431e606d74
only at address 0 which is supposed to be the only valid phy address on Marvell PHY. The more correct solution would be masking PHY address ranges allowable in PHY probe routine. Unfortunately, FreeBSD has no way to retrict the PHY address ranges or to pass special flags to PHY driver. This change assumes that PHY hardwares attached to msk(4) would be Marvell made 88E11xx PHY. With this changes the phantom phys attached on 88E8036(Yukon FE) should disappear. Reported by: Oleg Lomaka < oleg AT lomaka DOT org DOT ua > Tested by: Oleg Lomaka < oleg AT lomaka DOT org DOT ua >
2372 lines
103 KiB
C
2372 lines
103 KiB
C
/******************************************************************************
|
|
*
|
|
* Name: skgehw.h
|
|
* Project: Gigabit Ethernet Adapters, Common Modules
|
|
* Version: $Revision: 2.49 $
|
|
* Date: $Date: 2005/01/20 13:01:35 $
|
|
* Purpose: Defines and Macros for the Gigabit Ethernet Adapter Product Family
|
|
*
|
|
******************************************************************************/
|
|
|
|
/******************************************************************************
|
|
*
|
|
* LICENSE:
|
|
* Copyright (C) Marvell International Ltd. and/or its affiliates
|
|
*
|
|
* The computer program files contained in this folder ("Files")
|
|
* are provided to you under the BSD-type license terms provided
|
|
* below, and any use of such Files and any derivative works
|
|
* thereof created by you shall be governed by the following terms
|
|
* and conditions:
|
|
*
|
|
* - Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* - Redistributions in binary form must reproduce the above
|
|
* copyright notice, this list of conditions and the following
|
|
* disclaimer in the documentation and/or other materials provided
|
|
* with the distribution.
|
|
* - Neither the name of Marvell nor the names of its contributors
|
|
* may be used to endorse or promote products derived from this
|
|
* software without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
|
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
|
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
|
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
|
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
|
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
|
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
|
|
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
|
|
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
|
|
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
|
|
* OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
* /LICENSE
|
|
*
|
|
******************************************************************************/
|
|
|
|
/*-
|
|
* Copyright (c) 1997, 1998, 1999, 2000
|
|
* Bill Paul <wpaul@ctr.columbia.edu>. All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
* documentation and/or other materials provided with the distribution.
|
|
* 3. All advertising materials mentioning features or use of this software
|
|
* must display the following acknowledgement:
|
|
* This product includes software developed by Bill Paul.
|
|
* 4. Neither the name of the author nor the names of any co-contributors
|
|
* may be used to endorse or promote products derived from this software
|
|
* without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND
|
|
