2344 lines
83 KiB
Plaintext
2344 lines
83 KiB
Plaintext
#
|
||
# LINT -- config file for checking all the sources, tries to pull in
|
||
# as much of the source tree as it can.
|
||
#
|
||
# $FreeBSD$
|
||
#
|
||
# NB: You probably don't want to try running a kernel built from this
|
||
# file. Instead, you should start from GENERIC, and add options from
|
||
# this file as required.
|
||
#
|
||
|
||
#
|
||
# This directive is mandatory; it defines the architecture to be
|
||
# configured for; in this case, the 386 family based IBM-PC and
|
||
# compatibles.
|
||
#
|
||
machine i386
|
||
|
||
#
|
||
# This is the ``identification'' of the kernel. Usually this should
|
||
# be the same as the name of your kernel.
|
||
#
|
||
ident LINT
|
||
|
||
#
|
||
# The `maxusers' parameter controls the static sizing of a number of
|
||
# internal system tables by a complicated formula defined in param.c.
|
||
#
|
||
maxusers 10
|
||
|
||
#
|
||
# The `makeoptions' parameter allows variables to be passed to the
|
||
# generated Makefile in the build area.
|
||
#
|
||
# CONF_CFLAGS gives some extra compiler flags that are added to ${CFLAGS}
|
||
# after most other flags. Here we use it to inhibit use of non-optimal
|
||
# gcc builtin functions (e.g., memcmp).
|
||
#
|
||
# DEBUG happens to be magic.
|
||
# The following is equivalent to 'config -g KERNELNAME' and creates
|
||
# 'kernel.debug' compiled with -g debugging as well as a normal
|
||
# 'kernel'. Use 'make install.debug' to install the debug kernel
|
||
# but that isn't normally necessary as the debug symbols are not loaded
|
||
# by the kernel and are not useful there anyway.
|
||
#
|
||
# KERNEL can be overridden so that you can change the default name of your
|
||
# kernel.
|
||
#
|
||
makeoptions CONF_CFLAGS=-fno-builtin #Don't allow use of memcmp, etc.
|
||
#makeoptions DEBUG=-g #Build kernel with gdb(1) debug symbols
|
||
#makeoptions KERNEL=foo #Build kernel "foo" and install "/foo"
|
||
|
||
#
|
||
# Certain applications can grow to be larger than the 128M limit
|
||
# that FreeBSD initially imposes. Below are some options to
|
||
# allow that limit to grow to 256MB, and can be increased further
|
||
# with changing the parameters. MAXDSIZ is the maximum that the
|
||
# limit can be set to, and the DFLDSIZ is the default value for
|
||
# the limit. You might want to set the default lower than the
|
||
# max, and explicitly set the maximum with a shell command for processes
|
||
# that regularly exceed the limit like INND.
|
||
#
|
||
options MAXDSIZ="(256*1024*1024)"
|
||
options DFLDSIZ="(256*1024*1024)"
|
||
|
||
#
|
||
# BLKDEV_IOSIZE sets the default block size used in user block
|
||
# device I/O. Note that this value will be overriden by the label
|
||
# when specifying a block device from a label with a non-0
|
||
# partition blocksize. The default is PAGE_SIZE.
|
||
#
|
||
options BLKDEV_IOSIZE=8192
|
||
|
||
# Options for the VM subsystem
|
||
#options PQ_NOOPT # No coloring
|
||
options PQ_LARGECACHE # color for 512k/16k cache
|
||
#options PQ_HUGECACHE # color for 1024k/16k cache
|
||
#options PQ_MEDIUMCACHE # color for 64k/16k cache
|
||
#options PQ_NORMALCACHE # color for 256k/16k cache
|
||
|
||
# This allows you to actually store this configuration file into
|
||
# the kernel binary itself, where it may be later read by saying:
|
||
# strings -aout -n 3 /kernel | grep ^___ | sed -e 's/^___//' > MYKERNEL
|
||
#
|
||
options INCLUDE_CONFIG_FILE # Include this file in kernel
|
||
|
||
|
||
#####################################################################
|
||
# SMP OPTIONS:
|
||
#
|
||
# SMP enables building of a Symmetric MultiProcessor Kernel.
|
||
# APIC_IO enables the use of the IO APIC for Symmetric I/O.
|
||
# NCPU sets the number of CPUs, defaults to 2.
|
||
# NBUS sets the number of busses, defaults to 4.
|
||
# NAPIC sets the number of IO APICs on the motherboard, defaults to 1.
|
||
# NINTR sets the total number of INTs provided by the motherboard.
|
||
#
|
||
# Notes:
|
||
#
|
||
# An SMP kernel will ONLY run on an Intel MP spec. qualified motherboard.
|
||
#
|
||
# Be sure to disable 'cpu I386_CPU' && 'cpu I486_CPU' for SMP kernels.
|
||
#
|
||
# Check the 'Rogue SMP hardware' section to see if additional options
|
||
# are required by your hardware.
|
||
#
|
||
|
||
# Mandatory:
|
||
options SMP # Symmetric MultiProcessor Kernel
|
||
options APIC_IO # Symmetric (APIC) I/O
|
||
|
||
# Optional, these are the defaults plus 1:
|
||
options NCPU=5 # number of CPUs
|
||
options NBUS=5 # number of busses
|
||
options NAPIC=2 # number of IO APICs
|
||
options NINTR=25 # number of INTs
|
||
|
||
#
|
||
# Rogue SMP hardware:
|
||
#
|
||
|
||
# Bridged PCI cards:
|
||
#
|
||
# The MP tables of most of the current generation MP motherboards
|
||
# do NOT properly support bridged PCI cards. To use one of these
|
||
# cards you should refer to ???
|
||
|
||
|
||
#####################################################################
|
||
# CPU OPTIONS
|
||
|
||
#
|
||
# You must specify at least one CPU (the one you intend to run on);
|
||
# deleting the specification for CPUs you don't need to use may make
|
||
# parts of the system run faster. This is especially true removing
|
||
# I386_CPU.
|
||
#
|
||
cpu I386_CPU
|
||
cpu I486_CPU
|
||
cpu I586_CPU # aka Pentium(tm)
|
||
cpu I686_CPU # aka Pentium Pro(tm)
