1fa24a09c7
This is based on Voxware 3.5, and corresponds to Amancio's `guspnp21'. Bug reports to Amancio, please!
100 lines
4.2 KiB
Plaintext
100 lines
4.2 KiB
Plaintext
Building a loadable sound driver
|
|
================================
|
|
|
|
Loadable module support in version 3.5 of VoxWare is mostly rewritten since
|
|
the previous version (3.0.1). This means that some things have changed.
|
|
|
|
To compile the sound driver as a loadable module you have to perform
|
|
the following steps:
|
|
|
|
1) Install modules-1.2.8.tar.gz package (or later if available).
|
|
2a) Check that symbol remap_page_range is defined in linux/init/ksyms.c.
|
|
Insert a line containing "X(remap_page_range)," if required. The driver will
|
|
not load if this line is missing.
|
|
2b) Recompile kernel with soundcard support disabled.
|
|
3) Boot the new kernel.
|
|
4) cd to the sound driver source directory (this directory). It's no
|
|
longer required that the sound driver sources are installed in the
|
|
kernel source tree (linux/drivers/sound). When installing a separately
|
|
distributed sound driver you may install the sources for example to
|
|
/usr/src/sound.
|
|
5) Execute make in the sound driver source directory. Enter
|
|
configuration parameters as described in Readme.cards. Then just wait until
|
|
the driver is compiled OK.
|
|
6) Copy sound.o to the directory where insmod expects to find it.
|
|
("make install" copies it to /lib/modules/misc).
|
|
7) Use command "insmod sound" to load the driver.
|
|
|
|
8) The sound driver can be removed using command "rmmod sound".
|
|
|
|
|
|
Parameters accepted by the loadable sound driver
|
|
================================================
|
|
|
|
Setting DMA buffer size
|
|
-----------------------
|
|
|
|
The driver allocates a DMA buffer (or two for full duplex devices)
|
|
every time the audio device (/dev/dsp or /dev/audio) is opened
|
|
and frees it when the device is closed. Size of this buffer is defined
|
|
when the driver is configured (the last question). The buffer size
|
|
can be redefined when loading the driver if required (note that this is
|
|
an optional feature which is not normally required). The buffer size
|
|
is redefined by adding dma_pagesize= parameter to the insmod command line.
|
|
For example:
|
|
|
|
insmod sound dma_buffsize=32768
|
|
|
|
Minimum buffer size is 4096 and the maximum depends on the DMA channe.
|
|
For 8 bit channels (0 to 3) the limit is 64k and for 16 bit ones (5 to 7)
|
|
it's 128k. Driver selects a suitable buffer size automaticly in case
|
|
you try to spesify an invalid size.
|
|
|
|
Q: What is the right DMA buffer size?
|
|
|
|
A: It depends on the sampling rate, machine speed and the load of the system.
|
|
Large buffers are required on slow machines, when recording/playing CD-quality
|
|
audio or when there are other processes running on the same system. Also
|
|
recording to hard disk is likely to require large buffers.
|
|
|
|
Very small buffers are sufficient when you are just playing 8kHz audio files
|
|
on an empty P133 system. Using a 128k byffer just wastes 120k (or 250k)
|
|
of valuable physical RAM memory.
|
|
|
|
The right buffer sice can be easily found by making some experiments
|
|
with the dma_buffsize= parameter. I use usually 16k buffers on a DX4/100 system
|
|
and 64k on an old 386 system.
|
|
|
|
NOTE! DMA buffers are used only by /dev/audio# and /dev/dsp# devices.
|
|
Other device files don't use them but there are two exceptions:
|
|
GUS driver uses DMA buffers when loading samples to the card.
|
|
Ensoniq SoundScape driver uses them when doanloading the microcode
|
|
file (sndscape.co[012]) to the card. Using large buffers doesn't
|
|
increase performance in these cases.
|
|
|
|
Configuring device parameters when loading the driver
|
|
-----------------------------------------------------
|
|
|
|
The loadable version of the sound driver accepts now the same
|
|
sound= parameter that has been available in the LILO command line.
|
|
In this way it's possible to change I/O port, IRQ and DMA addresses
|
|
and to enable/disable various cards at load time. Normally
|
|
the driver uses the configuration parameters entered when compiling
|
|
and configuring the driver.
|
|
Look at Readme.linux for more info.
|
|
|
|
NOTE! This method is not normally required. You should use it only when
|
|
you have to use different configuration than normally. The sound=
|
|
command line parameter is error phrone and not recommended.
|
|
|
|
Debugging and tracing
|
|
---------------------
|
|
|
|
Modularized sound driver doesn't display messages during initialization as
|
|
the kernel compiled one does. This feature can be turned on by adding
|
|
init_trace=1 to the insmod command line.
|
|
|
|
For example:
|
|
|
|
insmod sound init_trace=1
|