freebsd-skq/sys/i386/isa/atapi.h
msmith 0dd728f28c Don't use INTR when only one device supports it.
Submitted by:	Satoh Junichi <junichi@astec.co.jp>
1998-04-13 17:45:56 +00:00

303 lines
14 KiB
C

/*
* Device-independent level for ATAPI drivers.
*
* Copyright (C) 1995 Cronyx Ltd.
* Author Serge Vakulenko, <vak@cronyx.ru>
*
* This software is distributed with NO WARRANTIES, not even the implied
* warranties for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
*
* Authors grant any other persons or organizations permission to use
* or modify this software as long as this message is kept with the software,
* all derivative works or modified versions.
*
* Version 1.9, Thu Oct 12 15:53:50 MSK 1995
*/
/*
* Disk Controller ATAPI register definitions.
*/
#ifdef PC98
#define AR_DATA 0x0 /* RW - data register (16 bits) */
#define AR_ERROR 0x2 /* R - error register */
#define AR_FEATURES 0x2 /* W - features */
#define AR_IREASON 0x4 /* RW - interrupt reason */
#define AR_TAG 0x6 /* - reserved for SAM TAG byte */
#define AR_CNTLO 0x8 /* RW - byte count, low byte */
#define AR_CNTHI 0xa /* RW - byte count, high byte */
#define AR_DRIVE 0xc /* RW - drive select */
#define AR_COMMAND 0xe /* W - command register */
#define AR_STATUS 0xe /* R - immediate status */
#else
#define AR_DATA 0x0 /* RW - data register (16 bits) */
#define AR_ERROR 0x1 /* R - error register */
#define AR_FEATURES 0x1 /* W - features */
#define AR_IREASON 0x2 /* RW - interrupt reason */
#define AR_TAG 0x3 /* - reserved for SAM TAG byte */
#define AR_CNTLO 0x4 /* RW - byte count, low byte */
#define AR_CNTHI 0x5 /* RW - byte count, high byte */
#define AR_DRIVE 0x6 /* RW - drive select */
#define AR_COMMAND 0x7 /* W - command register */
#define AR_STATUS 0x7 /* R - immediate status */
#endif
/*
* Status register bits
*/
#define ARS_CHECK 0x01 /* error occured, see sense key/code */
/* bit 0x02 reserved */
#define ARS_CORR 0x04 /* correctable error occured */
#define ARS_DRQ 0x08 /* data request / ireason valid */
#define ARS_DSC 0x10 /* immediate operation completed */
#define ARS_DF 0x20 /* drive fault */
#define ARS_DRDY 0x40 /* ready to get command */
#define ARS_BSY 0x80 /* registers busy */
/* for overlap mode only: */
#define ARS_SERVICE 0x10 /* service is requested */
#define ARS_DMARDY 0x20 /* ready to start a DMA transfer */
#define ARS_BITS "\20\010busy\7ready\6fault\5opdone\4drq\3corr\1check"
/*
* Error register bits
*/
#define AER_ILI 0x01 /* illegal length indication */
#define AER_EOM 0x02 /* end of media detected */
#define AER_ABRT 0x04 /* command aborted */
#define AER_MCR 0x08 /* media change requested */
#define AER_SKEY 0xf0 /* sense key mask */
#define AER_SK_NO_SENSE 0x00 /* no specific sense key info */
#define AER_SK_RECOVERED_ERROR 0x10 /* command succeeded, data recovered */
#define AER_SK_NOT_READY 0x20 /* no access to drive */
#define AER_SK_MEDIUM_ERROR 0x30 /* non-recovered data error */
#define AER_SK_HARDWARE_ERROR 0x40 /* non-recoverable hardware failure */
#define AER_SK_ILLEGAL_REQUEST 0x50 /* invalid command parameter(s) */
#define AER_SK_UNIT_ATTENTION 0x60 /* media changed */
#define AER_SK_DATA_PROTECT 0x70 /* reading read-protected sector */
#define AER_SK_BLANK_CHECK 0x80 /* blank check */
#define AER_SK_VENDOR_SPECIFIC 0x90 /* vendor specific skey */
#define AER_SK_COPY_ABORTED 0xa0 /* copy aborted */
#define AER_SK_ABORTED_COMMAND 0xb0 /* command aborted, try again */
#define AER_SK_EQUAL 0xc0 /* equal */
#define AER_SK_VOLUME_OVERFLOW 0xd0 /* volume overflow */
#define AER_SK_MISCOMPARE 0xe0 /* data did not match the medium */
#define AER_SK_RESERVED 0xf0
#define AER_BITS "\20\4mchg\3abort\2eom\1ili"
/*
* Feature register bits
*/
#define ARF_DMA 0x01 /* transfer data via DMA */
#define ARF_OVERLAP 0x02 /* release the bus until completion */
/*
* Interrupt reason register bits
*/
