21c85d9d3b
- Put "_LE_" into the register access macros to indicate little endian byte order is expected by the hardware. - Avoid using the bounce buffer when not strictly needed. Try to move data directly using bus-space functions first. - Ensure we preserve the reserved bits in the power down mode register. Else the hardware goes into a non-recoverable state. - Always use 32-bit access when writing or reading registers or FIFOs, because the hardware is 32-bit oriented and don't really understand 8- and 16-bit access. - Correct writes to the memory address register. There is no need to shift the register offset. - Correct interval for interrupt endpoints. - Optimise 90ns internal memory buffer read delay. - Rename PDT into PTD, which is how the datasheet writes it. - Add missing programming for activating host controller PTDs. Sponsored by: DARPA, AFRL
3118 lines
74 KiB
C
3118 lines
74 KiB
C
/* $FreeBSD$ */
|
|
/*-
|
|
* Copyright (c) 2014 Hans Petter Selasky <hselasky@FreeBSD.org>
|
|
* All rights reserved.
|
|
*
|
|
* This software was developed by SRI International and the University of
|
|
* Cambridge Computer Laboratory under DARPA/AFRL contract (FA8750-10-C-0237)
|
|
* ("CTSRD"), as part of the DARPA CRASH research programme.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
* documentation and/or other materials provided with the distribution.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
|
|
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
|
|
* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
|
|
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
|
|
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
|
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
|
|
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
|
|
* SUCH DAMAGE.
|
|
*/
|
|
|
|
/*
|
|
* This file contains the driver for the SAF1761 series USB OTG
|
|
* controller.
|
|
*
|
|
* Datasheet is available from:
|
|
* http://www.nxp.com/products/automotive/multimedia/usb/SAF1761BE.html
|
|
*/
|
|
|
|
#ifdef USB_GLOBAL_INCLUDE_FILE
|
|
#include USB_GLOBAL_INCLUDE_FILE
|
|
#else
|
|
#include <sys/stdint.h>
|
|
#include <sys/stddef.h>
|
|
#include <sys/param.h>
|
|
#include <sys/queue.h>
|
|
#include <sys/types.h>
|
|
#include <sys/systm.h>
|
|
#include <sys/kernel.h>
|
|
#include <sys/bus.h>
|
|
#include <sys/module.h>
|
|
#include <sys/lock.h>
|
|
#include <sys/mutex.h>
|
|
#include <sys/condvar.h>
|
|
#include <sys/sysctl.h>
|
|
#include <sys/sx.h>
|
|
#include <sys/unistd.h>
|
|
#include <sys/callout.h>
|
|
#include <sys/malloc.h>
|
|
#include <sys/priv.h>
|
|
|
|
#include <dev/usb/usb.h>
|
|
#include <dev/usb/usbdi.h>
|
|
|
|
#define USB_DEBUG_VAR saf1761_otg_debug
|
|
|
|
#include <dev/usb/usb_core.h>
|
|
#include <dev/usb/usb_debug.h>
|
|
#include <dev/usb/usb_busdma.h>
|
|
#include <dev/usb/usb_process.h>
|
|
#include <dev/usb/usb_transfer.h>
|
|
#include <dev/usb/usb_device.h>
|
|
#include <dev/usb/usb_hub.h>
|
|
#include <dev/usb/usb_util.h>
|
|
|
|
#include <dev/usb/usb_controller.h>
|
|
#include <dev/usb/usb_bus.h>
|
|
#endif /* USB_GLOBAL_INCLUDE_FILE */
|
|
|
|
#include <dev/usb/controller/saf1761_otg.h>
|
|
#include <dev/usb/controller/saf1761_otg_reg.h>
|
|
|
|
#define SAF1761_OTG_BUS2SC(bus) \
|
|
((struct saf1761_otg_softc *)(((uint8_t *)(bus)) - \
|
|
((uint8_t *)&(((struct saf1761_otg_softc *)0)->sc_bus))))
|
|
|
|
#ifdef USB_DEBUG
|
|
static int saf1761_otg_debug = 0;
|
|
static int saf1761_otg_forcefs = 0;
|
|
|
|
static
|
|
SYSCTL_NODE(_hw_usb, OID_AUTO, saf1761_otg, CTLFLAG_RW, 0,
|
|
"USB SAF1761 DCI");
|
|
|
|
SYSCTL_INT(_hw_usb_saf1761_otg, OID_AUTO, debug, CTLFLAG_RW,
|
|
&saf1761_otg_debug, 0, "SAF1761 DCI debug level");
|
|
SYSCTL_INT(_hw_usb_saf1761_otg, OID_AUTO, forcefs, CTLFLAG_RW,
|
|
&saf1761_otg_forcefs, 0, "SAF1761 DCI force FULL speed");
|
|
#endif
|
|
|
|
#define SAF1761_OTG_INTR_ENDPT 1
|
|
|
|
/* prototypes */
|
|
|
|
static const struct usb_bus_methods saf1761_otg_bus_methods;
|
|
static const struct usb_pipe_methods saf1761_otg_non_isoc_methods;
|
|
static const struct usb_pipe_methods saf1761_otg_device_isoc_methods;
|
|
|
|
static saf1761_otg_cmd_t saf1761_host_setup_tx;
|
|
static saf1761_otg_cmd_t saf1761_host_bulk_data_rx;
|
|
static saf1761_otg_cmd_t saf1761_host_bulk_data_tx;
|
|
static saf1761_otg_cmd_t saf1761_host_intr_data_rx;
|
|
static saf1761_otg_cmd_t saf1761_host_intr_data_tx;
|
|
static saf1761_otg_cmd_t saf1761_host_isoc_data_rx;
|
|
static saf1761_otg_cmd_t saf1761_host_isoc_data_tx;
|
|
static saf1761_otg_cmd_t saf1761_device_setup_rx;
|
|
static saf1761_otg_cmd_t saf1761_device_data_rx;
|
|
static saf1761_otg_cmd_t saf1761_device_data_tx;
|
|
static saf1761_otg_cmd_t saf1761_device_data_tx_sync;
|
|
static void saf1761_otg_device_done(struct usb_xfer *, usb_error_t);
|
|
static void saf1761_otg_do_poll(struct usb_bus *);
|
|
static void saf1761_otg_standard_done(struct usb_xfer *);
|
|
static void saf1761_otg_intr_set(struct usb_xfer *, uint8_t);
|
|
static void saf1761_otg_root_intr(struct saf1761_otg_softc *);
|
|
|
|
/*
|
|
* Here is a list of what the SAF1761 chip can support. The main
|
|
* limitation is that the sum of the buffer sizes must be less than
|
|
* 8192 bytes.
|
|
*/
|
|
static const struct usb_hw_ep_profile saf1761_otg_ep_profile[] = {
|
|
|
|
[0] = {
|
|
.max_in_frame_size = 64,
|
|
.max_out_frame_size = 64,
|
|
.is_simplex = 0,
|
|
.support_control = 1,
|
|
},
|
|
[1] = {
|
|
.max_in_frame_size = SOTG_HS_MAX_PACKET_SIZE,
|
|
.max_out_frame_size = SOTG_HS_MAX_PACKET_SIZE,
|
|
.is_simplex = 0,
|
|
.support_interrupt = 1,
|
|
.support_bulk = 1,
|
|
.support_isochronous = 1,
|
|
.support_in = 1,
|
|
.support_out = 1,
|
|
},
|
|
};
|
|
|
|
static void
|
|
saf1761_otg_get_hw_ep_profile(struct usb_device *udev,
|
|
const struct usb_hw_ep_profile **ppf, uint8_t ep_addr)
|
|
{
|
|
if (ep_addr == 0) {
|
|
*ppf = saf1761_otg_ep_profile + 0;
|
|
} else if (ep_addr < 8) {
|
|
*ppf = saf1761_otg_ep_profile + 1;
|
|
} else {
|
|
*ppf = NULL;
|
|
}
|
|
}
|
|
|
|
static void
|
|
saf1761_otg_pull_up(struct saf1761_otg_softc *sc)
|
|
{
|
|
/* activate pullup on D+, if possible */
|
|
|
|
if (!sc->sc_flags.d_pulled_up && sc->sc_flags.port_powered) {
|
|
DPRINTF("\n");
|
|
|
|
sc->sc_flags.d_pulled_up = 1;
|
|
}
|
|
}
|
|
|
|
static void
|
|
saf1761_otg_pull_down(struct saf1761_otg_softc *sc)
|
|
{
|
|
/* release pullup on D+, if possible */
|
|
|
|
if (sc->sc_flags.d_pulled_up) {
|
|
DPRINTF("\n");
|
|
|
|
sc->sc_flags.d_pulled_up = 0;
|
|
}
|
|
}
|
|
|
|
static void
|
|
saf1761_otg_wakeup_peer(struct saf1761_otg_softc *sc)
|
|
{
|
|
uint16_t temp;
|
|
|
|
if (!(sc->sc_flags.status_suspend))
|
|
return;
|
|
|
|
DPRINTFN(5, "\n");
|
|
|
|
temp = SAF1761_READ_LE_4(sc, SOTG_MODE);
|
|
SAF1761_WRITE_LE_4(sc, SOTG_MODE, temp | SOTG_MODE_SNDRSU);
|
|
SAF1761_WRITE_LE_4(sc, SOTG_MODE, temp & ~SOTG_MODE_SNDRSU);
|
|
|
|
/* Wait 8ms for remote wakeup to complete. */
|
|
usb_pause_mtx(&sc->sc_bus.bus_mtx, hz / 125);
|
|
|
|
}
|
|
|
|
static uint8_t
|
|
saf1761_host_channel_alloc(struct saf1761_otg_softc *sc, struct saf1761_otg_td *td)
|
|
{
|
|
uint32_t x;
|
|
|
|
if (td->channel < SOTG_HOST_CHANNEL_MAX)
|
|
return (0);
|
|
|
|
switch (td->ep_type) {
|
|
case UE_INTERRUPT:
|
|
for (x = 0; x != 32; x++) {
|
|
if (sc->sc_host_intr_map & (1 << x))
|
|
continue;
|
|
sc->sc_host_intr_map |= (1 << x);
|
|
td->channel = 32 + x;
|
|
return (0);
|
|
}
|
|
break;
|
|
case UE_ISOCHRONOUS:
|
|
for (x = 0; x != 32; x++) {
|
|
if (sc->sc_host_isoc_map & (1 << x))
|
|
continue;
|
|
sc->sc_host_isoc_map |= (1 << x);
|
|
td->channel = x;
|
|
return (0);
|
|
}
|
|
break;
|
|
default:
|
|
for (x = 0; x != 32; x++) {
|
|
if (sc->sc_host_async_map & (1 << x))
|
|
continue;
|
|
sc->sc_host_async_map |= (1 << x);
|
|
td->channel = 64 + x;
|
|
return (0);
|
|
}
|
|
break;
|
|
}
|
|
return (1);
|
|
}
|
|
|
|
static void
|
|
saf1761_host_channel_free(struct saf1761_otg_softc *sc, struct saf1761_otg_td *td)
|
|
{
|
|
uint32_t x;
|
|
|
|
if (td->channel >= SOTG_HOST_CHANNEL_MAX)
|
|
return;
|
|
|
|
/* disable channel */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_PTD(td->channel) + SOTG_PTD_DW3, 0);
|
|
SAF1761_WRITE_LE_4(sc, SOTG_PTD(td->channel) + SOTG_PTD_DW0, 0);
|
|
|
|
switch (td->ep_type) {
|
|
case UE_INTERRUPT:
|
|
x = td->channel - 32;
|
|
sc->sc_host_intr_map &= ~(1 << x);
|
|
td->channel = SOTG_HOST_CHANNEL_MAX;
|
|
break;
|
|
case UE_ISOCHRONOUS:
|
|
x = td->channel;
|
|
sc->sc_host_isoc_map &= ~(1 << x);
|
|
td->channel = SOTG_HOST_CHANNEL_MAX;
|
|
break;
|
|
default:
|
|
x = td->channel - 64;
|
|
sc->sc_host_async_map &= ~(1 << x);
|
|
td->channel = SOTG_HOST_CHANNEL_MAX;
|
|
break;
|
|
}
|
|
}
|
|
|
|
static uint32_t
|
|
saf1761_peek_host_memory_le_4(struct saf1761_otg_softc *sc, uint32_t offset)
|
|
{
|
|
SAF1761_WRITE_LE_4(sc, SOTG_MEMORY_REG, offset);
|
|
SAF1761_90NS_DELAY(sc); /* read prefetch time is 90ns */
|
|
return (SAF1761_READ_LE_4(sc, offset));
|
|
}
|
|
|
|
static void
|
|
saf1761_read_host_memory(struct saf1761_otg_softc *sc,
|
|
struct saf1761_otg_td *td, uint32_t len)
|
|
{
|
|
struct usb_page_search buf_res;
|
|
uint32_t offset;
|
|
uint32_t count;
|
|
|
|
if (len == 0)
|
|
return;
|
|
|
|
offset = SOTG_DATA_ADDR(td->channel);
|
|
SAF1761_WRITE_LE_4(sc, SOTG_MEMORY_REG, offset);
|
|
SAF1761_90NS_DELAY(sc); /* read prefetch time is 90ns */
|
|
|
|
/* optimised read first */
|
|
while (len > 0) {
|
|
usbd_get_page(td->pc, td->offset, &buf_res);
|
|
|
|
/* get correct length */
|
|
if (buf_res.length > len)
|
|
buf_res.length = len;
|
|
|
|
/* check buffer alignment */
|
|
if (((uintptr_t)buf_res.buffer) & 3)
|
|
break;
|
|
|
|
count = buf_res.length & ~3;
|
|
if (count == 0)
|
|
break;
|
|
|
|
bus_space_read_region_4((sc)->sc_io_tag, (sc)->sc_io_hdl,
|
|
offset, buf_res.buffer, count / 4);
|
|
|
|
len -= count;
|
|
offset += count;
|
|
|
|
/* update remainder and offset */
|
|
td->remainder -= count;
|
|
td->offset += count;
|
|
}
|
|
|
|
if (len > 0) {
|
|
/* use bounce buffer */
|
|
bus_space_read_region_4((sc)->sc_io_tag, (sc)->sc_io_hdl,
|
|
offset, sc->sc_bounce_buffer, (len + 3) / 4);
|
|
usbd_copy_in(td->pc, td->offset,
|
|
sc->sc_bounce_buffer, len);
|
|
|
|
/* update remainder and offset */
|
|
td->remainder -= len;
|
|
td->offset += len;
|
|
}
|
|
}
|
|
|
|
static void
|
|
saf1761_write_host_memory(struct saf1761_otg_softc *sc,
|
|
struct saf1761_otg_td *td, uint32_t len)
|
|
{
|
|
struct usb_page_search buf_res;
|
|
uint32_t offset;
|
|
uint32_t count;
|
|
|
|
if (len == 0)
|
|
return;
|
|
|
|
offset = SOTG_DATA_ADDR(td->channel);
|
|
|
|
/* optimised write first */
|
|
while (len > 0) {
|
|
usbd_get_page(td->pc, td->offset, &buf_res);
|
|
|
|
/* get correct length */
|
|
if (buf_res.length > len)
|
|
buf_res.length = len;
|
|
|
|
/* check buffer alignment */
|
|
if (((uintptr_t)buf_res.buffer) & 3)
|
|
break;
|
|
|
|
count = buf_res.length & ~3;
|
|
if (count == 0)
|
|
break;
|
|
|
|
bus_space_write_region_4((sc)->sc_io_tag, (sc)->sc_io_hdl,
|
|
offset, buf_res.buffer, count / 4);
|
|
|
|
len -= count;
|
|
offset += count;
|
|
|
|
/* update remainder and offset */
|
|
td->remainder -= count;
|
|
td->offset += count;
|
|
}
|
|
if (len > 0) {
|
|
/* use bounce buffer */
|
|
usbd_copy_out(td->pc, td->offset, sc->sc_bounce_buffer, len);
|
|
bus_space_write_region_4((sc)->sc_io_tag, (sc)->sc_io_hdl,
|
|
offset, sc->sc_bounce_buffer, (len + 3) / 4);
|
|
|
|
