freebsd-skq/sys/modules/cxgbe/t6_firmware
Navdeep Parhar 714d3ee05b cxgbe(4): Update T6, T5, and T4 firmwares to 1.16.63.0.
Changes since 1.16.26.0 for all three firmwares are listed below.  This
list was obtained from the Release Notes of the Chelsio Unified Wire
v3.5.05 release for Linux.

T6 Firmware
++++++++++++
================================================================================
Version : 1.16.63.0
Date    : 09/29/2017
================================================================================

Fixes
-----

BASE:
- Fixed a fw crash when configured traffic rate limit is less than 10kbps.
- Fixed traffic rate limiting for smaller traffic rate value.

ETH:
- Fixed 40G link failure when interface is toggled.
- Fixed adapter crash when interface is toggled during traffic.
- Fixed 25G link failure when PEER only supports consortium mode autoneg
  for 25G.
- Fixed 100G optics link failure when cable is plugged in after bringing up
  the interface.
- Enable RS FEC as default if speed is 100G.
- Fixed DCBX configuration refresh failure.

OFLD
- Fixed 0B iWARP ingress read failure.
- Fixed iWARP SRQ reuse failure.

FOiSCSI:
- Fixed vlan interface ping failure.
- Fixed target discovery failures.
- Fixed mutual chap login failure.

================================================================================
Version : 1.16.59.0
Date    : 09/05/2017
================================================================================

FIXES
-----

BASE:
- Fixed fw crash caused by MC parity error in SO adapters.
- Generate Timer0Int interrupt if fw crashes due to unaligned access error. Host
  driver must look into PCIE_FW register to see if any fw fatal error has
  encountered. If PCIE_FW doesn't indicate any error then driver must ignore this
  interrupt.
- Fixed receive buffer threshold settings which was resulting in error frames on
  receive side.

ETH:
- Fixed an issue in connection traffic shaping when
  FLOWC_WR->FW_FLOWC_MNEM_SCHEDCLASS is not received in first WR on the connection.
- Fixed link failure when speed is changed from 10G-1G-10G due to incorrect flag
  check.
- Fixed improper LED behaviour for blink test and when traffic is running.
- Removed storage of previous fec settings from fw. Driver needs to pass the user
  settings whenever a new module is plugged in as fw resets these when a module is
  unplugged.

OFLD
- OVS offload: TP cache is flushed periodically to get the accuate filters stats
  (hit count).

ENHANCEMENTS
------------

BASE:
- Ring backbone feature added. New FW_PARAMS_PARAM_DEV_RING_BACKBONE param type
  added to query and enable ring backbone support.
- VNI support added for filtering. New entry_type FW_VI_MAC_TYPE_EXACTMAC_VNI
  added to FW_VI_MAC_CMD.
- Added new API FW_PARAM_PARAM_DEV_MPSBGMAP to read the priority to buffer group
  mapping for the ports.
- FW_PARAMS_PARAM_DEV_TPCHMAP API added to read the port to channel mapping.
- HMA (Host memory access) support added. New FW_HMA_CMD and
  FW_PARAMS_PARAM_DEV_HMA_SIZE added to query and configure the HMA. It
  enables the memfree support (256 connections) for iwarp.
- PTP support enabled.

ETH:
- Added consortium mode 50G support.
- Added the ability to allow only selected speeds to be advertised during auto
  negotiation.
- Increased port capability from 16 to 32 bits to support more speeds.
  FW_PARAMS_PARAM_PFVF_PORT_CAPS32 added to query whether fw supports 16 or 32
  bit port capability.

OFLD:
- RDMA Write with immediate support added (iwarp 2.0 feature)
- FW_TLS_KEYCTX_TX_WR removed and security key management moved to driver.
- 256 offloaded connections support for iwarp on SO adapters.

iSCSI:
- New param FW_PARAMS_PARAM_DEV_PPOD_EDRAM added for iscsi ppod configuration
  in EDRAM (performance improvement).

FOiSCSI:
- iSCSI Command offload target support added.

FOFCoE:
- FCoE support enabled.

================================================================================
Version : 1.16.43.0
Date    : 05/05/2017
================================================================================

FIXES
-----

BASE:
- Fixed default DCB mode to AUTO.
- Fixed DCBX bugs when AUTO mode is configured in config file.
- Fixed an issue where even after removing PFC from switch, PFC wasn't getting
  reset.
- Fixed DDR3/DDR4 ECC errors.
- Fixed an FLR issue where FLR completion was going to host before FLR
  processing is finished in fw.