#define ARI_CMD 0x01 /* command(1) or data(0) */
#define ARI_IN 0x02 /* transfer to(1) or from(0) the host */
#define ARI_RELEASE 0x04 /* bus released until completion */
/*
* Drive register values
*/
#define ARD_DRIVE0 0xa0 /* drive 0 selected */
#define ARD_DRIVE1 0xb0 /* drive 1 selected */
/*
* ATA commands
*/
#define ATAPIC_IDENTIFY 0xa1 /* get drive parameters */
#define ATAPIC_PACKET 0xa0 /* execute packet command */
/*
* Mandatory packet commands
*/
#define ATAPI_TEST_UNIT_READY 0x00 /* check if the device is ready */
#define ATAPI_REQUEST_SENSE 0x03 /* get sense data */
#define ATAPI_START_STOP 0x1b /* start/stop the media */
#define ATAPI_PREVENT_ALLOW 0x1e /* prevent/allow media removal */
#define ATAPI_READ_CAPACITY 0x25 /* get volume capacity */
#define ATAPI_READ_BIG 0x28 /* read data */
#define ATAPI_WRITE_BIG 0x2a /* write data */
#define ATAPI_READ_TOC 0x43 /* get table of contents */
#define ATAPI_READ_SUBCHANNEL 0x42 /* get subchannel info */
#define ATAPI_MODE_SELECT_BIG 0x55 /* set device parameters */
#define ATAPI_MODE_SENSE 0x5a /* get device parameters */
#define ATAPI_PLAY_CD 0xb4 /* universal play command */
#define ATAPI_MECH_STATUS 0xbd /* get changer mechanism status */
#define ATAPI_LOAD_UNLOAD 0xa6 /* changer control command */
/*
* Optional packet commands
*/
#define ATAPI_PLAY_MSF 0x47 /* play by MSF address */
#define ATAPI_PAUSE 0x4b /* stop/start audio operation */
/*
* Nonstandard packet commands
*/
#define ATAPI_PLAY_TRACK 0x48 /* play by track number */
#define ATAPI_PLAY_BIG 0xa5 /* play by logical block address */
#define DSC_POLL_INTERVAL 10
/*
* Drive parameter information
*/
struct atapi_params {
unsigned cmdsz : 2; /* packet command size */
#define AT_PSIZE_12 0 /* 12 bytes */
#define AT_PSIZE_16 1 /* 16 bytes */
unsigned : 3;
unsigned drqtype : 2; /* DRQ type */
#define AT_DRQT_MPROC 0 /* microprocessor DRQ - 3 msec delay */
#define AT_DRQT_INTR 1 /* interrupt DRQ - 10 msec delay */
#define AT_DRQT_ACCEL 2 /* accelerated DRQ - 50 usec delay */
unsigned removable : 1; /* device is removable */
unsigned devtype : 5; /* device type */
#define AT_TYPE_DIRECT 0 /* direct-access (magnetic disk) */
#define AT_TYPE_TAPE 1 /* streaming tape (QIC-121 model) */
#define AT_TYPE_CDROM 5 /* CD-ROM device */
#define AT_TYPE_OPTICAL 7 /* optical disk */
unsigned : 1;
unsigned proto : 2; /* command protocol */
#define AT_PROTO_ATAPI 2
short reserved1[9];
char serial[20]; /* serial number - optional */
short reserved2[3];
char revision[8]; /* firmware revision */
char model[40]; /* model name */
short reserved3[2];
u_char vendor_cap; /* vendor unique capabilities */
unsigned dmaflag : 1; /* DMA supported */
unsigned lbaflag : 1; /* LBA supported - always 1 */
unsigned iordydis : 1; /* IORDY can be disabled */
unsigned iordyflag : 1; /* IORDY supported */
unsigned : 1;
unsigned ovlapflag : 1; /* overlap operation supported */
unsigned : 1;
unsigned idmaflag : 1; /* interleaved DMA supported */
short reserved4;
u_short pio_timing; /* PIO cycle timing */
u_short dma_timing; /* DMA cycle timing */
u_short flags;
#define AT_FLAG_54_58 1 /* words 54-58 valid */
#define AT_FLAG_64_70 2 /* words 64-70 valid */
short reserved5[8];
u_char swdma_flag; /* singleword DMA mode supported */
u_char swdma_active; /* singleword DMA mode active */
u_char mwdma_flag; /* multiword DMA mode supported */
u_char mwdma_active; /* multiword DMA mode active */
u_char apio_flag; /* advanced PIO mode supported */
u_char reserved6;
u_short mwdma_min; /* min. M/W DMA time per word (ns) */
u_short mwdma_dflt; /* recommended M/W DMA time (ns) - optional */
u_short pio_nfctl_min; /* min. PIO cycle time w/o flow ctl - optional */
u_short pio_iordy_min; /* min. PIO c/t with IORDY flow ctl - optional */
short reserved7[2];
u_short rls_ovlap; /* release time (us) for overlap cmd - optional */