/* update remainder and offset */
|
|
td->remainder -= len;
|
|
td->offset += len;
|
|
}
|
|
}
|
|
|
|
static uint8_t
|
|
saf1761_host_setup_tx(struct saf1761_otg_softc *sc, struct saf1761_otg_td *td)
|
|
{
|
|
uint32_t pdt_addr;
|
|
uint32_t status;
|
|
uint32_t count;
|
|
uint32_t temp;
|
|
|
|
if (td->channel < SOTG_HOST_CHANNEL_MAX) {
|
|
pdt_addr = SOTG_PTD(td->channel);
|
|
|
|
status = saf1761_peek_host_memory_le_4(sc, pdt_addr + SOTG_PTD_DW3);
|
|
DPRINTFN(5, "STATUS=0x%08x\n", status);
|
|
|
|
if (status & SOTG_PTD_DW3_ACTIVE) {
|
|
goto busy;
|
|
} else if (status & SOTG_PTD_DW3_HALTED) {
|
|
td->error_stall = 1;
|
|
td->error_any = 1;
|
|
} else if (status & SOTG_PTD_DW3_ERRORS) {
|
|
td->error_any = 1;
|
|
}
|
|
count = (status & SOTG_PTD_DW3_XFER_COUNT);
|
|
|
|
saf1761_host_channel_free(sc, td);
|
|
goto complete;
|
|
}
|
|
if (saf1761_host_channel_alloc(sc, td))
|
|
goto busy;
|
|
|
|
count = 8;
|
|
|
|
if (count != td->remainder) {
|
|
td->error_any = 1;
|
|
goto complete;
|
|
}
|
|
|
|
saf1761_write_host_memory(sc, td, count);
|
|
|
|
pdt_addr = SOTG_PTD(td->channel);
|
|
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW7, 0);
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW6, 0);
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW5, 0);
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW4, 0);
|
|
|
|
temp = SOTG_PTD_DW3_ACTIVE | (td->toggle << 25) | SOTG_PTD_DW3_CERR;
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW3, temp);
|
|
|
|
temp = SOTG_HC_MEMORY_ADDR(SOTG_DATA_ADDR(td->channel)) << 8;
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW2, temp);
|
|
|
|
temp = td->dw1_value | (2 << 10) /* SETUP PID */ | (td->ep_index >> 1);
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW1, temp);
|
|
|
|
temp = (td->ep_index << 31) | (1 << 29) /* pkt-multiplier */ |
|
|
(td->max_packet_size << 18) /* wMaxPacketSize */ |
|
|
(count << 3) /* transfer count */ |
|
|
SOTG_PTD_DW0_VALID;
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW0, temp);
|
|
|
|
td->toggle = 1;
|
|
busy:
|
|
return (1); /* busy */
|
|
complete:
|
|
return (0); /* complete */
|
|
}
|
|
|
|
static uint8_t
|
|
saf1761_host_bulk_data_rx(struct saf1761_otg_softc *sc, struct saf1761_otg_td *td)
|
|
{
|
|
uint32_t pdt_addr;
|
|
uint32_t temp;
|
|
|
|
if (td->channel < SOTG_HOST_CHANNEL_MAX) {
|
|
uint32_t status;
|
|
uint32_t count;
|
|
uint8_t got_short;
|
|
|
|
pdt_addr = SOTG_PTD(td->channel);
|
|
|
|
status = saf1761_peek_host_memory_le_4(sc, pdt_addr + SOTG_PTD_DW3);
|
|
DPRINTFN(5, "STATUS=0x%08x\n", status);
|
|
|
|
if (status & SOTG_PTD_DW3_ACTIVE) {
|
|
goto busy;
|
|
} else if (status & SOTG_PTD_DW3_HALTED) {
|
|
td->error_stall = 1;
|
|
td->error_any = 1;
|
|
goto complete;
|
|
} else if (status & SOTG_PTD_DW3_ERRORS) {
|
|
td->error_any = 1;
|
|
goto complete;
|
|
}
|
|
count = (status & SOTG_PTD_DW3_XFER_COUNT);
|
|
got_short = 0;
|
|
|
|
/* verify the packet byte count */
|
|
if (count != td->max_packet_size) {
|
|
if (count < td->max_packet_size) {
|
|
/* we have a short packet */
|
|
td->short_pkt = 1;
|
|
got_short = 1;
|
|
} else {
|
|
/* invalid USB packet */
|
|
td->error_any = 1;
|
|
goto complete;
|
|
}
|
|
}
|
|
td->toggle ^= 1;
|
|
|
|
/* verify the packet byte count */
|
|
if (count > td->remainder) {
|
|
/* invalid USB packet */
|
|
td->error_any = 1;
|
|
goto complete;
|
|
}
|
|
|
|
saf1761_read_host_memory(sc, td, count);
|
|
|
|
saf1761_host_channel_free(sc, td);
|
|
|
|
/* check if we are complete */
|
|
if ((td->remainder == 0) || got_short) {
|
|
if (td->short_pkt)
|
|
goto complete;
|
|
/* else need to receive a zero length packet */
|
|
}
|
|
}
|
|
if (saf1761_host_channel_alloc(sc, td))
|
|
goto busy;
|
|
|
|
/* set toggle, if any */
|
|
if (td->set_toggle) {
|
|
td->set_toggle = 0;
|
|
td->toggle = 1;
|
|
}
|
|
|
|
/* receive one more packet */
|
|
|
|
pdt_addr = SOTG_PTD(td->channel);
|
|
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW7, 0);
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW6, 0);
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW5, 0);
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW4, 0);
|
|
|
|
temp = SOTG_PTD_DW3_ACTIVE | (td->toggle << 25) | SOTG_PTD_DW3_CERR;
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW3, temp);
|
|
|
|
temp = SOTG_HC_MEMORY_ADDR(SOTG_DATA_ADDR(td->channel)) << 8;
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW2, temp);
|
|
|
|
temp = td->dw1_value | (1 << 10) /* IN-PID */ | (td->ep_index >> 1);
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW1, temp);
|
|
|
|
temp = (td->ep_index << 31) | (1 << 29) /* pkt-multiplier */ |
|
|
(td->max_packet_size << 18) /* wMaxPacketSize */ |
|
|
(td->max_packet_size << 3) /* transfer count */ |
|
|
SOTG_PTD_DW0_VALID;
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW0, temp);
|
|
busy:
|
|
return (1); /* busy */
|
|
complete:
|
|
return (0); /* complete */
|
|
}
|
|
|
|
static uint8_t
|
|
saf1761_host_bulk_data_tx(struct saf1761_otg_softc *sc, struct saf1761_otg_td *td)
|
|
{
|
|
uint32_t pdt_addr;
|
|
uint32_t temp;
|
|
uint32_t count;
|
|
|
|
if (td->channel < SOTG_HOST_CHANNEL_MAX) {
|
|
uint32_t status;
|
|
|
|
pdt_addr = SOTG_PTD(td->channel);
|
|
|
|
status = saf1761_peek_host_memory_le_4(sc, pdt_addr + SOTG_PTD_DW3);
|
|
DPRINTFN(5, "STATUS=0x%08x\n", status);
|
|
|
|
if (status & SOTG_PTD_DW3_ACTIVE) {
|
|
goto busy;
|
|
} else if (status & SOTG_PTD_DW3_HALTED) {
|
|
td->error_stall = 1;
|
|
td->error_any = 1;
|
|
} else if (status & SOTG_PTD_DW3_ERRORS) {
|
|
td->error_any = 1;
|
|
}
|
|
|
|
saf1761_host_channel_free(sc, td);
|
|
|
|
/* check remainder */
|
|
if (td->remainder == 0) {
|
|
if (td->short_pkt)
|
|
goto complete;
|
|
/* else we need to transmit a short packet */
|
|
}
|
|
}
|
|
if (saf1761_host_channel_alloc(sc, td))
|
|
goto busy;
|
|
|
|
count = td->max_packet_size;
|
|
if (td->remainder < count) {
|
|
/* we have a short packet */
|
|
td->short_pkt = 1;
|
|
count = td->remainder;
|
|
}
|
|
|
|
saf1761_write_host_memory(sc, td, count);
|
|
|
|
/* set toggle, if any */
|
|
if (td->set_toggle) {
|
|
td->set_toggle = 0;
|
|
td->toggle = 1;
|
|
}
|
|
|
|
/* send one more packet */
|
|
|
|
pdt_addr = SOTG_PTD(td->channel);
|
|
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW7, 0);
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW6, 0);
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW5, 0);
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW4, 0);
|
|
|
|
temp = SOTG_PTD_DW3_ACTIVE | (td->toggle << 25) | SOTG_PTD_DW3_CERR;
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW3, temp);
|
|
|
|
temp = SOTG_HC_MEMORY_ADDR(SOTG_DATA_ADDR(td->channel)) << 8;
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW2, temp);
|
|
|
|
temp = td->dw1_value | (0 << 10) /* OUT-PID */ | (td->ep_index >> 1);
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW1, temp);
|
|
|
|
temp = (td->ep_index << 31) | (1 << 29) /* pkt-multiplier */ |
|
|
(td->max_packet_size << 18) /* wMaxPacketSize */ |
|
|
(count << 3) /* transfer count */ |
|
|
SOTG_PTD_DW0_VALID;
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW0, temp);
|
|
|
|
td->toggle ^= 1;
|
|
busy:
|
|
return (1); /* busy */
|
|
complete:
|
|
return (0); /* complete */
|
|
}
|
|
|
|
static uint8_t
|
|
saf1761_host_intr_data_rx(struct saf1761_otg_softc *sc, struct saf1761_otg_td *td)
|
|
{
|
|
uint32_t pdt_addr;
|
|
uint32_t temp;
|
|
|
|
if (td->channel < SOTG_HOST_CHANNEL_MAX) {
|
|
uint32_t status;
|
|
uint32_t count;
|
|
uint8_t got_short;
|
|
|
|
pdt_addr = SOTG_PTD(td->channel);
|
|
|
|
status = saf1761_peek_host_memory_le_4(sc, pdt_addr + SOTG_PTD_DW3);
|
|
DPRINTFN(5, "STATUS=0x%08x\n", status);
|
|
|
|
if (status & SOTG_PTD_DW3_ACTIVE) {
|
|
goto busy;
|
|
} else if (status & SOTG_PTD_DW3_HALTED) {
|
|
td->error_stall = 1;
|
|
td->error_any = 1;
|
|
goto complete;
|
|
}
|
|
|
|
count = (status & SOTG_PTD_DW3_XFER_COUNT);
|
|
got_short = 0;
|
|
|
|
/* verify the packet byte count */
|
|
if (count != td->max_packet_size) {
|
|
if (count < td->max_packet_size) {
|
|
/* we have a short packet */
|
|
td->short_pkt = 1;
|
|
got_short = 1;
|
|
} else {
|
|
/* invalid USB packet */
|
|
td->error_any = 1;
|
|
goto complete;
|
|
}
|
|
}
|
|
td->toggle ^= 1;
|
|
|
|
/* verify the packet byte count */
|
|
if (count > td->remainder) {
|
|
/* invalid USB packet */
|
|
td->error_any = 1;
|
|
goto complete;
|
|
}
|
|
|
|
saf1761_read_host_memory(sc, td, count);
|
|
|
|
saf1761_host_channel_free(sc, td);
|
|
|
|
/* check if we are complete */
|
|
if ((td->remainder == 0) || got_short) {
|
|
if (td->short_pkt)
|
|
goto complete;
|
|
/* else need to receive a zero length packet */
|
|
}
|
|
}
|
|
if (saf1761_host_channel_alloc(sc, td))
|
|
goto busy;
|
|
|
|
/* set toggle, if any */
|
|
if (td->set_toggle) {
|
|
td->set_toggle = 0;
|
|
td->toggle = 1;
|
|
}
|
|
|
|
/* receive one more packet */
|
|
|
|
pdt_addr = SOTG_PTD(td->channel);
|
|
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW7, 0);
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW6, 0);
|
|
|
|
temp = (0xFC << td->uframe) & 0xFF; /* complete split */
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW5, temp);
|
|
|
|
temp = (1U << td->uframe); /* start split */
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW4, temp);
|
|
|
|
temp = SOTG_PTD_DW3_ACTIVE | (td->toggle << 25) | SOTG_PTD_DW3_CERR;
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW3, temp);
|
|
|
|
temp = (SOTG_HC_MEMORY_ADDR(SOTG_DATA_ADDR(td->channel)) << 8) | (td->interval & 0xF8);
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW2, temp);
|
|
|
|
temp = td->dw1_value | (1 << 10) /* IN-PID */ | (td->ep_index >> 1);
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW1, temp);
|
|
|
|
temp = (td->ep_index << 31) | (1 << 29) /* pkt-multiplier */ |
|
|
(td->max_packet_size << 18) /* wMaxPacketSize */ |
|
|
(td->max_packet_size << 3) /* transfer count */ |
|
|
SOTG_PTD_DW0_VALID;
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW0, temp);
|
|
busy:
|
|
return (1); /* busy */
|
|
complete:
|
|
return (0); /* complete */
|
|
}
|
|
|
|
static uint8_t
|
|
saf1761_host_intr_data_tx(struct saf1761_otg_softc *sc, struct saf1761_otg_td *td)
|
|
{
|
|
uint32_t pdt_addr;
|
|
uint32_t temp;
|
|
uint32_t count;
|
|
|
|
if (td->channel < SOTG_HOST_CHANNEL_MAX) {
|
|
uint32_t status;
|
|
|
|
pdt_addr = SOTG_PTD(td->channel);
|
|
|
|
status = saf1761_peek_host_memory_le_4(sc, pdt_addr + SOTG_PTD_DW3);
|
|
DPRINTFN(5, "STATUS=0x%08x\n", status);
|
|
|
|
if (status & SOTG_PTD_DW3_ACTIVE) {
|
|
goto busy;
|
|
} else if (status & SOTG_PTD_DW3_HALTED) {
|
|
td->error_stall = 1;
|
|
td->error_any = 1;
|
|
}
|
|
|
|
saf1761_host_channel_free(sc, td);
|
|
|
|
/* check remainder */
|
|
if (td->remainder == 0) {
|
|
if (td->short_pkt)
|
|
goto complete;
|
|
/* else we need to transmit a short packet */
|
|
}
|
|
}
|
|
if (saf1761_host_channel_alloc(sc, td))
|
|
goto busy;
|
|
|
|
count = td->max_packet_size;
|
|
if (td->remainder < count) {
|
|
/* we have a short packet */
|
|
td->short_pkt = 1;
|
|
count = td->remainder;
|
|
}
|
|
|
|
saf1761_write_host_memory(sc, td, count);
|
|
|
|
/* set toggle, if any */
|
|
if (td->set_toggle) {
|
|
td->set_toggle = 0;
|
|
td->toggle = 1;
|
|
}
|
|
|
|
/* send one more packet */
|
|
|
|
pdt_addr = SOTG_PTD(td->channel);
|
|
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW7, 0);
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW6, 0);
|