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
|
|
* ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD
|
|
* BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
|
|
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
|
|
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
|
|
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
|
|
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
|
|
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
|
|
* THE POSSIBILITY OF SUCH DAMAGE.
|
|
*/
|
|
|
|
/*-
|
|
* Copyright (c) 2003 Nathan L. Binkert <binkertn@umich.edu>
|
|
*
|
|
* Permission to use, copy, modify, and distribute this software for any
|
|
* purpose with or without fee is hereby granted, provided that the above
|
|
* copyright notice and this permission notice appear in all copies.
|
|
*
|
|
* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
|
|
* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
|
|
* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
|
|
* ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
|
|
* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
|
|
* ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
|
|
* OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
|
|
*/
|
|
|
|
/*$FreeBSD$*/
|
|
|
|
/*
|
|
* SysKonnect PCI vendor ID
|
|
*/
|
|
#define VENDORID_SK 0x1148
|
|
|
|
/*
|
|
* Marvell PCI vendor ID
|
|
*/
|
|
#define VENDORID_MARVELL 0x11AB
|
|
|
|
/*
|
|
* D-Link PCI vendor ID
|
|
*/
|
|
#define VENDORID_DLINK 0x1186
|
|
|
|
/*
|
|
* SysKonnect ethernet device IDs
|
|
*/
|
|
#define DEVICEID_SK_YUKON2 0x9000
|
|
#define DEVICEID_SK_YUKON2_EXPR 0x9e00
|
|
|
|
/*
|
|
* Marvell gigabit ethernet device IDs
|
|
*/
|
|
#define DEVICEID_MRVL_8021CU 0x4340
|
|
#define DEVICEID_MRVL_8022CU 0x4341
|
|
#define DEVICEID_MRVL_8061CU 0x4342
|
|
#define DEVICEID_MRVL_8062CU 0x4343
|
|
#define DEVICEID_MRVL_8021X 0x4344
|
|
#define DEVICEID_MRVL_8022X 0x4345
|
|
#define DEVICEID_MRVL_8061X 0x4346
|
|
#define DEVICEID_MRVL_8062X 0x4347
|
|
#define DEVICEID_MRVL_8035 0x4350
|
|
#define DEVICEID_MRVL_8036 0x4351
|
|
#define DEVICEID_MRVL_8038 0x4352
|
|
#define DEVICEID_MRVL_4360 0x4360
|
|
#define DEVICEID_MRVL_4361 0x4361
|
|
#define DEVICEID_MRVL_4362 0x4362
|
|
#define DEVICEID_MRVL_4363 0x4363
|
|
#define DEVICEID_MRVL_4364 0x4364
|
|
|
|
/*
|
|
* D-Link gigabit ethernet device ID
|
|
*/
|
|
#define DEVICEID_DLINK_DGE550SX 0x4001
|
|
#define DEVICEID_DLINK_DGE560T 0x4b00
|
|
|
|
#define BIT_31 (1 << 31)
|
|
#define BIT_30 (1 << 30)
|
|
#define BIT_29 (1 << 29)
|
|
#define BIT_28 (1 << 28)
|
|
#define BIT_27 (1 << 27)
|
|
#define BIT_26 (1 << 26)
|
|
#define BIT_25 (1 << 25)
|
|
#define BIT_24 (1 << 24)
|
|
#define BIT_23 (1 << 23)
|
|
#define BIT_22 (1 << 22)
|
|
#define BIT_21 (1 << 21)
|
|
#define BIT_20 (1 << 20)
|
|
#define BIT_19 (1 << 19)
|
|
#define BIT_18 (1 << 18)
|
|
#define BIT_17 (1 << 17)
|
|
#define BIT_16 (1 << 16)
|
|
#define BIT_15 (1 << 15)
|
|
#define BIT_14 (1 << 14)
|
|
#define BIT_13 (1 << 13)
|
|
#define BIT_12 (1 << 12)
|
|
#define BIT_11 (1 << 11)
|
|
#define BIT_10 (1 << 10)
|
|
#define BIT_9 (1 << 9)
|
|
#define BIT_8 (1 << 8)
|
|
#define BIT_7 (1 << 7)
|
|
#define BIT_6 (1 << 6)
|
|
#define BIT_5 (1 << 5)
|
|
#define BIT_4 (1 << 4)
|
|
#define BIT_3 (1 << 3)
|
|
#define BIT_2 (1 << 2)
|
|
#define BIT_1 (1 << 1)