ETH:
- Fixed bug in writing multi-bytes using i2c interface.
- Fixed the link failure when optical cable is inserted into the QSA module
  after loading the driver.
- Fixed false link up when peer interface was brought down.
- Enabling RS FEC by default for 100Gbase-SR4 according to 802.3BJ standard.
- Fixed bugs related to negotiated fec based local/peer fec ability and request.
- Fixed auto-neg failure with few switches.
- T6 Performance improvement fixes.

OFLD
- Fixed an extra credit issue if FW_RI_TYPE_FINI is delayed in fw due to
  backpressure.
- Added a new queue type FW_IQ_TYPE_VF_CQ to handle the FW_PARAMS_PARAM_DMAQ*
  commands. queue type will be part of the FW_PARAMS_PARAM_DMAQ_IQ_INTIDX
  value. Used in guest RDMA (RDMA from VM/VF) usecase.
- T6 Crypto Coprocessor mode bug fixes.
- T6 Crypto TLS-inline mode bug fixes.

ENHANCEMENTS
------------

BASE:
- Added new API FW_PARAM_PARAM_DEV_MPSBGMAP to read the priority to buffer
  group mapping for the ports.

ETH:
- Added broadcom consortium next page support for 25G CR.
  This can be enabled using flags=an_brcm option in the t6-config.txt file.
- Added spider mode support.
- Added support for 10G-BaseT converter sfp+ module.
- Added support for additional 25G/100G cables.
- Added support to enable/disable auto-neg using ethtool.

================================================================================
Version : 1.16.33.0
Date    : 02/24/2017
================================================================================

Fixes
-----

BASE:
- Fixed DDR4 uncorrectable errors.

ETH:
- Enabled link auto negotiation (AN) by default in config file.
- Added AN and FEC control api. Host driver and application can enable/disable
  AN and FEC.

ENHANCEMENTS
------------

BASE:
- Enabled High priorty filter.
- Added T6425 adapter support.

ETH:
- Added new workrequest ETH_TX_PKTS2_WR (see fw api document for more details).

================================================================================
Version : 1.16.29.0
Date    : 01/27/2017
================================================================================

FIXES
-----

BASE:
- Set multiple fec values only if AN is enabled in config file and when module
  is connected.
- Fixed intermittent DDR3/4 ECC errors.
- max number of ethctrl queue in VF set to 2 (reverted the last change
  because it causes problem in VF drivers).

ETH:
- Made devlog more verbose by printing cable information in redable form.
- Updated AN settings to work with more 25G/100G switches.
- Added support for more SFP28/QSFP28 cables.
- Fixed an issue of link going down after few hours of idle time.

OFLD:
- Fixed an issue in TLS which was causing fw crash on running TLS traffic.

FOiSCSI:
- Fixed the failure of PXE boot OS install on an iscsi lun.

ENHANCEMENTS
------------

OFLD:
- Added filtering support for NAT. New WR FW_FILTER2_WR and
  FW_PARAMS_PARAM_DEV_FILTER2_WR added for the same.
- Added RDMA guest mode (mode 3 or RDMA from VF) support.

================================================================================

T5 Firmware
++++++++++++
================================================================================
Version : 1.16.63.0
Date    : 09/29/2017
================================================================================

Fixes
-----

BASE:
- Fixed offload memory overcommit in case of SO adapter.

ETH:
- Fixed DCBX configuration refresh failure.

OFLD
- Fixed 0B iWARP ingress read failure.

FOiSCSI:
- Fixed vlan interface ping failure.

================================================================================
Version : 1.16.59.0
Date    : 09/05/2017
================================================================================

FIXES
-----

BASE:
- Fixed an FLR issue which was causing error when VF attached VM was powered on.

ETH:
- Fixed an issue in connection traffic shaping when
  FLOWC_WR->FW_FLOWC_MNEM_SCHEDCLASS is not received in first WR on the connection.
- Fixed link failure when speed is changed from 10G-1G-10G due to incorrect flag
  check.
- Fixed T580 link failure with few switches which take more time for
  establishing link.

