d/freebsd-skq
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
25baa69114
freebsd-skq/sys/dev/ath/if_ath_rx.c
adrian 06b6d66e89 Break the RX processing up into smaller chunks of 128 frames each. 
Right now processing a full 512 frame queue takes quite a while (measured
on the order of milliseconds.) Because of this, the TX processing ends up
sometimes preempting the taskqueue:

* userland sends a frame
* it goes in through net80211 and out to ath_start()
* ath_start() will end up either direct dispatching or software queuing a
  frame.

If TX had to wait for RX to finish, it would add quite a few ms of
additional latency to the packet transmission.  This in the past has
caused issues with TCP throughput.

Now, as part of my attempt to bring sanity to the TX/RX paths, the first
step is to make the RX processing happen in smaller 'parts'. That way
when TX is pushed into the ath taskqueue, there won't be so much latency
in the way of things.

The bigger scale change (which will come much later) is to actually
process the frames in the ath_intr taskqueue but process _frames_ in
the ath driver taskqueue.  That would reduce the latency between
processing and requeuing new descriptors. But that'll come later.

The actual work:

* Add ATH_RX_MAX at 128 (static for now);
* break out of the processing loop if npkts reaches ATH_RX_MAX;
* if we processed ATH_RX_MAX or more frames during the processing loop,
  immediately reschedule another RX taskqueue run.  This will handle
  the further frames in the taskqueue.

This should have very minimal impact on the general throughput case,
unless the scheduler is being very very strange or the ath taskqueue
ends up spending a lot of time on non-RX operations (such as TX
completion.)
2012-10-14 20:31:38 +00:00

1130 lines
33 KiB
C
Raw Blame History

/*-
* Copyright (c) 2002-2009 Sam Leffler, Errno Consulting
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer,
* without modification.
* 2. Redistributions in binary form must reproduce at minimum a disclaimer
* similar to the "NO WARRANTY" disclaimer below ("Disclaimer") and any
* redistribution must be conditioned upon including a substantially
* similar Disclaimer requirement for further binary redistribution.
*
* NO WARRANTY
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTIBILITY
* AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
* THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY,
* OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
* IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
* THE POSSIBILITY OF SUCH DAMAGES.
*/
#include <sys/cdefs.h>
__FBSDID("$FreeBSD$");
/*
* Driver for the Atheros Wireless LAN controller.
*
* This software is derived from work of Atsushi Onoe; his contribution
* is greatly appreciated.
*/
#include "opt_inet.h"
#include "opt_ath.h"
/*
* This is needed for register operations which are performed
* by the driver - eg, calls to ath_hal_gettsf32().
*
* It's also required for any AH_DEBUG checks in here, eg the
* module dependencies.
*/
#include "opt_ah.h"
#include "opt_wlan.h"
#include <sys/param.h>
#include <sys/systm.h>
#include <sys/sysctl.h>
#include <sys/mbuf.h>
#include <sys/malloc.h>
#include <sys/lock.h>
#include <sys/mutex.h>
#include <sys/kernel.h>
#include <sys/socket.h>
#include <sys/sockio.h>
#include <sys/errno.h>
#include <sys/callout.h>
#include <sys/bus.h>
#include <sys/endian.h>
#include <sys/kthread.h>
#include <sys/taskqueue.h>
#include <sys/priv.h>
#include <sys/module.h>
#include <sys/ktr.h>
#include <sys/smp.h> /* for mp_ncpus */
#include <machine/bus.h>
#include <net/if.h>
#include <net/if_dl.h>
#include <net/if_media.h>
#include <net/if_types.h>
#include <net/if_arp.h>
#include <net/ethernet.h>
#include <net/if_llc.h>
#include <net80211/ieee80211_var.h>
#include <net80211/ieee80211_regdomain.h>
#ifdef IEEE80211_SUPPORT_SUPERG
#include <net80211/ieee80211_superg.h>
#endif
#ifdef IEEE80211_SUPPORT_TDMA
#include <net80211/ieee80211_tdma.h>
#endif
#include <net/bpf.h>
#ifdef INET
#include <netinet/in.h>
#include <netinet/if_ether.h>
#endif
#include <dev/ath/if_athvar.h>
#include <dev/ath/ath_hal/ah_devid.h> /* XXX for softled */
#include <dev/ath/ath_hal/ah_diagcodes.h>
#include <dev/ath/if_ath_debug.h>
#include <dev/ath/if_ath_misc.h>
#include <dev/ath/if_ath_tsf.h>
#include <dev/ath/if_ath_tx.h>
#include <dev/ath/if_ath_sysctl.h>
#include <dev/ath/if_ath_led.h>
#include <dev/ath/if_ath_keycache.h>
#include <dev/ath/if_ath_rx.h>
#include <dev/ath/if_ath_beacon.h>
#include <dev/ath/if_athdfs.h>
#ifdef ATH_TX99_DIAG
#include <dev/ath/ath_tx99/ath_tx99.h>
#endif
/*
* Calculate the receive filter according to the
* operating mode and state:
*
* o always accept unicast, broadcast, and multicast traffic
* o accept PHY error frames when hardware doesn't have MIB support
* to count and we need them for ANI (sta mode only until recently)
* and we are not scanning (ANI is disabled)
* NB: older hal's add rx filter bits out of sight and we need to
* blindly preserve them
* o probe request frames are accepted only when operating in
* hostap, adhoc, mesh, or monitor modes
* o enable promiscuous mode
* - when in monitor mode
* - if interface marked PROMISC (assumes bridge setting is filtered)
* o accept beacons:
* - when operating in station mode for collecting rssi data when
* the station is otherwise quiet, or
* - when operating in adhoc mode so the 802.11 layer creates
* node table entries for peers,
* - when scanning
* - when doing s/w beacon miss (e.g. for ap+sta)
* - when operating in ap mode in 11g to detect overlapping bss that
* require protection
* - when operating in mesh mode to detect neighbors
* o accept control frames:
* - when in monitor mode
* XXX HT protection for 11n
*/
u_int32_t
ath_calcrxfilter(struct ath_softc *sc)
{
struct ifnet *ifp = sc->sc_ifp;
struct ieee80211com *ic = ifp->if_l2com;
u_int32_t rfilt;
rfilt = HAL_RX_FILTER_UCAST | HAL_RX_FILTER_BCAST | HAL_RX_FILTER_MCAST;
if (!sc->sc_needmib && !sc->sc_scanning)
rfilt |= HAL_RX_FILTER_PHYERR;
if (ic->ic_opmode != IEEE80211_M_STA)
rfilt |= HAL_RX_FILTER_PROBEREQ;
/* XXX ic->ic_monvaps != 0? */
if (ic->ic_opmode == IEEE80211_M_MONITOR || (ifp->if_flags & IFF_PROMISC))
rfilt |= HAL_RX_FILTER_PROM;
if (ic->ic_opmode == IEEE80211_M_STA ||
ic->ic_opmode == IEEE80211_M_IBSS ||
sc->sc_swbmiss || sc->sc_scanning)
rfilt |= HAL_RX_FILTER_BEACON;
/*
* NB: We don't recalculate the rx filter when
* ic_protmode changes; otherwise we could do
* this only when ic_protmode != NONE.