|
||
|
||
#
|
||
# Options for CPU features.
|
||
#
|
||
# CPU_BLUELIGHTNING_FPU_OP_CACHE enables FPU operand cache on IBM
|
||
# BlueLightning CPU. It works only with Cyrix FPU, and this option
|
||
# should not be used with Intel FPU.
|
||
#
|
||
# CPU_BLUELIGHTNING_3X enables triple-clock mode on IBM Blue Lightning
|
||
# CPU if CPU supports it. The default is double-clock mode on
|
||
# BlueLightning CPU box.
|
||
#
|
||
# CPU_BTB_EN enables branch target buffer on Cyrix 5x86 (NOTE 1).
|
||
#
|
||
# CPU_DIRECT_MAPPED_CACHE sets L1 cache of Cyrix 486DLC CPU in direct
|
||
# mapped mode. Default is 2-way set associative mode.
|
||
#
|
||
# CPU_CYRIX_NO_LOCK enables weak locking for the entire address space
|
||
# of Cyrix 6x86 and 6x86MX CPUs by setting the NO_LOCK bit of CCR1.
|
||
# Otherwise, the NO_LOCK bit of CCR1 is cleared. (NOTE 3)
|
||
#
|
||
# CPU_DISABLE_5X86_LSSER disables load store serialize (i.e. enables
|
||
# reorder). This option should not be used if you use memory mapped
|
||
# I/O device(s).
|
||
#
|
||
# CPU_FASTER_5X86_FPU enables faster FPU exception handler.
|
||
#
|
||
# CPU_I486_ON_386 enables CPU cache on i486 based CPU upgrade products
|
||
# for i386 machines.
|
||
#
|
||
# CPU_IORT defines I/O clock delay time (NOTE 1). Default values of
|
||
# I/O clock delay time on Cyrix 5x86 and 6x86 are 0 and 7,respectively
|
||
# (no clock delay).
|
||
#
|
||
# CPU_LOOP_EN prevents flushing the prefetch buffer if the destination
|
||
# of a jump is already present in the prefetch buffer on Cyrix 5x86(NOTE
|
||
# 1).
|
||
#
|
||
# CPU_RSTK_EN enables return stack on Cyrix 5x86 (NOTE 1).
|
||
#
|
||
# CPU_SUSP_HLT enables suspend on HALT. If this option is set, CPU
|
||
# enters suspend mode following execution of HALT instruction.
|
||
#
|
||
# CPU_WT_ALLOC enables write allocation on Cyrix 6x86/6x86MX and AMD
|
||
# K5/K6/K6-2 cpus.
|
||
#
|
||
# CYRIX_CACHE_WORKS enables CPU cache on Cyrix 486 CPUs with cache
|
||
# flush at hold state.
|
||
#
|
||
# CYRIX_CACHE_REALLY_WORKS enables (1) CPU cache on Cyrix 486 CPUs
|
||
# without cache flush at hold state, and (2) write-back CPU cache on
|
||
# Cyrix 6x86 whose revision < 2.7 (NOTE 2).
|
||
#
|
||
# NO_F00F_HACK disables the hack that prevents Pentiums (and ONLY
|
||
# Pentiums) from locking up when a LOCK CMPXCHG8B instruction is
|
||
# executed. This should be included for ALL kernels that won't run
|
||
# on a Pentium.
|
||
#
|
||
# NO_MEMORY_HOLE is an optimisation for systems with AMD K6 processors
|
||
# which indicates that the 15-16MB range is *definitely* not being
|
||
# occupied by an ISA memory hole.
|
||
#
|
||
# NOTE 1: The options, CPU_BTB_EN, CPU_LOOP_EN, CPU_IORT,
|
||
# CPU_LOOP_EN and CPU_RSTK_EN should not be used because of CPU bugs.
|
||
# These options may crash your system.
|
||
#
|
||
# NOTE 2: If CYRIX_CACHE_REALLY_WORKS is not set, CPU cache is enabled
|
||
# in write-through mode when revision < 2.7. If revision of Cyrix
|
||
# 6x86 >= 2.7, CPU cache is always enabled in write-back mode.
|
||
#
|
||
# NOTE 3: This option may cause failures for software that requires
|
||
# locked cycles in order to operate correctly.
|
||
#
|
||
options CPU_BLUELIGHTNING_FPU_OP_CACHE
|
||
options CPU_BLUELIGHTNING_3X
|
||
options CPU_BTB_EN
|
||
options CPU_DIRECT_MAPPED_CACHE
|
||
options CPU_DISABLE_5X86_LSSER
|
||
options CPU_FASTER_5X86_FPU
|
||
options CPU_I486_ON_386
|
||
options CPU_IORT
|
||
options CPU_LOOP_EN
|
||
options CPU_RSTK_EN
|
||
options CPU_SUSP_HLT
|
||
options CPU_WT_ALLOC
|
||
options CYRIX_CACHE_WORKS
|
||
options CYRIX_CACHE_REALLY_WORKS
|
||
#options NO_F00F_HACK
|
||
|
||
#
|
||
# A math emulator is mandatory if you wish to run on hardware which
|
||
# does not have a floating-point processor. Pick either the original,
|
||
# bogus (but freely-distributable) math emulator, or a much more
|
||
# fully-featured but GPL-licensed emulator taken from Linux.
|
||
#
|
||
options MATH_EMULATE #Support for x87 emulation
|
||
# Don't enable both of these in a real config.
|
||
options GPL_MATH_EMULATE #Support for x87 emulation via
|
||
#new math emulator
|
||
|
||
|
||
#####################################################################
|
||
# COMPATIBILITY OPTIONS
|
||
|
||
#
|
||
# Implement system calls compatible with 4.3BSD and older versions of
|
||
# FreeBSD. You probably do NOT want to remove this as much current code
|
||
# still relies on the 4.3 emulation.
|
||
#
|
||
options COMPAT_43
|
||
|
||
#
|
||
# Allow user-mode programs to manipulate their local descriptor tables.
|
||
# This option is required for the WINE Windows(tm) emulator, and is
|
||
# not used by anything else (that we know of).
|
||
#
|
||
options USER_LDT #allow user-level control of i386 ldt
|
||
|
||
#
|
||
# These three options provide support for System V Interface
|
||
# Definition-style interprocess communication, in the form of shared
|
||
# memory, semaphores, and message queues, respectively.
|
||
#
|
||
options SYSVSHM
|
||
options SYSVSEM
|
||
options SYSVMSG
|
||
|
||
|
||
#####################################################################
|
||
# DEBUGGING OPTIONS
|
||
|
||
#
|
||
# Enable the kernel debugger.
|
||
#
|
||
options DDB
|
||
|
||
#
|
||
# Don't drop into DDB for a panic. Intended for unattended operation
|
||
# where you may want to drop to DDB from the console, but still want
|
||
# the machine to recover from a panic
|
||
#
|
||
options DDB_UNATTENDED
|
||
|
||
#
|
||
# If using GDB remote mode to debug the kernel, there's a non-standard
|
||
# extension to the remote protocol that can be used to use the serial
|
||
# port as both the debugging port and the system console. It's non-
|
||
# standard and you're on your own if you enable it. See also the
|
||
# "remotechat" variables in the FreeBSD specific version of gdb.
|
||
#
|
||
options GDB_REMOTE_CHAT
|
||
|
||
#
|
||
# KTRACE enables the system-call tracing facility ktrace(2).
|
||
#
|
||
options KTRACE #kernel tracing
|
||
|
||
#
|
||
# The INVARIANTS option is used in a number of source files to enable
|
||
# extra sanity checking of internal structures. This support is not
|
||
# enabled by default because of the extra time it would take to check
|
||
# for these conditions, which can only occur as a result of
|
||
# programming errors.
|
||
#
|
||
options INVARIANTS
|
||
|
||
#
|
||
# The INVARIANT_SUPPORT option makes us compile in support for
|
||
# verifying some of the internal structures. It is a prerequisite for
|
||
# 'INVARIANTS', as enabling 'INVARIANTS' will make these functions be
|
||
# called. The intent is that you can set 'INVARIANTS' for single
|
||
# source files (by changing the source file or specifying it on the
|
||
# command line) if you have 'INVARIANT_SUPPORT' enabled.
|
||
#
|
||
options INVARIANT_SUPPORT
|
||
|
||
#
|
||
# The DIAGNOSTIC option is used to enable extra debugging information
|
||
# from some parts of the kernel. As this makes everything more noisy,
|
||
# it is disabled by default.
|
||
#
|
||
options DIAGNOSTIC
|
||
|
||
#
|
||
# PERFMON causes the driver for Pentium/Pentium Pro performance counters
|
||
# to be compiled. See perfmon(4) for more information.
|
||
#
|
||
options PERFMON
|
||
|
||
|
||
#
|
||
# This option let some drivers co-exist that can't co-exist in a running
|
||
# system. This is used to be able to compile all kernel code in one go for
|
||
# quality assurance purposes (like this file, which the option takes it name
|
||
# from.)
|
||
#
|
||
options COMPILING_LINT
|
||
|
||
|
||
# XXX - this doesn't belong here.
|
||
# Allow ordinary users to take the console - this is useful for X.
|
||
options UCONSOLE
|
||
|
||
# XXX - this doesn't belong here either
|
||
options USERCONFIG #boot -c editor
|
||
options INTRO_USERCONFIG #imply -c and show intro screen
|
||
options VISUAL_USERCONFIG #visual boot -c editor
|
||
|
||
# XXX - neither does this
|
||
options ROOTDEVNAME=\"da0s2e\"
|
||
|
||
#####################################################################
|
||
# NETWORKING OPTIONS
|
||
|
||
#
|
||
# Protocol families:
|
||
# Only the INET (Internet) family is officially supported in FreeBSD.
|
||
# Source code for the NS (Xerox Network Service) is provided for amusement
|
||
# value.
|
||
#
|
||
options INET #Internet communications protocols
|
||
options INET6 #IPv6 communications protocols
|
||
options IPSEC #IP security
|
||
options IPSEC_ESP #IP security (crypto; define w/ IPSEC)
|
||
options IPSEC_IPV6FWD #IP security tunnel for IPv6
|
||
options IPSEC_DEBUG #debug for IP security
|
||
|
||
options IPX #IPX/SPX communications protocols
|
||
options IPXIP #IPX in IP encapsulation (not available)
|
||
options IPTUNNEL #IP in IPX encapsulation (not available)
|
||
|
||
options NCP #NetWare Core protocol
|
||
|
||
options NETATALK #Appletalk communications protocols
|
||
|
||
# These are currently broken but are shipped due to interest.
|
||
#options NS #Xerox NS protocols
|
||
#options NSIP #XNS over IP
|
||
|
||
# netgraph(4). Enable the base netgraph code with the NETGRAPH option.
|
||
# Individual node types can be enabled with the corresponding option
|
||
# listed below; however, this is not strictly necessary as netgraph
|
||
# will automatically load the corresponding KLD module if the node type
|
||
# is not already compiled into the kernel. Each type below has a
|
||
# corresponding man page, e.g., ng_async(8).
|
||
options NETGRAPH #netgraph(4) system
|
||
options NETGRAPH_ASYNC
|
||
options NETGRAPH_BPF
|
||
options NETGRAPH_CISCO
|
||
options NETGRAPH_ECHO
|
||
options NETGRAPH_FRAME_RELAY
|
||
options NETGRAPH_HOLE
|
||
options NETGRAPH_IFACE
|
||
options NETGRAPH_KSOCKET
|
||
options NETGRAPH_LMI
|
||
options NETGRAPH_PPP
|
||
options NETGRAPH_PPPOE
|
||
options NETGRAPH_PPTPGRE
|
||
options NETGRAPH_RFC1490
|
||
options NETGRAPH_SOCKET
|
||
options NETGRAPH_TEE
|
||
options NETGRAPH_TTY
|
||
options NETGRAPH_UI
|
||
options NETGRAPH_VJC
|
||
|
||
device mn # Munich32x/Falc54 Nx64kbit/sec cards.
|
||
|
||
#
|
||
# Network interfaces:
|
||
# The `loop' pseudo-device is MANDATORY when networking is enabled.
|
||
# The `ether' pseudo-device provides generic code to handle
|
||
# Ethernets; it is MANDATORY when a Ethernet device driver is
|
||
# configured or token-ring is enabled.
|
||
# The 'fddi' pseudo-device provides generic code to support FDDI.
|
||
# The `sppp' pseudo-device serves a similar role for certain types
|
||
# of synchronous PPP links (like `cx', `ar').
|
||
# The `sl' pseudo-device implements the Serial Line IP (SLIP) service.
|
||
# The `ppp' pseudo-device implements the Point-to-Point Protocol.
|
||
# The `bpf' pseudo-device enables the Berkeley Packet Filter. Be
|
||
# aware of the legal and administrative consequences of enabling this
|
||
# option. The number of devices determines the maximum number of
|
||
# simultaneous BPF clients programs runnable.
|
||
# The `disc' pseudo-device implements a minimal network interface,
|
||
# which throws away all packets sent and never receives any. It is
|
||
# included for testing purposes. This shows up as the 'ds' interface.
|
||
# The `tun' pseudo-device implements (user-)ppp and nos-tun
|
||
# The `gif' pseudo-device implements IPv6 over IP4 tunneling,
|
||
# IPv4 over IPv6 tunneling, IPv4 over IPv4 tunneling and
|
||
# IPv6 over IPv6 tunneling.
|
||
# The `faith' pseudo-device captures packets sent to it and diverts them
|
||
# to the IPv4/IPv6 translation daemon.
|
||
# The `ef' pseudo-device provides support for multiple ethernet frame types
|
||
# specified via ETHER_* options. See ef(4) for details.
|
||
#
|
||
# The PPP_BSDCOMP option enables support for compress(1) style entire
|
||
# packet compression, the PPP_DEFLATE is for zlib/gzip style compression.
|
||
# PPP_FILTER enables code for filtering the ppp data stream and selecting
|
||
# events for resetting the demand dial activity timer - requires bpf.
|
||
# See pppd(8) for more details.
|
||
#
|
||
pseudo-device ether #Generic Ethernet
|
||
pseudo-device token #Generic TokenRing
|
||
pseudo-device fddi #Generic FDDI
|
||
pseudo-device sppp #Generic Synchronous PPP
|
||
pseudo-device loop #Network loopback device
|
||
pseudo-device bpf #Berkeley packet filter
|
||
pseudo-device disc #Discard device (ds0, ds1, etc)
|
||
pseudo-device tun #Tunnel driver (ppp(8), nos-tun(8))
|
||
pseudo-device sl 2 #Serial Line IP
|
||
pseudo-device ppp 2 #Point-to-point protocol
|
||
options PPP_BSDCOMP #PPP BSD-compress support
|
||
options PPP_DEFLATE #PPP zlib/deflate/gzip support
|
||
options PPP_FILTER #enable bpf filtering (needs bpf)
|
||
|
||
pseudo-device ef # Multiple ethernet frames support
|
||
options ETHER_II # enable Ethernet_II frame
|
||
options ETHER_8023 # enable Ethernet_802.3 (Novell) frame
|
||
options ETHER_8022 # enable Ethernet_802.2 frame
|
||
options ETHER_SNAP # enable Ethernet_802.2/SNAP frame
|
||
|
||
# for IPv6
|
||
pseudo-device gif 4 #IPv6 and IPv4 tunneling
|
||
pseudo-device faith 1 #for IPv6 and IPv4 translation
|
||
|
||
#
|
||
# Internet family options:
|
||
#
|
||
# TCP_COMPAT_42 causes the TCP code to emulate certain bugs present in
|
||
# 4.2BSD. This option should not be used unless you have a 4.2BSD
|
||
# machine and TCP connections fail.
|
||
#
|
||
# MROUTING enables the kernel multicast packet forwarder, which works
|
||
# with mrouted(8).
|
||
#
|
||
# IPFIREWALL enables support for IP firewall construction, in
|
||
# conjunction with the `ipfw' program. IPFIREWALL_VERBOSE sends
|
||
# logged packets to the system logger. IPFIREWALL_VERBOSE_LIMIT
|
||
# limits the number of times a matching entry can be logged.
|
||
#
|
||
# WARNING: IPFIREWALL defaults to a policy of "deny ip from any to any"
|
||
# and if you do not add other rules during startup to allow access,
|
||
# YOU WILL LOCK YOURSELF OUT. It is suggested that you set firewall_type=open
|
||
# in /etc/rc.conf when first enabling this feature, then refining the
|
||
# firewall rules in /etc/rc.firewall after you've tested that the new kernel
|
||
# feature works properly.
|
||
#
|
||
# IPFIREWALL_DEFAULT_TO_ACCEPT causes the default rule (at boot) to
|
||
# allow everything. Use with care, if a cracker can crash your
|
||
# firewall machine, they can get to your protected machines. However,
|
||
# if you are using it as an as-needed filter for specific problems as
|
||
# they arise, then this may be for you. Changing the default to 'allow'
|
||
# means that you won't get stuck if the kernel and /sbin/ipfw binary get
|
||
# out of sync.
|
||
#
|
||
# IPDIVERT enables the divert IP sockets, used by ``ipfw divert''
|
||
#
|
||
# IPSTEALTH enables code to support stealth forwarding (i.e., forwarding
|
||
# packets without touching the ttl). This can be useful to hide firewalls
|
||
# from traceroute and similar tools.
|
||
#
|
||
# TCPDEBUG is undocumented.
|
||
#
|
||
options TCP_COMPAT_42 #emulate 4.2BSD TCP bugs
|
||
options MROUTING # Multicast routing
|
||
options IPFIREWALL #firewall
|
||
options IPFIREWALL_VERBOSE #print information about
|
||
# dropped packets
|
||
options IPFIREWALL_FORWARD #enable transparent proxy support
|
||
options IPFIREWALL_VERBOSE_LIMIT=100 #limit verbosity
|
||
options IPFIREWALL_DEFAULT_TO_ACCEPT #allow everything by default
|
||
options IPV6FIREWALL #firewall for IPv6
|
||
options IPV6FIREWALL_VERBOSE
|
||
options IPV6FIREWALL_VERBOSE_LIMIT=100
|
||
options IPV6FIREWALL_DEFAULT_TO_ACCEPT
|
||
options IPDIVERT #divert sockets
|
||
options IPFILTER #ipfilter support
|
||
options IPFILTER_LOG #ipfilter logging
|
||
options IPSTEALTH #support for stealth forwarding
|
||
options TCPDEBUG
|
||
|
||
# The following options add sysctl variables for controlling how certain
|
||
# TCP packets are handled.
|
||
#
|
||
# TCP_DROP_SYNFIN adds support for ignoring TCP packets with SYN+FIN. This
|
||
# prevents nmap et al. from identifying the TCP/IP stack, but breaks support
|
||
# for RFC1644 extensions and is not recommended for web servers.
|
||
#
|
||
# TCP_RESTRICT_RST adds support for blocking the emission of TCP RST packets.
|
||
# This is useful on systems which are exposed to SYN floods (e.g. IRC servers)
|
||
# or any system which one does not want to be easily portscannable.
|
||
#
|
||
options TCP_DROP_SYNFIN #drop TCP packets with SYN+FIN
|
||
options TCP_RESTRICT_RST #restrict emission of TCP RST
|
||
|
||
# ICMP_BANDLIM enables icmp error response bandwidth limiting. You
|
||
# typically want this option as it will help protect the machine from
|
||
# D.O.S. packet attacks.
|
||
#
|
||
options ICMP_BANDLIM
|
||
|
||
# DUMMYNET enables the "dummynet" bandwidth limiter. You need
|
||
# IPFIREWALL as well. See the dummynet(4) manpage for more info.
|
||
# BRIDGE enables bridging between ethernet cards -- see bridge(4).
|
||
# You can use IPFIREWALL and dummynet together with bridging.
|
||
options DUMMYNET
|
||
options BRIDGE
|
||
|
||
#
|
||
# ATM (HARP version) options
|
||
#
|
||
# ATM_CORE includes the base ATM functionality code. This must be included
|
||
# for ATM support.
|
||
#
|
||
# ATM_IP includes support for running IP over ATM.
|
||
#
|
||
# At least one (and usually only one) of the following signalling managers
|
||
# must be included (note that all signalling managers include PVC support):
|
||
# ATM_SIGPVC includes support for the PVC-only signalling manager `sigpvc'.
|
||
# ATM_SPANS includes support for the `spans' signalling manager, which runs
|
||
# the FORE Systems's proprietary SPANS signalling protocol.
|
||
# ATM_UNI includes support for the `uni30' and `uni31' signalling managers,
|
||
# which run the ATM Forum UNI 3.x signalling protocols.
|
||
#
|
||
# The `hea' driver provides support for the Efficient Networks, Inc.
|
||
# ENI-155p ATM PCI Adapter.
|
||
#
|
||
# The `hfa' driver provides support for the FORE Systems, Inc.
|
||
# PCA-200E ATM PCI Adapter.
|
||
#
|
||
options ATM_CORE #core ATM protocol family
|
||
options ATM_IP #IP over ATM support
|
||
options ATM_SIGPVC #SIGPVC signalling manager
|
||
options ATM_SPANS #SPANS signalling manager
|
||
options ATM_UNI #UNI signalling manager
|
||
device hea #Efficient ENI-155p ATM PCI
|
||
device hfa #FORE PCA-200E ATM PCI
|
||
|
||
|
||
#####################################################################
|
||
# FILESYSTEM OPTIONS
|
||
|
||
#
|
||
# Only the root, /usr, and /tmp filesystems need be statically
|
||
# compiled; everything else will be automatically loaded at mount
|
||
# time. (Exception: the UFS family---FFS, and MFS --- cannot
|
||
# currently be demand-loaded.) Some people still prefer to statically
|
||
# compile other filesystems as well.
|
||
#
|
||
# NB: The NULL, PORTAL, UMAP and UNION filesystems are known to be
|
||
# buggy, and WILL panic your system if you attempt to do anything with
|
||
# them. They are included here as an incentive for some enterprising
|
||
# soul to sit down and fix them.
|
||
#
|
||
|
||
# One of these is mandatory:
|
||
options FFS #Fast filesystem
|
||
options MFS #Memory File System
|
||
options NFS #Network File System
|
||
|
||
# The rest are optional:
|
||
#options NFS_NOSERVER #Disable the NFS-server code.