|
|
#define BIT_0 (1 << 0)
|
|
|
|
#define SHIFT31(x) ((x) << 31)
|
|
#define SHIFT30(x) ((x) << 30)
|
|
#define SHIFT29(x) ((x) << 29)
|
|
#define SHIFT28(x) ((x) << 28)
|
|
#define SHIFT27(x) ((x) << 27)
|
|
#define SHIFT26(x) ((x) << 26)
|
|
#define SHIFT25(x) ((x) << 25)
|
|
#define SHIFT24(x) ((x) << 24)
|
|
#define SHIFT23(x) ((x) << 23)
|
|
#define SHIFT22(x) ((x) << 22)
|
|
#define SHIFT21(x) ((x) << 21)
|
|
#define SHIFT20(x) ((x) << 20)
|
|
#define SHIFT19(x) ((x) << 19)
|
|
#define SHIFT18(x) ((x) << 18)
|
|
#define SHIFT17(x) ((x) << 17)
|
|
#define SHIFT16(x) ((x) << 16)
|
|
#define SHIFT15(x) ((x) << 15)
|
|
#define SHIFT14(x) ((x) << 14)
|
|
#define SHIFT13(x) ((x) << 13)
|
|
#define SHIFT12(x) ((x) << 12)
|
|
#define SHIFT11(x) ((x) << 11)
|
|
#define SHIFT10(x) ((x) << 10)
|
|
#define SHIFT9(x) ((x) << 9)
|
|
#define SHIFT8(x) ((x) << 8)
|
|
#define SHIFT7(x) ((x) << 7)
|
|
#define SHIFT6(x) ((x) << 6)
|
|
#define SHIFT5(x) ((x) << 5)
|
|
#define SHIFT4(x) ((x) << 4)
|
|
#define SHIFT3(x) ((x) << 3)
|
|
#define SHIFT2(x) ((x) << 2)
|
|
#define SHIFT1(x) ((x) << 1)
|
|
#define SHIFT0(x) ((x) << 0)
|
|
|
|
/*
|
|
* PCI Configuration Space header
|
|
*/
|
|
#define PCI_BASE_1ST 0x10 /* 32 bit 1st Base address */
|
|
#define PCI_BASE_2ND 0x14 /* 32 bit 2nd Base address */
|
|
#define PCI_OUR_REG_1 0x40 /* 32 bit Our Register 1 */
|
|
#define PCI_OUR_REG_2 0x44 /* 32 bit Our Register 2 */
|
|
#define PCI_OUR_STATUS 0x7c /* 32 bit Adapter Status Register */
|
|
#define PCI_OUR_REG_3 0x80 /* 32 bit Our Register 3 */
|
|
#define PCI_OUR_REG_4 0x84 /* 32 bit Our Register 4 */
|
|
#define PCI_OUR_REG_5 0x88 /* 32 bit Our Register 5 */
|
|
|
|
/* PCI Express Capability */
|
|
#define PEX_CAP_ID 0xe0 /* 8 bit PEX Capability ID */
|
|
#define PEX_NITEM 0xe1 /* 8 bit PEX Next Item Pointer */
|
|
#define PEX_CAP_REG 0xe2 /* 16 bit PEX Capability Register */
|
|
#define PEX_DEV_CAP 0xe4 /* 32 bit PEX Device Capabilities */
|
|
#define PEX_DEV_CTRL 0xe8 /* 16 bit PEX Device Control */
|
|
#define PEX_DEV_STAT 0xea /* 16 bit PEX Device Status */
|
|
#define PEX_LNK_CAP 0xec /* 32 bit PEX Link Capabilities */
|
|
#define PEX_LNK_CTRL 0xf0 /* 16 bit PEX Link Control */
|
|
#define PEX_LNK_STAT 0xf2 /* 16 bit PEX Link Status */
|
|
|
|
/* PCI Express Extended Capabilities */
|
|
#define PEX_ADV_ERR_REP 0x100 /* 32 bit PEX Advanced Error Reporting */
|
|
#define PEX_UNC_ERR_STAT 0x104 /* 32 bit PEX Uncorr. Errors Status */
|
|
#define PEX_UNC_ERR_MASK 0x108 /* 32 bit PEX Uncorr. Errors Mask */
|
|
#define PEX_UNC_ERR_SEV 0x10c /* 32 bit PEX Uncorr. Errors Severity */
|
|
#define PEX_COR_ERR_STAT 0x110 /* 32 bit PEX Correc. Errors Status */
|
|
#define PEX_COR_ERR_MASK 0x114 /* 32 bit PEX Correc. Errors Mask */
|
|
#define PEX_ADV_ERR_CAP_C 0x118 /* 32 bit PEX Advanced Error Cap./Ctrl */
|
|
#define PEX_HEADER_LOG 0x11c /* 4x32 bit PEX Header Log Register */
|
|
|
|
/* PCI_OUR_REG_1 32 bit Our Register 1 */
|
|
#define PCI_Y2_PIG_ENA BIT_31 /* Enable Plug-in-Go (YUKON-2) */
|
|
#define PCI_Y2_DLL_DIS BIT_30 /* Disable PCI DLL (YUKON-2) */
|
|
#define PCI_Y2_PHY2_COMA BIT_29 /* Set PHY 2 to Coma Mode (YUKON-2) */
|
|
#define PCI_Y2_PHY1_COMA BIT_28 /* Set PHY 1 to Coma Mode (YUKON-2) */
|
|
#define PCI_Y2_PHY2_POWD BIT_27 /* Set PHY 2 to Power Down (YUKON-2) */
|
|
