13459a7344
When restarting the sequencer, ensure that the SCBCNT register is 0. A non-zero count will prevent the setting of the CCSCBDIR bit in any future dma operations. The only time CCSCBCNT would be non-zero is if we happened to halt the dma during a reset, but even that should never happen. Better safe than sorry. When a command completes before the target responds to an ATN for a recovery command, we now notify the kernel so that any recovery operation requeued in the qinfifo can be removed safely. In the past, we did this in ahc_done(), but ahc_done() may be called without the card paused. This also avoids a recursive call to ahc_search_qinifo() which could have occurred if ahc_search_qinififo() happened to be the routine to complete a recovery action. Fix 8bit math used for adjusting the qinfifo. The index must be wrapped properly within the 256 entry array. We rely on the fact that qinfifonext is a uint8_t in most cases to handle this wrap, but we missed a few spots where the resultant calculation was promoted to an int. Change the way that we deal with aborting the first or second entry from the qinfifo. We now swap the first entry in the qinfifo with the "next queued scb" to force the sequencer to see an abort collision if we ever touch the qinififo while the sequencer is mid SCB dma. aic7xxx.reg: Add new MKMSG_FAILED sequencer interrupt. This displaced the BOGUS_TAG interrupt used in some previous sequencer code debugging. aic7xxx.seq: Increment our position in the qinfifo only once the dma is complete and we have verified that the queue has not been changed during our DMA. This simplifies code in the kernel. Protect against "instruction creep" when issuing a pausing sequencer interrupt. On at least the 7890/91/96/97, the sequencer will coast after issuing the interrupt for up to two instructions. In the past we delt with this by using carefully placed nops. Now we call a routine to issue the interrupt followed by a nop and a ret. Tell the kernel should an SCB complete with the MK_MESSAGE flag still set. This means the target ignored our ATN request. Clear the channel twice as we exit the data phase. On the aic7890/91, the S/G preload logic may require the second clearing to get the last S/G out of the FIFO. aic7xxx_freebsd.c: Don't bother searching the qinfifo for a doubly queued recovery scb in ahc_done. This case is handled by the core driver now. Free the path used to issue async callbacks after the callback is complete. aic7xxx_inline.h: Split the SCB queue routine into a routine that swaps the SCB with the "next queued SCB" and a routine that calls the swapping routine and notifies the card of the new SCB. The swapping routine is now also used by ahc_search_qinfifo.
This is the top level of the FreeBSD source directory. This file was last revised on: $FreeBSD$ For copyright information, please see the file COPYRIGHT in this directory (additional copyright information also exists for some sources in this tree - please see the specific source directories for more information). The Makefile in this directory supports a number of targets for building components (or all) of the FreeBSD source tree, the most commonly used one being ``world'', which rebuilds and installs everything in the FreeBSD system from the source tree except the kernel, the kernel-modules and the contents of /etc. The ``buildkernel'' and ``installkernel'' targets build and install the kernel and the modules (see below). Please see the top of the Makefile in this directory for more information on the standard build targets and compile-time flags. Building a kernel is a somewhat more involved process, documentation for which can be found at: http://www.freebsd.org/handbook/kernelconfig.html And in the config(8) man page. Note: If you want to build and install the kernel with the ``buildkernel'' and ``installkernel'' targets, you have to build world before. More information is available in the handbook. The sample kernel configuration files reside in the sys/i386/conf sub-directory (assuming that you've installed the kernel sources), the file named GENERIC being the one used to build your initial installation kernel. The file NOTES contains entries and documentation for all possible devices, not just those commonly used. It is the successor of the ancient LINT file, but in contrast to LINT, it is not buildable as a kernel but a pure reference and documentation file. Source Roadmap: --------------- bin System/User commands. contrib Packages contributed by 3rd parties. crypto Cryptography stuff (see crypto/README). etc Template files for /etc games Amusements. gnu Various commands and libraries under the GNU Public License. Please see gnu/COPYING* for more information. include System include files. kerberosIV Kerberos package. lib System libraries. libexec System daemons. release Release building Makefile & associated tools. sbin System commands. secure Cryptographic libraries and commands. share Shared resources. sys Kernel sources. tools Utilities for regression testing and miscellaneous tasks. usr.bin User commands. usr.sbin System administration commands. For information on synchronizing your source tree with one or more of the FreeBSD Project's development branches, please see: http://www.freebsd.org/handbook/synching.html