|
|
|
temp = (0xFC << td->uframe) & 0xFF; /* complete split */
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW5, temp);
|
|
|
|
temp = (1U << td->uframe); /* start split */
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW4, temp);
|
|
|
|
temp = SOTG_PTD_DW3_ACTIVE | (td->toggle << 25) | SOTG_PTD_DW3_CERR;
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW3, temp);
|
|
|
|
temp = (SOTG_HC_MEMORY_ADDR(SOTG_DATA_ADDR(td->channel)) << 8) | (td->interval & 0xF8);
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW2, temp);
|
|
|
|
temp = td->dw1_value | (0 << 10) /* OUT-PID */ | (td->ep_index >> 1);
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW1, temp);
|
|
|
|
temp = (td->ep_index << 31) | (1 << 29) /* pkt-multiplier */ |
|
|
(td->max_packet_size << 18) /* wMaxPacketSize */ |
|
|
(count << 3) /* transfer count */ |
|
|
SOTG_PTD_DW0_VALID;
|
|
SAF1761_WRITE_LE_4(sc, pdt_addr + SOTG_PTD_DW0, temp);
|
|
|
|
td->toggle ^= 1;
|
|
busy:
|
|
return (1); /* busy */
|
|
complete:
|
|
return (0); /* complete */
|
|
}
|
|
|
|
static uint8_t
|
|
saf1761_host_isoc_data_rx(struct saf1761_otg_softc *sc, struct saf1761_otg_td *td)
|
|
{
|
|
return (1); /* busy */
|
|
}
|
|
|
|
static uint8_t
|
|
saf1761_host_isoc_data_tx(struct saf1761_otg_softc *sc, struct saf1761_otg_td *td)
|
|
{
|
|
return (1); /* busy */
|
|
}
|
|
|
|
static void
|
|
saf1761_otg_set_address(struct saf1761_otg_softc *sc, uint8_t addr)
|
|
{
|
|
DPRINTFN(5, "addr=%d\n", addr);
|
|
|
|
SAF1761_WRITE_LE_4(sc, SOTG_ADDRESS, addr | SOTG_ADDRESS_ENABLE);
|
|
}
|
|
|
|
|
|
static void
|
|
saf1761_read_device_fifo(struct saf1761_otg_softc *sc,
|
|
struct saf1761_otg_td *td, uint32_t len)
|
|
{
|
|
struct usb_page_search buf_res;
|
|
uint32_t count;
|
|
|
|
/* optimised read first */
|
|
while (len > 0) {
|
|
usbd_get_page(td->pc, td->offset, &buf_res);
|
|
|
|
/* get correct length */
|
|
if (buf_res.length > len)
|
|
buf_res.length = len;
|
|
|
|
/* check buffer alignment */
|
|
if (((uintptr_t)buf_res.buffer) & 3)
|
|
break;
|
|
|
|
count = buf_res.length & ~3;
|
|
if (count == 0)
|
|
break;
|
|
|
|
bus_space_read_multi_4((sc)->sc_io_tag, (sc)->sc_io_hdl,
|
|
SOTG_DATA_PORT, buf_res.buffer, count / 4);
|
|
|
|
len -= count;
|
|
|
|
/* update remainder and offset */
|
|
td->remainder -= count;
|
|
td->offset += count;
|
|
}
|
|
|
|
if (len > 0) {
|
|
/* use bounce buffer */
|
|
bus_space_read_multi_4((sc)->sc_io_tag, (sc)->sc_io_hdl,
|
|
SOTG_DATA_PORT, sc->sc_bounce_buffer, (len + 3) / 4);
|
|
usbd_copy_in(td->pc, td->offset,
|
|
sc->sc_bounce_buffer, len);
|
|
|
|
/* update remainder and offset */
|
|
td->remainder -= len;
|
|
td->offset += len;
|
|
}
|
|
}
|
|
|
|
static void
|
|
saf1761_write_device_fifo(struct saf1761_otg_softc *sc,
|
|
struct saf1761_otg_td *td, uint32_t len)
|
|
{
|
|
struct usb_page_search buf_res;
|
|
uint32_t count;
|
|
|
|
/* optimised write first */
|
|
while (len > 0) {
|
|
usbd_get_page(td->pc, td->offset, &buf_res);
|
|
|
|
/* get correct length */
|
|
if (buf_res.length > len)
|
|
buf_res.length = len;
|
|
|
|
/* check buffer alignment */
|
|
if (((uintptr_t)buf_res.buffer) & 3)
|
|
break;
|
|
|
|
count = buf_res.length & ~3;
|
|
if (count == 0)
|
|
break;
|
|
|
|
bus_space_write_multi_4((sc)->sc_io_tag, (sc)->sc_io_hdl,
|
|
SOTG_DATA_PORT, buf_res.buffer, count / 4);
|
|
|
|
len -= count;
|
|
|
|
/* update remainder and offset */
|
|
td->remainder -= count;
|
|
td->offset += count;
|
|
}
|
|
if (len > 0) {
|
|
/* use bounce buffer */
|
|
usbd_copy_out(td->pc, td->offset, sc->sc_bounce_buffer, len);
|
|
bus_space_write_multi_4((sc)->sc_io_tag, (sc)->sc_io_hdl,
|
|
SOTG_DATA_PORT, sc->sc_bounce_buffer, (len + 3) / 4);
|
|
|
|
/* update remainder and offset */
|
|
td->remainder -= len;
|
|
td->offset += len;
|
|
}
|
|
}
|
|
|
|
static uint8_t
|
|
saf1761_device_setup_rx(struct saf1761_otg_softc *sc, struct saf1761_otg_td *td)
|
|
{
|
|
struct usb_device_request req;
|
|
uint32_t count;
|
|
|
|
/* select the correct endpoint */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_EP_INDEX, SOTG_EP_INDEX_EP0SETUP);
|
|
|
|
count = SAF1761_READ_LE_4(sc, SOTG_BUF_LENGTH);
|
|
|
|
/* check buffer status */
|
|
if ((count & SOTG_BUF_LENGTH_FILLED_MASK) == 0)
|
|
goto busy;
|
|
|
|
/* get buffer length */
|
|
count &= SOTG_BUF_LENGTH_BUFLEN_MASK;
|
|
|
|
DPRINTFN(5, "count=%u rem=%u\n", count, td->remainder);
|
|
|
|
/* clear did stall */
|
|
td->did_stall = 0;
|
|
|
|
/* clear stall */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_CTRL_FUNC, 0);
|
|
|
|
/* verify data length */
|
|
if (count != td->remainder) {
|
|
DPRINTFN(0, "Invalid SETUP packet "
|
|
"length, %d bytes\n", count);
|
|
goto busy;
|
|
}
|
|
if (count != sizeof(req)) {
|
|
DPRINTFN(0, "Unsupported SETUP packet "
|
|
"length, %d bytes\n", count);
|
|
goto busy;
|
|
}
|
|
/* receive data */
|
|
saf1761_read_device_fifo(sc, td, sizeof(req));
|
|
|
|
/* extract SETUP packet again */
|
|
usbd_copy_out(td->pc, 0, &req, sizeof(req));
|
|
|
|
/* sneak peek the set address request */
|
|
if ((req.bmRequestType == UT_WRITE_DEVICE) &&
|
|
(req.bRequest == UR_SET_ADDRESS)) {
|
|
sc->sc_dv_addr = req.wValue[0] & 0x7F;
|
|
DPRINTF("Set address %d\n", sc->sc_dv_addr);
|
|
} else {
|
|
sc->sc_dv_addr = 0xFF;
|
|
}
|
|
return (0); /* complete */
|
|
|
|
busy:
|
|
/* abort any ongoing transfer */
|
|
if (!td->did_stall) {
|
|
DPRINTFN(5, "stalling\n");
|
|
|
|
/* set stall */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_CTRL_FUNC, SOTG_CTRL_FUNC_STALL);
|
|
|
|
td->did_stall = 1;
|
|
}
|
|
return (1); /* not complete */
|
|
}
|
|
|
|
static uint8_t
|
|
saf1761_device_data_rx(struct saf1761_otg_softc *sc, struct saf1761_otg_td *td)
|
|
{
|
|
uint32_t count;
|
|
uint8_t got_short = 0;
|
|
|
|
if (td->ep_index == 0) {
|
|
/* select the correct endpoint */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_EP_INDEX, SOTG_EP_INDEX_EP0SETUP);
|
|
|
|
count = SAF1761_READ_LE_4(sc, SOTG_BUF_LENGTH);
|
|
|
|
/* check buffer status */
|
|
if ((count & SOTG_BUF_LENGTH_FILLED_MASK) != 0) {
|
|
|
|
if (td->remainder == 0) {
|
|
/*
|
|
* We are actually complete and have
|
|
* received the next SETUP:
|
|
*/
|
|
DPRINTFN(5, "faking complete\n");
|
|
return (0); /* complete */
|
|
}
|
|
DPRINTFN(5, "SETUP packet while receiving data\n");
|
|
/*
|
|
* USB Host Aborted the transfer.
|
|
*/
|
|
td->error_any = 1;
|
|
return (0); /* complete */
|
|
}
|
|
}
|
|
/* select the correct endpoint */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_EP_INDEX,
|
|
(td->ep_index << SOTG_EP_INDEX_ENDP_INDEX_SHIFT) |
|
|
SOTG_EP_INDEX_DIR_OUT);
|
|
|
|
/* enable data stage */
|
|
if (td->set_toggle) {
|
|
td->set_toggle = 0;
|
|
SAF1761_WRITE_LE_4(sc, SOTG_CTRL_FUNC, SOTG_CTRL_FUNC_DSEN);
|
|
}
|
|
|
|
count = SAF1761_READ_LE_4(sc, SOTG_BUF_LENGTH);
|
|
|
|
/* check buffer status */
|
|
if ((count & SOTG_BUF_LENGTH_FILLED_MASK) == 0)
|
|
return (1); /* not complete */
|
|
|
|
/* get buffer length */
|
|
count &= SOTG_BUF_LENGTH_BUFLEN_MASK;
|
|
|
|
DPRINTFN(5, "rem=%u count=0x%04x\n", td->remainder, count);
|
|
|
|
/* verify the packet byte count */
|
|
if (count != td->max_packet_size) {
|
|
if (count < td->max_packet_size) {
|
|
/* we have a short packet */
|
|
td->short_pkt = 1;
|
|
got_short = 1;
|
|
} else {
|
|
/* invalid USB packet */
|
|
td->error_any = 1;
|
|
return (0); /* we are complete */
|
|
}
|
|
}
|
|
/* verify the packet byte count */
|
|
if (count > td->remainder) {
|
|
/* invalid USB packet */
|
|
td->error_any = 1;
|
|
return (0); /* we are complete */
|
|
}
|
|
/* receive data */
|
|
saf1761_read_device_fifo(sc, td, count);
|
|
|
|
/* check if we are complete */
|
|
if ((td->remainder == 0) || got_short) {
|
|
if (td->short_pkt) {
|
|
/* we are complete */
|
|
return (0);
|
|
}
|
|
/* else need to receive a zero length packet */
|
|
}
|
|
return (1); /* not complete */
|
|
}
|
|
|
|
static uint8_t
|
|
saf1761_device_data_tx(struct saf1761_otg_softc *sc, struct saf1761_otg_td *td)
|
|
{
|
|
uint32_t count;
|
|
|
|
if (td->ep_index == 0) {
|
|
/* select the correct endpoint */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_EP_INDEX, SOTG_EP_INDEX_EP0SETUP);
|
|
|
|
count = SAF1761_READ_LE_4(sc, SOTG_BUF_LENGTH);
|
|
|
|
/* check buffer status */
|
|
if ((count & SOTG_BUF_LENGTH_FILLED_MASK) != 0) {
|
|
DPRINTFN(5, "SETUP abort\n");
|
|
/*
|
|
* USB Host Aborted the transfer.
|
|
*/
|
|
td->error_any = 1;
|
|
return (0); /* complete */
|
|
}
|
|
}
|
|
/* select the correct endpoint */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_EP_INDEX,
|
|
(td->ep_index << SOTG_EP_INDEX_ENDP_INDEX_SHIFT) |
|
|
SOTG_EP_INDEX_DIR_IN);
|
|
|
|
count = SAF1761_READ_LE_4(sc, SOTG_BUF_LENGTH);
|
|
|
|
/* check buffer status */
|
|
if ((count & SOTG_BUF_LENGTH_FILLED_MASK) != 0)
|
|
return (1); /* not complete */
|
|
|
|
/* enable data stage */
|
|
if (td->set_toggle) {
|
|
td->set_toggle = 0;
|
|
SAF1761_WRITE_LE_4(sc, SOTG_CTRL_FUNC, SOTG_CTRL_FUNC_DSEN);
|
|
}
|
|
|
|
DPRINTFN(5, "rem=%u\n", td->remainder);
|
|
|
|
count = td->max_packet_size;
|
|
if (td->remainder < count) {
|
|
/* we have a short packet */
|
|
td->short_pkt = 1;
|
|
count = td->remainder;
|
|
}
|
|
/* transmit data */
|
|
saf1761_write_device_fifo(sc, td, count);
|
|
|
|
if (td->ep_index == 0) {
|
|
if (count < SOTG_FS_MAX_PACKET_SIZE) {
|
|
/* set end of packet */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_CTRL_FUNC, SOTG_CTRL_FUNC_VENDP);
|
|
}
|
|
} else {
|
|
if (count < SOTG_HS_MAX_PACKET_SIZE) {
|
|
/* set end of packet */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_CTRL_FUNC, SOTG_CTRL_FUNC_VENDP);
|
|
}
|
|
}
|
|
|
|
/* check remainder */
|
|
if (td->remainder == 0) {
|
|
if (td->short_pkt) {
|
|
return (0); /* complete */
|
|
}
|
|
/* else we need to transmit a short packet */
|
|
}
|
|
return (1); /* not complete */
|
|
}
|
|
|
|
static uint8_t
|
|
saf1761_device_data_tx_sync(struct saf1761_otg_softc *sc, struct saf1761_otg_td *td)
|
|
{
|
|
uint32_t count;
|
|
|
|
if (td->ep_index == 0) {
|
|
/* select the correct endpoint */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_EP_INDEX, SOTG_EP_INDEX_EP0SETUP);
|
|
|
|
count = SAF1761_READ_LE_4(sc, SOTG_BUF_LENGTH);
|
|
|
|
/* check buffer status */
|
|
if ((count & SOTG_BUF_LENGTH_FILLED_MASK) != 0) {
|
|
DPRINTFN(5, "Faking complete\n");
|
|
return (0); /* complete */
|
|
}
|
|
}
|
|
/* select the correct endpoint */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_EP_INDEX,
|
|
(td->ep_index << SOTG_EP_INDEX_ENDP_INDEX_SHIFT) |
|
|
SOTG_EP_INDEX_DIR_IN);
|
|
|
|
count = SAF1761_READ_LE_4(sc, SOTG_BUF_LENGTH);
|
|
|
|
/* check buffer status */
|
|
if ((count & SOTG_BUF_LENGTH_FILLED_MASK) != 0)
|
|
return (1); /* busy */
|
|
|
|
if (sc->sc_dv_addr != 0xFF) {
|
|
/* write function address */
|
|
saf1761_otg_set_address(sc, sc->sc_dv_addr);
|
|
}
|
|
return (0); /* complete */
|
|
}
|
|
|
|
static uint8_t
|
|
saf1761_otg_xfer_do_fifo(struct saf1761_otg_softc *sc, struct usb_xfer *xfer)
|
|
{
|
|
struct saf1761_otg_td *td;
|
|
uint8_t toggle;
|
|
|
|
DPRINTFN(9, "\n");
|
|
|
|
td = xfer->td_transfer_cache;
|
|
while (1) {
|
|
if ((td->func) (sc, td)) {
|
|
/* operation in progress */
|
|
break;
|
|
}
|
|
if (((void *)td) == xfer->td_transfer_last) {
|
|
goto done;
|
|
}
|
|
if (td->error_any) {
|
|
goto done;
|
|
} else if (td->remainder > 0) {
|
|
/*
|
|
* We had a short transfer. If there is no alternate
|
|
* next, stop processing !