#define PCI_Y2_PHY1_POWD BIT_26 /* Set PHY 1 to Power Down (YUKON-2) */
|
|
#define PCI_DIS_BOOT BIT_24 /* Disable BOOT via ROM */
|
|
#define PCI_EN_IO BIT_23 /* Mapping to I/O space */
|
|
#define PCI_EN_FPROM BIT_22 /* Enable FLASH mapping to memory */
|
|
/* 1 = Map Flash to memory */
|
|
/* 0 = Disable addr. dec */
|
|
#define PCI_PAGESIZE (3L<<20)/* Bit 21..20: FLASH Page Size */
|
|
#define PCI_PAGE_16 (0L<<20)/* 16 k pages */
|
|
#define PCI_PAGE_32K (1L<<20)/* 32 k pages */
|
|
#define PCI_PAGE_64K (2L<<20)/* 64 k pages */
|
|
#define PCI_PAGE_128K (3L<<20)/* 128 k pages */
|
|
#define PCI_PAGEREG (7L<<16)/* Bit 18..16: Page Register */
|
|
#define PCI_PEX_LEGNAT BIT_15 /* PEX PM legacy/native mode (YUKON-2) */
|
|
#define PCI_FORCE_BE BIT_14 /* Assert all BEs on MR */
|
|
#define PCI_DIS_MRL BIT_13 /* Disable Mem Read Line */
|
|
#define PCI_DIS_MRM BIT_12 /* Disable Mem Read Multiple */
|
|
#define PCI_DIS_MWI BIT_11 /* Disable Mem Write & Invalidate */
|
|
#define PCI_DISC_CLS BIT_10 /* Disc: cacheLsz bound */
|
|
#define PCI_BURST_DIS BIT_9 /* Burst Disable */
|
|
#define PCI_DIS_PCI_CLK BIT_8 /* Disable PCI clock driving */
|
|
#define PCI_SKEW_DAS (0xfL<<4)/* Bit 7.. 4: Skew Ctrl, DAS Ext */
|
|
#define PCI_SKEW_BASE 0xfL /* Bit 3.. 0: Skew Ctrl, Base */
|
|
#define PCI_CLS_OPT BIT_3 /* Cache Line Size opt. PCI-X (YUKON-2) */
|
|
|
|
/* PCI_OUR_REG_2 32 bit Our Register 2 */
|
|
#define PCI_VPD_WR_THR (0xff<<24) /* Bit 31..24: VPD Write Threshold */
|
|
#define PCI_DEV_SEL (0x7f<<17) /* Bit 23..17: EEPROM Device Select */
|
|
#define PCI_VPD_ROM_SZ (0x07<<14) /* Bit 16..14: VPD ROM Size */
|
|
/* Bit 13..12: reserved */
|
|
#define PCI_PATCH_DIR (0x0f<<8) /* Bit 11.. 8: Ext Patches dir 3..0 */
|
|
#define PCI_PATCH_DIR_3 BIT_11
|
|
#define PCI_PATCH_DIR_2 BIT_10
|
|
#define PCI_PATCH_DIR_1 BIT_9
|
|
#define PCI_PATCH_DIR_0 BIT_8
|
|
#define PCI_EXT_PATCHS (0x0f<<4) /* Bit 7.. 4: Extended Patches 3..0 */
|
|
#define PCI_EXT_PATCH_3 BIT_7
|
|
#define PCI_EXT_PATCH_2 BIT_6
|
|
#define PCI_EXT_PATCH_1 BIT_5
|
|
#define PCI_EXT_PATCH_0 BIT_4
|
|
#define PCI_EN_DUMMY_RD BIT_3 /* Enable Dummy Read */
|
|
#define PCI_REV_DESC BIT_2 /* Reverse Desc. Bytes */
|
|
#define PCI_USEDATA64 BIT_0 /* Use 64Bit Data bus ext */
|
|
|
|
/* PCI_OUR_STATUS 32 bit Adapter Status Register (Yukon-2) */
|
|
#define PCI_OS_PCI64B BIT_31 /* Conventional PCI 64 bits Bus */
|
|
#define PCI_OS_PCIX BIT_30 /* PCI-X Bus */
|
|
#define PCI_OS_MODE_MSK (3<<28) /* Bit 29..28: PCI-X Bus Mode Mask */
|
|
#define PCI_OS_PCI66M BIT_27 /* PCI 66 MHz Bus */
|
|
#define PCI_OS_PCI_X BIT_26 /* PCI/PCI-X Bus (0 = PEX) */
|
|
#define PCI_OS_DLLE_MSK (3<<24) /* Bit 25..24: DLL Status Indication */
|
|
#define PCI_OS_DLLR_MSK (0x0f<<20) /* Bit 23..20: DLL Row Counters Values */
|
|
#define PCI_OS_DLLC_MSK (0x0f<<16) /* Bit 19..16: DLL Col. Counters Values */
|
|
|
|
#define PCI_OS_SPEED(val) ((val & PCI_OS_MODE_MSK) >> 28) /* PCI-X Speed */
|
|
/* possible values for the speed field of the register */
|
|
#define PCI_OS_SPD_PCI 0 /* PCI Conventional Bus */
|
|
#define PCI_OS_SPD_X66 1 /* PCI-X 66MHz Bus */
|
|
#define PCI_OS_SPD_X100 2 /* PCI-X 100MHz Bus */
|
|
#define PCI_OS_SPD_X133 3 /* PCI-X 133MHz Bus */
|
|
|
|
/* PCI_OUR_REG_4 32 bit Our Register 4 (Yukon-ECU only) */
|
|
#define PCI_TIMER_VALUE_MSK (0xff<<16) /* Bit 23..16: Timer Value Mask */