*/
if (ic->ic_opmode == IEEE80211_M_HOSTAP &&
IEEE80211_IS_CHAN_ANYG(ic->ic_curchan))
rfilt |= HAL_RX_FILTER_BEACON;
/*
* Enable hardware PS-POLL RX only for hostap mode;
* STA mode sends PS-POLL frames but never
* receives them.
*/
if (ath_hal_getcapability(sc->sc_ah, HAL_CAP_PSPOLL,
0, NULL) == HAL_OK &&
ic->ic_opmode == IEEE80211_M_HOSTAP)
rfilt |= HAL_RX_FILTER_PSPOLL;
if (sc->sc_nmeshvaps) {
rfilt |= HAL_RX_FILTER_BEACON;
if (sc->sc_hasbmatch)
rfilt |= HAL_RX_FILTER_BSSID;
else
rfilt |= HAL_RX_FILTER_PROM;
}
if (ic->ic_opmode == IEEE80211_M_MONITOR)
rfilt |= HAL_RX_FILTER_CONTROL;
/*
* Enable RX of compressed BAR frames only when doing
* 802.11n. Required for A-MPDU.
*/
if (IEEE80211_IS_CHAN_HT(ic->ic_curchan))
rfilt |= HAL_RX_FILTER_COMPBAR;
/*
* Enable radar PHY errors if requested by the
* DFS module.
*/
if (sc->sc_dodfs)
rfilt |= HAL_RX_FILTER_PHYRADAR;
DPRINTF(sc, ATH_DEBUG_MODE, "%s: RX filter 0x%x, %s if_flags 0x%x\n",
__func__, rfilt, ieee80211_opmode_name[ic->ic_opmode], ifp->if_flags);
return rfilt;
}
static int
ath_legacy_rxbuf_init(struct ath_softc *sc, struct ath_buf *bf)
{
struct ath_hal *ah = sc->sc_ah;
int error;
struct mbuf *m;
struct ath_desc *ds;
m = bf->bf_m;
if (m == NULL) {
/*
* NB: by assigning a page to the rx dma buffer we
* implicitly satisfy the Atheros requirement that
* this buffer be cache-line-aligned and sized to be
* multiple of the cache line size. Not doing this
* causes weird stuff to happen (for the 5210 at least).
*/
m = m_getcl(M_DONTWAIT, MT_DATA, M_PKTHDR);
if (m == NULL) {
DPRINTF(sc, ATH_DEBUG_ANY,
"%s: no mbuf/cluster\n", __func__);
sc->sc_stats.ast_rx_nombuf++;
return ENOMEM;
}
m->m_pkthdr.len = m->m_len = m->m_ext.ext_size;
error = bus_dmamap_load_mbuf_sg(sc->sc_dmat,
bf->bf_dmamap, m,
bf->bf_segs, &bf->bf_nseg,
BUS_DMA_NOWAIT);
if (error != 0) {
DPRINTF(sc, ATH_DEBUG_ANY,
"%s: bus_dmamap_load_mbuf_sg failed; error %d\n",
__func__, error);
sc->sc_stats.ast_rx_busdma++;
m_freem(m);
return error;
}
KASSERT(bf->bf_nseg == 1,
("multi-segment packet; nseg %u", bf->bf_nseg));
bf->bf_m = m;
}
bus_dmamap_sync(sc->sc_dmat, bf->bf_dmamap, BUS_DMASYNC_PREREAD);
/*
* Setup descriptors. For receive we always terminate
* the descriptor list with a self-linked entry so we'll
* not get overrun under high load (as can happen with a
* 5212 when ANI processing enables PHY error frames).
*
* To insure the last descriptor is self-linked we create
* each descriptor as self-linked and add it to the end. As
* each additional descriptor is added the previous self-linked
* entry is ``fixed'' naturally. This should be safe even
* if DMA is happening. When processing RX interrupts we
* never remove/process the last, self-linked, entry on the
* descriptor list. This insures the hardware always has
* someplace to write a new frame.
*/
/*
* 11N: we can no longer afford to self link the last descriptor.