|
|
*/
|
|
if (!td->alt_next) {
|
|
goto done;
|
|
}
|
|
}
|
|
/*
|
|
* Fetch the next transfer descriptor.
|
|
*/
|
|
toggle = td->toggle;
|
|
td = td->obj_next;
|
|
td->toggle = toggle;
|
|
xfer->td_transfer_cache = td;
|
|
}
|
|
return (1); /* not complete */
|
|
|
|
done:
|
|
/* compute all actual lengths */
|
|
|
|
saf1761_otg_standard_done(xfer);
|
|
|
|
return (0); /* complete */
|
|
}
|
|
|
|
static void
|
|
saf1761_otg_interrupt_poll(struct saf1761_otg_softc *sc)
|
|
{
|
|
struct usb_xfer *xfer;
|
|
|
|
repeat:
|
|
TAILQ_FOREACH(xfer, &sc->sc_bus.intr_q.head, wait_entry) {
|
|
if (!saf1761_otg_xfer_do_fifo(sc, xfer)) {
|
|
/* queue has been modified */
|
|
goto repeat;
|
|
}
|
|
}
|
|
}
|
|
|
|
static void
|
|
saf1761_otg_wait_suspend(struct saf1761_otg_softc *sc, uint8_t on)
|
|
{
|
|
if (on) {
|
|
sc->sc_intr_enable |= SOTG_DCINTERRUPT_IESUSP;
|
|
sc->sc_intr_enable &= ~SOTG_DCINTERRUPT_IERESM;
|
|
} else {
|
|
sc->sc_intr_enable &= ~SOTG_DCINTERRUPT_IESUSP;
|
|
sc->sc_intr_enable |= SOTG_DCINTERRUPT_IERESM;
|
|
}
|
|
SAF1761_WRITE_LE_4(sc, SOTG_DCINTERRUPT_EN, sc->sc_intr_enable);
|
|
}
|
|
|
|
static void
|
|
saf1761_otg_update_vbus(struct saf1761_otg_softc *sc)
|
|
{
|
|
uint16_t status;
|
|
|
|
/* read fresh status */
|
|
status = SAF1761_READ_LE_4(sc, SOTG_STATUS);
|
|
|
|
DPRINTFN(4, "STATUS=0x%04x\n", status);
|
|
|
|
if ((status & SOTG_STATUS_VBUS_VLD) &&
|
|
(status & SOTG_STATUS_ID)) {
|
|
/* VBUS present and device mode */
|
|
if (!sc->sc_flags.status_vbus) {
|
|
sc->sc_flags.status_vbus = 1;
|
|
|
|
/* complete root HUB interrupt endpoint */
|
|
saf1761_otg_root_intr(sc);
|
|
}
|
|
} else {
|
|
/* VBUS not-present or host mode */
|
|
if (sc->sc_flags.status_vbus) {
|
|
sc->sc_flags.status_vbus = 0;
|
|
sc->sc_flags.status_bus_reset = 0;
|
|
sc->sc_flags.status_suspend = 0;
|
|
sc->sc_flags.change_suspend = 0;
|
|
sc->sc_flags.change_connect = 1;
|
|
|
|
/* complete root HUB interrupt endpoint */
|
|
saf1761_otg_root_intr(sc);
|
|
}
|
|
}
|
|
}
|
|
|
|
void
|
|
saf1761_otg_interrupt(struct saf1761_otg_softc *sc)
|
|
{
|
|
uint32_t status;
|
|
uint32_t hcstat;
|
|
|
|
USB_BUS_LOCK(&sc->sc_bus);
|
|
|
|
hcstat = SAF1761_READ_LE_4(sc, SOTG_HCINTERRUPT);
|
|
/* acknowledge all host controller interrupts */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_HCINTERRUPT, hcstat);
|
|
|
|
status = SAF1761_READ_LE_4(sc, SOTG_DCINTERRUPT);
|
|
/* acknowledge all device controller interrupts */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_DCINTERRUPT, status);
|
|
|
|
DPRINTF("DCINTERRUPT=0x%08x HCINTERRUPT=0x%08x SOF=0x%08x "
|
|
"FRINDEX=0x%08x\n", status, hcstat,
|
|
SAF1761_READ_LE_4(sc, SOTG_FRAME_NUM),
|
|
SAF1761_READ_LE_4(sc, SOTG_FRINDEX));
|
|
|
|
/* update VBUS and ID bits, if any */
|
|
if (status & SOTG_DCINTERRUPT_IEVBUS) {
|
|
saf1761_otg_update_vbus(sc);
|
|
}
|
|
|
|
if (status & SOTG_DCINTERRUPT_IEBRST) {
|
|
/* unlock device */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_UNLOCK_DEVICE,
|
|
SOTG_UNLOCK_DEVICE_CODE);
|
|
|
|
/* Enable device address */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_ADDRESS,
|
|
SOTG_ADDRESS_ENABLE);
|
|
|
|
sc->sc_flags.status_bus_reset = 1;
|
|
sc->sc_flags.status_suspend = 0;
|
|
sc->sc_flags.change_suspend = 0;
|
|
sc->sc_flags.change_connect = 1;
|
|
|
|
/* disable resume interrupt */
|
|
saf1761_otg_wait_suspend(sc, 1);
|
|
/* complete root HUB interrupt endpoint */
|
|
saf1761_otg_root_intr(sc);
|
|
}
|
|
/*
|
|
* If "RESUME" and "SUSPEND" is set at the same time we
|
|
* interpret that like "RESUME". Resume is set when there is
|
|
* at least 3 milliseconds of inactivity on the USB BUS:
|
|
*/
|
|
if (status & SOTG_DCINTERRUPT_IERESM) {
|
|
/* unlock device */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_UNLOCK_DEVICE,
|
|
SOTG_UNLOCK_DEVICE_CODE);
|
|
|
|
if (sc->sc_flags.status_suspend) {
|
|
sc->sc_flags.status_suspend = 0;
|
|
sc->sc_flags.change_suspend = 1;
|
|
/* disable resume interrupt */
|
|
saf1761_otg_wait_suspend(sc, 1);
|
|
/* complete root HUB interrupt endpoint */
|
|
saf1761_otg_root_intr(sc);
|
|
}
|
|
} else if (status & SOTG_DCINTERRUPT_IESUSP) {
|
|
if (!sc->sc_flags.status_suspend) {
|
|
sc->sc_flags.status_suspend = 1;
|
|
sc->sc_flags.change_suspend = 1;
|
|
/* enable resume interrupt */
|
|
saf1761_otg_wait_suspend(sc, 0);
|
|
/* complete root HUB interrupt endpoint */
|
|
saf1761_otg_root_intr(sc);
|
|
}
|
|
}
|
|
/* poll all active transfers */
|
|
saf1761_otg_interrupt_poll(sc);
|
|
|
|
USB_BUS_UNLOCK(&sc->sc_bus);
|
|
}
|
|
|
|
static void
|
|
saf1761_otg_setup_standard_chain_sub(struct saf1761_otg_std_temp *temp)
|
|
{
|
|
struct saf1761_otg_td *td;
|
|
|
|
/* get current Transfer Descriptor */
|
|
td = temp->td_next;
|
|
temp->td = td;
|
|
|
|
/* prepare for next TD */
|
|
temp->td_next = td->obj_next;
|
|
|
|
/* fill out the Transfer Descriptor */
|
|
td->func = temp->func;
|
|
td->pc = temp->pc;
|
|
td->offset = temp->offset;
|
|
td->remainder = temp->len;
|
|
td->error_any = 0;
|
|
td->error_stall = 0;
|
|
td->set_toggle = 0;
|
|
td->did_stall = temp->did_stall;
|
|
td->short_pkt = temp->short_pkt;
|
|
td->alt_next = temp->setup_alt_next;
|
|
td->channel = SOTG_HOST_CHANNEL_MAX;
|
|
}
|
|
|
|
static void
|
|
saf1761_otg_setup_standard_chain(struct usb_xfer *xfer)
|
|
{
|
|
struct saf1761_otg_std_temp temp;
|
|
struct saf1761_otg_softc *sc;
|
|
struct saf1761_otg_td *td;
|
|
uint32_t x;
|
|
uint8_t ep_no;
|
|
uint8_t ep_type;
|
|
uint8_t need_sync;
|
|
uint8_t is_host;
|
|
|
|
DPRINTFN(9, "addr=%d endpt=%d sumlen=%d speed=%d\n",
|
|
xfer->address, UE_GET_ADDR(xfer->endpointno),
|
|
xfer->sumlen, usbd_get_speed(xfer->xroot->udev));
|
|
|
|
temp.max_frame_size = xfer->max_frame_size;
|
|
|
|
td = xfer->td_start[0];
|
|
xfer->td_transfer_first = td;
|
|
xfer->td_transfer_cache = td;
|
|
|
|
/* setup temp */
|
|
|
|
temp.pc = NULL;
|
|
temp.td = NULL;
|
|
temp.td_next = xfer->td_start[0];
|
|
temp.offset = 0;
|
|
temp.setup_alt_next = xfer->flags_int.short_frames_ok;
|
|
temp.did_stall = !xfer->flags_int.control_stall;
|
|
|
|
is_host = (xfer->xroot->udev->flags.usb_mode == USB_MODE_HOST);
|
|
|
|
sc = SAF1761_OTG_BUS2SC(xfer->xroot->bus);
|
|
ep_no = (xfer->endpointno & UE_ADDR);
|
|
ep_type = (xfer->endpoint->edesc->bmAttributes & UE_XFERTYPE);
|
|
|
|
/* check if we should prepend a setup message */
|
|
|
|
if (xfer->flags_int.control_xfr) {
|
|
if (xfer->flags_int.control_hdr) {
|
|
|
|
if (is_host)
|
|
temp.func = &saf1761_host_setup_tx;
|
|
else
|
|
temp.func = &saf1761_device_setup_rx;
|
|
|
|
temp.len = xfer->frlengths[0];
|
|
temp.pc = xfer->frbuffers + 0;
|
|
temp.short_pkt = temp.len ? 1 : 0;
|
|
/* check for last frame */
|
|
if (xfer->nframes == 1) {
|
|
/* no STATUS stage yet, SETUP is last */
|
|
if (xfer->flags_int.control_act)
|
|
temp.setup_alt_next = 0;
|
|
}
|
|
saf1761_otg_setup_standard_chain_sub(&temp);
|
|
}
|
|
x = 1;
|
|
} else {
|
|
x = 0;
|
|
}
|
|
|
|
if (x != xfer->nframes) {
|
|
if (xfer->endpointno & UE_DIR_IN) {
|
|
if (is_host) {
|
|
if (ep_type == UE_INTERRUPT)
|
|
temp.func = &saf1761_host_intr_data_rx;
|
|
else if (ep_type == UE_ISOCHRONOUS)
|
|
temp.func = &saf1761_host_isoc_data_rx;
|
|
else
|
|
temp.func = &saf1761_host_bulk_data_rx;
|
|
need_sync = 0;
|
|
} else {
|
|
temp.func = &saf1761_device_data_tx;
|
|
need_sync = 1;
|
|
}
|
|
} else {
|
|
if (is_host) {
|
|
if (ep_type == UE_INTERRUPT)
|
|
temp.func = &saf1761_host_intr_data_tx;
|
|
else if (ep_type == UE_ISOCHRONOUS)
|
|
temp.func = &saf1761_host_isoc_data_tx;
|
|
else
|
|
temp.func = &saf1761_host_bulk_data_tx;
|
|
need_sync = 0;
|
|
} else {
|
|
temp.func = &saf1761_device_data_rx;
|
|
need_sync = 0;
|
|
}
|
|
}
|
|
|
|
/* setup "pc" pointer */
|
|
temp.pc = xfer->frbuffers + x;
|
|
} else {
|
|
need_sync = 0;
|
|
}
|
|
|
|
while (x != xfer->nframes) {
|
|
|
|
/* DATA0 / DATA1 message */
|
|
|
|
temp.len = xfer->frlengths[x];
|
|
|
|
x++;
|
|
|
|
if (x == xfer->nframes) {
|
|
if (xfer->flags_int.control_xfr) {
|
|
if (xfer->flags_int.control_act) {
|
|
temp.setup_alt_next = 0;
|
|
}
|
|
} else {
|
|
temp.setup_alt_next = 0;
|
|
}
|
|
}
|
|
if (temp.len == 0) {
|
|
|
|
/* make sure that we send an USB packet */
|
|
|
|
temp.short_pkt = 0;
|
|
|
|
} else {
|
|
|
|
/* regular data transfer */
|
|
|
|
temp.short_pkt = (xfer->flags.force_short_xfer) ? 0 : 1;
|
|
}
|
|
|
|
saf1761_otg_setup_standard_chain_sub(&temp);
|
|
|
|
if (xfer->flags_int.isochronous_xfr) {
|
|
temp.offset += temp.len;
|
|
} else {
|
|
/* get next Page Cache pointer */
|
|
temp.pc = xfer->frbuffers + x;
|
|
}
|
|
}
|
|
|
|
/* check for control transfer */
|
|
if (xfer->flags_int.control_xfr) {
|
|
/* always setup a valid "pc" pointer for status and sync */
|
|
temp.pc = xfer->frbuffers + 0;
|
|
temp.len = 0;
|
|
temp.short_pkt = 0;
|
|
temp.setup_alt_next = 0;
|
|
|
|
/* check if we should append a status stage */
|
|
if (!xfer->flags_int.control_act) {
|
|
|
|
/*
|
|
* Send a DATA1 message and invert the current
|
|
* endpoint direction.
