d57ea329f6
The primary focus of these changes is to modernize FreeBSD's
tape infrastructure so that we can take advantage of some of the
features of modern tape drives and allow support for LTFS.
Significant changes and new features include:
o sa(4) driver status and parameter information is now exported via an
XML structure. This will allow for changes and improvements later
on that will not break userland applications. The old MTIOCGET
status ioctl remains, so applications using the existing interface
will not break.
o 'mt status' now reports drive-reported tape position information
as well as the previously available calculated tape position
information. These numbers will be different at times, because
the drive-reported block numbers are relative to BOP (Beginning
of Partition), but the block numbers calculated previously via
sa(4) (and still provided) are relative to the last filemark.
Both numbers are now provided. 'mt status' now also shows the
drive INQUIRY information, serial number and any position flags
(BOP, EOT, etc.) provided with the tape position information.
'mt status -v' adds information on the maximum possible I/O size,
and the underlying values used to calculate it.
o The extra sa(4) /dev entries (/dev/saN.[0-3]) have been removed.
The extra devices were originally added as place holders for
density-specific device nodes. Some OSes (NetBSD, NetApp's OnTap
and Solaris) have had device nodes that, when you write to them,
will automatically select a given density for particular tape drives.
This is a convenient way of switching densities, but it was never
implemented in FreeBSD. Only the device nodes were there, and that
sometimes confused users.
For modern tape devices, the density is generally not selectable
(e.g. with LTO) or defaults to the highest availble density when
the tape is rewritten from BOT (e.g. TS11X0). So, for most users,
density selection won't be necessary. If they do need to select
the density, it is easy enough to use 'mt density' to change it.
o Protection information is now supported. This is either a
Reed-Solomon CRC or CRC32 that is included at the end of each block
read and written. On write, the tape drive verifies the CRC, and
on read, the tape drive provides a CRC for the userland application
to verify.
o New, extensible tape driver parameter get/set interface.
o Density reporting information. For drives that support it,
'mt getdensity' will show detailed information on what formats the
tape drive supports, and what formats the tape drive supports.
o Some mt(1) functionality moved into a new mt(3) library so that
external applications can reuse the code.
o The new mt(3) library includes helper routines to aid in parsing
the XML output of the sa(4) driver, and build a tree of driver
metadata.
o Support for the MTLOAD (load a tape in the drive) and MTWEOFI
(write filemark immediate) ioctls needed by IBM's LTFS
implementation.
o Improve device departure behavior for the sa(4) driver. The previous
implementation led to hangs when the device was open.
o This has been tested on the following types of drives:
IBM TS1150
IBM TS1140
IBM LTO-6
IBM LTO-5
HP LTO-2
Seagate DDS-4
Quantum DLT-4000
Exabyte 8505
Sony DDS-2
contrib/groff/tmac/doc-syms,
share/mk/bsd.libnames.mk,
lib/Makefile,
Add libmt.
lib/libmt/Makefile,
lib/libmt/mt.3,
lib/libmt/mtlib.c,
lib/libmt/mtlib.h,
New mt(3) library that contains functions moved from mt(1) and
new functions needed to interact with the updated sa(4) driver.
This includes XML parser helper functions that application writers
can use when writing code to query tape parameters.
rescue/rescue/Makefile:
Add -lmt to CRUNCH_LIBS.
src/share/man/man4/mtio.4
Clarify this man page a bit, and since it contains what is
essentially the mtio.h header file, add new ioctls and structure
definitions from mtio.h.
src/share/man/man4/sa.4
Update BUGS and maintainer section.
sys/cam/scsi/scsi_all.c,
sys/cam/scsi/scsi_all.h:
Add SCSI SECURITY PROTOCOL IN/OUT CDB definitions and CDB building
functions.
sys/cam/scsi/scsi_sa.c
sys/cam/scsi/scsi_sa.h
Many tape driver changes, largely outlined above.