|
|
#define PCI_FORCE_ASPM_REQUEST BIT_15 /* Force ASPM Request (A1 only) */
|
|
#define PCI_ASPM_GPHY_LINK_DOWN BIT_14 /* GPHY Link Down (A1 only) */
|
|
#define PCI_ASPM_INT_FIFO_EMPTY BIT_13 /* Internal FIFO Empty (A1 only) */
|
|
#define PCI_ASPM_CLKRUN_REQUEST BIT_12 /* CLKRUN Request (A1 only) */
|
|
#define PCI_ASPM_FORCE_CLKREQ_ENA BIT_4 /* Force CLKREQ Enable (A1b only) */
|
|
#define PCI_ASPM_CLKREQ_PAD_CTL BIT_3 /* CLKREQ PAD Control (A1 only) */
|
|
#define PCI_ASPM_A1_MODE_SELECT BIT_2 /* A1 Mode Select (A1 only) */
|
|
#define PCI_CLK_GATE_PEX_UNIT_ENA BIT_1 /* Enable Gate PEX Unit Clock */
|
|
#define PCI_CLK_GATE_ROOT_COR_ENA BIT_0 /* Enable Gate Root Core Clock */
|
|
|
|
/* PEX_DEV_CTRL 16 bit PEX Device Control (Yukon-2) */
|
|
#define PEX_DC_MAX_RRS_MSK (7<<12) /* Bit 14..12: Max. Read Request Size */
|
|
#define PEX_DC_EN_NO_SNOOP BIT_11 /* Enable No Snoop */
|
|
#define PEX_DC_EN_AUX_POW BIT_10 /* Enable AUX Power */
|
|
#define PEX_DC_EN_PHANTOM BIT_9 /* Enable Phantom Functions */
|
|
#define PEX_DC_EN_EXT_TAG BIT_8 /* Enable Extended Tag Field */
|
|
#define PEX_DC_MAX_PLS_MSK (7<<5) /* Bit 7.. 5: Max. Payload Size Mask */
|
|
#define PEX_DC_EN_REL_ORD BIT_4 /* Enable Relaxed Ordering */
|
|
#define PEX_DC_EN_UNS_RQ_RP BIT_3 /* Enable Unsupported Request Reporting */
|
|
#define PEX_DC_EN_FAT_ER_RP BIT_2 /* Enable Fatal Error Reporting */
|
|
#define PEX_DC_EN_NFA_ER_RP BIT_1 /* Enable Non-Fatal Error Reporting */
|
|
#define PEX_DC_EN_COR_ER_RP BIT_0 /* Enable Correctable Error Reporting */
|
|
|
|
#define PEX_DC_MAX_RD_RQ_SIZE(x) (SHIFT12(x) & PEX_DC_MAX_RRS_MSK)
|
|
|
|
/* PEX_LNK_STAT 16 bit PEX Link Status (Yukon-2) */
|
|
#define PEX_LS_SLOT_CLK_CFG BIT_12 /* Slot Clock Config */
|
|
#define PEX_LS_LINK_TRAIN BIT_11 /* Link Training */
|
|
#define PEX_LS_TRAIN_ERROR BIT_10 /* Training Error */
|
|
#define PEX_LS_LINK_WI_MSK (0x3f<<4) /* Bit 9.. 4: Neg. Link Width Mask */
|
|
#define PEX_LS_LINK_SP_MSK 0x0f /* Bit 3.. 0: Link Speed Mask */
|
|
|
|
/* PEX_UNC_ERR_STAT PEX Uncorrectable Errors Status Register (Yukon-2) */
|
|
#define PEX_UNSUP_REQ BIT_20 /* Unsupported Request Error */
|
|
#define PEX_MALFOR_TLP BIT_18 /* Malformed TLP */
|
|
#define PEX_RX_OV BIT_17 /* Receiver Overflow (not supported) */
|
|
#define PEX_UNEXP_COMP BIT_16 /* Unexpected Completion */
|
|
#define PEX_COMP_TO BIT_14 /* Completion Timeout */
|
|
#define PEX_FLOW_CTRL_P BIT_13 /* Flow Control Protocol Error */
|
|
#define PEX_POIS_TLP BIT_12 /* Poisoned TLP */
|
|
#define PEX_DATA_LINK_P BIT_4 /* Data Link Protocol Error */
|
|
|
|
#define PEX_FATAL_ERRORS (PEX_MALFOR_TLP | PEX_FLOW_CTRL_P | PEX_DATA_LINK_P)
|
|
|
|
/* Control Register File (Address Map) */
|
|
|
|
/*
|
|
* Bank 0
|
|
*/
|
|
#define B0_RAP 0x0000 /* 8 bit Register Address Port */
|
|
#define B0_CTST 0x0004 /* 16 bit Control/Status register */
|
|
#define B0_LED 0x0006 /* 8 Bit LED register */
|
|
#define B0_POWER_CTRL 0x0007 /* 8 Bit Power Control reg (YUKON only) */
|
|
#define B0_ISRC 0x0008 /* 32 bit Interrupt Source Register */
|
|
#define B0_IMSK 0x000c /* 32 bit Interrupt Mask Register */
|
|
#define B0_HWE_ISRC 0x0010 /* 32 bit HW Error Interrupt Src Reg */
|
|
#define B0_HWE_IMSK 0x0014 /* 32 bit HW Error Interrupt Mask Reg */
|
|
#define B0_SP_ISRC 0x0018 /* 32 bit Special Interrupt Source Reg 1 */
