in 4 byte chunks. It turns out that with the 82c169C on the Netgear
FA-310TX Rev D2, if you tell the chip you have reserved a buffer of 1518
bytes, it will actually treat it as 1516 bytes since 1518 is divisible
by four. Consequently, a packet of 1514 bytes will always end up consuming
two buffers: the last coupleof bytes will spill over into the next
descriptor. This causes the pn_rx_bug_war() routine to trip unnecessarily.
I'm not sure if the 82c169B or 82c168 chips behave the same way; I'll
have to check them. In any case, this change should work just as well
with them. Note that the FA-310TX Rev D2 also has a Broadcom PHY
instead of a Level One LXT970 PHY, however this shouldn't make any
difference as far as the driver is concerned.
This change also allows me to do a way with one rounding overation in
pn_rx-buf_war().
-------------------------------------------------------------------------------
Recent versions of 3.0-current have the bktr driver built in. Older versions
of 3.0 and all versions of 2.2 need to have the driver files installed by hand:
cp ioctl_bt848.h /sys/i386/include/
cp brktree_reg.h brooktree848.c /sys/pci/
In /sys/conf/files add:
pci/brooktree848.c optional bktr device-driver
-------------------------------------------------------------------------------
In all cases you will need to add the driver to your kernel:
In your kernel configuration file:
controller pci0 #if you already have this line don't add it.
device bktr0
There is no need to specify DMA channels nor interrupts for this
driver.
-------------------------------------------------------------------------------
Finally you need to create nodes for the driver:
Create a video device:
mknod /dev/bktr0 c 92 0
Create a tuner device:
mknod /dev/tuner0 c 92 16
-------------------------------------------------------------------------------
The code attempts to auto-probe code to detect card/tuner types.
The detected card is printed in the dmesg as the driver is loaded. If
this fails to detect the proper card you can override it in brooktree848.c:
#define OVERRIDE_CARD <card type>
where <card type> is one of:
CARD_UNKNOWN
CARD_MIRO
CARD_HAUPPAUGE
CARD_STB
CARD_INTEL
-------------------------------------------------------------------------------
This model now separates the "tuner control" items into a minor device:
minor device layout: xxxxxxxx xxxT UUUU
UUUU: the card (ie UNIT) identifier, 0 thru 15
T == 0: video device
T == 1: tuner device
Access your tuner ioctl thru your tuner device handle and anything
which controls the video capture process thru the video device handle.
Certain ioctl()s such as video source are available thru both devices.
-------------------------------------------------------------------------------
If your tuner does not work properly or is not recognized properly
try setting the tuner type via or card type:
sysctl -w hw.bt848.card=<integer> current valid values are 0 to 5 inclusive
sysctl -w hw.bt848.tuner=<integer> where integer is a value from 1 to 10
systcl -w hw.bt848.reverse_mute=<1 | 0> to reverse the mute function in the
driver set variable to 1.
The exact format of the sysctl bt848 variable is:
unit << 8 | value
unit identifies the pci bt848 board to be affected 0 is the first bt848
board, 1 is the second bt848 board.
value denotes the integer value for tuners is a value from 0 to 10 for
reversing the mute function of the tuner the value is 1 or 0.
to find out all the bt848 variables:
sysctl hw.bt848
-------------------------------------------------------------------------------
The bt848 driver consists of:
src/sys/i386/include/ioctl_bt848.h
src/sys/pci/brktree_reg.h
src/sys/pci/brooktree848.c
19a3e3add0