* MAC acknowledges BA status as long as it copies frames to host
* buffer (or rx fifo). This can incorrectly acknowledge packets
* to a sender if last desc is self-linked.
*/
ds = bf->bf_desc;
if (sc->sc_rxslink)
ds->ds_link = bf->bf_daddr; /* link to self */
else
ds->ds_link = 0; /* terminate the list */
ds->ds_data = bf->bf_segs[0].ds_addr;
ath_hal_setuprxdesc(ah, ds
, m->m_len /* buffer size */
, 0
);
if (sc->sc_rxlink != NULL)
*sc->sc_rxlink = bf->bf_daddr;
sc->sc_rxlink = &ds->ds_link;
return 0;
}
/*
* Intercept management frames to collect beacon rssi data
* and to do ibss merges.
*/
void
ath_recv_mgmt(struct ieee80211_node *ni, struct mbuf *m,
int subtype, int rssi, int nf)
{
struct ieee80211vap *vap = ni->ni_vap;
struct ath_softc *sc = vap->iv_ic->ic_ifp->if_softc;
/*
* Call up first so subsequent work can use information
* potentially stored in the node (e.g. for ibss merge).
*/
ATH_VAP(vap)->av_recv_mgmt(ni, m, subtype, rssi, nf);
switch (subtype) {
case IEEE80211_FC0_SUBTYPE_BEACON:
/* update rssi statistics for use by the hal */
/* XXX unlocked check against vap->iv_bss? */
ATH_RSSI_LPF(sc->sc_halstats.ns_avgbrssi, rssi);
if (sc->sc_syncbeacon &&
ni == vap->iv_bss && vap->iv_state == IEEE80211_S_RUN) {
/*
* Resync beacon timers using the tsf of the beacon
* frame we just received.
*/
ath_beacon_config(sc, vap);
}
/* fall thru... */
case IEEE80211_FC0_SUBTYPE_PROBE_RESP:
if (vap->iv_opmode == IEEE80211_M_IBSS &&
vap->iv_state == IEEE80211_S_RUN) {
uint32_t rstamp = sc->sc_lastrs->rs_tstamp;
uint64_t tsf = ath_extend_tsf(sc, rstamp,
ath_hal_gettsf64(sc->sc_ah));
/*
* Handle ibss merge as needed; check the tsf on the
* frame before attempting the merge. The 802.11 spec
* says the station should change it's bssid to match
* the oldest station with the same ssid, where oldest
* is determined by the tsf. Note that hardware
* reconfiguration happens through callback to
* ath_newstate as the state machine will go from
* RUN -> RUN when this happens.
*/
if (le64toh(ni->ni_tstamp.tsf) >= tsf) {
DPRINTF(sc, ATH_DEBUG_STATE,
"ibss merge, rstamp %u tsf %ju "
"tstamp %ju\n", rstamp, (uintmax_t)tsf,
(uintmax_t)ni->ni_tstamp.tsf);
(void) ieee80211_ibss_merge(ni);
}
}
break;
}
}
#ifdef ATH_ENABLE_RADIOTAP_VENDOR_EXT
static void
ath_rx_tap_vendor(struct ifnet *ifp, struct mbuf *m,
const struct ath_rx_status *rs, u_int64_t tsf, int16_t nf)
{
struct ath_softc *sc = ifp->if_softc;
/* Fill in the extension bitmap */
sc->sc_rx_th.wr_ext_bitmap = htole32(1 << ATH_RADIOTAP_VENDOR_HEADER);
/* Fill in the vendor header */
sc->sc_rx_th.wr_vh.vh_oui[0] = 0x7f;
sc->sc_rx_th.wr_vh.vh_oui[1] = 0x03;
sc->sc_rx_th.wr_vh.vh_oui[2] = 0x00;
/* XXX what should this be? */
sc->sc_rx_th.wr_vh.vh_sub_ns = 0;
sc->sc_rx_th.wr_vh.vh_skip_len =
htole16(sizeof(struct ath_radiotap_vendor_hdr));
/* General version info */
sc->sc_rx_th.wr_v.vh_version = 1;
sc->sc_rx_th.wr_v.vh_rx_chainmask = sc->sc_rxchainmask;
/* rssi */
sc->sc_rx_th.wr_v.rssi_ctl[0] = rs->rs_rssi_ctl[0];
sc->sc_rx_th.wr_v.rssi_ctl[1] = rs->rs_rssi_ctl[1];
sc->sc_rx_th.wr_v.rssi_ctl[2] = rs->rs_rssi_ctl[2];
sc->sc_rx_th.wr_v.rssi_ext[0] = rs->rs_rssi_ext[0];
sc->sc_rx_th.wr_v.rssi_ext[1] = rs->rs_rssi_ext[1];
sc->sc_rx_th.wr_v.rssi_ext[2] = rs->rs_rssi_ext[2];
/* evm */
sc->sc_rx_th.wr_v.evm[0] = rs->rs_evm0;
sc->sc_rx_th.wr_v.evm[1] = rs->rs_evm1;
sc->sc_rx_th.wr_v.evm[2] = rs->rs_evm2;
/* XXX TODO: extend this to include 3-stream EVM */
/* phyerr info */
if (rs->rs_status & HAL_RXERR_PHY)
sc->sc_rx_th.wr_v.vh_phyerr_code = rs->rs_phyerr;
else
sc->sc_rx_th.wr_v.vh_phyerr_code = 0xff;
sc->sc_rx_th.wr_v.vh_rs_status = rs->rs_status;
sc->sc_rx_th.wr_v.vh_rssi = rs->rs_rssi;
}
#endif /* ATH_ENABLE_RADIOTAP_VENDOR_EXT */
static void
ath_rx_tap(struct ifnet *ifp, struct mbuf *m,
const struct ath_rx_status *rs, u_int64_t tsf, int16_t nf)
{
#define CHAN_HT20 htole32(IEEE80211_CHAN_HT20)