|
|
|
|
/* Special ISR registers (Yukon-2 only) */
|
|
#define B0_Y2_SP_ISRC2 0x001c /* 32 bit Special Interrupt Source Reg 2 */
|
|
#define B0_Y2_SP_ISRC3 0x0020 /* 32 bit Special Interrupt Source Reg 3 */
|
|
#define B0_Y2_SP_EISR 0x0024 /* 32 bit Enter ISR Reg */
|
|
#define B0_Y2_SP_LISR 0x0028 /* 32 bit Leave ISR Reg */
|
|
#define B0_Y2_SP_ICR 0x002c /* 32 bit Interrupt Control Reg */
|
|
|
|
/*
|
|
* Bank 1
|
|
* - completely empty (this is the RAP Block window)
|
|
* Note: if RAP = 1 this page is reserved
|
|
*/
|
|
|
|
/*
|
|
* Bank 2
|
|
*/
|
|
/* NA reg = 48 bit Network Address Register, 3x16 or 8x8 bit readable */
|
|
#define B2_MAC_1 0x0100 /* NA reg MAC Address 1 */
|
|
#define B2_MAC_2 0x0108 /* NA reg MAC Address 2 */
|
|
#define B2_MAC_3 0x0110 /* NA reg MAC Address 3 */
|
|
#define B2_CONN_TYP 0x0118 /* 8 bit Connector type */
|
|
#define B2_PMD_TYP 0x0119 /* 8 bit PMD type */
|
|
#define B2_MAC_CFG 0x011a /* 8 bit MAC Configuration / Chip Revision */
|
|
#define B2_CHIP_ID 0x011b /* 8 bit Chip Identification Number */
|
|
#define B2_E_0 0x011c /* 8 bit EPROM Byte 0 (ext. SRAM size */
|
|
#define B2_Y2_CLK_GATE 0x011d /* 8 bit Clock Gating (Yukon-2) */
|
|
#define B2_Y2_HW_RES 0x011e /* 8 bit HW Resources (Yukon-2) */
|
|
#define B2_E_3 0x011f /* 8 bit EPROM Byte 3 */
|
|
#define B2_Y2_CLK_CTRL 0x0120 /* 32 bit Core Clock Frequency Control */
|
|
#define B2_TI_INI 0x0130 /* 32 bit Timer Init Value */
|
|
#define B2_TI_VAL 0x0134 /* 32 bit Timer Value */
|
|
#define B2_TI_CTRL 0x0138 /* 8 bit Timer Control */
|
|
#define B2_TI_TEST 0x0139 /* 8 Bit Timer Test */
|
|
#define B2_IRQM_INI 0x0140 /* 32 bit IRQ Moderation Timer Init Reg.*/
|
|
#define B2_IRQM_VAL 0x0144 /* 32 bit IRQ Moderation Timer Value */
|
|
#define B2_IRQM_CTRL 0x0148 /* 8 bit IRQ Moderation Timer Control */
|
|
#define B2_IRQM_TEST 0x0149 /* 8 bit IRQ Moderation Timer Test */
|
|
#define B2_IRQM_MSK 0x014c /* 32 bit IRQ Moderation Mask */
|
|
#define B2_IRQM_HWE_MSK 0x0150 /* 32 bit IRQ Moderation HW Error Mask */
|
|
#define B2_TST_CTRL1 0x0158 /* 8 bit Test Control Register 1 */
|
|
#define B2_TST_CTRL2 0x0159 /* 8 bit Test Control Register 2 */
|
|
#define B2_GP_IO 0x015c /* 32 bit General Purpose I/O Register */
|
|
#define B2_I2C_CTRL 0x0160 /* 32 bit I2C HW Control Register */
|
|
#define B2_I2C_DATA 0x0164 /* 32 bit I2C HW Data Register */
|
|
#define B2_I2C_IRQ 0x0168 /* 32 bit I2C HW IRQ Register */
|
|
#define B2_I2C_SW 0x016c /* 32 bit I2C SW Port Register */
|
|
|
|
#define Y2_PEX_PHY_DATA 0x0170 /* 16 bit PEX PHY Data Register */
|
|
#define Y2_PEX_PHY_ADDR 0x0172 /* 16 bit PEX PHY Address Register */
|
|
|
|
/*
|
|
* Bank 3
|
|
*/
|
|
/* RAM Random Registers */
|
|
#define B3_RAM_ADDR 0x0180 /* 32 bit RAM Address, to read or write */
|
|
#define B3_RAM_DATA_LO 0x0184 /* 32 bit RAM Data Word (low dWord) */
|
|
#define B3_RAM_DATA_HI 0x0188 /* 32 bit RAM Data Word (high dWord) */
|
|
|
|
#define SELECT_RAM_BUFFER(rb, addr) (addr | (rb << 6)) /* Yukon-2 only */
|
|
|
|
/* RAM Interface Registers */
|
|
/* Yukon-2: use SELECT_RAM_BUFFER() to access the RAM buffer */
|
|
/*
|
|
* The HW-Spec. calls this registers Timeout Value 0..11. But this names are
|
|
* not usable in SW. Please notice these are NOT real timeouts, these are
|
|
* the number of qWords transferred continuously.