Increase the sa(4) driver read/write timeout from 4 to 32
minutes. This is based on the recommended values for IBM LTO
5/6 drives. This may also avoid timeouts for other tape
hardware that can take a long time to do retries and error
recovery. Longer term, a better way to handle this is to ask
the drive for recommended timeout values using the REPORT
SUPPORTED OPCODES command. Modern IBM and Oracle tape drives
at least support that command, and it would allow for more
accurate timeout values.
Add XML status generation. This is done with a series of
macros to eliminate as much duplicate code as possible. The
new XML-based status values are reported through the new
MTIOCEXTGET ioctl.
Add XML driver parameter reporting, using the new MTIOCPARAMGET
ioctl.
Add a new driver parameter setting interface, using the new
MTIOCPARAMSET and MTIOCSETLIST ioctls.
Add a new MTIOCRBLIM ioctl to get block limits information.
Add CCB/CDB building routines scsi_locate_16, scsi_locate_10,
and scsi_read_position_10().
scsi_locate_10 implements the LOCATE command, as does the
existing scsi_set_position() command. It just supports
additional arguments and features. If/when we figure out a
good way to provide backward compatibility for older
applications using the old function API, we can just revamp
scsi_set_position(). The same goes for
scsi_read_position_10() and the existing scsi_read_position()
function.
Revamp sasetpos() to take the new mtlocate structure as an
argument. It now will use either scsi_locate_10() or
scsi_locate_16(), depending upon the arguments the user
supplies. As before, once we change position we don't have a
clear idea of what the current logical position of the tape
drive is.
For tape drives that support long form position data, we
read the current position and store that for later reporting
after changing the position. This should help applications
like Bacula speed tape access under FreeBSD once they are
modified to support the new ioctls.
Add a new quirk, SA_QUIRK_NO_LONG_POS, that is set for all
drives that report SCSI-2 or older, as well as drives that
report an Illegal Request type error for READ POSITION with
the long format. So we should automatically detect drives
that don't support the long form and stop asking for it after
an initial try.
Add a partition number to the sa(4) softc.
Improve device departure handling. The previous implementation
led to hangs when the device was open.
If an application had the sa(4) driver open, and attempted to
close it after it went away, the cam_periph_release() call in
saclose() would cause the periph to get destroyed because that
was the last reference to it. Because destroy_dev() was
called from the sa(4) driver's cleanup routine (sacleanup()),
and would block waiting for the close to happen, a deadlock
would result.
So instead of calling destroy_dev() from the cleanup routine,
call destroy_dev_sched_cb() from saoninvalidate() and wait for
the callback.
Acquire a reference for devfs in saregister(), and release it
in the new sadevgonecb() routine when all devfs devices for
the particular sa(4) driver instance are gone.
Add a new function, sasetupdev(), to centralize setting
per-instance devfs device parameters instead of repeating the
code in saregister().
Add an open count to the softc, so we know how many
peripheral driver references are a result of open
sessions.
Add the D_TRACKCLOSE flag to the cdevsw flags so
that we get a 1:1 mapping of open to close calls
instead of a N:1 mapping.
This should be a no-op for everything except the
control device, since we don't allow more than one
open on non-control devices.
However, since we do allow multiple opens on the
control device, the combination of the open count
and the D_TRACKCLOSE flag should result in an
accurate peripheral driver reference count, and an
accurate open count.
The accurate open count allows us to release all
peripheral driver references that are the result
of open contexts once we get the callback from devfs.
sys/sys/mtio.h:
Add a number of new mt(4) ioctls and the requisite data
structures. None of the existing interfaces been removed
or changed.
This includes definitions for the following new ioctls:
MTIOCRBLIM /* get block limits */
MTIOCEXTLOCATE /* seek to position */
MTIOCEXTGET /* get tape status */
MTIOCPARAMGET /* get tape params */
MTIOCPARAMSET /* set tape params */
MTIOCSETLIST /* set N params */
usr.bin/mt/Makefile:
mt(1) now depends on libmt, libsbuf and libbsdxml.
usr.bin/mt/mt.1:
Document new mt(1) features and subcommands.
usr.bin/mt/mt.c:
Implement support for mt(1) subcommands that need to
use getopt(3) for their arguments.