#define CHAN_HT40U htole32(IEEE80211_CHAN_HT40U)
#define CHAN_HT40D htole32(IEEE80211_CHAN_HT40D)
#define CHAN_HT (CHAN_HT20|CHAN_HT40U|CHAN_HT40D)
struct ath_softc *sc = ifp->if_softc;
const HAL_RATE_TABLE *rt;
uint8_t rix;
rt = sc->sc_currates;
KASSERT(rt != NULL, ("no rate table, mode %u", sc->sc_curmode));
rix = rt->rateCodeToIndex[rs->rs_rate];
sc->sc_rx_th.wr_rate = sc->sc_hwmap[rix].ieeerate;
sc->sc_rx_th.wr_flags = sc->sc_hwmap[rix].rxflags;
#ifdef AH_SUPPORT_AR5416
sc->sc_rx_th.wr_chan_flags &= ~CHAN_HT;
if (sc->sc_rx_th.wr_rate & IEEE80211_RATE_MCS) { /* HT rate */
struct ieee80211com *ic = ifp->if_l2com;
if ((rs->rs_flags & HAL_RX_2040) == 0)
sc->sc_rx_th.wr_chan_flags |= CHAN_HT20;
else if (IEEE80211_IS_CHAN_HT40U(ic->ic_curchan))
sc->sc_rx_th.wr_chan_flags |= CHAN_HT40U;
else
sc->sc_rx_th.wr_chan_flags |= CHAN_HT40D;
if ((rs->rs_flags & HAL_RX_GI) == 0)
sc->sc_rx_th.wr_flags |= IEEE80211_RADIOTAP_F_SHORTGI;
}
#endif
sc->sc_rx_th.wr_tsf = htole64(ath_extend_tsf(sc, rs->rs_tstamp, tsf));
if (rs->rs_status & HAL_RXERR_CRC)
sc->sc_rx_th.wr_flags |= IEEE80211_RADIOTAP_F_BADFCS;
/* XXX propagate other error flags from descriptor */
sc->sc_rx_th.wr_antnoise = nf;
sc->sc_rx_th.wr_antsignal = nf + rs->rs_rssi;
sc->sc_rx_th.wr_antenna = rs->rs_antenna;
#undef CHAN_HT
#undef CHAN_HT20
#undef CHAN_HT40U
#undef CHAN_HT40D
}
static void
ath_handle_micerror(struct ieee80211com *ic,
struct ieee80211_frame *wh, int keyix)
{
struct ieee80211_node *ni;
/* XXX recheck MIC to deal w/ chips that lie */
/* XXX discard MIC errors on !data frames */
ni = ieee80211_find_rxnode(ic, (const struct ieee80211_frame_min *) wh);
if (ni != NULL) {
ieee80211_notify_michael_failure(ni->ni_vap, wh, keyix);
ieee80211_free_node(ni);
}
}
int
ath_rx_pkt(struct ath_softc *sc, struct ath_rx_status *rs, HAL_STATUS status,
uint64_t tsf, int nf, HAL_RX_QUEUE qtype, struct ath_buf *bf)
{
struct ath_hal *ah = sc->sc_ah;
struct mbuf *m = bf->bf_m;
uint64_t rstamp;
int len, type;
struct ifnet *ifp = sc->sc_ifp;
struct ieee80211com *ic = ifp->if_l2com;
struct ieee80211_node *ni;
int is_good = 0;
struct ath_rx_edma *re = &sc->sc_rxedma[qtype];
/*
* Calculate the correct 64 bit TSF given
* the TSF64 register value and rs_tstamp.
*/
rstamp = ath_extend_tsf(sc, rs->rs_tstamp, tsf);
/* These aren't specifically errors */
#ifdef AH_SUPPORT_AR5416
if (rs->rs_flags & HAL_RX_GI)
sc->sc_stats.ast_rx_halfgi++;
if (rs->rs_flags & HAL_RX_2040)
sc->sc_stats.ast_rx_2040++;
if (rs->rs_flags & HAL_RX_DELIM_CRC_PRE)
sc->sc_stats.ast_rx_pre_crc_err++;
if (rs->rs_flags & HAL_RX_DELIM_CRC_POST)
sc->sc_stats.ast_rx_post_crc_err++;
if (rs->rs_flags & HAL_RX_DECRYPT_BUSY)
sc->sc_stats.ast_rx_decrypt_busy_err++;
if (rs->rs_flags & HAL_RX_HI_RX_CHAIN)
sc->sc_stats.ast_rx_hi_rx_chain++;
#endif /* AH_SUPPORT_AR5416 */
if (rs->rs_status != 0) {
if (rs->rs_status & HAL_RXERR_CRC)
sc->sc_stats.ast_rx_crcerr++;
if (rs->rs_status & HAL_RXERR_FIFO)
sc->sc_stats.ast_rx_fifoerr++;
if (rs->rs_status & HAL_RXERR_PHY) {
sc->sc_stats.ast_rx_phyerr++;
/* Process DFS radar events */
if ((rs->rs_phyerr == HAL_PHYERR_RADAR) ||
(rs->rs_phyerr == HAL_PHYERR_FALSE_RADAR_EXT)) {
/* Since we're touching the frame data, sync it */
bus_dmamap_sync(sc->sc_dmat,
bf->bf_dmamap,
BUS_DMASYNC_POSTREAD);
/* Now pass it to the radar processing code */
ath_dfs_process_phy_err(sc, m, rstamp, rs);
}
/* Be suitably paranoid about receiving phy errors out of the stats array bounds */
if (rs->rs_phyerr < 64)
sc->sc_stats.ast_rx_phy[rs->rs_phyerr]++;
goto rx_error; /* NB: don't count in ierrors */
}
if (rs->rs_status & HAL_RXERR_DECRYPT) {
/*
* Decrypt error. If the error occurred
* because there was no hardware key, then
* let the frame through so the upper layers
* can process it. This is necessary for 5210
* parts which have no way to setup a ``clear''
* key cache entry.