|
|
*/
|
|
#define B3_RI_WTO_R1 0x0190 /* 8 bit WR Timeout Queue R1 (TO0) */
|
|
#define B3_RI_WTO_XA1 0x0191 /* 8 bit WR Timeout Queue XA1 (TO1) */
|
|
#define B3_RI_WTO_XS1 0x0192 /* 8 bit WR Timeout Queue XS1 (TO2) */
|
|
#define B3_RI_RTO_R1 0x0193 /* 8 bit RD Timeout Queue R1 (TO3) */
|
|
#define B3_RI_RTO_XA1 0x0194 /* 8 bit RD Timeout Queue XA1 (TO4) */
|
|
#define B3_RI_RTO_XS1 0x0195 /* 8 bit RD Timeout Queue XS1 (TO5) */
|
|
#define B3_RI_WTO_R2 0x0196 /* 8 bit WR Timeout Queue R2 (TO6) */
|
|
#define B3_RI_WTO_XA2 0x0197 /* 8 bit WR Timeout Queue XA2 (TO7) */
|
|
#define B3_RI_WTO_XS2 0x0198 /* 8 bit WR Timeout Queue XS2 (TO8) */
|
|
#define B3_RI_RTO_R2 0x0199 /* 8 bit RD Timeout Queue R2 (TO9) */
|
|
#define B3_RI_RTO_XA2 0x019a /* 8 bit RD Timeout Queue XA2 (TO10)*/
|
|
#define B3_RI_RTO_XS2 0x019b /* 8 bit RD Timeout Queue XS2 (TO11)*/
|
|
#define B3_RI_TO_VAL 0x019c /* 8 bit Current Timeout Count Val */
|
|
#define B3_RI_CTRL 0x01a0 /* 16 bit RAM Interface Control Register */
|
|
#define B3_RI_TEST 0x01a2 /* 8 bit RAM Interface Test Register */
|
|
|
|
/*
|
|
* Bank 4 - 5
|
|
*/
|
|
/* Transmit Arbiter Registers MAC 1 and 2, use MR_ADDR() to access */
|
|
#define TXA_ITI_INI 0x0200 /* 32 bit Tx Arb Interval Timer Init Val*/
|
|
#define TXA_ITI_VAL 0x0204 /* 32 bit Tx Arb Interval Timer Value */
|
|
#define TXA_LIM_INI 0x0208 /* 32 bit Tx Arb Limit Counter Init Val */
|
|
#define TXA_LIM_VAL 0x020c /* 32 bit Tx Arb Limit Counter Value */
|
|
#define TXA_CTRL 0x0210 /* 8 bit Tx Arbiter Control Register */
|
|
#define TXA_TEST 0x0211 /* 8 bit Tx Arbiter Test Register */
|
|
#define TXA_STAT 0x0212 /* 8 bit Tx Arbiter Status Register */
|
|
|
|
#define MR_ADDR(Mac, Offs) (((Mac) << 7) + (Offs))
|
|
|
|
/* RSS key registers for Yukon-2 Family */
|
|
#define B4_RSS_KEY 0x0220 /* 4x32 bit RSS Key register (Yukon-2) */
|
|
/* RSS key register offsets */
|
|
#define KEY_IDX_0 0 /* offset for location of KEY 0 */
|
|
#define KEY_IDX_1 4 /* offset for location of KEY 1 */
|
|
#define KEY_IDX_2 8 /* offset for location of KEY 2 */
|
|
#define KEY_IDX_3 12 /* offset for location of KEY 3 */
|
|
/* 0x0280 - 0x0292: MAC 2 */
|
|
#define RSS_KEY_ADDR(Port, KeyIndex) \
|
|
((B4_RSS_KEY | ( ((Port) == 0) ? 0 : 0x80)) + (KeyIndex))
|
|
|
|
/*
|
|
* Bank 8 - 15
|
|
*/
|
|
/* Receive and Transmit Queue Registers, use Q_ADDR() to access */
|
|
#define B8_Q_REGS 0x0400
|
|
|
|
/* Queue Register Offsets, use Q_ADDR() to access */
|
|
#define Q_D 0x00 /* 8*32 bit Current Descriptor */
|
|
#define Q_DA_L 0x20 /* 32 bit Current Descriptor Address Low dWord */
|
|
#define Q_DONE 0x24 /* 16 bit Done Index */
|
|
#define Q_AC_L 0x28 /* 32 bit Current Address Counter Low dWord */
|
|
#define Q_AC_H 0x2c /* 32 bit Current Address Counter High dWord */
|
|
#define Q_BC 0x30 /* 32 bit Current Byte Counter */
|
|
#define Q_CSR 0x34 /* 32 bit BMU Control/Status Register */
|
|
#define Q_F 0x38 /* 32 bit Flag Register */
|
|
#define Q_T1 0x3c /* 32 bit Test Register 1 */
|
|
#define Q_T1_TR 0x3c /* 8 bit Test Register 1 Transfer SM */
|
|
#define Q_T1_WR 0x3d /* 8 bit Test Register 1 Write Descriptor SM */
|
|
#define Q_T1_RD 0x3e /* 8 bit Test Register 1 Read Descriptor SM */
|
|
#define Q_T1_SV 0x3f /* 8 bit Test Register 1 Supervisor SM */
|
|
#define Q_WM 0x40 /* 16 bit FIFO Watermark */
|
|