Implement a new 'mt status' command to replace the old
'mt status' command. The old status command has been
renamed 'ostatus'.
The new status function uses the MTIOCEXTGET ioctl, and
therefore parses the XML data to determine drive status.
The -x argument to 'mt status' allows the user to dump out
the raw XML reported by the kernel.
The new status display is mostly the same as the old status
display, except that it doesn't print the redundant density
mode information, and it does print the current partition
number and position flags.
Add a new command, 'mt locate', that will supersede the
old 'mt setspos' and 'mt sethpos' commands. 'mt locate'
implements all of the functionality of the MTIOCEXTLOCATE
ioctl, and allows the user to change the logical position
of the tape drive in a number of ways. (Partition,
block number, file number, set mark number, end of data.)
The immediate bit and the explicit address bits are
implemented, but not documented in the man page.
Add a new 'mt weofi' command to use the new MTWEOFI ioctl.
This allows the user to ask the drive to write a filemark
without waiting around for the operation to complete.
Add a new 'mt getdensity' command that gets the XML-based
tape drive density report from the sa(4) driver and displays
it. This uses the SCSI REPORT DENSITY SUPPORT command
to get comprehensive information from the tape drive about
what formats it is able to read and write.
Add a new 'mt protect' command that allows getting and setting
tape drive protection information. The protection information
is a CRC tacked on to the end of every read/write from and to
the tape drive.
Sponsored by: Spectra Logic
MFC after: 1 month
|
||
|---|---|---|
| .. | ||
| contrib | ||
| doc | ||
| font | ||
| man | ||
| src | ||
| tmac | ||
| aclocal.m4 | ||
| BUG-REPORT | ||
| ChangeLog | ||
| ChangeLog.115 | ||
| ChangeLog.116 | ||
| ChangeLog.117 | ||
| ChangeLog.118 | ||
| configure | ||
| configure.ac | ||
| COPYING | ||
| FDL | ||
| FREEBSD-upgrade | ||
| FREEBSD-Xlist | ||
| gendef.sh | ||
| INSTALL | ||
| install-sh | ||
| INSTALL.gen | ||
| LICENSE | ||
| Makefile | ||
| Makefile.ccpg | ||
| Makefile.comm | ||
| Makefile.cpg | ||
| Makefile.dev | ||
| Makefile.in | ||
| Makefile.init | ||
| Makefile.lib | ||
| Makefile.man | ||
| Makefile.sub | ||
| MANIFEST | ||
| mdate.sh | ||
| mkinstalldirs | ||
| MORE.STUFF | ||
| NEWS | ||
| PROBLEMS | ||
| PROJECTS | ||
| README | ||
| README.MinGW | ||
| REVISION | ||
| stamp-h.in | ||
| test-groff.in | ||
| TODO | ||
| VERSION | ||
This is the GNU `groff' document formatting system. The version
number is given in the file VERSION.
Included in this release are implementations of `troff', `pic', `eqn',
`tbl', `grn', `refer', `-man', `-mdoc', `-mom', and `-ms' macros, and
drivers for `PostScript', `TeX dvi' format, `HP LaserJet 4' printers,
`Canon CAPSL' printers, `HTML' format (beta status), and
typewriter-like devices. Also included is a modified version of the
Berkeley `-me' macros, the enhanced version `gxditview' of the X11
`xditview' previewer, and an implementation of the `-mm' macros
contributed by Joergen Haegg (jh@axis.se).
See the file `INSTALL' for installation instructions. You will
require a C++ compiler.
The file `NEWS' describes recent user-visible changes to `groff'.
`groff' is free software. See the file `COPYING' for copying
permission.
The file `PROBLEMS' describes various problems that have been
encountered in compiling, installing, and running `groff'.
The most recent released version of `groff' is always available by
anonymous ftp from `ftp.gnu.org' in the directory `gnu/groff'.