|
|
*/
|
|
if (xfer->endpointno & UE_DIR_IN) {
|
|
if (is_host) {
|
|
temp.func = &saf1761_host_bulk_data_tx;
|
|
need_sync = 0;
|
|
} else {
|
|
temp.func = &saf1761_device_data_rx;
|
|
need_sync = 0;
|
|
}
|
|
} else {
|
|
if (is_host) {
|
|
temp.func = &saf1761_host_bulk_data_rx;
|
|
need_sync = 0;
|
|
} else {
|
|
temp.func = &saf1761_device_data_tx;
|
|
need_sync = 1;
|
|
}
|
|
}
|
|
temp.len = 0;
|
|
temp.short_pkt = 0;
|
|
|
|
saf1761_otg_setup_standard_chain_sub(&temp);
|
|
|
|
/* data toggle should be DATA1 */
|
|
td = temp.td;
|
|
td->set_toggle = 1;
|
|
|
|
if (need_sync) {
|
|
/* we need a SYNC point after TX */
|
|
temp.func = &saf1761_device_data_tx_sync;
|
|
saf1761_otg_setup_standard_chain_sub(&temp);
|
|
}
|
|
}
|
|
} else {
|
|
if (need_sync) {
|
|
temp.pc = xfer->frbuffers + 0;
|
|
temp.len = 0;
|
|
temp.short_pkt = 0;
|
|
temp.setup_alt_next = 0;
|
|
|
|
/* we need a SYNC point after TX */
|
|
temp.func = &saf1761_device_data_tx_sync;
|
|
saf1761_otg_setup_standard_chain_sub(&temp);
|
|
}
|
|
}
|
|
|
|
/* must have at least one frame! */
|
|
td = temp.td;
|
|
xfer->td_transfer_last = td;
|
|
|
|
if (is_host) {
|
|
/* get first again */
|
|
td = xfer->td_transfer_first;
|
|
td->toggle = (xfer->endpoint->toggle_next ? 1 : 0);
|
|
}
|
|
}
|
|
|
|
static void
|
|
saf1761_otg_timeout(void *arg)
|
|
{
|
|
struct usb_xfer *xfer = arg;
|
|
|
|
DPRINTF("xfer=%p\n", xfer);
|
|
|
|
USB_BUS_LOCK_ASSERT(xfer->xroot->bus, MA_OWNED);
|
|
|
|
/* transfer is transferred */
|
|
saf1761_otg_device_done(xfer, USB_ERR_TIMEOUT);
|
|
}
|
|
|
|
static void
|
|
saf1761_otg_intr_set(struct usb_xfer *xfer, uint8_t set)
|
|
{
|
|
struct saf1761_otg_softc *sc = SAF1761_OTG_BUS2SC(xfer->xroot->bus);
|
|
uint8_t ep_no = (xfer->endpointno & UE_ADDR);
|
|
uint32_t mask;
|
|
|
|
DPRINTFN(15, "endpoint=%d set=%d\n", xfer->endpointno, set);
|
|
|
|
if (ep_no == 0) {
|
|
mask = SOTG_DCINTERRUPT_IEPRX(0) |
|
|
SOTG_DCINTERRUPT_IEPTX(0) |
|
|
SOTG_DCINTERRUPT_IEP0SETUP;
|
|
} else if (xfer->endpointno & UE_DIR_IN) {
|
|
mask = SOTG_DCINTERRUPT_IEPTX(ep_no);
|
|
} else {
|
|
mask = SOTG_DCINTERRUPT_IEPRX(ep_no);
|
|
}
|
|
|
|
if (set)
|
|
sc->sc_intr_enable |= mask;
|
|
else
|
|
sc->sc_intr_enable &= ~mask;
|
|
|
|
SAF1761_WRITE_LE_4(sc, SOTG_DCINTERRUPT_EN, sc->sc_intr_enable);
|
|
}
|
|
|
|
static void
|
|
saf1761_otg_start_standard_chain(struct usb_xfer *xfer)
|
|
{
|
|
struct saf1761_otg_softc *sc = SAF1761_OTG_BUS2SC(xfer->xroot->bus);
|
|
|
|
DPRINTFN(9, "\n");
|
|
|
|
/* poll one time */
|
|
if (saf1761_otg_xfer_do_fifo(sc, xfer)) {
|
|
|
|
/*
|
|
* Only enable the endpoint interrupt when we are
|
|
* actually waiting for data, hence we are dealing
|
|
* with level triggered interrupts !
|
|
*/
|
|
saf1761_otg_intr_set(xfer, 1);
|
|
|
|
/* put transfer on interrupt queue */
|
|
usbd_transfer_enqueue(&xfer->xroot->bus->intr_q, xfer);
|
|
|
|
/* start timeout, if any */
|
|
if (xfer->timeout != 0) {
|
|
usbd_transfer_timeout_ms(xfer,
|
|
&saf1761_otg_timeout, xfer->timeout);
|
|
}
|
|
}
|
|
}
|
|
|
|
static void
|
|
saf1761_otg_root_intr(struct saf1761_otg_softc *sc)
|
|
{
|
|
DPRINTFN(9, "\n");
|
|
|
|
USB_BUS_LOCK_ASSERT(&sc->sc_bus, MA_OWNED);
|
|
|
|
/* set port bit - we only have one port */
|
|
sc->sc_hub_idata[0] = 0x02;
|
|
|
|
uhub_root_intr(&sc->sc_bus, sc->sc_hub_idata,
|
|
sizeof(sc->sc_hub_idata));
|
|
}
|
|
|
|
static usb_error_t
|
|
saf1761_otg_standard_done_sub(struct usb_xfer *xfer)
|
|
{
|
|
struct saf1761_otg_td *td;
|
|
uint32_t len;
|
|
usb_error_t error;
|
|
|
|
DPRINTFN(9, "\n");
|
|
|
|
td = xfer->td_transfer_cache;
|
|
|
|
do {
|
|
len = td->remainder;
|
|
|
|
/* store last data toggle */
|
|
xfer->endpoint->toggle_next = td->toggle;
|
|
|
|
if (xfer->aframes != xfer->nframes) {
|
|
/*
|
|
* Verify the length and subtract
|
|
* the remainder from "frlengths[]":
|
|
*/
|
|
if (len > xfer->frlengths[xfer->aframes]) {
|
|
td->error_any = 1;
|
|
} else {
|
|
xfer->frlengths[xfer->aframes] -= len;
|
|
}
|
|
}
|
|
/* Check for transfer error */
|
|
if (td->error_any) {
|
|
/* the transfer is finished */
|
|
error = (td->error_stall ?
|
|
USB_ERR_STALLED : USB_ERR_IOERROR);
|
|
td = NULL;
|
|
break;
|
|
}
|
|
/* Check for short transfer */
|
|
if (len > 0) {
|
|
if (xfer->flags_int.short_frames_ok) {
|
|
/* follow alt next */
|
|
if (td->alt_next) {
|
|
td = td->obj_next;
|
|
} else {
|
|
td = NULL;
|
|
}
|
|
} else {
|
|
/* the transfer is finished */
|
|
td = NULL;
|
|
}
|
|
error = 0;
|
|
break;
|
|
}
|
|
td = td->obj_next;
|
|
|
|
/* this USB frame is complete */
|
|
error = 0;
|
|
break;
|
|
|
|
} while (0);
|
|
|
|
/* update transfer cache */
|
|
|
|
xfer->td_transfer_cache = td;
|
|
|
|
return (error);
|
|
}
|
|
|
|
static void
|
|
saf1761_otg_standard_done(struct usb_xfer *xfer)
|
|
{
|
|
usb_error_t err = 0;
|
|
|
|
DPRINTFN(13, "xfer=%p endpoint=%p transfer done\n",
|
|
xfer, xfer->endpoint);
|
|
|
|
/* reset scanner */
|
|
|
|
xfer->td_transfer_cache = xfer->td_transfer_first;
|
|
|
|
if (xfer->flags_int.control_xfr) {
|
|
|
|
if (xfer->flags_int.control_hdr) {
|
|
|
|
err = saf1761_otg_standard_done_sub(xfer);
|
|
}
|
|
xfer->aframes = 1;
|
|
|
|
if (xfer->td_transfer_cache == NULL) {
|
|
goto done;
|
|
}
|
|
}
|
|
while (xfer->aframes != xfer->nframes) {
|
|
|
|
err = saf1761_otg_standard_done_sub(xfer);
|
|
xfer->aframes++;
|
|
|
|
if (xfer->td_transfer_cache == NULL) {
|
|
goto done;
|
|
}
|
|
}
|
|
|
|
if (xfer->flags_int.control_xfr &&
|
|
!xfer->flags_int.control_act) {
|
|
|
|
err = saf1761_otg_standard_done_sub(xfer);
|
|
}
|
|
done:
|
|
saf1761_otg_device_done(xfer, err);
|
|
}
|
|
|
|
/*------------------------------------------------------------------------*
|
|
* saf1761_otg_device_done
|
|
*
|
|
* NOTE: this function can be called more than one time on the
|
|
* same USB transfer!
|
|
*------------------------------------------------------------------------*/
|
|
static void
|
|
saf1761_otg_device_done(struct usb_xfer *xfer, usb_error_t error)
|
|
{
|
|
struct saf1761_otg_softc *sc = SAF1761_OTG_BUS2SC(xfer->xroot->bus);
|
|
|
|
USB_BUS_LOCK_ASSERT(xfer->xroot->bus, MA_OWNED);
|
|
|
|
DPRINTFN(2, "xfer=%p, endpoint=%p, error=%d\n",
|
|
xfer, xfer->endpoint, error);
|
|
|
|
if (xfer->flags_int.usb_mode == USB_MODE_DEVICE) {
|
|
saf1761_otg_intr_set(xfer, 0);
|
|
} else {
|
|
struct saf1761_otg_td *td;
|
|
|
|
td = xfer->td_transfer_first;
|
|
|
|
if (td != NULL)
|
|
saf1761_host_channel_free(sc, td);
|
|
}
|
|
|
|
/* dequeue transfer and start next transfer */
|
|
usbd_transfer_done(xfer, error);
|
|
}
|
|
|
|
static void
|
|
saf1761_otg_xfer_stall(struct usb_xfer *xfer)
|
|
{
|
|
saf1761_otg_device_done(xfer, USB_ERR_STALLED);
|
|
}
|
|
|
|
static void
|
|
saf1761_otg_set_stall(struct usb_device *udev,
|
|
struct usb_endpoint *ep, uint8_t *did_stall)
|
|
{
|
|
struct saf1761_otg_softc *sc;
|
|
uint8_t ep_no;
|
|
uint8_t ep_type;
|
|
uint8_t ep_dir;
|
|
|
|
USB_BUS_LOCK_ASSERT(udev->bus, MA_OWNED);
|
|
|
|
/* check mode */
|
|
if (udev->flags.usb_mode != USB_MODE_DEVICE) {
|
|
/* not supported */
|
|
return;
|
|
}
|
|
|
|
DPRINTFN(5, "endpoint=%p\n", ep);
|
|
|
|
/* set FORCESTALL */
|
|
sc = SAF1761_OTG_BUS2SC(udev->bus);
|
|
ep_no = (ep->edesc->bEndpointAddress & UE_ADDR);
|
|
ep_dir = (ep->edesc->bEndpointAddress & (UE_DIR_IN | UE_DIR_OUT));
|
|
ep_type = (ep->edesc->bmAttributes & UE_XFERTYPE);
|
|
|
|
if (ep_type == UE_CONTROL) {
|
|
/* should not happen */
|
|
return;
|
|
}
|
|
/* select the correct endpoint */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_EP_INDEX,
|
|
(ep_no << SOTG_EP_INDEX_ENDP_INDEX_SHIFT) |
|
|
((ep_dir == UE_DIR_IN) ? SOTG_EP_INDEX_DIR_IN :
|
|
SOTG_EP_INDEX_DIR_OUT));
|
|
|
|
/* set stall */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_CTRL_FUNC, SOTG_CTRL_FUNC_STALL);
|
|
}
|
|
|
|
static void
|
|
saf1761_otg_clear_stall_sub(struct saf1761_otg_softc *sc,
|
|
uint8_t ep_no, uint8_t ep_type, uint8_t ep_dir)
|
|
{
|
|
if (ep_type == UE_CONTROL) {
|
|
/* clearing stall is not needed */
|
|
return;
|
|
}
|
|
/* select the correct endpoint */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_EP_INDEX,
|
|
(ep_no << SOTG_EP_INDEX_ENDP_INDEX_SHIFT) |
|
|
((ep_dir == UE_DIR_IN) ? SOTG_EP_INDEX_DIR_IN :
|
|
SOTG_EP_INDEX_DIR_OUT));
|
|
|
|
/* disable endpoint */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_EP_TYPE, 0);
|
|
/* enable endpoint again - will clear data toggle */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_EP_TYPE, ep_type | SOTG_EP_TYPE_ENABLE);
|
|
|
|
/* clear buffer */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_CTRL_FUNC, SOTG_CTRL_FUNC_CLBUF);
|
|
/* clear stall */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_CTRL_FUNC, 0);
|
|
}
|
|
|
|
static void
|
|
saf1761_otg_clear_stall(struct usb_device *udev, struct usb_endpoint *ep)
|
|
{
|
|
struct saf1761_otg_softc *sc;
|
|
struct usb_endpoint_descriptor *ed;
|
|
|
|
USB_BUS_LOCK_ASSERT(udev->bus, MA_OWNED);
|
|
|
|
DPRINTFN(5, "endpoint=%p\n", ep);
|
|
|
|
/* check mode */
|
|
if (udev->flags.usb_mode != USB_MODE_DEVICE) {
|
|
/* not supported */
|
|
return;
|
|
}
|
|
/* get softc */
|
|
sc = SAF1761_OTG_BUS2SC(udev->bus);
|
|
|
|
/* get endpoint descriptor */
|
|
ed = ep->edesc;
|
|
|
|
/* reset endpoint */
|
|
saf1761_otg_clear_stall_sub(sc,
|
|
(ed->bEndpointAddress & UE_ADDR),
|
|
(ed->bmAttributes & UE_XFERTYPE),
|
|
(ed->bEndpointAddress & (UE_DIR_IN | UE_DIR_OUT)));
|
|
}
|
|
|
|
usb_error_t
|
|
saf1761_otg_init(struct saf1761_otg_softc *sc)
|
|
{
|
|
const struct usb_hw_ep_profile *pf;
|
|
uint32_t x;
|
|
|
|
DPRINTF("\n");
|
|
|
|
/* set up the bus structure */
|
|
sc->sc_bus.usbrev = USB_REV_2_0;
|
|
sc->sc_bus.methods = &saf1761_otg_bus_methods;
|
|
|
|
USB_BUS_LOCK(&sc->sc_bus);
|
|
|
|
/* Reset Host controller, including HW mode */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_SW_RESET, SOTG_SW_RESET_ALL);
|
|
|
|
DELAY(1000);
|
|
|
|
/* Reset Host controller, including HW mode */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_SW_RESET, SOTG_SW_RESET_HC);
|
|
|
|
/* wait a bit */
|
|
DELAY(1000);
|
|
|
|
SAF1761_WRITE_LE_4(sc, SOTG_SW_RESET, 0);
|
|
|
|
/* wait a bit */
|
|
DELAY(1000);
|
|
|
|
/* Enable interrupts */
|
|
sc->sc_hw_mode |= SOTG_HW_MODE_CTRL_GLOBAL_INTR_EN |
|
|
SOTG_HW_MODE_CTRL_COMN_INT;
|
|
|
|
