front-end and the LSI64854 and NCR53C9x code in case one of these
functions fails. Add detach functions to these parts and make esp(4)
detachable.
- Revert rev. 1.7 of esp_sbus.c, since rev. 1.34 of sbus.c the clockfreq
IVAR defaults to the per-child values.
- Merge ncr53c9x.c rev. 1.111 from NetBSD (partial):
On reset, clear state flags and the msgout queue.
In NetBSD code to notify the upper layer (i.e. CAM in FreeBSD) on reset
was also added with this revision. This is believed to be not necessary
in FreeBSD and was not merged.
This makes ncr53c9x.c to be in sync with NetBSD up to rev. 1.114.
- Conditionalize the LSI64854 support on sbus(4) only instead of sbus(4)
and esp(4) as it's also required for the 'dma', 'espdma' and 'ledma'
busses/devices as well as the 'SUNW,bpp' device (printer port) which
all hang off of sbus(4).
- Add a driver for the 'dma', 'espdma' and 'ledma' (pseudo-)busses/
devices. These busses and devices actually represent the LSI64854 DMA
engines for the ESP SCSI and LANCE Ethernet controllers found on the
SBus of Ultra 1 and SBus add-on cards. With 'espdma' and 'ledma' the
'esp' and 'le' devices hang off of the respective DMA bus instead of
directly from the SBus. The 'dma' devices are either also used in this
manner or on some add-on cards also as a companion device to an 'esp'
device which also hangs off directly from the SBus. With the latter
variant it's a bit tricky to glue the DMA engine to the core logic of
the respective 'esp' device. With rev. 1.35 of sbus.c we are however
guaranteed that such a 'dma' device is probed before the respective
'esp' device which simplifies things a lot. [1]
- In the esp(4) SBus front-end read the part-unique ID code of Fast-SCSI
capable chips the right way. This fixes erroneously detecting some
chips as FAS366 when in fact they are not. Add explicit checks for the
FAS100A, FAS216 and FAS236 variants instead treating all of these as
ESP200. That way we can correctly set the respective Fast-SCSI config
bits instead of driving them out of specs. This includes adding the
FAS100A and FAS236 variants to the NCR53C9x core code. We probably
still subsume some chip variants as ESP200 while in fact they are
another variant which however shouldn't really matter as this will
only happen when these chips are driven at 25MHz or less which implies
not being able to run Fast-SCSI. [3]
- Add a workaround to the NCR53C9x interrupt handler which ignores the
stray interrupt generated by FAS100A when doing path inquiry during
boot and which otherwiese would trigger a panic.
- Add support for the 'esp' devices hanging off of a 'dma' or 'espdma'
busses or which are companions of 'dma' devices to esp(4). In case of
the variants that hang off of a DMA device this is a bit hackish as
esp(4) then directly uses the softc of the respective parent to talk
to the DMA engine. It might make sense to add an interface for this
in order to implement this in a cleaner way however it's not yet clear
how the requirements for the LANCE Ethernet controllers are and the
hack works for now. [2]
This effectively adds support for the onboard SCSI controller in
Ultra 1 as well as most of the ESP-based SBus add-on cards to esp(4).
With this the code for supporting the Performance Technologies SBS430
SBus SCSI add-on cards is also largely in place the remaining bits
were however omitted as it's unclear from the NetBSD how to couple
the DMA engine and the core logic together for these cards.
Obtained from: OpenBSD [1]
Obtained from: NetBSD [2]
Clue from: BSD/OS [3]
Reviewed by: scottl (earlier version)
Tested with: FSBE/S add-on card (FAS236), SSHA add-on card (ESP100A),
Ultra 1 (onboard FAS100A), Ultra 2 (onboard FAS366)
9ea9bafe68