The current development version of `groff' is available from a `CVS'
repository. You can access it by first selecting a parent directory
in which to create a working copy (call it, say, `~/cvswork'), and
then executing the commands
cd ~/cvswork
CVS_RSH=ssh; export CVS_RSH
cvs -d:ext:anoncvs@savannah.gnu.org/cvsroot/groff -z5 co groff
(Note that you need an `ssh' client for security reasons.)
This will create a subdirectory, `~/cvswork/groff', with a "checked
out" copy of the `CVS' repository. An update of this working copy may
be achieved, at any later time by invoking the commands
cd ~/cvswork/groff
CVS_RSH=ssh cvs -z5 update -dP
Please read the `CVS' info pages for further details.
Finally, it is possible to access the `CVS' with a web browser by
pointing it to
http://savannah.gnu.org/cvs/?group=groff
Alternatively, you can download snapshots (which are updated twice a day).
The complete `groff' source as a single file is available at
http://groff.ffii.org/groff/devel/groff-current.tar.gz
A diff file relative to `groff-<version>', the latest official `groff'
release is available at
http://groff.ffii.org/groff/devel/groff-<version>-current.diff.gz
Assuming that `groff-<version>.tar.gz' and
`groff-<version>-current.diff.gz' are in the same directory, do the
following to apply the diff file:
tar xzvf groff-<version>.tar.gz
cd groff-<version>
gunzip -c ../groff-<version>-current.diff.gz | patch -p1
Depending on your requirements, you may need at least some of the
following tools to build `groff' directly from its source:
ghostscript
the psutils package
the netpbm package
texinfo 4.8
bison >= 1.875b or byacc
Note that `texinfo' and `bison' or `byacc' are required only for
building from `CVS' sources (either a checked out working copy, or a
daily snapshot). They are not required for building from a stable
release tarball. Also note that the version numbers stated are the
minimum supported. No version of `texinfo' < 4.8 will work, and the
original release of `bison' 1.875 is known not to work; you *may* find
that `bison' releases < 1.875 will work, but in case of difficulty,
please update to a later version *before* posting a bug report.
For *all* sources, you need ghostscript for creation of either `PDF' or
`HTML' output; the `netpbm' and `psutils' packages are required only for
`HTML' output. If you don't intend to produce output in either of these
formats, then these packages are unnecessary.
In Linux Debian, the installation of `texinfo' is dangerous. For it
creates a file `install-info' that will block the system installation.
So the created `/usr/local/bin/install-info' must be renamed.
The `groff' configure script searches for the X11 headers and
libraries `Xaw' and `Xmu'. So the corresponding developer packages of
your system must be installed, otherwise `groff' does not install
`gxditview' and the `-TX*' devices. In Debian, the developer packages
are `libxaw7-dev' and `libxmu-dev'.
Please report bugs using the form in the file `BUG-REPORT'; the idea of
this is to make sure that FSF has all the information it needs to fix
the bug. At the very least, read the `BUG-REPORT' form and make sure
that you supply all the information that it asks for. Even if you are
not sure that something is a bug, report it using `BUG-REPORT': this will
enable us to determine whether it really is a bug or not.
Three mailing lists are available:
bug-groff@gnu.org for reporting bugs
groff@gnu.org for general discussion of groff
groff-commit@gnu.org a read-only list showing commitments
to the CVS repository
You can post mails directly to the `bug-groff' list, without subscribing;
to post mails to the `groff' list you must subscribe to it.
To subscribe, send a mail to <list>-request@<domain> (example:
groff-request@gnu.org for the `groff' list) with the word `subscribe'
in either the subject or body of the email (don't include the quotes).
Alternatively, you may subscribe by visiting the web pages at
http://lists.gnu.org/mailman/listinfo/bug-groff
http://lists.gnu.org/mailman/listinfo/groff
http://lists.gnu.org/mailman/listinfo/groff-commit
Each of these web pages also provides a link to a browseable archive of
postings to the corresponding mailing list.
GNU `groff' was written by James Clark <jjc@jclark.com>. It is now
maintained by Ted Harding <ted.harding@nessie.mcc.ac.uk> and Werner
Lemberg <wl@gnu.org>.