97 lines
4.1 KiB
Plaintext
97 lines
4.1 KiB
Plaintext
PARSE reference clock driver:
|
|
|
|
This directory contains the files making up the parser for
|
|
the parse refclock driver. For reasonably sane clocks this refclock
|
|
drivers allows a refclock implementation by just providing a
|
|
conversion routine and the appropriate NTP parameters. Refclock
|
|
support can run as low a 3k code with the parse refclock driver.
|
|
|
|
The modules in here are designed to live in two worlds. In userlevel
|
|
as part of the xntp daemon and in kernel land as part of a STREAMS module
|
|
or, if someone gets to it, as part of a line discipline. Currently only
|
|
SunOS4.x/SunOS5.x STREAMS are supported (volunteers for other vendors like HP?).
|
|
This structure means, that refclock_parse can work with or without kernel
|
|
support. Kernelsupport increases accuracy tremendingly. The current restriction
|
|
of the parse driver is that it only supports SYSV type ttys and that kernel
|
|
support is only available for Suns right now.
|
|
|
|
Three kernel modules are part of this directory. These work only on
|
|
SunOS (SunOS4 and SunOS5).
|
|
|
|
SunOS4 (aka Solaris 1.x):
|
|
parsestreams.loadable_module.o - standard parse module for SunOS 4
|
|
|
|
Both modules can be loaded via modload <modulename>.
|
|
|
|
SunOS5 (aka Solaris 2.x):
|
|
parse - auto loadable streams module
|
|
|
|
To install just drop "parse" into /kernel/strmod and
|
|
start the daemon (SunOS5 will do the rest).
|
|
|
|
The structure of the parse reference clock driver is as follows:
|
|
|
|
ntpd - contains NTP implementation and calls a reference clock
|
|
127.127.8.x which is implemented by
|
|
refclock_parse.c
|
|
- which contains several refclock decriptions. These are
|
|
selected by the x part of the refclock address.
|
|
The lower two bits specify the device to use. Thus the
|
|
value (x % 4) determines the device to open
|
|
(/dev/refclock-0 - /dev/refclock-3).
|
|
|
|
The kind of clock is selected by the mode parameter. This parameter
|
|
selects the clock type which deterimines how I/O is done,
|
|
the tty parameters and the NTP parameters.
|
|
|
|
refclock_parse operates on an abstract reference clock
|
|
that delivers time stamps and stati. Offsets and sychron-
|
|
isation information is derived from this data and passed
|
|
on to refclock_receive of xntp which uses that data for
|
|
syncronisation.
|
|
|
|
The abstract reference clock is generated by the parse*
|
|
routines. They parse the incoming data stream from the
|
|
clock and convert it to the appropriate time stamps.
|
|
The data is also mapped int the abstract clock states
|
|
POWERUP - clock has no valid phase and time code
|
|
information
|
|
|
|
NOSYNC - Time code is not confirmed, phase is probably
|
|
ok.
|
|
SYNC - Time code and phase are correct.
|
|
|
|
A clock is trusted for a certain time (type parameter) when
|
|
it leaves the SYNC state. This is derived from the
|
|
observation that quite a few clocks can still generate good
|
|
time code information when losing contact to their
|
|
synchronisation source. When the clock does not reagain
|
|
synchronisation in that trust period it will be deemed
|
|
unsynchronised until it regains synchronisation. The same
|
|
will happen if xntp sees the clock unsynchronised at
|
|
startup.
|
|
|
|
The upper bit of x specifies that all samples delivered
|
|
from the clock should be used to discipline the NTP
|
|
loopfilter. For clock with accurate once a second time
|
|
information this means big improvements for time keeping.
|
|
A prerequisite for passing on the time stamps to
|
|
the loopfilter is, that the clock is in synchronised state.
|
|
|
|
parse.c These are the general routines to parse the incoming data
|
|
stream. Usually these routines should not require
|
|
modification.
|
|
|
|
clk_*.c These files hole the conversion code for the time stamps
|
|
and the description how the time code can be parsed and
|
|
where the time stamps are to be taken.
|
|
If you want to add a new clock type this is the file
|
|
you need to write in addition to mention it in
|
|
parse_conf.c and setting up the NTP and TTY parameters
|
|
in refclock_parse.c.
|
|
|
|
Further information can be found in parse/README.parse and the various source
|
|
files.
|
|
|
|
Frank Kardel
|