/* unlock device */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_UNLOCK_DEVICE, SOTG_UNLOCK_DEVICE_CODE);
|
|
|
|
/*
|
|
* Set correct hardware mode, must be written twice if bus
|
|
* width is changed:
|
|
*/
|
|
SAF1761_WRITE_LE_4(sc, SOTG_HW_MODE_CTRL, sc->sc_hw_mode);
|
|
SAF1761_WRITE_LE_4(sc, SOTG_HW_MODE_CTRL, sc->sc_hw_mode);
|
|
|
|
SAF1761_WRITE_LE_4(sc, SOTG_DCSCRATCH, 0xdeadbeef);
|
|
SAF1761_WRITE_LE_4(sc, SOTG_HCSCRATCH, 0xdeadbeef);
|
|
|
|
DPRINTF("DCID=0x%08x VEND_PROD=0x%08x HWMODE=0x%08x SCRATCH=0x%08x,0x%08x\n",
|
|
SAF1761_READ_LE_4(sc, SOTG_DCCHIP_ID),
|
|
SAF1761_READ_LE_4(sc, SOTG_VEND_PROD_ID),
|
|
SAF1761_READ_LE_4(sc, SOTG_HW_MODE_CTRL),
|
|
SAF1761_READ_LE_4(sc, SOTG_DCSCRATCH),
|
|
SAF1761_READ_LE_4(sc, SOTG_HCSCRATCH));
|
|
|
|
/* reset device controller */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_MODE, SOTG_MODE_SFRESET);
|
|
SAF1761_WRITE_LE_4(sc, SOTG_MODE, 0);
|
|
|
|
/* wait a bit */
|
|
DELAY(1000);
|
|
|
|
/* reset host controller */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_USBCMD, SOTG_USBCMD_HCRESET);
|
|
|
|
/* wait for reset to clear */
|
|
for (x = 0; x != 10; x++) {
|
|
if ((SAF1761_READ_LE_4(sc, SOTG_USBCMD) & SOTG_USBCMD_HCRESET) == 0)
|
|
break;
|
|
usb_pause_mtx(&sc->sc_bus.bus_mtx, hz / 10);
|
|
}
|
|
|
|
SAF1761_WRITE_LE_4(sc, SOTG_HW_MODE_CTRL, sc->sc_hw_mode |
|
|
SOTG_HW_MODE_CTRL_ALL_ATX_RESET);
|
|
|
|
/* wait a bit */
|
|
DELAY(1000);
|
|
|
|
SAF1761_WRITE_LE_4(sc, SOTG_HW_MODE_CTRL, sc->sc_hw_mode);
|
|
|
|
/* wait a bit */
|
|
DELAY(1000);
|
|
|
|
/* do a pulldown */
|
|
saf1761_otg_pull_down(sc);
|
|
|
|
/* wait 10ms for pulldown to stabilise */
|
|
usb_pause_mtx(&sc->sc_bus.bus_mtx, hz / 100);
|
|
|
|
for (x = 1;; x++) {
|
|
|
|
saf1761_otg_get_hw_ep_profile(NULL, &pf, x);
|
|
if (pf == NULL)
|
|
break;
|
|
|
|
/* select the correct endpoint */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_EP_INDEX,
|
|
(x << SOTG_EP_INDEX_ENDP_INDEX_SHIFT) |
|
|
SOTG_EP_INDEX_DIR_IN);
|
|
|
|
/* select the maximum packet size */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_EP_MAXPACKET, pf->max_in_frame_size);
|
|
|
|
/* select the correct endpoint */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_EP_INDEX,
|
|
(x << SOTG_EP_INDEX_ENDP_INDEX_SHIFT) |
|
|
SOTG_EP_INDEX_DIR_OUT);
|
|
|
|
/* select the maximum packet size */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_EP_MAXPACKET, pf->max_out_frame_size);
|
|
}
|
|
|
|
/* enable interrupts */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_MODE, SOTG_MODE_GLINTENA |
|
|
SOTG_MODE_CLKAON | SOTG_MODE_WKUPCS);
|
|
|
|
/* set default values */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_INTERRUPT_CFG,
|
|
SOTG_INTERRUPT_CFG_CDBGMOD |
|
|
SOTG_INTERRUPT_CFG_DDBGMODIN |
|
|
SOTG_INTERRUPT_CFG_DDBGMODOUT);
|
|
|
|
/* enable VBUS and ID interrupt */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_IRQ_ENABLE_SET_CLR,
|
|
SOTG_IRQ_ENABLE_CLR(0xFFFF));
|
|
SAF1761_WRITE_LE_4(sc, SOTG_IRQ_ENABLE_SET_CLR,
|
|
SOTG_IRQ_ENABLE_SET(SOTG_IRQ_ID | SOTG_IRQ_VBUS_VLD));
|
|
|
|
/* enable interrupts */
|
|
sc->sc_intr_enable = SOTG_DCINTERRUPT_IEVBUS |
|
|
SOTG_DCINTERRUPT_IEBRST | SOTG_DCINTERRUPT_IESUSP;
|
|
SAF1761_WRITE_LE_4(sc, SOTG_DCINTERRUPT_EN, sc->sc_intr_enable);
|
|
|
|
/*
|
|
* Connect ATX port 1 to device controller, select external
|
|
* charge pump and driver VBUS to +5V:
|
|
*/
|
|
SAF1761_WRITE_LE_4(sc, SOTG_CTRL_SET_CLR,
|
|
SOTG_CTRL_CLR(0xFFFF));
|
|
SAF1761_WRITE_LE_4(sc, SOTG_CTRL_SET_CLR,
|
|
SOTG_CTRL_SET(SOTG_CTRL_SW_SEL_HC_DC |
|
|
SOTG_CTRL_BDIS_ACON_EN | SOTG_CTRL_SEL_CP_EXT |
|
|
SOTG_CTRL_VBUS_DRV));
|
|
|
|
/* disable device address */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_ADDRESS, 0);
|
|
|
|
/* enable host controller clock and preserve reserved bits */
|
|
x = SAF1761_READ_LE_4(sc, SOTG_POWER_DOWN);
|
|
SAF1761_WRITE_LE_4(sc, SOTG_POWER_DOWN, x | SOTG_POWER_DOWN_HC_CLK_EN);
|
|
|
|
/* wait 10ms for clock */
|
|
usb_pause_mtx(&sc->sc_bus.bus_mtx, hz / 100);
|
|
|
|
/* enable configuration flag */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_CONFIGFLAG, SOTG_CONFIGFLAG_ENABLE);
|
|
|
|
/* clear RAM block */
|
|
for (x = 0x400; x != 0x10000; x += 4)
|
|
SAF1761_WRITE_LE_4(sc, x, 0);
|
|
|
|
/* start the HC */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_USBCMD, SOTG_USBCMD_RS);
|
|
|
|
DPRINTF("USBCMD=0x%08x\n", SAF1761_READ_LE_4(sc, SOTG_USBCMD));
|
|
|
|
/* activate all PTDs */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_ATL_PTD_LAST_PTD, (1 << 31));
|
|
SAF1761_WRITE_LE_4(sc, SOTG_INT_PTD_LAST_PTD, (1 << 31));
|
|
SAF1761_WRITE_LE_4(sc, SOTG_ISO_PTD_LAST_PTD, (1 << 31));
|
|
|
|
/* skip no PTDs */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_ATL_PTD_SKIP_PTD, 0);
|
|
SAF1761_WRITE_LE_4(sc, SOTG_INT_PTD_SKIP_PTD, 0);
|
|
SAF1761_WRITE_LE_4(sc, SOTG_ISO_PTD_SKIP_PTD, 0);
|
|
|
|
/* activate all PTD types */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_HCBUFFERSTATUS,
|
|
SOTG_HCBUFFERSTATUS_ISO_BUF_FILL |
|
|
SOTG_HCBUFFERSTATUS_INT_BUF_FILL |
|
|
SOTG_HCBUFFERSTATUS_ATL_BUF_FILL);
|
|
|
|
/* enable HC interrupts */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_HCINTERRUPT_ENABLE,
|
|
SOTG_HCINTERRUPT_OTG_IRQ |
|
|
SOTG_HCINTERRUPT_ISO_IRQ |
|
|
SOTG_HCINTERRUPT_ALT_IRQ |
|
|
SOTG_HCINTERRUPT_INT_IRQ);
|
|
|
|
/* poll initial VBUS status */
|
|
saf1761_otg_update_vbus(sc);
|
|
|
|
USB_BUS_UNLOCK(&sc->sc_bus);
|
|
|
|
/* catch any lost interrupts */
|
|
|
|
saf1761_otg_do_poll(&sc->sc_bus);
|
|
|
|
return (0); /* success */
|
|
}
|
|
|
|
void
|
|
saf1761_otg_uninit(struct saf1761_otg_softc *sc)
|
|
{
|
|
USB_BUS_LOCK(&sc->sc_bus);
|
|
|
|
/* disable all interrupts */
|
|
SAF1761_WRITE_LE_4(sc, SOTG_MODE, 0);
|
|
|
|
sc->sc_flags.port_powered = 0;
|
|
sc->sc_flags.status_vbus = 0;
|
|
sc->sc_flags.status_bus_reset = 0;
|
|
sc->sc_flags.status_suspend = 0;
|
|
sc->sc_flags.change_suspend = 0;
|
|
sc->sc_flags.change_connect = 1;
|
|
|
|
saf1761_otg_pull_down(sc);
|
|
USB_BUS_UNLOCK(&sc->sc_bus);
|
|
}
|
|
|
|
static void
|
|
saf1761_otg_suspend(struct saf1761_otg_softc *sc)
|
|
{
|
|
/* TODO */
|
|
}
|
|
|
|
static void
|
|
saf1761_otg_resume(struct saf1761_otg_softc *sc)
|
|
{
|
|
/* TODO */
|
|
}
|
|
|
|
static void
|
|
saf1761_otg_do_poll(struct usb_bus *bus)
|
|
{
|
|
struct saf1761_otg_softc *sc = SAF1761_OTG_BUS2SC(bus);
|
|
|
|
USB_BUS_LOCK(&sc->sc_bus);
|
|
saf1761_otg_interrupt_poll(sc);
|
|
USB_BUS_UNLOCK(&sc->sc_bus);
|
|
}
|
|
|
|
/*------------------------------------------------------------------------*
|
|
* saf1761_otg control support
|
|
* saf1761_otg interrupt support
|
|
* saf1761_otg bulk support
|
|
*------------------------------------------------------------------------*/
|
|
static void
|
|
saf1761_otg_device_non_isoc_open(struct usb_xfer *xfer)
|
|
{
|
|
return;
|
|
}
|
|
|
|
static void
|
|
saf1761_otg_device_non_isoc_close(struct usb_xfer *xfer)
|
|
{
|
|
saf1761_otg_device_done(xfer, USB_ERR_CANCELLED);
|
|
}
|
|
|
|
static void
|
|
saf1761_otg_device_non_isoc_enter(struct usb_xfer *xfer)
|
|
{
|
|
return;
|
|
}
|
|
|
|
static void
|
|
saf1761_otg_device_non_isoc_start(struct usb_xfer *xfer)
|
|
{
|
|
/* setup TDs */
|
|
saf1761_otg_setup_standard_chain(xfer);
|
|
saf1761_otg_start_standard_chain(xfer);
|
|
}
|
|
|
|
static const struct usb_pipe_methods saf1761_otg_non_isoc_methods =
|
|
{
|
|
.open = saf1761_otg_device_non_isoc_open,
|
|
.close = saf1761_otg_device_non_isoc_close,
|
|
.enter = saf1761_otg_device_non_isoc_enter,
|
|
.start = saf1761_otg_device_non_isoc_start,
|
|
};
|
|
|
|
/*------------------------------------------------------------------------*
|
|
* saf1761_otg isochronous support
|
|
*------------------------------------------------------------------------*/
|
|
static void
|
|
saf1761_otg_device_isoc_open(struct usb_xfer *xfer)
|
|
{
|
|
return;
|
|
}
|
|
|
|
static void
|
|
saf1761_otg_device_isoc_close(struct usb_xfer *xfer)
|
|
{
|
|
saf1761_otg_device_done(xfer, USB_ERR_CANCELLED);
|
|
}
|
|
|
|
static void
|
|
saf1761_otg_device_isoc_enter(struct usb_xfer *xfer)
|
|
{
|
|
struct saf1761_otg_softc *sc = SAF1761_OTG_BUS2SC(xfer->xroot->bus);
|
|
uint32_t temp;
|
|
uint32_t nframes;
|
|
|
|
DPRINTFN(6, "xfer=%p next=%d nframes=%d\n",
|
|
xfer, xfer->endpoint->isoc_next, xfer->nframes);
|
|
|
|
/* get the current frame index - we don't need the high bits */
|
|
|
|
nframes = SAF1761_READ_LE_4(sc, SOTG_FRAME_NUM);
|
|
|
|
/*
|
|
* check if the frame index is within the window where the
|
|
* frames will be inserted
|
|
*/
|
|
temp = (nframes - xfer->endpoint->isoc_next) & SOTG_FRAME_NUM_SOFR_MASK;
|
|
|
|
if ((xfer->endpoint->is_synced == 0) ||
|
|
(temp < xfer->nframes)) {
|
|
/*
|
|
* If there is data underflow or the pipe queue is
|
|
* empty we schedule the transfer a few frames ahead
|
|
* of the current frame position. Else two isochronous
|
|
* transfers might overlap.
|
|
*/
|
|
xfer->endpoint->isoc_next = (nframes + 3) & SOTG_FRAME_NUM_SOFR_MASK;
|
|
xfer->endpoint->is_synced = 1;
|
|
DPRINTFN(3, "start next=%d\n", xfer->endpoint->isoc_next);
|
|
}
|
|
/*
|
|
* compute how many milliseconds the insertion is ahead of the
|
|
* current frame position:
|
|
*/
|
|
temp = (xfer->endpoint->isoc_next - nframes) & SOTG_FRAME_NUM_SOFR_MASK;
|
|
|
|
/*
|
|
* pre-compute when the isochronous transfer will be finished:
|
|
*/
|
|
xfer->isoc_time_complete =
|
|
usb_isoc_time_expand(&sc->sc_bus, nframes) + temp +
|
|
xfer->nframes;
|
|
|
|
/* compute frame number for next insertion */
|
|
xfer->endpoint->isoc_next += xfer->nframes;
|
|
|
|
/* setup TDs */
|
|
saf1761_otg_setup_standard_chain(xfer);
|
|
}
|
|
|
|
static void
|
|
saf1761_otg_device_isoc_start(struct usb_xfer *xfer)
|
|
{
|
|
/* start TD chain */
|
|
saf1761_otg_start_standard_chain(xfer);
|
|
}
|
|
|
|
static const struct usb_pipe_methods saf1761_otg_device_isoc_methods =
|
|
{
|
|
.open = saf1761_otg_device_isoc_open,
|
|
.close = saf1761_otg_device_isoc_close,
|
|
.enter = saf1761_otg_device_isoc_enter,
|
|
.start = saf1761_otg_device_isoc_start,
|
|
};
|
|
|
|
/*------------------------------------------------------------------------*
|
|
* saf1761_otg root control support
|
|
*------------------------------------------------------------------------*
|
|
* Simulate a hardware HUB by handling all the necessary requests.