*
* XXX do key cache faulting
*/
if (rs->rs_keyix == HAL_RXKEYIX_INVALID)
goto rx_accept;
sc->sc_stats.ast_rx_badcrypt++;
}
/*
* Similar as above - if the failure was a keymiss
* just punt it up to the upper layers for now.
*/
if (rs->rs_status & HAL_RXERR_KEYMISS) {
sc->sc_stats.ast_rx_keymiss++;
goto rx_accept;
}
if (rs->rs_status & HAL_RXERR_MIC) {
sc->sc_stats.ast_rx_badmic++;
/*
* Do minimal work required to hand off
* the 802.11 header for notification.
*/
/* XXX frag's and qos frames */
len = rs->rs_datalen;
if (len >= sizeof (struct ieee80211_frame)) {
bus_dmamap_sync(sc->sc_dmat,
bf->bf_dmamap,
BUS_DMASYNC_POSTREAD);
ath_handle_micerror(ic,
mtod(m, struct ieee80211_frame *),
sc->sc_splitmic ?
rs->rs_keyix-32 : rs->rs_keyix);
}
}
ifp->if_ierrors++;
rx_error:
/*
* Cleanup any pending partial frame.
*/
if (re->m_rxpending != NULL) {
m_freem(re->m_rxpending);
re->m_rxpending = NULL;
}
/*
* When a tap is present pass error frames
* that have been requested. By default we
* pass decrypt+mic errors but others may be
* interesting (e.g. crc).
*/
if (ieee80211_radiotap_active(ic) &&
(rs->rs_status & sc->sc_monpass)) {
bus_dmamap_sync(sc->sc_dmat, bf->bf_dmamap,
BUS_DMASYNC_POSTREAD);
/* NB: bpf needs the mbuf length setup */
len = rs->rs_datalen;
m->m_pkthdr.len = m->m_len = len;
bf->bf_m = NULL;
ath_rx_tap(ifp, m, rs, rstamp, nf);
#ifdef ATH_ENABLE_RADIOTAP_VENDOR_EXT
ath_rx_tap_vendor(ifp, m, rs, rstamp, nf);
#endif /* ATH_ENABLE_RADIOTAP_VENDOR_EXT */
ieee80211_radiotap_rx_all(ic, m);
m_freem(m);
}
/* XXX pass MIC errors up for s/w reclaculation */
goto rx_next;
}
rx_accept:
/*
* Sync and unmap the frame. At this point we're
* committed to passing the mbuf somewhere so clear
* bf_m; this means a new mbuf must be allocated
* when the rx descriptor is setup again to receive
* another frame.
*/
bus_dmamap_sync(sc->sc_dmat, bf->bf_dmamap, BUS_DMASYNC_POSTREAD);
bus_dmamap_unload(sc->sc_dmat, bf->bf_dmamap);
bf->bf_m = NULL;
len = rs->rs_datalen;
m->m_len = len;
if (rs->rs_more) {
/*
* Frame spans multiple descriptors; save
* it for the next completed descriptor, it
* will be used to construct a jumbogram.
*/
if (re->m_rxpending != NULL) {
/* NB: max frame size is currently 2 clusters */
sc->sc_stats.ast_rx_toobig++;
m_freem(re->m_rxpending);
}
m->m_pkthdr.rcvif = ifp;
m->m_pkthdr.len = len;
re->m_rxpending = m;
goto rx_next;
} else if (re->m_rxpending != NULL) {
/*
* This is the second part of a jumbogram,
* chain it to the first mbuf, adjust the
* frame length, and clear the rxpending state.
*/
re->m_rxpending->m_next = m;
re->m_rxpending->m_pkthdr.len += len;
m = re->m_rxpending;
re->m_rxpending = NULL;
} else {
/*
* Normal single-descriptor receive; setup
* the rcvif and packet length.
*/
m->m_pkthdr.rcvif = ifp;
m->m_pkthdr.len = len;
}
/*
* Validate rs->rs_antenna.
*
* Some users w/ AR9285 NICs have reported crashes
* here because rs_antenna field is bogusly large.
* Let's enforce the maximum antenna limit of 8
* (and it shouldn't be hard coded, but that's a
* separate problem) and if there's an issue, print
* out an error and adjust rs_antenna to something
* sensible.
*
* This code should be removed once the actual
* root cause of the issue has been identified.
* For example, it may be that the rs_antenna
* field is only valid for the lsat frame of
* an aggregate and it just happens that it is
* "mostly" right. (This is a general statement -
* the majority of the statistics are only valid
* for the last frame in an aggregate.
*/
if (rs->rs_antenna > 7) {
device_printf(sc->sc_dev, "%s: rs_antenna > 7 (%d)\n",
__func__, rs->rs_antenna);
#ifdef ATH_DEBUG
ath_printrxbuf(sc, bf, 0, status == HAL_OK);
#endif /* ATH_DEBUG */
rs->rs_antenna = 0; /* XXX better than nothing */
}
ifp->if_ipackets++;
sc->sc_stats.ast_ant_rx[rs->rs_antenna]++;
/*
* Populate the rx status block. When there are bpf
* listeners we do the additional work to provide
* complete status. Otherwise we fill in only the
* material required by ieee80211_input. Note that
* noise setting is filled in above.