ENHANCEMENTS
------------

BASE:
- Ring backbone feature added. New FW_PARAMS_PARAM_DEV_RING_BACKBONE param type
  added to query and enable ring backbone support.
- Added new API FW_PARAM_PARAM_DEV_MPSBGMAP to read the priority to buffer group
  mapping for the ports.
- FW_PARAMS_PARAM_DEV_TPCHMAP API added to read the port to channel mapping.

FOiSCSI:
- iSCSI Command offload target support added.

================================================================================
Version : 1.16.43.0
Date    : 05/05/2017
================================================================================

FIXES
-----

BASE:
- Fixed default DCB mode to AUTO.
- Fixed DCBX bugs when AUTO mode is configured in config file.
- Fixed an issue where even after removing PFC from switch, PFC wasn't getting
  reset.

ETH:
- Fixed bug in writing multi-bytes using i2c interface.
- Fixed the link failure when optical cable is inserted into the QSA module
  after loading the driver.

OFLD
- Fixed an extra credit issue if FW_RI_TYPE_FINI is delayed in fw due to
  backpressure.
- Added a new queue type FW_IQ_TYPE_VF_CQ to handle the FW_PARAMS_PARAM_DMAQ*
  commands. queue type will be part of the FW_PARAMS_PARAM_DMAQ_IQ_INTIDX
  value. Used in guest RDMA (RDMA from VM/VF) usecase.

ENHANCEMENTS
------------

BASE:
- Added new API FW_PARAM_PARAM_DEV_MPSBGMAP to read the priority to buffer
  group mapping for the ports.

================================================================================
Version : 1.16.33.0
Date    : 02/24/2017
================================================================================

ENHANCEMENTS
------------

ETH:
- Added new workrequest ETH_TX_PKTS2_WR (see fw api document for more details).

================================================================================
Version : 1.16.29.0
Date    : 01/27/2017
================================================================================

FIXES
-----

BASE:
- max number of ethctrl queue in VF set to 2 (reverted the last change
  because it causes problem in VF drivers).

FOiSCSI:
- Fixed the failure of PXE boot OS install on an iscsi lun.

ENHANCEMENTS
------------

OFLD:
- Added filtering support for NAT. New WR FW_FILTER2_WR and
  FW_PARAMS_PARAM_DEV_FILTER2_WR added for the same.
- Added RDMA guest mode (mode 3 or RDMA from VF) support.

================================================================================

T4 Firmware
+++++++++++
================================================================================
Version : 1.16.63.0
Date    : 09/29/2017
================================================================================

Fixes
-----

ETH:
- Fixed DCBX configuration refresh failure.

FOiSCSI:
- Fixed vlan interface ping failure.

================================================================================
Version : 1.16.59.0
Date    : 09/05/2017
================================================================================

FIXES
-----

ETH:
- Fixed an issue in connection traffic shaping when
  FLOWC_WR->FW_FLOWC_MNEM_SCHEDCLASS is not received in first WR on the connection.

ENHANCEMENTS
------------

BASE:
- FW_PARAMS_PARAM_DEV_TPCHMAP API added to read the port to channel mapping.

================================================================================
Version : 1.16.43.0
Date    : 05/05/2017
================================================================================

FIXES
-----

BASE:
- Fixed default DCB mode to AUTO.
- Fixed DCBX bugs when AUTO mode is configured in config file.
- Fixed an issue where even after removing PFC from switch, PFC wasn't getting
  reset.

ETH:
- Fixed bug in writing multi-bytes using i2c interface.

OFLD
- Fixed an extra credit issue if FW_RI_TYPE_FINI is delayed in fw due to
  backpressure.
- Added a new queue type FW_IQ_TYPE_VF_CQ to handle the FW_PARAMS_PARAM_DMAQ*
  commands. queue type will be part of the FW_PARAMS_PARAM_DMAQ_IQ_INTIDX
  value. Used in guest RDMA (RDMA from VM/VF) usecase.

ENHANCEMENTS
------------

BASE:
- Added new API FW_PARAM_PARAM_DEV_MPSBGMAP to read the priority to buffer
  group mapping for the ports.

Obtained from:	Chelsio Communications
MFC after:	2 weeks
Sponsored by:	Chelsio Communications
2017-10-07 17:24:23 +00:00
..
Makefile cxgbe(4): Update T6, T5, and T4 firmwares to 1.16.63.0. 2017-10-07 17:24:23 +00:00