|
||
options CD9660 #ISO 9660 filesystem
|
||
options FDESC #File descriptor filesystem
|
||
options KERNFS #Kernel filesystem
|
||
options MSDOSFS #MS DOS File System
|
||
options NTFS #NT File System
|
||
options NULLFS #NULL filesystem
|
||
options NWFS #NetWare filesystem
|
||
options PORTAL #Portal filesystem
|
||
options PROCFS #Process filesystem
|
||
options UMAPFS #UID map filesystem
|
||
options UNION #Union filesystem
|
||
# The xFS_ROOT options REQUIRE the associated ``options xFS''
|
||
options CD9660_ROOT #CD-ROM usable as root device
|
||
options FFS_ROOT #FFS usable as root device
|
||
options NFS_ROOT #NFS usable as root device
|
||
# This code is still experimental (e.g. doesn't handle disk slices well).
|
||
# Also, 'options MFS' is currently incompatible with DEVFS.
|
||
options DEVFS #devices filesystem
|
||
|
||
# Soft updates is technique for improving file system speed and
|
||
# making abrupt shutdown less risky. It is not enabled by default due
|
||
# to copyright restraints on the code that implement it.
|
||
#
|
||
# Read ../../ufs/ffs/README.softupdates to learn what you need to
|
||
# do to enable this. ../../contrib/softupdates/README gives
|
||
# more details on how they actually work.
|
||
#
|
||
#options SOFTUPDATES
|
||
|
||
# Make space in the kernel for a root filesystem on a md device.
|
||
# Define to the number of kilobytes to reserve for the filesystem.
|
||
options MD_ROOT_SIZE=10
|
||
|
||
# Make the md device a potential root device, either with preloaded
|
||
# images of type mfs_root or md_root.
|
||
options MD_ROOT
|
||
|
||
# Allow this many swap-devices.
|
||
options NSWAPDEV=20
|
||
|
||
# Disk quotas are supported when this option is enabled.
|
||
options QUOTA #enable disk quotas
|
||
|
||
# If you are running a machine just as a fileserver for PC and MAC
|
||
# users, using SAMBA or Netatalk, you may consider setting this option
|
||
# and keeping all those users' directories on a filesystem that is
|
||
# mounted with the suiddir option. This gives new files the same
|
||
# ownership as the directory (similar to group). It's a security hole
|
||
# if you let these users run programs, so confine it to file-servers
|
||
# (but it'll save you lots of headaches in those cases). Root owned
|
||
# directories are exempt and X bits are cleared. The suid bit must be
|
||
# set on the directory as well; see chmod(1) PC owners can't see/set
|
||
# ownerships so they keep getting their toes trodden on. This saves
|
||
# you all the support calls as the filesystem it's used on will act as
|
||
# they expect: "It's my dir so it must be my file".
|
||
#
|
||
options SUIDDIR
|
||
|
||
# NFS options:
|
||
options NFS_MINATTRTIMO=3 # VREG attrib cache timeout in sec
|
||
options NFS_MAXATTRTIMO=60
|
||
options NFS_MINDIRATTRTIMO=30 # VDIR attrib cache timeout in sec
|
||
options NFS_MAXDIRATTRTIMO=60
|
||
options NFS_GATHERDELAY=10 # Default write gather delay (msec)
|
||
options NFS_UIDHASHSIZ=29 # Tune the size of nfssvc_sock with this
|
||
options NFS_WDELAYHASHSIZ=16 # and with this
|
||
options NFS_MUIDHASHSIZ=63 # Tune the size of nfsmount with this
|
||
options NFS_DEBUG # Enable NFS Debugging
|
||
|
||
# Coda stuff:
|
||
options CODA #CODA filesystem.
|
||
pseudo-device vcoda 4 #coda minicache <-> venus comm.
|
||
|
||
#
|
||
# Add support for the EXT2FS filesystem of Linux fame. Be a bit
|
||
# careful with this - the ext2fs code has a tendency to lag behind
|
||
# changes and not be exercised very much, so mounting read/write could
|
||
# be dangerous (and even mounting read only could result in panics.)
|
||
#
|
||
options EXT2FS
|
||
|
||
# Use real implementations of the aio_* system calls. There are numerous
|
||
# stability issues in the current aio code that make it unsuitable for
|
||
# inclusion on shell boxes.
|
||
options VFS_AIO
|
||
|
||
|
||
#####################################################################
|
||
# POSIX P1003.1B
|
||
|
||
# Real time extensions added in the 1993 Posix
|
||
# P1003_1B: Infrastructure
|
||
# _KPOSIX_PRIORITY_SCHEDULING: Build in _POSIX_PRIORITY_SCHEDULING
|
||
# _KPOSIX_VERSION: Version kernel is built for
|
||
|
||
options P1003_1B
|
||
options _KPOSIX_PRIORITY_SCHEDULING
|
||
options _KPOSIX_VERSION=199309L
|
||
|
||
|
||
#####################################################################
|
||
# SCSI DEVICES
|
||
|
||
# SCSI DEVICE CONFIGURATION
|
||
|
||
# The SCSI subsystem consists of the `base' SCSI code, a number of
|
||
# high-level SCSI device `type' drivers, and the low-level host-adapter
|
||
# device drivers. The host adapters are listed in the ISA and PCI
|
||
# device configuration sections below.
|
||
#
|
||
# Beginning with FreeBSD 2.0.5 you can wire down your SCSI devices so
|
||
# that a given bus, target, and LUN always come on line as the same
|
||
# device unit. In earlier versions the unit numbers were assigned
|
||
# in the order that the devices were probed on the SCSI bus. This
|
||
# means that if you removed a disk drive, you may have had to rewrite
|
||
# your /etc/fstab file, and also that you had to be careful when adding
|
||
# a new disk as it may have been probed earlier and moved your device
|
||
# configuration around.
|
||
|
||
# This old behavior is maintained as the default behavior. The unit
|
||
# assignment begins with the first non-wired down unit for a device
|
||
# type. For example, if you wire a disk as "da3" then the first
|
||
# non-wired disk will be assigned da4.
|
||
|
||
# The syntax for wiring down devices is:
|
||
|
||
# device scbus0 at ahc0 # Single bus device
|
||
# device scbus1 at ahc1 bus 0 # Single bus device
|
||
# device scbus3 at ahc2 bus 0 # Twin bus device
|
||
# device scbus2 at ahc2 bus 1 # Twin bus device
|
||
# device da0 at scbus0 target 0 unit 0
|
||
# device da1 at scbus3 target 1
|
||
# device da2 at scbus2 target 3
|
||
# device sa1 at scbus1 target 6
|
||
# device cd
|
||
|
||
# "units" (SCSI logical unit number) that are not specified are
|
||
# treated as if specified as LUN 0.
|
||
|
||
# All SCSI devices allocate as many units as are required.
|
||
|
||
# The "unknown" device (uk? in pre-2.0.5) is now part of the base SCSI
|
||
# configuration and doesn't have to be explicitly configured.
|
||
|
||
device scbus #base SCSI code
|
||
device ch #SCSI media changers
|
||
device da #SCSI direct access devices (aka disks)
|
||
device sa #SCSI tapes
|
||
device cd #SCSI CD-ROMs
|
||
device pass #CAM passthrough driver
|
||
device pt #SCSI processor type
|
||
device ses #SCSI SES/SAF-TE driver
|
||
|
||
# CAM OPTIONS:
|
||
# debugging options:
|
||
# -- NOTE -- If you specify one of the bus/target/lun options, you must
|
||
# specify them all!
|
||
# CAMDEBUG: When defined enables debugging macros
|
||
# CAM_DEBUG_BUS: Debug the given bus. Use -1 to debug all busses.
|
||
# CAM_DEBUG_TARGET: Debug the given target. Use -1 to debug all targets.
|
||
# CAM_DEBUG_LUN: Debug the given lun. Use -1 to debug all luns.
|
||
# CAM_DEBUG_FLAGS: OR together CAM_DEBUG_INFO, CAM_DEBUG_TRACE,
|
||
# CAM_DEBUG_SUBTRACE, and CAM_DEBUG_CDB
|
||
#
|
||
# CAM_MAX_HIGHPOWER: Maximum number of concurrent high power (start unit) cmds
|
||
# SCSI_NO_SENSE_STRINGS: When defined disables sense descriptions
|
||
# SCSI_NO_OP_STRINGS: When defined disables opcode descriptions
|
||
# SCSI_DELAY: The number of MILLISECONDS to freeze the SIM (scsi adapter)
|
||
# queue after a bus reset, and the number of milliseconds to
|
||
# freeze the device queue after a bus device reset.
|
||
options CAMDEBUG
|
||
options CAM_DEBUG_BUS=-1
|
||
options CAM_DEBUG_TARGET=-1
|
||
options CAM_DEBUG_LUN=-1
|
||
options CAM_DEBUG_FLAGS="CAM_DEBUG_INFO|CAM_DEBUG_TRACE|CAM_DEBUG_CDB"
|
||
options CAM_MAX_HIGHPOWER=4
|
||
options SCSI_NO_SENSE_STRINGS
|
||
options SCSI_NO_OP_STRINGS
|
||
options SCSI_DELAY=8000 # Be pessimistic about Joe SCSI device
|
||
|
||
# Options for the CAM CDROM driver:
|
||
# CHANGER_MIN_BUSY_SECONDS: Guaranteed minimum time quantum for a changer LUN
|
||
# CHANGER_MAX_BUSY_SECONDS: Maximum time quantum per changer LUN, only
|
||
# enforced if there is I/O waiting for another LUN
|
||
# The compiled in defaults for these variables are 2 and 10 seconds,
|
||
# respectively.
|
||
#
|
||
# These can also be changed on the fly with the following sysctl variables:
|
||
# kern.cam.cd.changer.min_busy_seconds
|
||
# kern.cam.cd.changer.max_busy_seconds
|
||
#
|
||
options CHANGER_MIN_BUSY_SECONDS=2
|
||
options CHANGER_MAX_BUSY_SECONDS=10
|
||
|
||
# Options for the CAM sequential access driver:
|
||
# SA_SPACE_TIMEOUT: Timeout for space operations, in minutes
|
||
# SA_REWIND_TIMEOUT: Timeout for rewind operations, in minutes
|
||
# SA_ERASE_TIMEOUT: Timeout for erase operations, in minutes
|
||
# SA_1FM_AT_EOD: Default to model which only has a default one filemark at EOT.
|
||
options SA_SPACE_TIMEOUT="(60)"
|
||
options SA_REWIND_TIMEOUT="(2*60)"
|
||
options SA_ERASE_TIMEOUT="(4*60)"
|
||
options SA_1FM_AT_EOD
|
||
|
||
# Optional timeout for the CAM processor target (pt) device
|
||
# This is specified in seconds. The default is 60 seconds.
|
||
options SCSI_PT_DEFAULT_TIMEOUT="60"
|
||
|
||
# Optional enable of doing SES passthrough on other devices (e.g., disks)
|
||
#
|
||
# Normally disabled because a lot of newer SCSI disks report themselves
|
||
# as having SES capabilities, but this can then clot up attempts to build
|
||
# build a topology with the SES device that's on the box these drives
|
||
# are in....
|
||
options SES_ENABLE_PASSTHROUGH
|
||
|
||
|
||
#####################################################################
|
||
# MISCELLANEOUS DEVICES AND OPTIONS
|
||
|
||
# The `pty' device usually turns out to be ``effectively mandatory'',
|
||
# as it is required for `telnetd', `rlogind', `screen', `emacs', and
|
||
# `xterm', among others.
|
||
|
||
pseudo-device pty #Pseudo ttys
|
||
pseudo-device speaker #Play IBM BASIC-style noises out your speaker
|
||
pseudo-device gzip #Exec gzipped a.out's
|
||
pseudo-device vn #Vnode driver (turns a file into a device)
|
||
pseudo-device md #Memory/malloc disk
|
||
pseudo-device snp 3 #Snoop device - to look at pty/vty/etc..