*/
if (ieee80211_radiotap_active(ic)) {
ath_rx_tap(ifp, m, rs, rstamp, nf);
#ifdef ATH_ENABLE_RADIOTAP_VENDOR_EXT
ath_rx_tap_vendor(ifp, m, rs, rstamp, nf);
#endif /* ATH_ENABLE_RADIOTAP_VENDOR_EXT */
}
/*
* From this point on we assume the frame is at least
* as large as ieee80211_frame_min; verify that.
*/
if (len < IEEE80211_MIN_LEN) {
if (!ieee80211_radiotap_active(ic)) {
DPRINTF(sc, ATH_DEBUG_RECV,
"%s: short packet %d\n", __func__, len);
sc->sc_stats.ast_rx_tooshort++;
} else {
/* NB: in particular this captures ack's */
ieee80211_radiotap_rx_all(ic, m);
}
m_freem(m);
goto rx_next;
}
if (IFF_DUMPPKTS(sc, ATH_DEBUG_RECV)) {
const HAL_RATE_TABLE *rt = sc->sc_currates;
uint8_t rix = rt->rateCodeToIndex[rs->rs_rate];
ieee80211_dump_pkt(ic, mtod(m, caddr_t), len,
sc->sc_hwmap[rix].ieeerate, rs->rs_rssi);
}
m_adj(m, -IEEE80211_CRC_LEN);
/*
* Locate the node for sender, track state, and then
* pass the (referenced) node up to the 802.11 layer
* for its use.
*/
ni = ieee80211_find_rxnode_withkey(ic,
mtod(m, const struct ieee80211_frame_min *),
rs->rs_keyix == HAL_RXKEYIX_INVALID ?
IEEE80211_KEYIX_NONE : rs->rs_keyix);
sc->sc_lastrs = rs;
#ifdef AH_SUPPORT_AR5416
if (rs->rs_isaggr)
sc->sc_stats.ast_rx_agg++;
#endif /* AH_SUPPORT_AR5416 */
if (ni != NULL) {
/*
* Only punt packets for ampdu reorder processing for
* 11n nodes; net80211 enforces that M_AMPDU is only
* set for 11n nodes.
*/
if (ni->ni_flags & IEEE80211_NODE_HT)
m->m_flags |= M_AMPDU;
/*
* Sending station is known, dispatch directly.
*/
type = ieee80211_input(ni, m, rs->rs_rssi, nf);
ieee80211_free_node(ni);
/*
* Arrange to update the last rx timestamp only for
* frames from our ap when operating in station mode.
* This assumes the rx key is always setup when
* associated.
*/
if (ic->ic_opmode == IEEE80211_M_STA &&
rs->rs_keyix != HAL_RXKEYIX_INVALID)
is_good = 1;
} else {
type = ieee80211_input_all(ic, m, rs->rs_rssi, nf);
}
/*
* Track rx rssi and do any rx antenna management.
*/
ATH_RSSI_LPF(sc->sc_halstats.ns_avgrssi, rs->rs_rssi);
if (sc->sc_diversity) {
/*
* When using fast diversity, change the default rx
* antenna if diversity chooses the other antenna 3
* times in a row.
*/
if (sc->sc_defant != rs->rs_antenna) {
if (++sc->sc_rxotherant >= 3)
ath_setdefantenna(sc, rs->rs_antenna);
} else
sc->sc_rxotherant = 0;
}
/* Newer school diversity - kite specific for now */
/* XXX perhaps migrate the normal diversity code to this? */
if ((ah)->ah_rxAntCombDiversity)
(*(ah)->ah_rxAntCombDiversity)(ah, rs, ticks, hz);
if (sc->sc_softled) {
/*
* Blink for any data frame. Otherwise do a
* heartbeat-style blink when idle. The latter
* is mainly for station mode where we depend on
* periodic beacon frames to trigger the poll event.
*/
if (type == IEEE80211_FC0_TYPE_DATA) {
const HAL_RATE_TABLE *rt = sc->sc_currates;
ath_led_event(sc,
rt->rateCodeToIndex[rs->rs_rate]);
} else if (ticks - sc->sc_ledevent >= sc->sc_ledidle)
ath_led_event(sc, 0);
}
rx_next:
return (is_good);
}
#define ATH_RX_MAX 128
static void
ath_rx_proc(struct ath_softc *sc, int resched)
{
#define PA2DESC(_sc, _pa) \
((struct ath_desc *)((caddr_t)(_sc)->sc_rxdma.dd_desc + \
((_pa) - (_sc)->sc_rxdma.dd_desc_paddr)))
struct ath_buf *bf;
struct ifnet *ifp = sc->sc_ifp;
struct ath_hal *ah = sc->sc_ah;
#ifdef IEEE80211_SUPPORT_SUPERG
struct ieee80211com *ic = ifp->if_l2com;
#endif
struct ath_desc *ds;
struct ath_rx_status *rs;
struct mbuf *m;
int ngood;
HAL_STATUS status;
int16_t nf;
u_int64_t tsf;
int npkts = 0;
/* XXX we must not hold the ATH_LOCK here */
ATH_UNLOCK_ASSERT(sc);
ATH_PCU_UNLOCK_ASSERT(sc);
ATH_PCU_LOCK(sc);
sc->sc_rxproc_cnt++;
ATH_PCU_UNLOCK(sc);
DPRINTF(sc, ATH_DEBUG_RX_PROC, "%s: called\n", __func__);
ngood = 0;
nf = ath_hal_getchannoise(ah, sc->sc_curchan);
sc->sc_stats.ast_rx_noise = nf;
tsf = ath_hal_gettsf64(ah);
do {
/*
* Don't process too many packets at a time; give the
* TX thread time to also run - otherwise the TX
* latency can jump by quite a bit, causing throughput
* degredation.