|
|
*------------------------------------------------------------------------*/
|
|
|
|
#define HSETW(ptr, val) ptr = { (uint8_t)(val), (uint8_t)((val) >> 8) }
|
|
|
|
static const struct usb_device_descriptor saf1761_otg_devd = {
|
|
.bLength = sizeof(struct usb_device_descriptor),
|
|
.bDescriptorType = UDESC_DEVICE,
|
|
HSETW(.idVendor, 0x04cc),
|
|
HSETW(.idProduct, 0x1761),
|
|
.bcdUSB = {0x00, 0x02},
|
|
.bDeviceClass = UDCLASS_HUB,
|
|
.bDeviceSubClass = UDSUBCLASS_HUB,
|
|
.bDeviceProtocol = UDPROTO_FSHUB,
|
|
.bMaxPacketSize = 64,
|
|
.bcdDevice = {0x00, 0x01},
|
|
.iManufacturer = 1,
|
|
.iProduct = 2,
|
|
.bNumConfigurations = 1,
|
|
};
|
|
|
|
static const struct usb_device_qualifier saf1761_otg_odevd = {
|
|
.bLength = sizeof(struct usb_device_qualifier),
|
|
.bDescriptorType = UDESC_DEVICE_QUALIFIER,
|
|
.bcdUSB = {0x00, 0x02},
|
|
.bDeviceClass = UDCLASS_HUB,
|
|
.bDeviceSubClass = UDSUBCLASS_HUB,
|
|
.bDeviceProtocol = UDPROTO_FSHUB,
|
|
.bMaxPacketSize0 = 0,
|
|
.bNumConfigurations = 0,
|
|
};
|
|
|
|
static const struct saf1761_otg_config_desc saf1761_otg_confd = {
|
|
.confd = {
|
|
.bLength = sizeof(struct usb_config_descriptor),
|
|
.bDescriptorType = UDESC_CONFIG,
|
|
.wTotalLength[0] = sizeof(saf1761_otg_confd),
|
|
.bNumInterface = 1,
|
|
.bConfigurationValue = 1,
|
|
.iConfiguration = 0,
|
|
.bmAttributes = UC_SELF_POWERED,
|
|
.bMaxPower = 0,
|
|
},
|
|
.ifcd = {
|
|
.bLength = sizeof(struct usb_interface_descriptor),
|
|
.bDescriptorType = UDESC_INTERFACE,
|
|
.bNumEndpoints = 1,
|
|
.bInterfaceClass = UICLASS_HUB,
|
|
.bInterfaceSubClass = UISUBCLASS_HUB,
|
|
.bInterfaceProtocol = 0,
|
|
},
|
|
|
|
.endpd = {
|
|
.bLength = sizeof(struct usb_endpoint_descriptor),
|
|
.bDescriptorType = UDESC_ENDPOINT,
|
|
.bEndpointAddress = (UE_DIR_IN | SAF1761_OTG_INTR_ENDPT),
|
|
.bmAttributes = UE_INTERRUPT,
|
|
.wMaxPacketSize[0] = 8,
|
|
.bInterval = 255,
|
|
},
|
|
};
|
|
|
|
static const struct usb_hub_descriptor_min saf1761_otg_hubd = {
|
|
.bDescLength = sizeof(saf1761_otg_hubd),
|
|
.bDescriptorType = UDESC_HUB,
|
|
.bNbrPorts = SOTG_NUM_PORTS,
|
|
HSETW(.wHubCharacteristics, (UHD_PWR_NO_SWITCH | UHD_OC_INDIVIDUAL)),
|
|
.bPwrOn2PwrGood = 50,
|
|
.bHubContrCurrent = 0,
|
|
.DeviceRemovable = {0}, /* port is removable */
|
|
};
|
|
|
|
#define STRING_VENDOR \
|
|
"N\0X\0P"
|
|
|
|
#define STRING_PRODUCT \
|
|
"D\0C\0I\0 \0R\0o\0o\0t\0 \0H\0U\0B"
|
|
|
|
USB_MAKE_STRING_DESC(STRING_VENDOR, saf1761_otg_vendor);
|
|
USB_MAKE_STRING_DESC(STRING_PRODUCT, saf1761_otg_product);
|
|
|
|
static usb_error_t
|
|
saf1761_otg_roothub_exec(struct usb_device *udev,
|
|
struct usb_device_request *req, const void **pptr, uint16_t *plength)
|
|
{
|
|
struct saf1761_otg_softc *sc = SAF1761_OTG_BUS2SC(udev->bus);
|
|
const void *ptr;
|
|
uint16_t len;
|
|
uint16_t value;
|
|
uint16_t index;
|
|
uint32_t temp;
|
|
uint32_t i;
|
|
usb_error_t err;
|
|
|
|
USB_BUS_LOCK_ASSERT(&sc->sc_bus, MA_OWNED);
|
|
|
|
/* buffer reset */
|
|
ptr = (const void *)&sc->sc_hub_temp;
|
|
len = 0;
|
|
err = 0;
|
|
|
|
value = UGETW(req->wValue);
|
|
index = UGETW(req->wIndex);
|
|
|
|
/* demultiplex the control request */
|
|
|
|
switch (req->bmRequestType) {
|
|
case UT_READ_DEVICE:
|
|
switch (req->bRequest) {
|
|
case UR_GET_DESCRIPTOR:
|
|
goto tr_handle_get_descriptor;
|
|
case UR_GET_CONFIG:
|
|
goto tr_handle_get_config;
|
|
case UR_GET_STATUS:
|
|
goto tr_handle_get_status;
|
|
default:
|
|
goto tr_stalled;
|
|
}
|
|
break;
|
|
|
|
case UT_WRITE_DEVICE:
|
|
switch (req->bRequest) {
|
|
case UR_SET_ADDRESS:
|
|
goto tr_handle_set_address;
|
|
case UR_SET_CONFIG:
|
|
goto tr_handle_set_config;
|
|
case UR_CLEAR_FEATURE:
|
|
goto tr_valid; /* nop */
|
|
case UR_SET_DESCRIPTOR:
|
|
goto tr_valid; /* nop */
|
|
case UR_SET_FEATURE:
|
|
default:
|
|
goto tr_stalled;
|
|
}
|
|
break;
|
|
|
|
case UT_WRITE_ENDPOINT:
|
|
switch (req->bRequest) {
|
|
case UR_CLEAR_FEATURE:
|
|
switch (UGETW(req->wValue)) {
|
|
case UF_ENDPOINT_HALT:
|
|
goto tr_handle_clear_halt;
|
|
case UF_DEVICE_REMOTE_WAKEUP:
|
|
goto tr_handle_clear_wakeup;
|
|
default:
|
|
goto tr_stalled;
|
|
}
|
|
break;
|
|
case UR_SET_FEATURE:
|
|
switch (UGETW(req->wValue)) {
|
|
case UF_ENDPOINT_HALT:
|
|
goto tr_handle_set_halt;
|
|
case UF_DEVICE_REMOTE_WAKEUP:
|
|
goto tr_handle_set_wakeup;
|
|
default:
|
|
goto tr_stalled;
|
|
}
|
|
break;
|
|
case UR_SYNCH_FRAME:
|
|
goto tr_valid; /* nop */
|
|
default:
|
|
goto tr_stalled;
|
|
}
|
|
break;
|
|
|
|
case UT_READ_ENDPOINT:
|
|
switch (req->bRequest) {
|
|
case UR_GET_STATUS:
|
|
goto tr_handle_get_ep_status;
|
|
default:
|
|
goto tr_stalled;
|
|
}
|
|
break;
|
|
|
|
case UT_WRITE_INTERFACE:
|
|
switch (req->bRequest) {
|
|
case UR_SET_INTERFACE:
|
|
goto tr_handle_set_interface;
|
|
case UR_CLEAR_FEATURE:
|
|
goto tr_valid; /* nop */
|
|
case UR_SET_FEATURE:
|
|
default:
|
|
goto tr_stalled;
|
|
}
|
|
break;
|
|
|
|
case UT_READ_INTERFACE:
|
|
switch (req->bRequest) {
|
|
case UR_GET_INTERFACE:
|
|
goto tr_handle_get_interface;
|
|
case UR_GET_STATUS:
|
|
goto tr_handle_get_iface_status;
|
|
default:
|
|
goto tr_stalled;
|
|
}
|
|
break;
|
|
|
|
case UT_WRITE_CLASS_INTERFACE:
|
|
case UT_WRITE_VENDOR_INTERFACE:
|
|
/* XXX forward */
|
|
break;
|
|
|
|
case UT_READ_CLASS_INTERFACE:
|
|
case UT_READ_VENDOR_INTERFACE:
|
|
/* XXX forward */
|
|
break;
|
|
|
|
case UT_WRITE_CLASS_DEVICE:
|
|
switch (req->bRequest) {
|
|
case UR_CLEAR_FEATURE:
|
|
goto tr_valid;
|
|
case UR_SET_DESCRIPTOR:
|
|
case UR_SET_FEATURE:
|
|
break;
|
|
default:
|
|
goto tr_stalled;
|
|
}
|
|
break;
|
|
|
|
case UT_WRITE_CLASS_OTHER:
|
|
switch (req->bRequest) {
|
|
case UR_CLEAR_FEATURE:
|
|
if (index == SOTG_HOST_PORT_NUM)
|
|
goto tr_handle_clear_port_feature_host;
|
|
else if (index == SOTG_DEVICE_PORT_NUM)
|
|
goto tr_handle_clear_port_feature_device;
|
|
else
|
|
goto tr_stalled;
|
|
case UR_SET_FEATURE:
|
|
if (index == SOTG_HOST_PORT_NUM)
|
|
goto tr_handle_set_port_feature_host;
|
|
else if (index == SOTG_DEVICE_PORT_NUM)
|
|
goto tr_handle_set_port_feature_device;
|
|
else
|
|
goto tr_stalled;
|
|
case UR_CLEAR_TT_BUFFER:
|
|
case UR_RESET_TT:
|
|
case UR_STOP_TT:
|
|
goto tr_valid;
|
|
|
|
default:
|
|
goto tr_stalled;
|
|
}
|
|
break;
|
|
|
|
case UT_READ_CLASS_OTHER:
|
|
switch (req->bRequest) {
|
|
case UR_GET_TT_STATE:
|
|
goto tr_handle_get_tt_state;
|
|
case UR_GET_STATUS:
|
|
if (index == SOTG_HOST_PORT_NUM)
|
|
goto tr_handle_get_port_status_host;
|
|
else if (index == SOTG_DEVICE_PORT_NUM)
|
|
goto tr_handle_get_port_status_device;
|
|
else
|
|
goto tr_stalled;
|
|
default:
|
|
goto tr_stalled;
|
|
}
|
|
break;
|
|
|
|
case UT_READ_CLASS_DEVICE:
|
|
switch (req->bRequest) {
|
|
case UR_GET_DESCRIPTOR:
|
|
goto tr_handle_get_class_descriptor;
|
|
case UR_GET_STATUS:
|
|
goto tr_handle_get_class_status;
|
|
|
|
default:
|
|
goto tr_stalled;
|
|
}
|
|
break;
|
|
default:
|
|
goto tr_stalled;
|
|
}
|
|
goto tr_valid;
|
|
|
|
tr_handle_get_descriptor:
|
|
switch (value >> 8) {
|
|
case UDESC_DEVICE:
|
|
if (value & 0xff)
|
|
goto tr_stalled;
|
|
len = sizeof(saf1761_otg_devd);
|
|
ptr = (const void *)&saf1761_otg_devd;
|
|
goto tr_valid;
|
|
case UDESC_DEVICE_QUALIFIER:
|
|
if (value & 0xff)
|
|
goto tr_stalled;
|
|
len = sizeof(saf1761_otg_odevd);
|
|
ptr = (const void *)&saf1761_otg_odevd;
|
|
goto tr_valid;
|
|
case UDESC_CONFIG:
|
|
if (value & 0xff)
|
|
goto tr_stalled;
|
|
len = sizeof(saf1761_otg_confd);
|
|
ptr = (const void *)&saf1761_otg_confd;
|
|
goto tr_valid;
|
|
case UDESC_STRING:
|
|
switch (value & 0xff) {
|
|
case 0: /* Language table */
|
|
len = sizeof(usb_string_lang_en);
|
|
ptr = (const void *)&usb_string_lang_en;
|
|
goto tr_valid;
|
|
|
|
case 1: /* Vendor */
|
|
len = sizeof(saf1761_otg_vendor);
|
|
ptr = (const void *)&saf1761_otg_vendor;
|
|
goto tr_valid;
|
|
|
|
case 2: /* Product */
|
|
len = sizeof(saf1761_otg_product);
|
|
ptr = (const void *)&saf1761_otg_product;
|
|
goto tr_valid;
|
|
default:
|
|
break;
|
|
}
|
|
break;
|
|
default:
|
|
goto tr_stalled;
|
|
}
|
|
goto tr_stalled;
|
|
|
|
tr_handle_get_config:
|
|
len = 1;
|
|
sc->sc_hub_temp.wValue[0] = sc->sc_conf;
|
|
goto tr_valid;
|
|
|
|
tr_handle_get_status:
|
|
len = 2;
|
|
USETW(sc->sc_hub_temp.wValue, UDS_SELF_POWERED);
|
|
goto tr_valid;
|
|
|
|
tr_handle_set_address:
|
|
if (value & 0xFF00)
|
|
goto tr_stalled;
|
|
|
|
sc->sc_rt_addr = value;
|
|
goto tr_valid;
|
|
|
|
tr_handle_set_config:
|
|
if (value >= 2)
|
|
goto tr_stalled;
|
|
sc->sc_conf = value;
|
|
goto tr_valid;
|
|
|
|
tr_handle_get_interface:
|
|
len = 1;
|
|
sc->sc_hub_temp.wValue[0] = 0;
|
|
goto tr_valid;
|
|
|
|
tr_handle_get_tt_state:
|
|
tr_handle_get_class_status:
|
|
tr_handle_get_iface_status:
|
|
tr_handle_get_ep_status:
|
|
len = 2;
|
|
USETW(sc->sc_hub_temp.wValue, 0);
|
|
goto tr_valid;
|
|
|
|
tr_handle_set_halt:
|
|
tr_handle_set_interface:
|
|
tr_handle_set_wakeup:
|
|
tr_handle_clear_wakeup:
|
|
tr_handle_clear_halt:
|
|
goto tr_valid;
|
|
|
|
tr_handle_clear_port_feature_device:
|
|
DPRINTFN(9, "UR_CLEAR_FEATURE on port %d\n", index);
|
|
|
|
switch (value) {
|
|
case UHF_PORT_SUSPEND:
|
|
saf1761_otg_wakeup_peer(sc);
|
|
break;
|
|
|
|
case UHF_PORT_ENABLE:
|
|
sc->sc_flags.port_enabled = 0;
|
|
break;
|
|
|
|
case UHF_PORT_TEST:
|
|
case UHF_PORT_INDICATOR:
|
|
case UHF_C_PORT_ENABLE:
|
|
case UHF_C_PORT_OVER_CURRENT:
|
|
case UHF_C_PORT_RESET:
|
|
/* nops */
|
|
break;
|
|
case UHF_PORT_POWER:
|
|
sc->sc_flags.port_powered = 0;
|
|
saf1761_otg_pull_down(sc);
|
|
break;
|
|
case UHF_C_PORT_CONNECTION:
|
|
sc->sc_flags.change_connect = 0;
|
|
break;
|
|
case UHF_C_PORT_SUSPEND:
|
|
sc->sc_flags.change_suspend = 0;
|
|
break;
|
|
default:
|
|
err = USB_ERR_IOERROR;
|
|
goto tr_valid;
|
|
}
|
|
goto tr_valid;
|
|
|
|
tr_handle_clear_port_feature_host:
|
|
DPRINTFN(9, "UR_CLEAR_FEATURE on port %d\n", index);
|
|
|
|
temp = SAF1761_READ_LE_4(sc, SOTG_PORTSC1);
|
|
|
|
switch (value) {
|
|
case UHF_PORT_ENABLE:
|
|
SAF1761_WRITE_LE_4(sc, SOTG_PORTSC1, temp & ~SOTG_PORTSC1_PED);
|
|
break;
|
|
case UHF_PORT_SUSPEND:
|
|
if ((temp & SOTG_PORTSC1_SUSP) && (!(temp & SOTG_PORTSC1_FPR)))
|
|
SAF1761_WRITE_LE_4(sc, SOTG_PORTSC1, temp | SOTG_PORTSC1_FPR);