|
||
pseudo-device ccd 4 #Concatenated disk driver
|
||
|
||
# Configuring Vinum into the kernel is not necessary, since the kld
|
||
# module gets started automatically when vinum(8) starts. This
|
||
# device is also untested. Use at your own risk.
|
||
#
|
||
# The option VINUMDEBUG must match the value set in CFLAGS
|
||
# in src/sbin/vinum/Makefile. Failure to do so will result in
|
||
# the following message from vinum(8):
|
||
#
|
||
# Can't get vinum config: Invalid argument
|
||
#
|
||
# see vinum(4) for more reasons not to use these options.
|
||
pseudo-device vinum #Vinum concat/mirror/raid driver
|
||
options VINUMDEBUG #enable Vinum debugging hooks
|
||
|
||
# Size of the kernel message buffer. Should be N * pagesize.
|
||
options MSGBUF_SIZE=40960
|
||
|
||
|
||
#####################################################################
|
||
# HARDWARE DEVICE CONFIGURATION
|
||
|
||
# ISA and EISA devices:
|
||
# EISA support is available for some device, so they can be auto-probed.
|
||
# MicroChannel (MCA) support is available for some devices.
|
||
|
||
#
|
||
# Mandatory ISA devices: isa, npx
|
||
#
|
||
device isa
|
||
|
||
#
|
||
# Options for `isa':
|
||
#
|
||
# AUTO_EOI_1 enables the `automatic EOI' feature for the master 8259A
|
||
# interrupt controller. This saves about 0.7-1.25 usec for each interrupt.
|
||
# This option breaks suspend/resume on some portables.
|
||
#
|
||
# AUTO_EOI_2 enables the `automatic EOI' feature for the slave 8259A
|
||
# interrupt controller. This saves about 0.7-1.25 usec for each interrupt.
|
||
# Automatic EOI is documented not to work for for the slave with the
|
||
# original i8259A, but it works for some clones and some integrated
|
||
# versions.
|
||
#
|
||
# MAXMEM specifies the amount of RAM on the machine; if this is not
|
||
# specified, FreeBSD will first read the amount of memory from the CMOS
|
||
# RAM, so the amount of memory will initially be limited to 64MB or 16MB
|
||
# depending on the BIOS. If the BIOS reports 64MB, a memory probe will
|
||
# then attempt to detect the installed amount of RAM. If this probe
|
||
# fails to detect >64MB RAM you will have to use the MAXMEM option.
|
||
# The amount is in kilobytes, so for a machine with 128MB of RAM, it would
|
||
# be 131072 (128 * 1024).
|
||
#
|
||
# BROKEN_KEYBOARD_RESET disables the use of the keyboard controller to
|
||
# reset the CPU for reboot. This is needed on some systems with broken
|
||
# keyboard controllers.
|
||
#
|
||
# PAS_JOYSTICK_ENABLE enables the gameport on the ProAudio Spectrum
|
||
|
||
options AUTO_EOI_1
|
||
#options AUTO_EOI_2
|
||
options MAXMEM="(128*1024)"
|
||
#options BROKEN_KEYBOARD_RESET
|
||
#options PAS_JOYSTICK_ENABLE
|
||
options COMPAT_OLDPCI #Use PCI shims and glue for old drivers
|
||
|
||
# Enable support for the kernel PLL to use an external PPS signal,
|
||
# under supervision of [x]ntpd(8)
|
||
# More info in ntpd documentation: http://www.eecis.udel.edu/~ntp
|
||
|
||
options PPS_SYNC
|
||
|
||
# If you see the "calcru: negative time of %ld usec for pid %d (%s)\n"
|
||
# message you probably have some broken sw/hw which disables interrupts
|
||
# for too long. You can make the system more resistant to this by
|
||
# choosing a high value for NTIMECOUNTER. The default is 5, there
|
||
# is no upper limit but more than a couple of hundred are not productive.
|
||
# A better strategy may be to sysctl -w kern.timecounter.method=1
|
||
|
||
options NTIMECOUNTER=20
|
||
|
||
# The keyboard controller; it controls the keyboard and the PS/2 mouse.
|
||
device atkbdc0 at isa? port IO_KBD
|
||
|
||
# The AT keyboard
|
||
device atkbd0 at atkbdc? irq 1
|
||
|
||
# Options for atkbd:
|
||
options ATKBD_DFLT_KEYMAP # specify the built-in keymap
|
||
makeoptions ATKBD_DFLT_KEYMAP="jp.106"
|
||
|
||
# These options are valid for other keyboard drivers as well.
|
||
options KBD_DISABLE_KEYMAP_LOAD # refuse to load a keymap
|
||
options KBD_INSTALL_CDEV # install a CDEV entry in /dev
|
||
|
||
# `flags' for atkbd:
|
||
# 0x01 Force detection of keyboard, else we always assume a keyboard
|
||
# 0x02 Don't reset keyboard, useful for some newer ThinkPads
|
||
# 0x04 Old-style (XT) keyboard support, useful for older ThinkPads
|
||
|
||
# PS/2 mouse
|
||
device psm0 at atkbdc? irq 12
|
||
|
||
# Options for psm:
|
||
options PSM_HOOKRESUME #hook the system resume event, useful
|
||
#for some laptops
|
||
options PSM_RESETAFTERSUSPEND #reset the device at the resume event
|
||
|
||
# The video card driver.
|
||
device vga0 at isa?
|
||
|
||
# Options for vga:
|
||
# Try the following option if the mouse pointer is not drawn correctly
|
||
# or font does not seem to be loaded properly. May cause flicker on
|
||
# some systems.
|
||
options VGA_ALT_SEQACCESS
|
||
|
||
# If you can dispense with some vga driver features, you may want to
|
||
# use the following options to save some memory.
|
||
options VGA_NO_FONT_LOADING # don't save/load font
|
||
options VGA_NO_MODE_CHANGE # don't change video modes
|
||
|
||
# Older video cards may require this option for proper operation.
|
||
options VGA_SLOW_IOACCESS # do byte-wide i/o's to TS and GDC regs
|
||
|
||
# The following option probably won't work with the LCD displays.
|
||
options VGA_WIDTH90 # support 90 column modes
|
||
|
||
# To include support for VESA video modes
|
||
options VESA
|
||
|
||
# Splash screen at start up! Screen savers require this too.
|
||
pseudo-device splash
|
||
|
||
# The pcvt console driver (vt220 compatible).
|
||
device vt0 at isa?
|
||
options XSERVER # support for running an X server on vt
|
||
options FAT_CURSOR # start with block cursor
|
||
# This PCVT option is for keyboards such as those used on IBM ThinkPad laptops
|
||
options PCVT_SCANSET=2 # IBM keyboards are non-std
|
||
# Other PCVT options are documented in pcvt(4).
|
||
options PCVT_24LINESDEF
|
||
options PCVT_CTRL_ALT_DEL
|
||
options PCVT_EMU_MOUSE
|
||
options PCVT_FREEBSD=211
|
||
options PCVT_META_ESC
|
||
options PCVT_NSCREENS=9
|
||
options PCVT_PRETTYSCRNS
|
||
options PCVT_SCREENSAVER
|
||
options PCVT_USEKBDSEC
|
||
options PCVT_VT220KEYB
|
||
|
||
# The syscons console driver (sco color console compatible).
|
||
device sc0 at isa?
|
||
options MAXCONS=16 # number of virtual consoles
|
||
options SC_ALT_MOUSE_IMAGE # simplified mouse cursor in text mode
|
||
options SC_DFLT_FONT # compile font in
|
||
makeoptions SC_DFLT_FONT=cp850
|
||
options SC_DISABLE_DDBKEY # disable `debug' key
|
||
options SC_DISABLE_REBOOT # disable reboot key sequence
|
||
options SC_HISTORY_SIZE=200 # number of history buffer lines
|
||
options SC_MOUSE_CHAR=0x3 # char code for text mode mouse cursor
|
||
options SC_PIXEL_MODE # add support for the raster text mode
|
||
|
||
# The following options will let you change the default colors of syscons.
|
||
options SC_NORM_ATTR="(FG_GREEN|BG_BLACK)"
|
||
options SC_NORM_REV_ATTR="(FG_YELLOW|BG_GREEN)"
|
||
options SC_KERNEL_CONS_ATTR="(FG_RED|BG_BLACK)"
|
||
options SC_KERNEL_CONS_REV_ATTR="(FG_BLACK|BG_RED)"
|
||
|
||
# If you have a two button mouse, you may want to add the following option
|
||
# to use the right button of the mouse to paste text.
|
||
options SC_TWOBUTTON_MOUSE
|
||
|
||
# You can selectively disable features in syscons.
|
||
options SC_NO_CUTPASTE
|
||
options SC_NO_FONT_LOADING
|
||
options SC_NO_HISTORY
|
||
options SC_NO_SYSMOUSE
|
||
|
||
#
|
||
# The Numeric Processing eXtension driver. In addition to this, you
|
||
# may configure a math emulator (see above). If your machine has a
|
||
# hardware FPU and the kernel configuration includes the npx device
|
||
# *and* a math emulator compiled into the kernel, the hardware FPU
|
||
# will be used, unless it is found to be broken or unless "flags" to
|
||
# npx0 includes "0x08", which requests preference for the emulator.
|
||
device npx0 at nexus? port IO_NPX flags 0x0 irq 13
|
||
|
||
#
|
||
# `flags' for npx0:
|
||
# 0x01 don't use the npx registers to optimize bcopy.
|
||
# 0x02 don't use the npx registers to optimize bzero.
|
||
# 0x04 don't use the npx registers to optimize copyin or copyout.
|
||
# 0x08 use emulator even if hardware FPU is available.
|
||
# The npx registers are normally used to optimize copying and zeroing when
|
||
# all of the following conditions are satisfied:
|
||
# I586_CPU is an option
|
||
# the cpu is an i586 (perhaps not a Pentium)
|
||
# the probe for npx0 succeeds
|
||
# INT 16 exception handling works.
|
||
# Then copying and zeroing using the npx registers is normally 30-100% faster.
|
||
# The flags can be used to control cases where it doesn't work or is slower.
|
||
# Setting them at boot time using userconfig works right (the optimizations
|
||
# are not used until later in the bootstrap when npx0 is attached).
|
||
# Flag 0x08 automatically disables the i586 optimized routines.
|
||
#
|
||
|
||
#
|
||
# Optional ISA and EISA devices:
|
||
#
|
||
|
||
#
|
||
# SCSI host adapters: `aha', `aic', `bt'
|
||
#
|
||
# adv: All Narrow SCSI bus AdvanSys controllers.
|
||
# adw: Second Generation AdvanSys controllers including the ADV940UW.
|
||
# aha: Adaptec 154x
|
||
# ahc: Adaptec 274x/284x/294x
|
||
# aic: Adaptec 152x
|
||
# bt: Most Buslogic controllers
|
||
#
|
||
# Note that the order is important in order for Buslogic cards to be
|
||
# probed correctly.
|
||
#
|
||
|
||
device bt0 at isa? port IO_BT0
|
||
device adv0 at isa?
|
||
device adw
|
||
device aha0 at isa?
|
||
device aic0 at isa?
|
||
|
||
#
|
||
# Compaq Smart RAID, Mylex DAC960 and AMI MegaRAID controllers. Only
|
||
# one entry is needed; the code will find and configure all supported
|
||
# controllers.
|
||
#
|
||
device ida # Compaq Smart RAID
|
||
device mlx # Mylex DAC960
|
||
device amr # AMI MegaRAID
|
||
|
||
#
|
||
# The 'ATA' driver supports all ATA and ATAPI devices.
|
||
# You only need one "device ata" for it to find all
|
||
# PCI ATA/ATAPI devices on modern machines.
|
||
device ata
|
||
device atadisk # ATA disk drives
|
||
device atapicd # ATAPI CDROM drives
|
||
device atapifd # ATAPI floppy drives
|
||
device atapist # ATAPI tape drives
|
||
|
||
#
|
||
#The following options are valid on the ATA driver:
|
||
#
|
||
# ATA_STATIC_ID: controller numbering is static ie depends on location
|
||
# else the device numbers are dynamically allocated.
|
||
# ATA_ENABLE_ATAPI_DMA: enable DMA on ATAPI device, since many ATAPI devices
|
||
# claim to support DMA but doesn't actually work, this
|
||
# is not enabled as default.
|
||
|
||
options ATA_STATIC_ID
|
||
options ATA_ENABLE_ATAPI_DMA
|
||
|
||
#
|
||
# For older non-PCI systems, these are the lines to use:
|
||
#device ata0 at isa? port IO_WD1 irq 14
|
||
#device ata1 at isa? port IO_WD2 irq 15
|
||
|
||
#
|
||
# Standard floppy disk controllers and floppy tapes: `fdc', `fd', and `ft'
|
||
#
|
||
device fdc0 at isa? port IO_FD1 irq 6 drq 2
|
||
#
|
||
# FDC_DEBUG enables floppy debugging. Since the debug output is huge, you
|
||
# gotta turn it actually on by setting the variable fd_debug with DDB,
|
||
# however.
|
||
options FDC_DEBUG
|
||
#
|
||
# Activate this line instead of the fdc0 line above if you happen to
|
||
# have an Insight floppy tape. Probing them proved to be dangerous
|
||
# for people with floppy disks only, so it's "hidden" behind a flag:
|
||
#device fdc0 at isa? port IO_FD1 flags 1 irq 6 drq 2
|
||
|
||
device fd0 at fdc0 drive 0
|
||
device fd1 at fdc0 drive 1
|
||
|
||
# M-systems DiskOnchip products see src/sys/contrib/dev/fla/README
|
||
device fla0 at isa?
|
||
|
||
#
|
||
# Other standard PC hardware: `mse', `sio', etc.
|
||
#
|
||
# mse: Logitech and ATI InPort bus mouse ports
|
||
# sio: serial ports (see sio(4))
|
||
|
||
device mse0 at isa? port 0x23c irq 5
|
||
|
||
device sio0 at isa? port IO_COM1 flags 0x10 irq 4
|
||
|
||
#
|
||
# `flags' for serial drivers that support consoles (only for sio now):
|
||
# 0x10 enable console support for this unit. The other console flags
|
||
# are ignored unless this is set. Enabling console support does
|
||
# not make the unit the preferred console - boot with -h or set
|
||
# the 0x20 flag for that. Currently, at most one unit can have
|
||
# console support; the first one (in config file order) with
|
||
# this flag set is preferred. Setting this flag for sio0 gives
|
||
# the old behaviour.
|
||
# 0x20 force this unit to be the console (unless there is another
|
||
# higher priority console). This replaces the COMCONSOLE option.
|
||
# 0x40 reserve this unit for low level console operations. Do not
|
||
# access the device in any normal way.
|
||
# 0x80 use this port for serial line gdb support in ddb.
|
||
#
|
||
# PnP `flags' (set via userconfig using pnp x flags y)
|
||
# 0x1 disable probing of this device. Used to prevent your modem
|
||
# from being attached as a PnP modem.
|
||
#
|
||
|
||
# Options for serial drivers that support consoles (only for sio now):
|
||
options BREAK_TO_DEBUGGER #a BREAK on a comconsole goes to
|
||
#DDB, if available.