*/
if (npkts >= ATH_RX_MAX)
break;
bf = TAILQ_FIRST(&sc->sc_rxbuf);
if (sc->sc_rxslink && bf == NULL) { /* NB: shouldn't happen */
if_printf(ifp, "%s: no buffer!\n", __func__);
break;
} else if (bf == NULL) {
/*
* End of List:
* this can happen for non-self-linked RX chains
*/
sc->sc_stats.ast_rx_hitqueueend++;
break;
}
m = bf->bf_m;
if (m == NULL) { /* NB: shouldn't happen */
/*
* If mbuf allocation failed previously there
* will be no mbuf; try again to re-populate it.
*/
/* XXX make debug msg */
if_printf(ifp, "%s: no mbuf!\n", __func__);
TAILQ_REMOVE(&sc->sc_rxbuf, bf, bf_list);
goto rx_proc_next;
}
ds = bf->bf_desc;
if (ds->ds_link == bf->bf_daddr) {
/* NB: never process the self-linked entry at the end */
sc->sc_stats.ast_rx_hitqueueend++;
break;
}
/* XXX sync descriptor memory */
/*
* Must provide the virtual address of the current
* descriptor, the physical address, and the virtual
* address of the next descriptor in the h/w chain.
* This allows the HAL to look ahead to see if the
* hardware is done with a descriptor by checking the
* done bit in the following descriptor and the address
* of the current descriptor the DMA engine is working
* on. All this is necessary because of our use of
* a self-linked list to avoid rx overruns.
*/
rs = &bf->bf_status.ds_rxstat;
status = ath_hal_rxprocdesc(ah, ds,
bf->bf_daddr, PA2DESC(sc, ds->ds_link), rs);
#ifdef ATH_DEBUG
if (sc->sc_debug & ATH_DEBUG_RECV_DESC)
ath_printrxbuf(sc, bf, 0, status == HAL_OK);
#endif
if (status == HAL_EINPROGRESS)
break;
TAILQ_REMOVE(&sc->sc_rxbuf, bf, bf_list);
npkts++;
/*
* Process a single frame.
*/
if (ath_rx_pkt(sc, rs, status, tsf, nf, HAL_RX_QUEUE_HP, bf))
ngood++;
rx_proc_next:
TAILQ_INSERT_TAIL(&sc->sc_rxbuf, bf, bf_list);
} while (ath_rxbuf_init(sc, bf) == 0);
/* rx signal state monitoring */
ath_hal_rxmonitor(ah, &sc->sc_halstats, sc->sc_curchan);
if (ngood)
sc->sc_lastrx = tsf;
ATH_KTR(sc, ATH_KTR_RXPROC, 2, "ath_rx_proc: npkts=%d, ngood=%d", npkts, ngood);
/* Queue DFS tasklet if needed */
if (resched && ath_dfs_tasklet_needed(sc, sc->sc_curchan))
taskqueue_enqueue(sc->sc_tq, &sc->sc_dfstask);
/*
* Now that all the RX frames were handled that
* need to be handled, kick the PCU if there's
* been an RXEOL condition.
*/
ATH_PCU_LOCK(sc);
if (resched && sc->sc_kickpcu) {
ATH_KTR(sc, ATH_KTR_ERROR, 0, "ath_rx_proc: kickpcu");
device_printf(sc->sc_dev, "%s: kickpcu; handled %d packets\n",
__func__, npkts);
/* XXX rxslink? */
/*
* XXX can we hold the PCU lock here?
* Are there any net80211 buffer calls involved?
*/
bf = TAILQ_FIRST(&sc->sc_rxbuf);
ath_hal_putrxbuf(ah, bf->bf_daddr, HAL_RX_QUEUE_HP);
ath_hal_rxena(ah); /* enable recv descriptors */
ath_mode_init(sc); /* set filters, etc. */
ath_hal_startpcurecv(ah); /* re-enable PCU/DMA engine */
ath_hal_intrset(ah, sc->sc_imask);
sc->sc_kickpcu = 0;
}
ATH_PCU_UNLOCK(sc);
/* XXX check this inside of IF_LOCK? */
if (resched && (ifp->if_drv_flags & IFF_DRV_OACTIVE) == 0) {
#ifdef IEEE80211_SUPPORT_SUPERG
ieee80211_ff_age_all(ic, 100);
#endif
if (!IFQ_IS_EMPTY(&ifp->if_snd))
ath_tx_kick(sc);
}
#undef PA2DESC
/*
* If we hit the maximum number of frames in this round,
* reschedule for another immediate pass. This gives
* the TX and TX completion routines time to run, which
* will reduce latency.
*/
if (npkts >= ATH_RX_MAX)
taskqueue_enqueue(sc->sc_tq, &sc->sc_rxtask);
ATH_PCU_LOCK(sc);
sc->sc_rxproc_cnt--;
ATH_PCU_UNLOCK(sc);
}
#undef ATH_RX_MAX
/*
* Only run the RX proc if it's not already running.
* Since this may get run as part of the reset/flush path,
* the task can't clash with an existing, running tasklet.
