freebsd kernel with SKQ
296e094bd8
- Don't use a single big DMA block for all rings. Create separate DMA area for each ring instead. Currently the following DMA areas are created: Event ring, standard RX ring, jumbo RX ring, RX return ring, hardware MAC statistics and producer/consumer status area. For Tigon II, mini RX ring and TX ring are additionally created. - Added missing bus_dmamap_sync(9) in various TX/RX paths. - TX ring is no longer created for Tigon 1 such that it saves more resources on Tigon 1. - Data sheet is not clear about alignment requirement of each ring so use 32 bytes alignment for normal DMA area but use 64 bytes alignment for jumbo RX ring where the extended RX descriptor size is 64 bytes. - For each TX/RX buffers use separate DMA tag(e.g. the size of a DMA segment, total size of DMA segments etc). - Tigon allows separate DMA area for event producer, RX return producer and TX consumer which is really cool feature. This means TX and RX path could be independently run in parallel. However ti(4) uses a single driver lock so it's meaningless to have separate DMA area for these producer/consumer such that this change creates a single status DMA area. - It seems Tigon has no limits on DMA address space and I also don't see any problem with that but old comments in driver indicates there could be issues on descriptors being located in 64bit region. Introduce a tunable, dev.ti.%d.dac, to disable using 64bit DMA in driver. The default is 0 which means it would use full 64bit DMA. If there are DMA issues, users can disable it by setting the tunable to 0. - Do not increase watchdog timer in ti_txeof(). Previously driver increased the watchdog timer whenever there are queued TX frames. - When stat ticks is set to 0, skip processing ti_stats_update(), avoiding bus_dmamap_sync(9) and updating if_collisions counter. - MTU does not include FCS bytes, replace it with ETHER_VLAN_ENCAP_LEN. With these changes, ti(4) should work on PAE environments. Many thanks to Jay Borkenhagen for remote hardware access. |
||
|---|---|---|
| bin | ||
| cddl | ||
| contrib | ||
| crypto | ||
| etc | ||
| games | ||
| gnu | ||
| include | ||
| kerberos5 | ||
| lib | ||
| libexec | ||
| release | ||
| rescue | ||
| sbin | ||
| secure | ||
| share | ||
| sys | ||
| tools | ||
| usr.bin | ||
| usr.sbin | ||
| COPYRIGHT | ||
| LOCKS | ||
| MAINTAINERS | ||
| Makefile | ||
| Makefile.inc1 | ||
| Makefile.mips | ||
| ObsoleteFiles.inc | ||
| README | ||
| UPDATING | ||
This is the top level of the FreeBSD source directory. This file was last revised on: $FreeBSD$ For copyright information, please see the file COPYRIGHT in this directory (additional copyright information also exists for some sources in this tree - please see the specific source directories for more information). The Makefile in this directory supports a number of targets for building components (or all) of the FreeBSD source tree, the most commonly used one being ``world'', which rebuilds and installs everything in the FreeBSD system from the source tree except the kernel, the kernel-modules and the contents of /etc. The ``world'' target should only be used in cases where the source tree has not changed from the currently running version. See: http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/makeworld.html for more information, including setting make(1) variables. The ``buildkernel'' and ``installkernel'' targets build and install the kernel and the modules (see below). Please see the top of the Makefile in this directory for more information on the standard build targets and compile-time flags. Building a kernel is a somewhat more involved process, documentation for which can be found at: http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/kernelconfig.html And in the config(8) man page. Note: If you want to build and install the kernel with the ``buildkernel'' and ``installkernel'' targets, you might need to build world before. More information is available in the handbook. The sample kernel configuration files reside in the sys/<arch>/conf sub-directory (assuming that you've installed the kernel sources), the file named GENERIC being the one used to build your initial installation kernel. The file NOTES contains entries and documentation for all possible devices, not just those commonly used. It is the successor of the ancient LINT file, but in contrast to LINT, it is not buildable as a kernel but a pure reference and documentation file. Source Roadmap: --------------- bin System/user commands. cddl Various commands and libraries under the Common Development and Distribution License. contrib Packages contributed by 3rd parties. crypto Cryptography stuff (see crypto/README). etc Template files for /etc. games Amusements. gnu Various commands and libraries under the GNU Public License. Please see gnu/COPYING* for more information. include System include files. kerberos5 Kerberos5 (Heimdal) package. lib System libraries. libexec System daemons. release Release building Makefile & associated tools. rescue Build system for statically linked /rescue utilities. sbin System commands. secure Cryptographic libraries and commands. share Shared resources. sys Kernel sources. tools Utilities for regression testing and miscellaneous tasks. usr.bin User commands. usr.sbin System administration commands. For information on synchronizing your source tree with one or more of the FreeBSD Project's development branches, please see: http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/synching.html