|
||
options CONSPEED=9600 #default speed for serial console (default 9600)
|
||
|
||
# Options for sio:
|
||
options COM_ESP #code for Hayes ESP
|
||
options COM_MULTIPORT #code for some cards with shared IRQs
|
||
|
||
# Other flags for sio that aren't documented in the man page.
|
||
# 0x20000 enable hardware RTS/CTS and larger FIFOs. Only works for
|
||
# ST16650A-compatible UARTs.
|
||
|
||
#
|
||
# Network interfaces: `cx', `ed', `el', `ep', `ie', `is', `le', `lnc'
|
||
#
|
||
# ar: Arnet SYNC/570i hdlc sync 2/4 port V.35/X.21 serial driver (requires sppp)
|
||
# cs: IBM Etherjet and other Crystal Semi CS89x0-based adapters
|
||
# cx: Cronyx/Sigma multiport sync/async (with Cisco or PPP framing)
|
||
# ed: Western Digital and SMC 80xx; Novell NE1000 and NE2000; 3Com 3C503
|
||
# el: 3Com 3C501 (slow!)
|
||
# ep: 3Com 3C509
|
||
# ex: Intel EtherExpress Pro/10 and other i82595-based adapters
|
||
# fe: Fujitsu MB86960A/MB86965A Ethernet
|
||
# ie: AT&T StarLAN 10 and EN100; 3Com 3C507; unknown NI5210; Intel EtherExpress
|
||
# le: Digital Equipment EtherWorks 2 and EtherWorks 3 (DEPCA, DE100,
|
||
# DE101, DE200, DE201, DE202, DE203, DE204, DE205, DE422)
|
||
# lnc: Lance/PCnet cards (Isolan, Novell NE2100, NE32-VL, AMD Am7990 & Am79C960)
|
||
# rdp: RealTek RTL 8002-based pocket ethernet adapters
|
||
# sr: RISCom/N2 hdlc sync 1/2 port V.35/X.21 serial driver (requires sppp)
|
||
# wl: Lucent Wavelan (ISA card only).
|
||
# wi: Lucent WaveLAN/IEEE 802.11 PCMCIA adapters. Note: this supports both
|
||
# the PCMCIA and ISA cards: the ISA card is really a PCMCIA to ISA
|
||
# bridge with a PCMCIA adapter plugged into it.
|
||
# an: Aironet 4500/4800 802.11 wireless adapters. Supports the PCMCIA,
|
||
# PCI and ISA varieties.
|
||
# xe: Xircom/Intel EtherExpress Pro100/16 PC Card ethernet controller.
|
||
# oltr: Olicom ISA token-ring adapters OC-3115, OC-3117, OC-3118 and OC-3133
|
||
# (no options needed)
|
||
#
|
||
device ar0 at isa? port 0x300 irq 10 iomem 0xd0000
|
||
device cs0 at isa? port 0x300
|
||
device cx0 at isa? port 0x240 irq 15 drq 7
|
||
device ed0 at isa? port 0x280 irq 5 iomem 0xd8000
|
||
device el0 at isa? port 0x300 irq 9
|
||
device ep
|
||
device ex
|
||
device fe0 at isa? port 0x300
|
||
device ie0 at isa? port 0x300 irq 5 iomem 0xd0000
|
||
device ie1 at isa? port 0x360 irq 7 iomem 0xd0000
|
||
device le0 at isa? port 0x300 irq 5 iomem 0xd0000
|
||
device lnc0 at isa? port 0x280 irq 10 drq 0
|
||
device rdp0 at isa? port 0x378 irq 7 flags 2
|
||
device sr0 at isa? port 0x300 irq 5 iomem 0xd0000
|
||
device sn0 at isa? port 0x300 irq 10
|
||
device wi
|
||
device an
|
||
options WLCACHE # enables the signal-strength cache
|
||
options WLDEBUG # enables verbose debugging output
|
||
device wl0 at isa? port 0x300
|
||
device xe0 at isa?
|
||
|
||
device oltr0 at isa?
