegotiation process. Read
* the BMSR twice in case it's latched.
*/
reg = PHY_READ(sc, MII_BMSR) | PHY_READ(sc, MII_BMSR);
if (reg & BMSR_LINK)
break;
/* Announce link loss right after it happens. */
if (++sc->mii_ticks == 0)
break;
/*
* Only retry autonegotiation every mii_anegticks seconds.
*/
if (sc->mii_ticks <= sc->mii_anegticks)
break;
sc->mii_ticks = 0;
mii_phy_auto(sc);
break;
}
/* Update the media status. */
ciphy_status(sc);
/*
* Callback if something changed. Note that we need to poke
* apply fixups for certain PHY revs.
*/
if (sc->mii_media_active != mii->mii_media_active ||
sc->mii_media_status != mii->mii_media_status ||
cmd == MII_MEDIACHG) {
ciphy_fixup(sc);
}
mii_phy_update(sc, cmd);
return (0);
}
static void
ciphy_status(struct mii_softc *sc)
{
struct mii_data *mii = sc->mii_pdata;
int bmsr, bmcr;
mii->mii_media_status = IFM_AVALID;
mii->mii_media_active = IFM_ETHER;
bmsr = PHY_READ(sc, MII_BMSR) | PHY_READ(sc, MII_BMSR);
if (bmsr & BMSR_LINK)
mii->mii_media_status |= IFM_ACTIVE;
bmcr = PHY_READ(sc, CIPHY_MII_BMCR);
if (bmcr & CIPHY_BMCR_LOOP)
mii->mii_media_active |= IFM_LOOP;
if (bmcr & CIPHY_BMCR_AUTOEN) {
if ((bmsr & CIPHY_BMSR_ACOMP) == 0) {
/* Erg, still trying, I guess... */
mii->mii_media_active |= IFM_NONE;
return;
}
}
bmsr = PHY_READ(sc, CIPHY_MII_AUXCSR);
switch (bmsr & CIPHY_AUXCSR_SPEED) {
case CIPHY_SPEED10:
mii->mii_media_active |= IFM_10_T;
break;
case CIPHY_SPEED100:
mii->mii_media_active |= IFM_100_TX;
break;
case CIPHY_SPEED1000:
mii->mii_media_active |= IFM_1000_T;
break;
default:
device_printf(sc->mii_dev, "unknown PHY speed %x\n",
bmsr & CIPHY_AUXCSR_SPEED);
break;
}
if (bmsr & CIPHY_AUXCSR_FDX)
mii->mii_media_active |= IFM_FDX;
else
mii->mii_media_active |= IFM_HDX;
if ((IFM_SUBTYPE(mii->mii_media_active) == IFM_1000_T) &&
(PHY_READ(sc, CIPHY_MII_1000STS) & CIPHY_1000STS_MSR) != 0)
mii->mii_media_active |= IFM_ETH_MASTER;
}
static void
ciphy_reset(struct mii_softc *sc)
{
mii_phy_reset(sc);
DELAY(1000);
}
#define PHY_SETBIT(x, y, z) \
PHY_WRITE(x, y, (PHY_READ(x, y) | (z)))
#define PHY_CLRBIT(x, y, z) \
PHY_WRITE(x, y, (PHY_READ(x, y) & ~(z)))
static void
ciphy_fixup(struct mii_softc *sc)
{
uint16_t model;
uint16_t status, speed;
uint16_t val;
model = MII_MODEL(PHY_READ(sc, CIPHY_MII_PHYIDR2));
status = PHY_READ(sc, CIPHY_MII_AUXCSR);
speed = status & CIPHY_AUXCSR_SPEED;
if (strcmp(device_get_name(device_get_parent(sc->mii_dev)),
"nfe") == 0) {
/* need to set for 2.5V RGMII for NVIDIA adapters */
val = PHY_READ(sc, CIPHY_MII_ECTL1);
val &= ~(CIPHY_ECTL1_IOVOL | CIPHY_ECTL1_INTSEL);
val |= (CIPHY_IOVOL_2500MV | CIPHY_INTSEL_RGMII);
PHY_WRITE(sc, CIPHY_MII_ECTL1, val);
/* From Linux. */
val = PHY_READ(sc, CIPHY_MII_AUXCSR);
val |= CIPHY_AUXCSR_MDPPS;
PHY_WRITE(sc, CIPHY_MII_AUXCSR, val);
val = PHY_READ(sc, CIPHY_MII_10BTCSR);
val |= CIPHY_10BTCSR_ECHO;
PHY_WRITE(sc, CIPHY_MII_10BTCSR, val);
}
switch (model) {
case MII_MODEL_CICADA_CS8204:
case MII_MODEL_CICADA_CS8201:
/* Turn off "aux mode" (whatever that means) */
PHY_SETBIT(sc, CIPHY_MII_AUXCSR, CIPHY_AUXCSR_MDPPS);
/*
* Work around speed polling bug in VT3119/VT3216
* when using MII in full duplex mode.
*/
if ((speed == CIPHY_SPEED10 || speed == CIPHY_SPEED100) &&
(status & CIPHY_AUXCSR_FDX)) {
PHY_SETBIT(sc, CIPHY_MII_10BTCSR, CIPHY_10BTCSR_ECHO);
} else {
PHY_CLRBIT(sc, CIPHY_MII_10BTCSR, CIPHY_10BTCSR_ECHO);
}
/* Enable link/activity LED blink. */
PHY_SETBIT(sc, CIPHY_MII_LED, CIPHY_LED_LINKACTBLINK);
break;
case MII_MODEL_CICADA_CS8201A:
case MII_MODEL_CICADA_CS8201B:
/*
* Work around speed polling bug in VT3119/VT3216
* when using MII in full duplex mode.
*/
if ((speed == CIPHY_SPEED10 || speed == CIPHY_SPEED100) &&
(status & CIPHY_AUXCSR_FDX)) {
PHY_SETBIT(sc, CIPHY_MII_10BTCSR, CIPHY_10BTCSR_ECHO);
} else {
PHY_CLRBIT(sc, CIPHY_MII_10BTCSR, CIPHY_10BTCSR_ECHO);
}
break;
case MII_MODEL_CICADA_VSC8211:
case MII_MODEL_CICADA_CS8244:
case MII_MODEL_VITESSE_VSC8601:
break;
default:
device_printf(sc->mii_dev, "unknown CICADA PHY model %x\n",
model);
break;
}
}