*/
static void
ath_legacy_rx_tasklet(void *arg, int npending)
{
struct ath_softc *sc = arg;
ATH_KTR(sc, ATH_KTR_RXPROC, 1, "ath_rx_proc: pending=%d", npending);
DPRINTF(sc, ATH_DEBUG_RX_PROC, "%s: pending %u\n", __func__, npending);
ATH_PCU_LOCK(sc);
if (sc->sc_inreset_cnt > 0) {
device_printf(sc->sc_dev,
"%s: sc_inreset_cnt > 0; skipping\n", __func__);
ATH_PCU_UNLOCK(sc);
return;
}
ATH_PCU_UNLOCK(sc);
ath_rx_proc(sc, 1);
}
static void
ath_legacy_flushrecv(struct ath_softc *sc)
{
ath_rx_proc(sc, 0);
}
/*
* Disable the receive h/w in preparation for a reset.
*/
static void
ath_legacy_stoprecv(struct ath_softc *sc, int dodelay)
{
#define PA2DESC(_sc, _pa) \
((struct ath_desc *)((caddr_t)(_sc)->sc_rxdma.dd_desc + \
((_pa) - (_sc)->sc_rxdma.dd_desc_paddr)))
struct ath_hal *ah = sc->sc_ah;
ath_hal_stoppcurecv(ah); /* disable PCU */
ath_hal_setrxfilter(ah, 0); /* clear recv filter */
ath_hal_stopdmarecv(ah); /* disable DMA engine */
/*
* TODO: see if this particular DELAY() is required; it may be
* masking some missing FIFO flush or DMA sync.
*/
#if 0
if (dodelay)
#endif
DELAY(3000); /* 3ms is long enough for 1 frame */
#ifdef ATH_DEBUG
if (sc->sc_debug & (ATH_DEBUG_RESET | ATH_DEBUG_FATAL)) {
struct ath_buf *bf;
u_int ix;
device_printf(sc->sc_dev,
"%s: rx queue %p, link %p\n",
__func__,
(caddr_t)(uintptr_t) ath_hal_getrxbuf(ah, HAL_RX_QUEUE_HP),
sc->sc_rxlink);
ix = 0;
TAILQ_FOREACH(bf, &sc->sc_rxbuf, bf_list) {
struct ath_desc *ds = bf->bf_desc;
struct ath_rx_status *rs = &bf->bf_status.ds_rxstat;
HAL_STATUS status = ath_hal_rxprocdesc(ah, ds,
bf->bf_daddr, PA2DESC(sc, ds->ds_link), rs);
if (status == HAL_OK || (sc->sc_debug & ATH_DEBUG_FATAL))
ath_printrxbuf(sc, bf, ix, status == HAL_OK);
ix++;
}
}
#endif
/*
* Free both high/low RX pending, just in case.
*/
if (sc->sc_rxedma[HAL_RX_QUEUE_LP].m_rxpending != NULL) {
m_freem(sc->sc_rxedma[HAL_RX_QUEUE_LP].m_rxpending);
sc->sc_rxedma[HAL_RX_QUEUE_LP].m_rxpending = NULL;
}
if (sc->sc_rxedma[HAL_RX_QUEUE_HP].m_rxpending != NULL) {
m_freem(sc->sc_rxedma[HAL_RX_QUEUE_HP].m_rxpending);
sc->sc_rxedma[HAL_RX_QUEUE_HP].m_rxpending = NULL;
}
sc->sc_rxlink = NULL; /* just in case */
#undef PA2DESC
}
/*
* Enable the receive h/w following a reset.
*/
static int
ath_legacy_startrecv(struct ath_softc *sc)
{
struct ath_hal *ah = sc->sc_ah;
struct ath_buf *bf;
sc->sc_rxlink = NULL;
sc->sc_rxedma[HAL_RX_QUEUE_LP].m_rxpending = NULL;
sc->sc_rxedma[HAL_RX_QUEUE_HP].m_rxpending = NULL;
TAILQ_FOREACH(bf, &sc->sc_rxbuf, bf_list) {
int error = ath_rxbuf_init(sc, bf);
if (error != 0) {
DPRINTF(sc, ATH_DEBUG_RECV,
"%s: ath_rxbuf_init failed %d\n",
__func__, error);
return error;
}
}
bf = TAILQ_FIRST(&sc->sc_rxbuf);
ath_hal_putrxbuf(ah, bf->bf_daddr, HAL_RX_QUEUE_HP);
ath_hal_rxena(ah); /* enable recv descriptors */
ath_mode_init(sc); /* set filters, etc. */
ath_hal_startpcurecv(ah); /* re-enable PCU/DMA engine */
return 0;
}
static int
ath_legacy_dma_rxsetup(struct ath_softc *sc)
{
int error;
error = ath_descdma_setup(sc, &sc->sc_rxdma, &sc->sc_rxbuf,
"rx", sizeof(struct ath_desc), ath_rxbuf, 1);
if (error != 0)
return (error);
return (0);
}
static int
ath_legacy_dma_rxteardown(struct ath_softc *sc)
{
if (sc->sc_rxdma.dd_desc_len != 0)
ath_descdma_cleanup(sc, &sc->sc_rxdma, &sc->sc_rxbuf);
return (0);
}
void
ath_recv_setup_legacy(struct ath_softc *sc)
{
/* Sensible legacy defaults */
sc->sc_rx_statuslen = 0;
sc->sc_rx.recv_start = ath_legacy_startrecv;
sc->sc_rx.recv_stop = ath_legacy_stoprecv;
sc->sc_rx.recv_flush = ath_legacy_flushrecv;
sc->sc_rx.recv_tasklet = ath_legacy_rx_tasklet;
sc->sc_rx.recv_rxbuf_init = ath_legacy_rxbuf_init;
sc->sc_rx.recv_setup = ath_legacy_dma_rxsetup;
sc->sc_rx.recv_teardown = ath_legacy_dma_rxteardown;
}
Reference in New Issue View Git Blame Copy Permalink