|
||
|
||
#
|
||
# ATM related options
|
||
#
|
||
# The `en' device provides support for Efficient Networks (ENI)
|
||
# ENI-155 PCI midway cards, and the Adaptec 155Mbps PCI ATM cards (ANA-59x0).
|
||
#
|
||
# atm pseudo-device provides generic atm functions and is required for
|
||
# atm devices.
|
||
# NATM enables the netnatm protocol family that can be used to
|
||
# bypass TCP/IP.
|
||
#
|
||
# the current driver supports only PVC operations (no atm-arp, no multicast).
|
||
# for more details, please read the original documents at
|
||
# http://www.ccrc.wustl.edu/pub/chuck/tech/bsdatm/bsdatm.html
|
||
#
|
||
pseudo-device atm
|
||
device en
|
||
options NATM #native ATM
|
||
|
||
#
|
||
# Audio drivers: `snd', `sb', `pas', `gus', `pca'
|
||
#
|
||
# snd: Voxware sound support code
|
||
# sb: SoundBlaster PCM - SoundBlaster, SB Pro, SB16, ProAudioSpectrum
|
||
# sbxvi: SoundBlaster 16
|
||
# sbmidi: SoundBlaster 16 MIDI interface
|
||
# pas: ProAudioSpectrum PCM and MIDI
|
||
# gus: Gravis Ultrasound - Ultrasound, Ultrasound 16, Ultrasound MAX
|
||
# gusxvi: Gravis Ultrasound 16-bit PCM (do not use)
|
||
# mss: Microsoft Sound System
|
||
# css: Crystal Sound System (CSS 423x PnP)
|
||
# sscape: Ensoniq Soundscape MIDI interface
|
||
# sscape_mss: Ensoniq Soundscape PCM (requires sscape)
|
||
# opl: Yamaha OPL-2 and OPL-3 FM - SB, SB Pro, SB 16, ProAudioSpectrum
|
||
# uart: stand-alone 6850 UART for MIDI
|
||
# mpu: Roland MPU-401 stand-alone card
|
||
#
|
||
# Note: It has been reported that ISA DMA with the SoundBlaster will
|
||
# lock up the machine (PR docs/5358). If this happens to you,
|
||
# turning off USWC write posting in your machine's BIOS may fix
|
||
# the problem.
|
||
#
|
||
# Beware! The addresses specified below are also hard-coded in
|
||
# src/sys/i386/isa/sound/sound_config.h. If you change the values here, you
|
||
# must also change the values in the include file.
|
||
#
|
||
# pcm: PCM audio through various sound cards.
|
||
#
|
||
# This has support for a large number of new audio cards, based on
|
||
# CS423x, OPTi931, Yamaha OPL-SAx, and also for SB16, GusPnP.
|
||
# For more information about this driver and supported cards,
|
||
# see the pcm.4 man page.
|
||
#
|
||
# The flags of the device tells the device a bit more info about the
|
||
# device that normally is obtained through the PnP interface.
|
||
# bit 2..0 secondary DMA channel;
|
||
# bit 4 set if the board uses two dma channels;
|
||
# bit 15..8 board type, overrides autodetection; leave it
|
||
# zero if don't know what to put in (and you don't,
|
||
# since this is unsupported at the moment...).
|
||
#
|
||
# This driver will use the new PnP code if it's available.
|
||
#
|
||
# pca: PCM audio through your PC speaker
|
||
#
|
||
# If you have a GUS-MAX card and want to use the CS4231 codec on the
|
||
# card the drqs for the gus max must be 8 bit (1, 2, or 3).
|
||
#
|
||
# If you would like to use the full duplex option on the gus, then define
|
||
# flags to be the ``read dma channel''.
|
||
#
|
||
# options BROKEN_BUS_CLOCK #PAS-16 isn't working and OPTI chipset
|
||
# options SYMPHONY_PAS #PAS-16 isn't working and SYMPHONY chipset
|
||
# options EXCLUDE_SBPRO #PAS-16
|
||
# options SBC_IRQ=5 #PAS-16. Must match irq on sb0 line.
|
||
# PAS16: The order of the pas0/sb0/opl0 is important since the
|
||
# sb emulation is enabled in the pas-16 attach.
|
||
#
|
||
# To override the GUS defaults use:
|
||
# options GUS_DMA2
|
||
# options GUS_DMA
|
||
# options GUS_IRQ
|
||
#
|
||
# The src/sys/i386/isa/sound/sound.doc has more information.
|
||
|
||
# Controls all "VOXWARE" driver sound devices. See Luigi's driver
|
||
# below for an alternate which may work better for some cards.
|
||
#
|
||
#device snd
|
||
#device pas0 at isa? port 0x388 irq 10 drq 6
|
||
#device sb0 at isa? port 0x220 irq 5 drq 1
|
||
#device sbxvi0 at isa? drq 5
|
||
#device sbmidi0 at isa? port 0x330
|
||
#device awe0 at isa? port 0x620
|
||
#device gus0 at isa? port 0x220 irq 12 drq 1
|
||
##device gus0 at isa? port 0x220 irq 12 drq 1 flags 0x3
|
||
#device mss0 at isa? port 0x530 irq 10 drq 1
|
||
#device css0 at isa? port 0x534 irq 5 drq 1 flags 0x08
|
||
#device sscape0 at isa? port 0x330 irq 9 drq 0
|
||
#device trix0 at isa? port 0x330 irq 6 drq 0
|
||
#device sscape_mss0 at isa? port 0x534 irq 5 drq 1
|
||
#device opl0 at isa? port 0x388
|
||
#device mpu0 at isa? port 0x330 irq 6 drq 0
|
||
#device uart0 at isa? port 0x330 irq 5
|
||
|
||
# The newpcm driver (use INSTEAD of snd0 and all VOXWARE drivers!).
|
||
# Note that motherboard sound devices may require options PNPBIOS.
|
||
#
|
||
# Supported cards include:
|
||
# Creative SoundBlaster ISA PnP/non-PnP
|
||
# Supports ESS and Avance ISA chips as well.
|
||
# Gravis UltraSound ISA PnP/non-PnP
|
||
# Crystal Semiconductor CS461x/428x PCI
|
||
# Neomagic 256AV (ac97)
|
||
# Most of the more common ISA/PnP sb/mss/ess compatable cards.
|
||
|
||
# For non-pnp sound cards with no bridge drivers only:
|
||
device pcm0 at isa? irq 10 drq 1 flags 0x0
|
||
#
|
||
# For PnP/PCI sound cards
|
||
device pcm
|
||
|
||
# The bridge drivers for sound cards. These can be seperately configured
|
||
# for providing services to the likes of new-midi (not in the tree yet).
|
||
# When used with 'device pcm' they also provide pcm sound services.
|
||
#
|
||
# sbc: Creative SoundBlaster ISA PnP/non-PnP
|
||
# Supports ESS and Avance ISA chips as well.
|
||
# gusc: Gravis UltraSound ISA PnP/non-PnP
|
||
# csa: Crystal Semiconductor CS461x/428x PCI
|
||
|
||
# For non-PnP cards:
|
||
device sbc0 at isa? port 0x220 irq 5 drq 1 flags 0x15
|
||
device gusc0 at isa? port 0x220 irq 5 drq 1 flags 0x13
|
||
|
||
# Not controlled by `snd'
|
||
device pca0 at isa? port IO_TIMER1
|
||
|
||
#
|
||
# Miscellaneous hardware:
|
||
#
|
||
# mcd: Mitsumi CD-ROM
|
||
# scd: Sony CD-ROM
|
||
# matcd: Matsushita/Panasonic CD-ROM
|
||
# wt: Wangtek and Archive QIC-02/QIC-36 tape drives
|
||
# ctx: Cortex-I frame grabber
|
||
# apm: Laptop Advanced Power Management (experimental)
|
||
# spigot: The Creative Labs Video Spigot video-acquisition board
|
||
# meteor: Matrox Meteor video capture board
|
||
# bktr: Brooktree bt848/848a/849a/878/879 video capture and TV Tuner board
|
||
# cy: Cyclades serial driver
|
||
# dgb: Digiboard PC/Xi and PC/Xe series driver (ALPHA QUALITY!)
|
||
# dgm: Digiboard PC/Xem driver
|
||
# gp: National Instruments AT-GPIB and AT-GPIB/TNT board
|
||
# asc: GI1904-based hand scanners, e.g. the Trust Amiscan Grey
|
||
# gsc: Genius GS-4500 hand scanner.
|
||
# joy: joystick
|
||
# labpc: National Instrument's Lab-PC and Lab-PC+
|
||
# rc: RISCom/8 multiport card
|
||
# rp: Comtrol Rocketport(ISA) - single card
|
||
# tw: TW-523 power line interface for use with X-10 home control products
|
||
# si: Specialix SI/XIO 4-32 port terminal multiplexor
|
||
# stl: Stallion EasyIO and EasyConnection 8/32 (cd1400 based)
|
||
# stli: Stallion EasyConnection 8/64, ONboard, Brumby (intelligent)
|
||
|
||
# Notes on APM
|
||
# The flags takes the following meaning for apm0:
|
||
# 0x0020 Statclock is broken.
|
||
# If apm is omitted, some systems require sysctl -w kern.timecounter.method=1
|
||
# for correct timekeeping.
|
||
|
||
# Notes on the spigot:
|
||
# The video spigot is at 0xad6. This port address can not be changed.
|
||
# The irq values may only be 10, 11, or 15
|
||
# I/O memory is an 8kb region. Possible values are:
|
||
# 0a0000, 0a2000, ..., 0fffff, f00000, f02000, ..., ffffff
|
||
# The start address must be on an even boundary.
|
||
# Add the following option if you want to allow non-root users to be able
|
||
# to access the spigot. This option is not secure because it allows users
|
||
# direct access to the I/O page.
|
||
# options SPIGOT_UNSECURE
|
||
|
||
# Notes on the Comtrol Rocketport driver:
|
||
#
|
||
# The exact values used for rp0 depend on how many boards you have
|
||
# in the system. The manufacturer's sample configs are listed as:
|
||
#
|
||
# Comtrol Rocketport ISA single card
|
||
# device rp0 at isa? port 0x280
|
||
#
|
||
# If instead you have two ISA cards, one installed at 0x100 and the
|
||
# second installed at 0x180, then you should add the following to
|
||
# your kernel configuration file:
|
||
#
|
||
# device rp0 at isa? port 0x100
|
||
# device rp1 at isa? port 0x180
|
||
#
|
||
# For 4 ISA cards, it might be something like this:
|
||
#
|
||
# device rp0 at isa? port 0x180
|
||
# device rp1 at isa? port 0x100
|
||
# device rp2 at isa? port 0x340
|
||
# device rp3 at isa? port 0x240
|
||
#
|
||
# And for PCI cards, you only need say:
|
||
#
|
||
# device rp
|
||
|
||
# Notes on the Digiboard driver:
|
||
#
|
||
# The following flag values have special meanings:
|
||
# 0x01 - alternate layout of pins (dgb & dgm)
|
||
# 0x02 - use the windowed PC/Xe in 64K mode (dgb only)
|
||
|
||
# Notes on the Specialix SI/XIO driver:
|
||
# **This is NOT a Specialix supported Driver!**
|
||
# The host card is memory, not IO mapped.
|
||
# The Rev 1 host cards use a 64K chunk, on a 32K boundary.
|
||
# The Rev 2 host cards use a 32K chunk, on a 32K boundary.
|
||
# The cards can use an IRQ of 11, 12 or 15.
|
||
|
||
# Notes on the Stallion stl and stli drivers:
|
||
# See src/i386/isa/README.stl for complete instructions.
|
||
# This is version 0.0.5alpha, unsupported by Stallion.
|
||
# The stl driver has a secondary IO port hard coded at 0x280. You need
|
||
# to change src/i386/isa/stallion.c if you reconfigure this on the boards.
|
||
# The "flags" and "iosiz" settings on the stli driver depend on the board:
|
||
# EasyConnection 8/64 ISA: flags 23 iosiz 0x1000
|
||
# EasyConnection 8/64 EISA: flags 24 iosiz 0x10000
|
||
# EasyConnection 8/64 MCA: flags 25 iosiz 0x1000
|
||
# ONboard ISA: flags 4 iosiz 0x10000
|
||
# ONboard EISA: flags 7 iosiz 0x10000
|
||
# ONboard MCA: flags 3 iosiz 0x10000
|
||
# Brumby: flags 2 iosiz 0x4000
|
||
# Stallion: flags 1 iosiz 0x10000
|
||
|
||
device mcd0 at isa? port 0x300 irq 10
|
||
# for the Sony CDU31/33A CDROM
|
||
device scd0 at isa? port 0x230
|
||
# for the SoundBlaster 16 multicd - up to 4 devices
|
||
device matcd0 at isa? port 0x230
|
||
device wt0 at isa? port 0x300 irq 5 drq 1
|
||
device ctx0 at isa? port 0x230 iomem 0xd0000
|
||
device spigot0 at isa? port 0xad6 irq 15 iomem 0xee000
|
||
device apm0
|
||
device gp0 at isa? port 0x2c0
|
||
device gsc0 at isa? port IO_GSC1 drq 3
|
||
device joy0 at isa? port IO_GAME
|
||
device cy0 at isa? irq 10 iomem 0xd4000 iosiz 0x2000
|
||
options CY_PCI_FASTINTR # Use with cy_pci unless irq is shared
|
||
device dgb0 at isa? port 0x220 iomem 0xfc000
|
||
options NDGBPORTS=16 # Defaults to 16*NDGB
|
||
device dgm0 at isa? port 0x104 iomem 0xd0000
|
||
device labpc0 at isa? port 0x260 irq 5
|
||
device rc0 at isa? port 0x220 irq 12
|
||
device rp0 at isa? port 0x280
|
||
# the port and irq for tw0 are fictitious
|
||
device tw0 at isa? port 0x380 irq 11
|
||
device si0 at isa? iomem 0xd0000 irq 12
|
||
device asc0 at isa? port IO_ASC1 drq 3 irq 10
|
||
device stl0 at isa? port 0x2a0 irq 10
|
||
device stli0 at isa? port 0x2a0 iomem 0xcc000 flags 23 iosiz 0x1000
|
||
# You are unlikely to have the hardware for loran0 <phk@FreeBSD.org>
|
||
device loran0 at isa? irq 5
|
||
# HOT1 Xilinx 6200 card (http://www.vcc.com/)
|
||
device xrpu
|
||
|
||
#
|
||
# MCA devices:
|
||
#
|
||
# The MCA bus device is `mca'. It provides auto-detection and
|
||
# configuration support for all devices on the MCA bus.
|
||
#
|
||
# The 'aha' device provides support for the Adaptec 1640
|
||
#
|
||
# The 'bt' device provides support for various Buslogic/Bustek
|
||
# and Storage Dimensions SCSI adapters.
|
||
#
|
||
# The 'ep' device provides support for the 3Com 3C529 ethernet card.
|
||
#
|
||
device mca
|
||
|
||
#
|
||
# EISA devices:
|
||
#
|
||
# The EISA bus device is `eisa'. It provides auto-detection and
|
||
# configuration support for all devices on the EISA bus.
|
||
#
|
||
# The `ahb' device provides support for the Adaptec 174X adapter.
|
||
#
|
||
# The `ahc' device provides support for the Adaptec 274X and 284X
|
||
# adapters. The 284X, although a VLB card, responds to EISA probes.
|
||
#
|
||
# fea: DEC DEFEA EISA FDDI adapter
|
||
#
|
||
device eisa
|
||
device ahb
|
||
device ahc
|
||
device fea
|
||
|
||
# The aic7xxx driver will attempt to use memory mapped I/O for all PCI
|
||
# controllers that have it configured only if this option is set. Unfortunately,
|
||
# this doesn't work on some motherboards, which prevents it from being the
|
||
# default.
|
||
options AHC_ALLOW_MEMIO
|
||
|
||
# The adw driver will attempt to use memory mapped I/O for all PCI
|
||
# controllers that have it configured only if this option is set.
|
||
options ADW_ALLOW_MEMIO
|
||
|
||
# By default, only 10 EISA slots are probed, since the slot numbers
|
||
# above clash with the configuration address space of the PCI subsystem,
|
||
# and the EISA probe is not very smart about this. This is sufficient
|
||
# for most machines, but in particular the HP NetServer LC series comes
|
||
# with an onboard AIC7770 dual-channel SCSI controller on EISA slot #11,
|
||
# thus you need to bump this figure to 12 for them.
|
||
options EISA_SLOTS=12
|
||
|
||
#
|
||
# PCI devices & PCI options:
|
||
#
|
||
# The main PCI bus device is `pci'. It provides auto-detection and
|
||
# configuration support for all devices on the PCI bus, using either
|
||
# configuration mode defined in the PCI specification.
|
||
|
||
device pci
|
||
|
||
# PCI options
|
||
#
|
||
#options PCI_QUIET #quiets PCI code on chipset settings
|
||
options COMPAT_OLDPCI #Use PCI shims and glue for old drivers
|
||
|
||
|
||
# The `ahc' device provides support for the Adaptec 29/3940(U)(W)
|
||
# and motherboard based AIC7870/AIC7880 adapters.
|
||
#
|
||
# The `amd' device provides support for the AMD 53C974 SCSI host
|
||
# adapter chip as found on devices such as the Tekram DC-390(T).
|
||
#
|
||
# The `ncr' device provides support for the NCR 53C810 and 53C825
|
||
# self-contained SCSI host adapters.
|
||
#
|
||
# The `isp' device provides support for the Qlogic ISP 1020, 1040
|
||
# nd 1040B PCI SCSI host adapters, ISP 1240 Dual Ultra SCSI,
|
||
# ISP 1080 and 1280 (Dual) Ultra2, ISP 12160 Ultra3 SCSI, as well as
|
||
# the Qlogic ISP 2100 and ISP 2200 Fibre Channel Host Adapters.
|
