f8c9f3a5e2
subset ("compatible", "device_type", "model" and "name") of the standard
properties in drivers for devices on Open Firmware supported busses. The
standard properties "reg", "interrupts" und "address" are not covered by
this interface because they are only of interest in the respective bridge
code. There's a remaining standard property "status" which is unclear how
to support properly but which also isn't used in FreeBSD at present.
This ofw_bus kobj-interface allows to replace the various (ebus_get_node(),
ofw_pci_get_node(), etc.) and partially inconsistent (central_get_type()
vs. sbus_get_device_type(), etc.) existing IVAR ones with a common one.
This in turn allows to simplify and remove code-duplication in drivers for
devices that can hang off of more than one OFW supported bus.
- Convert the sparc64 Central, EBus, FHC, PCI and SBus bus drivers and the
drivers for their children to use the ofw_bus kobj-interface. The IVAR-
interfaces of the Central, EBus and FHC are entirely replaced by this. The
PCI bus driver used its own kobj-interface and now also uses the ofw_bus
one. The IVARs special to the SBus, e.g. for retrieving the burst size,
remain.
Beware: this causes an ABI-breakage for modules of drivers which used the
IVAR-interfaces, i.e. esp(4), hme(4), isp(4) and uart(4), which need to be
recompiled.
The style-inconsistencies introduced in some of the bus drivers will be
fixed by tmm@ in a generic clean-up of the respective drivers later (he
requested to add the changes in the "new" style).
- Convert the powerpc MacIO bus driver and the drivers for its children to
use the ofw_bus kobj-interface. This invloves removing the IVARs related
to the "reg" property which were unused and a leftover from the NetBSD
origini of the code. There's no ABI-breakage caused by this because none
of these driver are currently built as modules.
There are other powerpc bus drivers which can be converted to the ofw_bus
kobj-interface, e.g. the PCI bus driver, which should be done together
with converting powerpc to use the OFW PCI code from sparc64.
- Make the SBus and FHC front-end of zs(4) and the sparc64 eeprom(4) take
advantage of the ofw_bus kobj-interface and simplify them a bit.
Reviewed by: grehan, tmm
Approved by: re (scottl)
Discussed with: tmm
Tested with: Sun AX1105, AXe, Ultra 2, Ultra 60; PPC cross-build on i386
102 lines
3.0 KiB
C
102 lines
3.0 KiB
C
/*
|
|
* Copyright (c) 2003 Marcel Moolenaar
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
*
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
* documentation and/or other materials provided with the distribution.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
|
|
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
|
|
* OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
|
|
* IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
|
|
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
|
|
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
|
|
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
|
|
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
|
|
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
|
|
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
*/
|
|
|
|
#include <sys/cdefs.h>
|
|
__FBSDID("$FreeBSD$");
|
|
|
|
#include "opt_puc.h"
|
|
|
|
#include <sys/param.h>
|
|
#include <sys/systm.h>
|
|
#include <sys/kernel.h>
|
|
#include <sys/module.h>
|
|
#include <sys/bus.h>
|
|
#include <sys/conf.h>
|
|
|
|
#include <dev/ofw/ofw_bus.h>
|
|
|
|
#include <machine/bus.h>
|
|
#include <sys/rman.h>
|
|
#include <machine/resource.h>
|
|
|
|
#define PUC_ENTRAILS 1
|
|
#include <dev/puc/pucvar.h>
|
|
|
|
static int
|
|
puc_ebus_probe(device_t dev)
|
|
{
|
|
const char *nm;
|
|
|
|
nm = ofw_bus_get_name(dev);
|
|
if (!strcmp(nm, "se")) {
|
|
device_set_desc(dev, "Siemens SAB 82532 dual channel SCC");
|
|
return (0);
|
|
}
|
|
return (ENXIO);
|
|
}
|
|
|
|
static int
|
|
puc_ebus_attach(device_t dev)
|
|
{
|
|
struct puc_device_description dd;
|
|
int i;
|
|
|
|
bzero(&dd, sizeof(dd));
|
|
dd.name = device_get_desc(dev);
|
|
for (i = 0; i < 2; i++) {
|
|
dd.ports[i].type = PUC_PORT_TYPE_UART | PUC_PORT_UART_SAB82532;
|
|
dd.ports[i].bar = 0;
|
|
dd.ports[i].offset = 0x40 * i;
|
|
dd.ports[i].serialfreq = 0;
|
|
dd.ports[i].flags = 0;
|
|
}
|
|
return (puc_attach(dev, &dd));
|
|
}
|
|
|
|
static device_method_t puc_ebus_methods[] = {
|
|
/* Device interface */
|
|
DEVMETHOD(device_probe, puc_ebus_probe),
|
|
DEVMETHOD(device_attach, puc_ebus_attach),
|
|
|
|
DEVMETHOD(bus_alloc_resource, puc_alloc_resource),
|
|
DEVMETHOD(bus_release_resource, puc_release_resource),
|
|
DEVMETHOD(bus_get_resource, puc_get_resource),
|
|
DEVMETHOD(bus_read_ivar, puc_read_ivar),
|
|
DEVMETHOD(bus_setup_intr, puc_setup_intr),
|
|
DEVMETHOD(bus_teardown_intr, puc_teardown_intr),
|
|
DEVMETHOD(bus_print_child, bus_generic_print_child),
|
|
DEVMETHOD(bus_driver_added, bus_generic_driver_added),
|
|
{ 0, 0 }
|
|
};
|
|
|
|
static driver_t puc_ebus_driver = {
|
|
"puc",
|
|
puc_ebus_methods,
|
|
sizeof(struct puc_softc),
|
|
};
|
|
|
|
DRIVER_MODULE(puc, ebus, puc_ebus_driver, puc_devclass, 0, 0);
|