u_short rls_service; /* release time (us) for service cmd - optional */
};
/*
* ATAPI operation result structure
*/
struct atapires {
u_char code; /* result code */
#define RES_OK 0 /* i/o done */
#define RES_ERR 1 /* i/o finished with error */
#define RES_NOTRDY 2 /* controller not ready */
#define RES_NODRQ 3 /* no data request */
#define RES_INVDIR 4 /* invalid bus phase direction */
#define RES_OVERRUN 5 /* data overrun */
#define RES_UNDERRUN 6 /* data underrun */
u_char status; /* status register contents */
u_char error; /* error register contents */
};
struct atapidrv { /* delayed attach info */
int ctlr; /* IDE controller, 0/1 */
int unit; /* drive unit, 0/1 */
int port; /* controller base port */
int attached; /* the drive is attached */
};
struct buf;
struct wcd;
typedef void atapi_callback_t(struct wcd *, struct buf *, int, struct atapires);
struct atapicmd { /* ATAPI command block */
struct atapicmd *next; /* next command in queue */
int busy; /* busy flag */
u_char cmd[16]; /* command and args */
int unit; /* drive unit number */
int count; /* byte count, >0 - read, <0 - write */
char *addr; /* data to transfer */
atapi_callback_t *callback; /* call when done */
void *cbarg1; /* callback arg 1 */
void *cbarg2; /* callback arg 1 */
struct atapires result; /* resulting error code */
};
struct atapi { /* ATAPI controller data */
u_short port; /* i/o port base */
u_char ctrlr; /* physical controller number */
u_char debug : 1; /* trace enable flag */
u_char cmd16 : 1; /* 16-byte command flag */
u_char intrcmd : 1; /* interrupt before cmd flag */
u_char slow : 1; /* slow reaction device */
u_char accel : 1; /* accelerated reaction device */
u_char use_dsc : 1; /* use DSC completition handeling */
u_char wait_for_dsc : 1;
u_int dsc_timeout;
u_char attached[2]; /* units are attached to subdrivers */
struct atapi_params *params[2]; /* params for units 0,1 */
struct atapicmd *queue; /* queue of commands to perform */
struct atapicmd *tail; /* tail of queue */
struct atapicmd *free; /* queue of free command blocks */
struct atapicmd cmdrq[16]; /* pool of command requests */
};
#ifdef KERNEL
struct atapi;
extern struct atapidrv atapi_drvtab[4]; /* delayed attach info */
extern int atapi_ndrv; /* the number of potential drives */
extern struct atapi *atapi_tab; /* the table of atapi controllers */
#ifndef ATAPI_STATIC
# define atapi_start (*atapi_start_ptr)
# define atapi_intr (*atapi_intr_ptr)
# define atapi_debug (*atapi_debug_ptr)
# define atapi_request_wait (*atapi_request_wait_ptr)
# define atapi_request_callback (*atapi_request_callback_ptr)
# define atapi_request_immediate (*atapi_request_immediate_ptr)
#endif
#ifndef ATAPI_MODULE
int atapi_attach (int ctlr, int unit, int port);
#endif
/*
* These "functions" are declared with archaic `extern's because they are
* actually pointers in the !ATAPI_STATIC case.
*/
extern int atapi_start (int ctrlr);
extern int atapi_intr (int ctrlr);
extern void atapi_debug (struct atapi *ata, int on);
extern struct atapires atapi_request_wait (struct atapi *ata, int unit,
u_char cmd, u_char a1, u_char a2, u_char a3, u_char a4,
u_char a5, u_char a6, u_char a7, u_char a8, u_char a9,
u_char a10, u_char a11, u_char a12, u_char a13, u_char a14, u_char a15,
char *addr, int count);
extern void atapi_request_callback (struct atapi *ata, int unit,
u_char cmd, u_char a1, u_char a2, u_char a3, u_char a4,
u_char a5, u_char a6, u_char a7, u_char a8, u_char a9,
u_char a10, u_char a11, u_char a12, u_char a13, u_char a14, u_char a15,
char *addr, int count, atapi_callback_t *done, void *x, void *y);
extern struct atapires atapi_request_immediate (struct atapi *ata, int unit,
u_char cmd, u_char a1, u_char a2, u_char a3, u_char a4,
u_char a5, u_char a6, u_char a7, u_char a8, u_char a9,
u_char a10, u_char a11, u_char a12, u_char a13, u_char a14, u_char a15,
char *addr, int count);
#endif