||
#
|
||
# The `dc' device provides support for PCI fast ethernet adapters
|
||
# based on the DEC/Intel 21143 and various workalikes including:
|
||
# the ADMtek AL981 Comet and AN985 Centaur, the ASIX Electronics
|
||
# AX88140A and AX88141, the Davicom DM9100 and DM9102, the Lite-On
|
||
# 82c168 and 82c169 PNIC, the Lite-On/Macronix LC82C115 PNIC II
|
||
# and the Macronix 98713/98713A/98715/98715A/98725 PMAC. This driver
|
||
# replaces the old al, ax, dm, pn and mx drivers. List of brands:
|
||
# Digital DE500-BA, Kingston KNE100TX, D-Link DFE-570TX, SOHOware SFA110,
|
||
# SVEC PN102-TX, CNet Pro110B, 120A, and 120B, Compex RL100-TX,
|
||
# LinkSys LNE100TX, LNE100TX V2.0, Jaton XpressNet, Alfa Inc GFC2204,
|
||
# KNE110TX.
|
||
#
|
||
# The `de' device provides support for the Digital Equipment DC21040
|
||
# self-contained Ethernet adapter.
|
||
#
|
||
# The `fxp' device provides support for the Intel EtherExpress Pro/100B
|
||
# PCI Fast Ethernet adapters.
|
||
#
|
||
# The 'rl' device provides support for PCI fast ethernet adapters based
|
||
# on the RealTek 8129/8139 chipset. Note that the RealTek driver defaults
|
||
# to using programmed I/O to do register accesses because memory mapped
|
||
# mode seems to cause severe lockups on SMP hardware. This driver also
|
||
# supports the Accton EN1207D `Cheetah' adapter, which uses a chip called
|
||
# the MPX 5030/5038, which is either a RealTek in disguise or a RealTek
|
||
# workalike. Note that the D-Link DFE-530TX+ uses the RealTek chipset
|
||
# and is supported by this driver, not the 'vr' driver.
|
||
#
|
||
# The 'sf' device provides support for Adaptec Duralink PCI fast
|
||
# ethernet adapters based on the Adaptec AIC-6915 "starfire" controller.
|
||
# This includes dual and quad port cards, as well as one 100baseFX card.
|
||
# Most of these are 64-bit PCI devices, except for one single port
|
||
# card which is 32-bit.
|
||
#
|
||
# The 'ste' device provides support for adapters based on the Sundance
|
||
# Technologies ST201 PCI fast ethernet controller. This includes the
|
||
# D-Link DFE-550TX.
|
||
#
|
||
# The 'sis' device provides support for adapters based on the Silicon
|
||
# Integrated Systems SiS 900 and SiS 7016 PCI fast ethernet controller
|
||
# chips.
|
||
#
|
||
# The 'sk' device provides support for the SysKonnect SK-984x series
|
||
# PCI gigabit ethernet NICs. This includes the SK-9841 and SK-9842
|
||
# single port cards (single mode and multimode fiber) and the
|
||
# SK-9843 and SK-9844 dual port cards (also single mode and multimode).
|
||
# The driver will autodetect the number of ports on the card and
|
||
# attach each one as a separate network interface.
|
||
#
|
||
# The 'ti' device provides support for PCI gigabit ethernet NICs based
|
||
# on the Alteon Networks Tigon 1 and Tigon 2 chipsets. This includes the
|
||
# Alteon AceNIC, the 3Com 3c985, the Netgear GA620 and various others.
|
||
# Note that you will probably want to bump up NMBCLUSTERS a lot to use
|
||
# this driver.
|
||
#
|
||
# The 'tl' device provides support for the Texas Instruments TNETE100
|
||
# series 'ThunderLAN' cards and integrated ethernet controllers. This
|
||
# includes several Compaq Netelligent 10/100 cards and the built-in
|
||
# ethernet controllers in several Compaq Prosignia, Proliant and
|
||
# Deskpro systems. It also supports several Olicom 10Mbps and 10/100
|
||
# boards.
|
||
#
|
||
# The `tx' device provides support for the SMC 9432TX cards.
|
||
#
|
||
# The `vr' device provides support for various fast ethernet adapters
|
||
# based on the VIA Technologies VT3043 `Rhine I' and VT86C100A `Rhine II'
|
||
# chips, including the D-Link DFE530TX (see 'rl' for DFE530TX+), the Hawking
|
||
# Technologies PN102TX, and the AOpen/Acer ALN-320.
|
||
#
|
||
# The `vx' device provides support for the 3Com 3C590 and 3C595
|
||
# early support
|
||
#
|
||
# The `wb' device provides support for various fast ethernet adapters
|
||
# based on the Winbond W89C840F chip. Note: this is not the same as
|
||
# the Winbond W89C940F, which is an NE2000 clone.
|
||
#
|
||
# The `wx' device provides support for the Intel Gigabit Ethernet
|
||
# PCI card (`Wiseman').
|
||
#
|
||
# The `xl' device provides support for the 3Com 3c900, 3c905 and
|
||
# 3c905B (Fast) Etherlink XL cards and integrated controllers. This
|
||
# includes the integrated 3c905B-TX chips in certain Dell Optiplex and
|
||
# Dell Precision desktop machines and the integrated 3c905-TX chips
|
||
# in Dell Latitude laptop docking stations.
|
||
#
|
||
# The `fpa' device provides support for the Digital DEFPA PCI FDDI
|
||
# adapter. pseudo-device fddi is also needed.
|
||
#
|
||
# The `meteor' device is a PCI video capture board. It can also have the
|
||
# following options:
|
||
# options METEOR_ALLOC_PAGES=xxx preallocate kernel pages for data entry
|
||
# figure (ROWS*COLUMN*BYTES_PER_PIXEL*FRAME+PAGE_SIZE-1)/PAGE_SIZE
|
||
# options METEOR_DEALLOC_PAGES remove all allocated pages on close(2)
|
||
# options METEOR_DEALLOC_ABOVE=xxx remove all allocated pages above the
|
||
# specified amount. If this value is below the allocated amount no action
|
||
# taken
|
||
# options METEOR_SYSTEM_DEFAULT={METEOR_PAL|METEOR_NTSC|METEOR_SECAM}, used
|
||
# for initialization of fps routine when a signal is not present.
|
||
#
|
||
# The 'bktr' device is a PCI video capture device using the Brooktree
|
||
# bt848/bt848a/bt849a/bt878/bt879 chipset. When used with a TV Tuner it forms a
|
||
# TV card, eg Miro PC/TV, Hauppauge WinCast/TV WinTV, VideoLogic Captivator,
|
||
# Intel Smart Video III, AverMedia, IMS Turbo, FlyVideo.
|
||
#
|
||
# options OVERRIDE_CARD=xxx
|
||
# options OVERRIDE_TUNER=xxx
|
||
# options OVERRIDE_MSP=1
|
||
# options OVERRIDE_DBX=1
|
||
# These options can be used to override the auto detection
|
||
# The current values for xxx are found in src/sys/dev/bktr/bktr_card.h
|
||
# Using sysctl(8) run-time overrides on a per-card basis can be made
|
||
#
|
||
# options BROOKTREE_SYSTEM_DEFAULT=BROOKTREE_PAL
|
||
# or
|
||
# options BROOKTREE_SYSTEM_DEFAULT=BROOKTREE_NTSC
|
||
# Specifes the default video capture mode.
|
||
# This is required for Dual Crystal (28&35Mhz) boards where PAL is used
|
||
# to prevent hangs during initialisation. eg VideoLogic Captivator PCI.
|
||
#
|
||
# options BKTR_USE_PLL
|
||
# PAL or SECAM users who have a 28Mhz crystal (and no 35Mhz crystal)
|
||
# must enable PLL mode with this option. eg some new Bt878 cards.
|
||
#
|
||
# options BKTR_GPIO_ACCESS
|
||
# This enable IOCTLs which give user level access to the GPIO port.
|
||
#
|
||
# options BKTR_NO_MSP_RESET
|
||
# Prevents the MSP34xx reset. Good if you initialise the MSP in another OS first
|
||
#
|
||
# options BKTR_430_FX_MODE
|
||
# Switch Bt878/879 cards into Intel 430FX chipset compatibility mode.
|
||
#
|
||
# options BKTR_SIS_VIA_MODE
|
||
# Switch Bt878/879 cards into SIS/VIA chipset compatibility mode which is
|
||
# needed for some old SiS and VIA chipset motherboards.
|
||
# This also allows Bt878/879 chips to work on old OPTi (<1997) chipset
|
||
# motherboards and motherboards with bad or incomplete PCI 2.1 support.
|
||
# As a rough guess, old = before 1998
|
||
#
|
||
#
|
||
# The oltr driver supports the following Olicom PCI token-ring adapters
|
||
# OC-3136, OC-3137, OC-3139, OC-3140, OC-3141, OC-3540, OC-3250
|
||
#
|
||
device ahc # AHA2940 and onboard AIC7xxx devices
|
||
device amd # AMD 53C974 (Teckram DC-390(T))
|
||
device isp # Qlogic family
|
||
device ncr # NCR/Symbios Logic
|
||
device sym # NCR/Symbios Logic (newer chipsets)
|
||
#
|
||
# Options for ISP
|
||
#
|
||
# SCSI_ISP_NO_FWLOAD_MASK - mask of isp unit numbers (obviously
|
||
# a max of 32) that you wish to disable
|
||
# to disable the loading of firmware on.
|
||
# SCSI_ISP_NO_NVRAM_MASK - mask of isp unit numbers (obviously
|
||
# a max of 32) that you wish to disable
|
||
# them picking up information from NVRAM
|
||
# (for broken cards you can't fix the NVRAM
|
||
# on- very rare, or for systems you can't
|
||
# change NVRAM on (e.g. alpha) and you don't
|
||
# like what's in there)
|
||
# SCSI_ISP_PREFER_MEM_MAP - control preference for using memory mappings
|
||
# instead of I/O space mappings. It defaults
|
||
# to 1 for i386, 0 for alpha. Set to 1 to
|
||
# unconditionally prefer mapping memory,
|
||
# else it will use I/O space mappings. Of
|
||
# course, this can fail if the PCI implement-
|
||
# ation doesn't support what you want.
|
||
#
|
||
# SCSI_ISP_FCDUPLEX - mask of isp unit numbers (obviously
|
||
# a max of 32) that you wish to set fibre
|
||
# channel full duplex mode on.
|
||
# to disable the loading of firmware on.
|
||
# SCSI_ISP_FABRIC enable loading of Fabric f/w flavor (2100).
|
||
# SCSI_ISP_SCCLUN enable loading of expanded lun f/w (2100).
|
||
# SCSI_ISP_WWN - define a WWN to use as a default
|
||
#
|
||
# ISP_DISABLE_1020_SUPPORT Disable support for 1020/1040 cards
|
||
# ISP_DISABLE_1080_SUPPORT Disable support for 1080/1240 cards
|
||
# ISP_DISABLE_12160_SUPPORT Disable support for 12160 cards
|
||
# ISP_DISABLE_2100_SUPPORT Disable support for 2100 cards
|
||
# (these really just to save some code space)
|
||
# (use of all four will cause the kernel to not compile)
|
||
#
|
||
# ISP_COMPILE_FW - compile all firmware in
|
||
# ISP_COMPILE_1020_FW - compile in 1020/1040 firmware
|
||
# ISP_COMPILE_1080_FW - compile in 1080/1240/1280 firmware
|
||
# ISP_COMPILE_12160_FW - compile in 12160 firmware
|
||
# ISP_COMPILE_2100_FW - compile in 2100 firmware
|
||
# ISP_COMPILE_2200_FW - compile in 2200 firmware
|
||
#
|
||
# ISP_TARGET_MODE - enable target mode operation
|
||
#
|
||
options SCSI_ISP_NO_FWLOAD_MASK=0x12 # disable FW load for isp1, isp4
|
||
options SCSI_ISP_NO_NVRAM_MASK=0x1 # disable NVRAM for isp0
|
||
options SCSI_ISP_PREFER_MEM_MAP=0 # prefer I/O mapping
|
||
options SCSI_ISP_FCDUPLEX=0x4 # isp2 is a Fibre Channel card
|
||
# we want in full duplex mode.
|
||
options SCSI_ISP_WWN="0x5000000099990000"
|
||
#options ISP_DISABLE_1020_SUPPORT
|
||
#options ISP_DISABLE_1080_SUPPORT
|
||
#options ISP_DISABLE_12160_SUPPORT
|
||
#options ISP_DISABLE_2100_SUPPORT
|
||
#options ISP_COMPILE_1020_FW=1
|
||
#options ISP_COMPILE_1080_FW=1
|
||
#options ISP_COMPILE_2100_FW=1
|
||
#options ISP_COMPILE_2200_FW=1
|
||
#options ISP_TARGET_MODE=1
|
||
|
||
# Options used in dev/sym/ (Symbios SCSI driver).
|
||
#options SYM_SETUP_LP_PROBE_MAP #-Low Priority Probe Map (bits)
|
||
# Allows the ncr to take precedence
|
||
# 1 (1<<0) -> 810a, 860
|
||
# 2 (1<<1) -> 825a, 875, 885, 895
|
||
# 4 (1<<2) -> 895a, 896, 1510d
|
||
#options SYM_SETUP_SCSI_DIFF #-HVD support for 825a, 875, 885
|
||
# disabled:0 (default), enabled:1
|
||
#options SYM_SETUP_PCI_PARITY #-PCI parity checking
|
||
# disabled:0, enabled:1 (default)
|
||
#options SYM_SETUP_MAX_LUN #-Number of LUNs supported
|
||
# default:8, range:[1..64]
|
||
|
||
|
||
# MII bus support is required for some PCI 10/100 ethernet NICs,
|
||
# namely those which use MII-compliant transceivers or implement
|
||
# tranceiver control interfaces that operate like an MII. Adding
|
||
# "device miibus0" to the kernel config pulls in support for
|
||
# the generic miibus API and all of the PHY drivers, including a
|
||
# generic one for PHYs that aren't specifically handled by an
|
||
# individual driver.
|
||
device miibus
|
||
|
||
# PCI Ethernet NICs that use the common MII bus controller code.
|
||
device dc # DEC/Intel 21143 and various workalikes
|
||
device rl # RealTek 8129/8139
|
||
device sf # Adaptec AIC-6915 (``Starfire'')
|
||
device sis # Silicon Integrated Systems SiS 900/SiS 7016
|
||
device ste # Sundance ST201 (D-Link DFE-550TX)
|
||
device tl # Texas Instruments ThunderLAN
|
||
device vr # VIA Rhine, Rhine II
|
||
device wb # Winbond W89C840F
|
||
device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'')
|
||
|
||
# PCI Ethernet NICs.
|
||
device de # DEC/Intel DC21x4x (``Tulip'')
|
||
device fxp # Intel EtherExpress PRO/100B (82557, 82558)
|
||
device tx # SMC 9432TX (83c170 ``EPIC'')
|
||
device vx # 3Com 3c590, 3c595 (``Vortex'')
|
||
|
||
device sk
|
||
device ti
|
||
device wx
|
||
device fpa
|
||
device meteor
|
||
#The oltr driver in the ISA section will also find PCI cards.
|
||
#device oltr0
|
||
|
||
|
||
# Brooktree driver has been ported to the new I2C framework. Thus,
|
||
# you'll need to have the following 3 lines in the kernel config.
|
||
# device smbus
|
||
# device iicbus
|
||
# device iicbb
|
||
# The iic and smb devices are only needed if you want to control other
|
||
# I2C slaves connected to the external connector of some cards.
|
||
#
|
||
device bktr
|
||
|
||
#
|
||
# PCCARD/PCMCIA
|
||
#
|
||
# card: pccard slots
|
||
# pcic: isa/pccard bridge
|
||
device pcic0 at isa?
|
||
device pcic1 at isa?
|
||
device card
|
||
|
||
# You may need to reset all pccards after resuming
|
||
options PCIC_RESUME_RESET # reset after resume
|
||
|
||
#
|
||
# Laptop/Notebook options:
|
||
#
|
||
# See also:
|
||
# apm under `Miscellaneous hardware'
|
||
# above.
|
||
|
||
# For older notebooks that signal a powerfail condition (external
|
||
# power supply dropped, or battery state low) by issuing an NMI:
|
||
|
||
options POWERFAIL_NMI # make it beep instead of panicing
|
||
|
||
#
|
||
# SMB bus
|
||
#
|
||
# System Management Bus support provided by the 'smbus' device.
|
||
#
|
||
# Supported devices:
|
||
# smb standard io
|
||
#
|
||
# Supported interfaces:
|
||
# iicsmb I2C to SMB bridge with any iicbus interface
|
||
# bktr brooktree848 I2C hardware interface
|
||
# intpm Intel PIIX4 Power Management Unit
|
||
# alpm Acer Aladdin-IV/V/Pro2 Power Management Unit
|
||
#
|
||
device smbus # Bus support, required for smb below.
|
||
device intpm
|
||
device alpm
|
||
|
||
device smb
|
||
|
||
#
|
||
# I2C Bus
|
||
#
|
||
# Philips i2c bus support is provided by the `iicbus' device.
|
||
#
|
||
# Supported devices:
|
||
# ic i2c network interface
|
||
# iic i2c standard io
|
||
# iicsmb i2c to smb bridge. Allow i2c i/o with smb commands.
|
||
#
|
||
# Supported interfaces:
|
||
# pcf Philips PCF8584 ISA-bus controller
|
||
# bktr brooktree848 I2C software interface
|
||
#
|
||
# Other:
|
||
# iicbb generic I2C bit-banging code (needed by lpbb, bktr)
|
||
#
|
||
device iicbus # Bus support, required for ic/iic/iicsmb below.