|
|
|
|
/* wait 20ms for resume sequence to complete */
|
|
usb_pause_mtx(&sc->sc_bus.bus_mtx, hz / 50);
|
|
|
|
SAF1761_WRITE_LE_4(sc, SOTG_PORTSC1, temp & ~(SOTG_PORTSC1_SUSP |
|
|
SOTG_PORTSC1_FPR | SOTG_PORTSC1_LS /* High Speed */ ));
|
|
|
|
/* 4ms settle time */
|
|
usb_pause_mtx(&sc->sc_bus.bus_mtx, hz / 250);
|
|
break;
|
|
case UHF_PORT_INDICATOR:
|
|
SAF1761_WRITE_LE_4(sc, SOTG_PORTSC1, temp & ~SOTG_PORTSC1_PIC);
|
|
break;
|
|
case UHF_PORT_TEST:
|
|
case UHF_C_PORT_ENABLE:
|
|
case UHF_C_PORT_OVER_CURRENT:
|
|
case UHF_C_PORT_RESET:
|
|
case UHF_C_PORT_SUSPEND:
|
|
/* NOPs */
|
|
break;
|
|
case UHF_PORT_POWER:
|
|
SAF1761_WRITE_LE_4(sc, SOTG_PORTSC1, temp & ~SOTG_PORTSC1_PP);
|
|
break;
|
|
case UHF_C_PORT_CONNECTION:
|
|
SAF1761_WRITE_LE_4(sc, SOTG_PORTSC1, temp & ~SOTG_PORTSC1_ECSC);
|
|
break;
|
|
default:
|
|
err = USB_ERR_IOERROR;
|
|
goto tr_valid;
|
|
}
|
|
goto tr_valid;
|
|
|
|
tr_handle_set_port_feature_device:
|
|
DPRINTFN(9, "UR_SET_FEATURE on port %d\n", index);
|
|
|
|
switch (value) {
|
|
case UHF_PORT_ENABLE:
|
|
sc->sc_flags.port_enabled = 1;
|
|
break;
|
|
case UHF_PORT_SUSPEND:
|
|
case UHF_PORT_RESET:
|
|
case UHF_PORT_TEST:
|
|
case UHF_PORT_INDICATOR:
|
|
/* nops */
|
|
break;
|
|
case UHF_PORT_POWER:
|
|
sc->sc_flags.port_powered = 1;
|
|
break;
|
|
default:
|
|
err = USB_ERR_IOERROR;
|
|
goto tr_valid;
|
|
}
|
|
goto tr_valid;
|
|
|
|
tr_handle_set_port_feature_host:
|
|
DPRINTFN(9, "UR_SET_FEATURE on port %d\n", index);
|
|
|
|
temp = SAF1761_READ_LE_4(sc, SOTG_PORTSC1);
|
|
|
|
switch (value) {
|
|
case UHF_PORT_ENABLE:
|
|
SAF1761_WRITE_LE_4(sc, SOTG_PORTSC1, temp | SOTG_PORTSC1_PED);
|
|
break;
|
|
case UHF_PORT_SUSPEND:
|
|
SAF1761_WRITE_LE_4(sc, SOTG_PORTSC1, temp | SOTG_PORTSC1_SUSP);
|
|
break;
|
|
case UHF_PORT_RESET:
|
|
DPRINTFN(6, "reset port %d\n", index);
|
|
|
|
/* Start reset sequence. */
|
|
temp &= ~(SOTG_PORTSC1_PED | SOTG_PORTSC1_PR);
|
|
|
|
SAF1761_WRITE_LE_4(sc, SOTG_PORTSC1, temp | SOTG_PORTSC1_PR);
|
|
|
|
/* Wait for reset to complete. */
|
|
usb_pause_mtx(&sc->sc_bus.bus_mtx,
|
|
USB_MS_TO_TICKS(usb_port_root_reset_delay));
|
|
|
|
SAF1761_WRITE_LE_4(sc, SOTG_PORTSC1, temp);
|
|
|
|
/* Wait for HC to complete reset. */
|
|
usb_pause_mtx(&sc->sc_bus.bus_mtx, USB_MS_TO_TICKS(2));
|
|
|
|
temp = SAF1761_READ_LE_4(sc, SOTG_PORTSC1);
|
|
|
|
DPRINTF("After reset, status=0x%08x\n", temp);
|
|
if (temp & SOTG_PORTSC1_PR) {
|
|
device_printf(sc->sc_bus.bdev, "port reset timeout\n");
|
|
err = USB_ERR_TIMEOUT;
|
|
goto tr_valid;
|
|
}
|
|
if (!(temp & SOTG_PORTSC1_PED)) {
|
|
/* Not a high speed device, give up ownership.*/
|
|
SAF1761_WRITE_LE_4(sc, SOTG_PORTSC1, temp | SOTG_PORTSC1_PO);
|
|
break;
|
|
}
|
|
sc->sc_isreset = 1;
|
|
DPRINTF("port %d reset, status = 0x%08x\n", index, temp);
|
|
break;
|
|
case UHF_PORT_POWER:
|
|
DPRINTFN(3, "set port power %d\n", index);
|
|
SAF1761_WRITE_LE_4(sc, SOTG_PORTSC1, temp | SOTG_PORTSC1_PP);
|
|
break;
|
|
|
|
case UHF_PORT_TEST:
|
|
DPRINTFN(3, "set port test %d\n", index);
|
|
break;
|
|
|
|
case UHF_PORT_INDICATOR:
|
|
DPRINTFN(3, "set port ind %d\n", index);
|
|
SAF1761_WRITE_LE_4(sc, SOTG_PORTSC1, temp | SOTG_PORTSC1_PIC);
|
|
break;
|
|
default:
|
|
err = USB_ERR_IOERROR;
|
|
goto tr_valid;
|
|
}
|
|
goto tr_valid;
|
|
|
|
tr_handle_get_port_status_device:
|
|
|
|
DPRINTFN(9, "UR_GET_PORT_STATUS on port %d\n", index);
|
|
|
|
if (sc->sc_flags.status_vbus) {
|
|
saf1761_otg_pull_up(sc);
|
|
} else {
|
|
saf1761_otg_pull_down(sc);
|
|
}
|
|
|
|
/* Select FULL-speed and Device Side Mode */
|
|
|
|
value = UPS_PORT_MODE_DEVICE;
|
|
|
|
if (sc->sc_flags.port_powered)
|
|
value |= UPS_PORT_POWER;
|
|
|
|
if (sc->sc_flags.port_enabled)
|
|
value |= UPS_PORT_ENABLED;
|
|
|
|
if (sc->sc_flags.status_vbus &&
|
|
sc->sc_flags.status_bus_reset)
|
|
value |= UPS_CURRENT_CONNECT_STATUS;
|
|
|
|
if (sc->sc_flags.status_suspend)
|
|
value |= UPS_SUSPEND;
|
|
|
|
USETW(sc->sc_hub_temp.ps.wPortStatus, value);
|
|
|
|
value = 0;
|
|
|
|
if (sc->sc_flags.change_connect)
|
|
value |= UPS_C_CONNECT_STATUS;
|
|
|
|
if (sc->sc_flags.change_suspend)
|
|
value |= UPS_C_SUSPEND;
|
|
|
|
USETW(sc->sc_hub_temp.ps.wPortChange, value);
|
|
len = sizeof(sc->sc_hub_temp.ps);
|
|
goto tr_valid;
|
|
|
|
tr_handle_get_port_status_host:
|
|
|
|
temp = SAF1761_READ_LE_4(sc, SOTG_PORTSC1);
|
|
|
|
DPRINTFN(9, "UR_GET_PORT_STATUS on port %d = 0x%08x\n", index, temp);
|
|
|
|
i = UPS_HIGH_SPEED;
|
|
|
|
if (temp & SOTG_PORTSC1_ECCS)
|
|
i |= UPS_CURRENT_CONNECT_STATUS;
|
|
if (temp & SOTG_PORTSC1_PED)
|
|
i |= UPS_PORT_ENABLED;
|
|
if ((temp & SOTG_PORTSC1_SUSP) && !(temp & SOTG_PORTSC1_FPR))
|
|
i |= UPS_SUSPEND;
|
|
if (temp & SOTG_PORTSC1_PR)
|
|
i |= UPS_RESET;
|
|
if (temp & SOTG_PORTSC1_PP)
|
|
i |= UPS_PORT_POWER;
|
|
|
|
USETW(sc->sc_hub_temp.ps.wPortStatus, i);
|
|
i = 0;
|
|
|
|
if (temp & SOTG_PORTSC1_ECSC)
|
|
i |= UPS_C_CONNECT_STATUS;
|
|
if (temp & SOTG_PORTSC1_FPR)
|
|
i |= UPS_C_SUSPEND;
|
|
if (sc->sc_isreset)
|
|
i |= UPS_C_PORT_RESET;
|
|
USETW(sc->sc_hub_temp.ps.wPortChange, i);
|
|
len = sizeof(sc->sc_hub_temp.ps);
|
|
goto tr_valid;
|
|
|
|
tr_handle_get_class_descriptor:
|
|
if (value & 0xFF)
|
|
goto tr_stalled;
|
|
ptr = (const void *)&saf1761_otg_hubd;
|
|
len = sizeof(saf1761_otg_hubd);
|
|
goto tr_valid;
|
|
|
|
tr_stalled:
|
|
err = USB_ERR_STALLED;
|
|
tr_valid:
|
|
*plength = len;
|
|
*pptr = ptr;
|
|
return (err);
|
|
}
|
|
|
|
static void
|
|
saf1761_otg_xfer_setup(struct usb_setup_params *parm)
|
|
{
|
|
struct saf1761_otg_softc *sc;
|
|
struct usb_xfer *xfer;
|
|
void *last_obj;
|
|
uint32_t dw1;
|
|
uint32_t ntd;
|
|
uint32_t n;
|
|
uint8_t ep_no;
|
|
uint8_t ep_type;
|
|
|
|
sc = SAF1761_OTG_BUS2SC(parm->udev->bus);
|
|
xfer = parm->curr_xfer;
|
|
|
|
/*
|
|
* NOTE: This driver does not use any of the parameters that
|
|
* are computed from the following values. Just set some
|
|
* reasonable dummies:
|
|
*/
|
|
parm->hc_max_packet_size = 0x500;
|
|
parm->hc_max_packet_count = 1;
|
|
parm->hc_max_frame_size = 0x500;
|
|
|
|
usbd_transfer_setup_sub(parm);
|
|
|
|
/*
|
|
* Compute maximum number of TDs:
|
|
*/
|
|
ep_type = (xfer->endpoint->edesc->bmAttributes & UE_XFERTYPE);
|
|
|
|
if (ep_type == UE_CONTROL) {
|
|
|
|
ntd = xfer->nframes + 1 /* STATUS */ + 1 /* SYNC */ ;
|
|
|
|
} else {
|
|
ntd = xfer->nframes + 1 /* SYNC */ ;
|
|
}
|
|
|
|
/*
|
|
* check if "usbd_transfer_setup_sub" set an error
|
|
*/
|
|
if (parm->err)
|
|
return;
|
|
|
|
/*
|
|
* allocate transfer descriptors
|
|
*/
|
|
last_obj = NULL;
|
|
|
|
ep_no = xfer->endpointno & UE_ADDR;
|
|
|
|
/*
|
|
* Check profile stuff
|
|
*/
|
|
if (parm->udev->flags.usb_mode == USB_MODE_DEVICE) {
|
|
const struct usb_hw_ep_profile *pf;
|
|
|
|
saf1761_otg_get_hw_ep_profile(parm->udev, &pf, ep_no);
|
|
|
|
if (pf == NULL) {
|
|
/* should not happen */
|
|
parm->err = USB_ERR_INVAL;
|
|
return;
|
|
}
|
|
}
|
|
|
|
dw1 = (xfer->address << 3) | (ep_type << 12);
|
|
|
|
switch (parm->udev->speed) {
|
|
case USB_SPEED_FULL:
|
|
case USB_SPEED_LOW:
|
|
/* check if root HUB port is running High Speed */
|
|
if (parm->udev->parent_hs_hub != NULL) {
|
|
dw1 |= SOTG_PTD_DW1_ENABLE_SPLIT;
|
|
dw1 |= (parm->udev->hs_port_no << 18);
|
|
dw1 |= (parm->udev->hs_hub_addr << 25);
|
|
if (parm->udev->speed == USB_SPEED_LOW)
|
|
dw1 |= (1 << 17);
|
|
}
|
|
break;
|
|
default:
|
|
break;
|
|
}
|
|
|
|
/* align data */
|
|
parm->size[0] += ((-parm->size[0]) & (USB_HOST_ALIGN - 1));
|
|
|
|
for (n = 0; n != ntd; n++) {
|
|
|
|
struct saf1761_otg_td *td;
|
|
|
|
if (parm->buf) {
|
|
|
|
td = USB_ADD_BYTES(parm->buf, parm->size[0]);
|
|
|
|
/* init TD */
|
|
td->max_packet_size = xfer->max_packet_size;
|
|
td->ep_index = ep_no;
|
|
td->ep_type = ep_type;
|
|
td->dw1_value = dw1;
|
|
td->uframe = 0;
|
|
if (ep_type == UE_INTERRUPT) {
|
|
if (xfer->interval > 32)
|
|
td->interval = (32 / 2) << 3;
|
|
else
|
|
td->interval = (xfer->interval / 2) << 3;
|
|
} else {
|
|
td->interval = 0;
|
|
}
|
|
td->obj_next = last_obj;
|
|
|
|
last_obj = td;
|
|
}
|
|
parm->size[0] += sizeof(*td);
|
|
}
|
|
|
|
xfer->td_start[0] = last_obj;
|
|
}
|
|
|
|
static void
|
|
saf1761_otg_xfer_unsetup(struct usb_xfer *xfer)
|
|
{
|
|
}
|
|
|
|
static void
|
|
saf1761_otg_ep_init(struct usb_device *udev, struct usb_endpoint_descriptor *edesc,
|
|
struct usb_endpoint *ep)
|
|
{
|
|
DPRINTFN(2, "endpoint=%p, addr=%d, endpt=%d, mode=%d\n",
|
|
ep, udev->address,
|
|
edesc->bEndpointAddress, udev->flags.usb_mode);
|
|
|
|
if (udev->parent_hub == NULL) {
|
|
/* root HUB has special endpoint handling */
|
|
return;
|
|
}
|
|
|
|
if (udev->flags.usb_mode == USB_MODE_DEVICE) {
|
|
if (udev->speed != USB_SPEED_FULL &&
|
|
udev->speed != USB_SPEED_HIGH) {
|
|
/* not supported */
|
|
return;
|
|
}
|
|
switch (edesc->bmAttributes & UE_XFERTYPE) {
|
|
case UE_ISOCHRONOUS:
|
|
ep->methods = &saf1761_otg_device_isoc_methods;
|
|
break;
|
|
default:
|
|
ep->methods = &saf1761_otg_non_isoc_methods;
|
|
break;
|
|
}
|
|
} else {
|
|
switch (edesc->bmAttributes & UE_XFERTYPE) {
|
|
case UE_CONTROL:
|
|
case UE_BULK:
|
|
case UE_INTERRUPT:
|
|
ep->methods = &saf1761_otg_non_isoc_methods;
|
|
break;
|
|
default:
|
|
/* TODO */
|
|
break;
|
|
}
|
|
}
|
|
}
|
|
|
|
static void
|
|
saf1761_otg_set_hw_power_sleep(struct usb_bus *bus, uint32_t state)
|
|
{
|
|
struct saf1761_otg_softc *sc = SAF1761_OTG_BUS2SC(bus);
|
|
|
|
switch (state) {
|
|
case USB_HW_POWER_SUSPEND:
|
|
saf1761_otg_suspend(sc);
|
|
break;
|
|
case USB_HW_POWER_SHUTDOWN:
|
|
saf1761_otg_uninit(sc);
|
|
break;
|
|
case USB_HW_POWER_RESUME:
|
|
saf1761_otg_resume(sc);
|
|
break;
|
|
default:
|
|
break;
|
|
}
|
|
}
|
|
|
|
static const struct usb_bus_methods saf1761_otg_bus_methods =
|
|
{
|
|
.endpoint_init = &saf1761_otg_ep_init,
|
|
.xfer_setup = &saf1761_otg_xfer_setup,
|
|
.xfer_unsetup = &saf1761_otg_xfer_unsetup,
|
|
.get_hw_ep_profile = &saf1761_otg_get_hw_ep_profile,
|
|
.xfer_stall = &saf1761_otg_xfer_stall,
|
|
.set_stall = &saf1761_otg_set_stall,
|
|
.clear_stall = &saf1761_otg_clear_stall,
|
|
.roothub_exec = &saf1761_otg_roothub_exec,
|
|
.xfer_poll = &saf1761_otg_do_poll,
|
|
.set_hw_power_sleep = saf1761_otg_set_hw_power_sleep,
|
|
};
|