0fc4974f79
- Change the workaround for the autopad/checksum offload bug so that instead of lying about the map size, we actually create a properly padded mbuf and map it as usual. The other trick works, but is ugly. This approach also gives us a chance to zero the pad space to avoid possibly leaking data. - With the PCIe devices, it looks issuing a TX command while there's already a transmission in progress doesn't have any effect. In other words, if you send two packets in rapid succession, the second one may end up sitting in the TX DMA ring until another transmit command is issued later in the future. Basically, if re_txeof() sees that there are still descriptors outstanding, it needs to manually resume the TX DMA channel by issuing another TX command to make sure all transmissions are flushed out. (The PCI devices seem to keep the TX channel moving until all descriptors have been consumed. I'm not sure why the PCIe devices behave differently.) (You can see this issue if you do the following test: plug an re(4) interface into another host via crossover cable, and from the other host do 'ping -c 2 <host with re(4) NIC>' to prime the ARP cache, then do 'ping -c 1 -s 1473 <host with re(4) NIC>'. You're supposed to see two packets sent in response, but you may only see one. If you do 'ping -c 1 -s 1473 <host with re(4) NIC>' again, you'll see two packets, but one will be the missing fragment from the last ping, followed by one of the fragments from this ping.) - Add the PCI ID for the US Robotics 997902 NIC, which is based on the RTL8169S. - Add a tsleep() of 1 second in re_detach() after the interrupt handler is disconnected. This should allow any tasks queued up by the ISR to drain. Now, I know you're supposed to use taskqueue_drain() for this, but something about the way taskqueue_drain() works with taskqueue_fast queues doesn't seem quite right, and I refuse to be tricked into fixing it.
This is the top level of the FreeBSD source directory. This file was last revised on: $FreeBSD$ For copyright information, please see the file COPYRIGHT in this directory (additional copyright information also exists for some sources in this tree - please see the specific source directories for more information). The Makefile in this directory supports a number of targets for building components (or all) of the FreeBSD source tree, the most commonly used one being ``world'', which rebuilds and installs everything in the FreeBSD system from the source tree except the kernel, the kernel-modules and the contents of /etc. The ``world'' target should only be used in cases where the source tree has not changed from the currently running version. See: http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/makeworld.html for more information, including setting make(1) variables. The ``buildkernel'' and ``installkernel'' targets build and install the kernel and the modules (see below). Please see the top of the Makefile in this directory for more information on the standard build targets and compile-time flags. Building a kernel is a somewhat more involved process, documentation for which can be found at: http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/kernelconfig.html And in the config(8) man page. Note: If you want to build and install the kernel with the ``buildkernel'' and ``installkernel'' targets, you might need to build world before. More information is available in the handbook. The sample kernel configuration files reside in the sys/<arch>/conf sub-directory (assuming that you've installed the kernel sources), the file named GENERIC being the one used to build your initial installation kernel. The file NOTES contains entries and documentation for all possible devices, not just those commonly used. It is the successor of the ancient LINT file, but in contrast to LINT, it is not buildable as a kernel but a pure reference and documentation file. Source Roadmap: --------------- bin System/user commands. contrib Packages contributed by 3rd parties. crypto Cryptography stuff (see crypto/README). etc Template files for /etc. games Amusements. gnu Various commands and libraries under the GNU Public License. Please see gnu/COPYING* for more information. include System include files. kerberos5 Kerberos5 (Heimdal) package. lib System libraries. libexec System daemons. release Release building Makefile & associated tools. rescue Build system for statically linked /rescue utilities. sbin System commands. secure Cryptographic libraries and commands. share Shared resources. sys Kernel sources. tools Utilities for regression testing and miscellaneous tasks. usr.bin User commands. usr.sbin System administration commands. For information on synchronizing your source tree with one or more of the FreeBSD Project's development branches, please see: http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/synching.html