|
||
device iicbb
|
||
|
||
device ic
|
||
device iic
|
||
device iicsmb # smb over i2c bridge
|
||
|
||
device pcf0 at isa? port 0x320 irq 5
|
||
|
||
# ISDN4BSD section
|
||
#
|
||
# See /usr/share/examples/isdn/ROADMAP for an introduction to isdn4bsd.
|
||
#
|
||
# i4b passive ISDN cards support (isic - I4b Siemens Isdn Chipset driver)
|
||
# note that the ``options'' and ``device'' lines must BOTH be defined !
|
||
#
|
||
# Driver entries marked "(not supported yet!)" are not working currently
|
||
# due to not being converted to newbus. We hope to get them back to support
|
||
# in the near future.
|
||
#
|
||
# ISA bus non-PnP Cards:
|
||
# ----------------------
|
||
#
|
||
# Teles S0/8 or Niccy 1008
|
||
options TEL_S0_8
|
||
device isic0 at isa? iomem 0xd0000 irq 5 flags 1
|
||
#
|
||
# Teles S0/16 or Creatix ISDN-S0 or Niccy 1016
|
||
options TEL_S0_16
|
||
#device isic0 at isa? port 0xd80 iomem 0xd0000 irq 5 flags 2
|
||
#
|
||
# Teles S0/16.3
|
||
options TEL_S0_16_3
|
||
#device isic0 at isa? port 0xd80 irq 5 flags 3
|
||
#
|
||
# AVM A1 or AVM Fritz!Card
|
||
options AVM_A1
|
||
#device isic0 at isa? port 0x340 irq 5 flags 4
|
||
#
|
||
# USRobotics Sportster ISDN TA intern (not supported yet!)
|
||
#options USR_STI
|
||
#device isic0 at isa? port 0x268 irq 5 flags 7
|
||
#
|
||
# ITK ix1 Micro ( < V.3, non-PnP version ) (not supported yet!)
|
||
#options ITKIX1
|
||
#device isic0 at isa? port 0x398 irq 10 flags 18
|
||
#
|
||
# ELSA PCC-16
|
||
options ELSA_PCC16
|
||
#device isic0 at isa? port 0x360 irq 10 flags 20
|
||
#
|
||
# ISA bus PnP Cards:
|
||
# ------------------
|
||
#
|
||
# Teles S0/16.3 PnP
|
||
options TEL_S0_16_3_P
|
||
#device isic
|
||
#
|
||
# Creatix ISDN-S0 P&P
|
||
options CRTX_S0_P
|
||
#device isic
|
||
#
|
||
# Dr. Neuhaus Niccy Go@
|
||
options DRN_NGO
|
||
#device isic
|
||
#
|
||
# Sedlbauer Win Speed
|
||
options SEDLBAUER
|
||
#device isic
|
||
#
|
||
# Dynalink IS64PH (not supported yet!)
|
||
#options DYNALINK
|
||
#device isic
|
||
#
|
||
# ELSA QuickStep 1000pro ISA
|
||
options ELSA_QS1ISA
|
||
#device isic
|
||
#
|
||
# ITK ix1 Micro ( V.3, PnP version ) (not supported yet!)
|
||
#options ITKIX1
|
||
#device isic
|
||
#
|
||
# AVM Fritz!Card PnP (not supported yet!)
|
||
#options AVM_PNP
|
||
#device isic
|
||
#
|
||
# Siemens I-Surf 2.0
|
||
options SIEMENS_ISURF2
|
||
#device isic
|
||
#
|
||
# Asuscom ISDNlink 128K ISAC - broken
|
||
#options ASUSCOM_IPAC
|
||
#device isic
|
||
#
|
||
# PCI bus Cards:
|
||
# --------------
|
||
#
|
||
# ELSA MicroLink ISDN/PCI (same as ELSA QuickStep 1000pro PCI)
|
||
options ELSA_QS1PCI
|
||
#device isic
|
||
#
|
||
# AVM Fritz!Card PCI
|
||
options AVM_A1_PCI
|
||
#device isic
|
||
#
|
||
# PCMCIA Cards:
|
||
# -------------
|
||
#
|
||
# AVM PCMCIA Fritz!Card (not supported yet!)
|
||
#options AVM_A1_PCMCIA
|
||
#device isic0 at isa? port 0x340 irq 5 flags 10
|
||
#
|
||
# Active Cards:
|
||
# -------------
|
||
#
|
||
# Stollmann Tina-dd control device
|
||
# (driver under development, not fully functional!)
|
||
device tina0 at isa? port 0x260 irq 10
|
||
#
|
||
# ISDN Protocol Stack
|
||
# -------------------
|
||
#
|
||
# Q.921 / layer 2 - i4b passive cards D channel handling
|
||
pseudo-device "i4bq921"
|
||
#
|
||
# Q.931 / layer 3 - i4b passive cards D channel handling
|
||
pseudo-device "i4bq931"
|
||
#
|
||
# layer 4 - i4b common passive and active card handling
|
||
pseudo-device "i4b"
|
||
#
|
||
# ISDN devices
|
||
# ------------
|
||
#
|
||
# userland driver to do ISDN tracing (for passive cards only)
|
||
pseudo-device "i4btrc" 4
|
||
#
|
||
# userland driver to control the whole thing
|
||
pseudo-device "i4bctl"
|
||
#
|
||
# userland driver for access to raw B channel
|
||
pseudo-device "i4brbch" 4
|
||
#
|
||
# userland driver for telephony
|
||
pseudo-device "i4btel" 2
|
||
#
|
||
# network driver for IP over raw HDLC ISDN
|
||
pseudo-device "i4bipr" 4
|
||
# enable VJ header compression detection for ipr i/f
|
||
options IPR_VJ
|
||
# enable logging of the first n IP packets to isdnd (n=32 here)
|
||
#options IPR_LOG=32
|
||
#
|
||
# network driver for sync PPP over ISDN
|
||
pseudo-device "i4bisppp" 4
|
||
|
||
|
||
# Parallel-Port Bus
|
||
#
|
||
# Parallel port bus support is provided by the `ppbus' device.
|
||
# Multiple devices may be attached to the parallel port, devices
|
||
# are automatically probed and attached when found.
|
||
#
|
||
# Supported devices:
|
||
# vpo Iomega Zip Drive
|
||
# Requires SCSI disk support ('scbus' and 'da'), best
|
||
# performance is achieved with ports in EPP 1.9 mode.
|
||
# lpt Parallel Printer
|
||
# plip Parallel network interface
|
||
# ppi General-purpose I/O ("Geek Port") + IEEE1284 I/O
|
||
# pps Pulse per second Timing Interface
|
||
# lpbb Philips official parallel port I2C bit-banging interface
|
||
#
|
||
# Supported interfaces:
|
||
# ppc ISA-bus parallel port interfaces.
|
||
#
|
||
|
||
options PPC_PROBE_CHIPSET # Enable chipset specific detection
|
||
# (see flags in ppc(4))
|
||
options DEBUG_1284 # IEEE1284 signaling protocol debug
|
||
options PERIPH_1284 # Makes your computer act as a IEEE1284
|
||
# compliant peripheral
|
||
options DONTPROBE_1284 # Avoid boot detection of PnP parallel devices
|
||
options VP0_DEBUG # ZIP/ZIP+ debug
|
||
options LPT_DEBUG # Printer driver debug
|
||
options PPC_DEBUG # Parallel chipset level debug
|
||
options PLIP_DEBUG # Parallel network IP interface debug
|
||
options PCFCLOCK_VERBOSE # Verbose pcfclock driver
|
||
options PCFCLOCK_MAX_RETRIES=5 # Maximum read tries (default 10)
|
||
|
||
device ppc0 at isa? irq 7
|
||
device ppbus
|
||
device vpo
|
||
device lpt
|
||
device plip
|
||
device ppi
|
||
device pps
|
||
device lpbb
|
||
device pcfclock
|
||
|
||
# Kernel BOOTP support
|
||
|
||
options BOOTP # Use BOOTP to obtain IP address/hostname
|
||
options BOOTP_NFSROOT # NFS mount root filesystem using BOOTP info
|
||
options BOOTP_NFSV3 # Use NFS v3 to NFS mount root
|
||
options BOOTP_COMPAT # Workaround for broken bootp daemons.
|
||
options BOOTP_WIRED_TO=fxp0 # Use interface fxp0 for BOOTP
|
||
|
||
#
|
||
# Add tie-ins for a hardware watchdog. This only enable the hooks;
|
||
# the user must still supply the actual driver.
|
||
#
|
||
options HW_WDOG
|
||
|
||
#
|
||
# Set the number of PV entries per process. Increasing this can
|
||
# stop panics related to heavy use of shared memory. However, that can
|
||
# (combined with large amounts of physical memory) cause panics at
|
||
# boot time due the kernel running out of VM space.
|
||
#
|
||
# If you're tweaking this, you might also want to increase the sysctls
|
||
# "vm.v_free_min", "vm.v_free_reserved", and "vm.v_free_target".
|
||
#
|
||
# The value below is the one more than the default.
|
||
#
|
||
options PMAP_SHPGPERPROC=201
|
||
|
||
#
|
||
# Disable swapping. This option removes all code which actually performs
|
||
# swapping, so it's not possible to turn it back on at run-time.
|
||
#
|
||
# This is sometimes usable for systems which don't have any swap space
|
||
# (see also sysctls "vm.defer_swapspace_pageouts" and
|
||
# "vm.disable_swapspace_pageouts")
|
||
#
|
||
#options NO_SWAPPING
|
||
|
||
# Set the number of sf_bufs to allocate. sf_bufs are virtual buffers
|
||
# for sendfile(2) that are used to map file VM pages, and normally
|
||
# default to a quantity that is roughly 16*MAXUSERS+512. You would
|
||
# typically want about 4 of these for each simultaneous file send.
|
||
#
|
||
options NSFBUFS=1024
|
||
|
||
#
|
||
# Enable extra debugging code for locks. This stores the filename and
|
||
# line of whatever acquired the lock in the lock itself, and change a
|
||
# number of function calls to pass around the relevant data. This is
|
||
# not at all useful unless you are debugging lock code. Also note
|
||
# that it is likely to break e.g. fstat(1) unless you recompile your
|
||
# userland with -DDEBUG_LOCKS as well.
|
||
#
|
||
options DEBUG_LOCKS
|
||
|
||
#
|
||
# SysVR4 ABI emulation
|
||
#
|
||
# The svr4 ABI emulator can be statically compiled into the kernel or loaded as
|
||
# a KLD module.
|
||
# The STREAMS network emulation code can also be compiled statically or as a
|
||
# module. If loaded as a module, it must be loaded before the svr4 module
|
||
# (the /usr/sbin/svr4 script does this for you). If compiling statically,
|
||
# the `streams' pseudo-device must be configured into any kernel which also
|
||
# specifies COMPAT_SVR4. It is possible to have a statically-configured
|
||
# STREAMS device and a dynamically loadable svr4 emulator; the /usr/sbin/svr4
|
||
# script understands that it doesn't need to load the `streams' module under
|
||
# those circumstances.
|
||
# Caveat: At this time, `options KTRACE' is required for the svr4 emulator
|
||
# (whether static or dynamic).
|
||
#
|
||
options COMPAT_SVR4 # build emulator statically
|
||
options DEBUG_SVR4 # enable verbose debugging
|
||
pseudo-device streams # STREAMS network driver (required for svr4).
|
||
|
||
# The 'dpt' driver provides support for DPT controllers (http://www.dpt.com/).
|
||
# These have hardware RAID-{0,1,5} support, and do multi-initiator I/O.
|
||
# The DPT controllers are commonly re-licensed under other brand-names -
|
||
# some controllers by Olivetti, Dec, HP, AT&T, SNI, AST, Alphatronic, NEC and
|
||
# Compaq are actually DPT controllers.
|
||
#
|
||
# See src/sys/dev/dpt for debugging and other subtle options.
|
||
# DPT_MEASURE_PERFORMANCE Enables a set of (semi)invasive metrics. Various
|
||
# instruments are enabled. The tools in
|
||
# /usr/sbin/dpt_* assume these to be enabled.
|
||
# DPT_HANDLE_TIMEOUTS Normally device timeouts are handled by the DPT.
|
||
# If you ant the driver to handle timeouts, enable
|
||
# this option. If your system is very busy, this
|
||
# option will create more trouble than solve.
|
||
# DPT_TIMEOUT_FACTOR Used to compute the excessive amount of time to
|
||
# wait when timing out with the above option.
|
||
# DPT_DEBUG_xxxx These are controllable from sys/dev/dpt/dpt.h
|
||
# DPT_LOST_IRQ When enabled, will try, once per second, to catch
|
||
# any interrupt that got lost. Seems to help in some
|
||
# DPT-firmware/Motherboard combinations. Minimal
|
||
# cost, great benefit.
|
||
# DPT_RESET_HBA Make "reset" actually reset the controller
|
||
# instead of fudging it. Only enable this if you
|
||
# are 100% certain you need it.
|
||
|
||
device dpt
|
||
|
||
# DPT options
|
||
#!CAM# options DPT_MEASURE_PERFORMANCE
|
||
#!CAM# options DPT_HANDLE_TIMEOUTS
|
||
options DPT_TIMEOUT_FACTOR=4
|
||
options DPT_LOST_IRQ
|
||
options DPT_RESET_HBA
|
||
options DPT_ALLOW_MEMIO
|
||
|
||
# USB support
|
||
# UHCI controller
|
||
device uhci
|
||
# OHCI controller
|
||
device ohci
|
||
# General USB code (mandatory for USB)
|
||
device usb
|
||
#
|
||
# Generic USB device driver
|
||
device ugen
|
||
# Human Interface Device (anything with buttons and dials)
|
||
device uhid
|
||
# USB keyboard
|
||
device ukbd
|
||
# USB printer
|
||
device ulpt
|
||
# USB Iomega Zip 100 Drive
|
||
device umass
|
||
# USB mouse
|
||
device ums
|
||
# Diamond Rio 500 Mp3 player
|
||
device urio
|
||
#
|
||
# ADMtek USB ethernet. Supports the LinkSys USB100TX,
|
||
# the Billionton USB100, the Melco LU-ATX, the D-Link DSB-650TX
|
||
# and the SMC 2202USB. Also works with the ADMtek AN986 Pegasus
|
||
# eval board.
|
||
device aue
|
||
#
|
||
# CATC USB-EL1201A USB ethernet. Supports the CATC Netmate
|
||
# and Netmate II, and the Belkin F5U111.
|
||
device cue
|
||
#
|
||
# Kawasaki LSI ethernet. Supports the LinkSys USB10T,
|
||
# Entrega USB-NET-E45, Peracom Ethernet Adapter, the
|
||
# 3Com 3c19250, the ADS Technologies USB-10BT, the ATen UC10T,
|
||
# the Netgear EA101, the D-Link DSB-650, the SMC 2102USB
|
||
# and 2104USB, and the Corega USB-T.
|
||
device kue
|
||
|
||
# debugging options for the USB subsystem
|
||
#
|
||
options UHCI_DEBUG
|
||
options OHCI_DEBUG
|
||
options USB_DEBUG
|
||
|
||
options UGEN_DEBUG
|
||
options UHID_DEBUG
|
||
options UHUB_DEBUG
|
||
options UKBD_DEBUG
|
||
options ULPT_DEBUG
|
||
options UMASS_DEBUG
|
||
options UMS_DEBUG
|
||
options URIO_DEBUG
|
||
|
||
# options for ukbd:
|
||
options UKBD_DFLT_KEYMAP # specify the built-in keymap
|
||
makeoptions UKBD_DFLT_KEYMAP=it.iso
|
||
|
||
#
|
||
# Embedded system options:
|
||
#
|
||
# An embedded system might want to run something other than init.
|
||
options INIT_PATH="/sbin/init:/stand/sysinstall"
|
||
|
||
# Debug options
|
||
options BUS_DEBUG # enable newbus debugging
|
||
options DEBUG_VFS_LOCKS # enable vfs lock debugging
|
||
options NPX_DEBUG # enable npx debugging (FPU/math emu)
|
||
|
||
# More undocumented options for linting.
|
||
# Note that documenting these are not considered an affront.
|
||
|
||
options AHC_DUMP_EEPROM
|
||
options AHC_TMODE_ENABLE
|
||
options CAM_DEBUG_DELAY
|
||
options CLK_CALIBRATION_LOOP
|
||
options CLK_USE_I8254_CALIBRATION
|
||
options CLK_USE_TSC_CALIBRATION
|
||
options CLUSTERDEBUG
|
||
options COMPAT_LINUX
|
||
options CPU_UPGRADE_HW_CACHE
|
||
options DEBUG
|
||
options DEBUG_LINUX
|
||
#options DISABLE_PSE
|
||
options ENABLE_ALART
|
||
options ENABLE_VFS_IOOPT
|
||
options FB_DEBUG
|
||
options FB_INSTALL_CDEV
|
||
options FE_8BIT_SUPPORT
|
||
options I4B_SMP_WORKAROUND
|
||
options I586_PMC_GUPROF=0x70000
|
||
options IBCS2
|
||
options KBDIO_DEBUG=2
|
||
options KBD_MAXRETRY=4
|
||
options KBD_MAXWAIT=6
|
||
options KBD_RESETDELAY=201
|
||
options KEY
|
||
options LOCKF_DEBUG
|
||
options LOUTB
|
||
options MSGMNB=2049
|
||
options MSGMNI=41
|
||
options MSGSEG=2049
|
||
options MSGSSZ=16
|
||
options MSGTQL=41
|
||
options NBUF=512
|
||
options NETATALKDEBUG
|
||
options NMBCLUSTERS=1024
|
||
#options OLTR_NO_BULLSEYE_MAC
|
||
#options OLTR_NO_HAWKEYE_MAC
|
||
#options OLTR_NO_TMS_MAC
|
||
options PANIC_REBOOT_WAIT_TIME=16
|
||
options PNPBIOS
|
||
options PSM_DEBUG=1
|
||
options SCSI_NCR_DEBUG
|
||
options SCSI_NCR_MAX_SYNC=10000
|
||
options SCSI_NCR_MAX_WIDE=1
|
||
options SCSI_NCR_MYADDR=7
|
||
options SC_DEBUG_LEVEL
|
||
options SC_RENDER_DEBUG
|
||
options SEMMAP=31
|
||
options SEMMNI=11
|
||
options SEMMNS=61
|
||
options SEMMNU=31
|
||
options SEMMSL=61
|
||
options SEMOPM=101
|
||
options SEMUME=11
|
||
options SHMALL=1025
|
||
options SHMMAX="(SHMMAXPGS*PAGE_SIZE+1)"
|
||
options SHMMAXPGS=1025
|
||
options SHMMIN=2
|
||
options SHMMNI=33
|
||
options SHMSEG=9
|
||
options SHOW_BUSYBUFS # List buffers that prevent root unmount
|
||
options SIMPLELOCK_DEBUG
|
||
options SI_DEBUG
|
||
options SLIP_IFF_OPTS
|
||
options SPX_HACK
|
||
options TIMER_FREQ="((14318182+6)/12)"
|
||
options VFS_BIO_DEBUG
|
||
options VM_KMEM_SIZE
|
||
options VM_KMEM_SIZE_MAX
|
||
options VM_KMEM_SIZE_SCALE
|