#define Q_AL 0x42 /* 8 bit FIFO Alignment */
|
|
#define Q_RSP 0x44 /* 16 bit FIFO Read Shadow Pointer */
|
|
#define Q_RSL 0x46 /* 8 bit FIFO Read Shadow Level */
|
|
#define Q_RP 0x48 /* 8 bit FIFO Read Pointer */
|
|
#define Q_RL 0x4a /* 8 bit FIFO Read Level */
|
|
#define Q_WP 0x4c /* 8 bit FIFO Write Pointer */
|
|
#define Q_WSP 0x4d /* 8 bit FIFO Write Shadow Pointer */
|
|
#define Q_WL 0x4e /* 8 bit FIFO Write Level */
|
|
#define Q_WSL 0x4f /* 8 bit FIFO Write Shadow Level */
|
|
|
|
#define Q_ADDR(Queue, Offs) (B8_Q_REGS + (Queue) + (Offs))
|
|
|
|
/* Queue Prefetch Unit Offsets, use Y2_PREF_Q_ADDR() to address */
|
|
#define Y2_B8_PREF_REGS 0x0450
|
|
|
|
#define PREF_UNIT_CTRL_REG 0x00 /* 32 bit Prefetch Control register */
|
|
#define PREF_UNIT_LAST_IDX_REG 0x04 /* 16 bit Last Index */
|
|
#define PREF_UNIT_ADDR_LOW_REG 0x08 /* 32 bit List start addr, low part */
|
|
#define PREF_UNIT_ADDR_HI_REG 0x0c /* 32 bit List start addr, high part*/
|
|
#define PREF_UNIT_GET_IDX_REG 0x10 /* 16 bit Get Index */
|
|
#define PREF_UNIT_PUT_IDX_REG 0x14 /* 16 bit Put Index */
|
|
#define PREF_UNIT_FIFO_WP_REG 0x20 /* 8 bit FIFO write pointer */
|
|
#define PREF_UNIT_FIFO_RP_REG 0x24 /* 8 bit FIFO read pointer */
|
|
#define PREF_UNIT_FIFO_WM_REG 0x28 /* 8 bit FIFO watermark */
|
|
#define PREF_UNIT_FIFO_LEV_REG 0x2c /* 8 bit FIFO level */
|
|
|
|
#define PREF_UNIT_MASK_IDX 0x0fff
|
|
|
|
#define Y2_PREF_Q_ADDR(Queue, Offs) (Y2_B8_PREF_REGS + (Queue) + (Offs))
|
|
|
|
/*
|
|
* Bank 16 - 23
|
|
*/
|
|
/* RAM Buffer Registers */
|
|
#define B16_RAM_REGS 0x0800
|
|
|
|
/* RAM Buffer Register Offsets, use RB_ADDR() to access */
|
|
#define RB_START 0x00 /* 32 bit RAM Buffer Start Address */
|
|
#define RB_END 0x04 /* 32 bit RAM Buffer End Address */
|
|
#define RB_WP 0x08 /* 32 bit RAM Buffer Write Pointer */
|
|
#define RB_RP 0x0c /* 32 bit RAM Buffer Read Pointer */
|
|
#define RB_RX_UTPP 0x10 /* 32 bit Rx Upper Threshold, Pause Packet */
|
|
#define RB_RX_LTPP 0x14 /* 32 bit Rx Lower Threshold, Pause Packet */
|
|
#define RB_RX_UTHP 0x18 /* 32 bit Rx Upper Threshold, High Prio */
|
|
#define RB_RX_LTHP 0x1c /* 32 bit Rx Lower Threshold, High Prio */
|
|
#define RB_PC 0x20 /* 32 bit RAM Buffer Packet Counter */
|
|
#define RB_LEV 0x24 /* 32 bit RAM Buffer Level Register */
|
|
#define RB_CTRL 0x28 /* 8 bit RAM Buffer Control Register */
|
|
#define RB_TST1 0x29 /* 8 bit RAM Buffer Test Register 1 */
|
|
#define RB_TST2 0x2a /* 8 bit RAM Buffer Test Register 2 */
|
|
|
|
/*
|
|
* Bank 24
|
|
*/
|
|
/* Receive GMAC FIFO (YUKON and Yukon-2), use MR_ADDR() to access */
|
|
#define RX_GMF_EA 0x0c40 /* 32 bit Rx GMAC FIFO End Address */
|
|
#define RX_GMF_AF_THR 0x0c44 /* 32 bit Rx GMAC FIFO Almost Full Thresh. */
|
|
#define RX_GMF_CTRL_T 0x0c48 /* 32 bit Rx GMAC FIFO Control/Test */
|
|
#define RX_GMF_FL_MSK 0x0c4c /* 32 bit Rx GMAC FIFO Flush Mask */
|
|
#define RX_GMF_FL_THR 0x0c50 /* 32 bit Rx GMAC FIFO Flush Threshold */
|
|
#define RX_GMF_TR_THR 0x0c54 /* 32 bit Rx Truncation Threshold (Yukon-2) */
|
|
#define RX_GMF_UP_THR 0x0c58 /* 8 bit Rx Upper Pause Thr (Yukon-EC_U) */
|
|
#define RX_GMF_LP_THR 0x0c5a /* 8 bit Rx Lower Pause Thr (Yukon-EC_U) */
|
|
#define RX_GMF_VLAN 0x0c5c /* 32 bit Rx VLAN Type Register (Yukon-2) */
|
|
#define RX_GMF_WP 0x0c60 /* 32 bit Rx GMAC FIFO Write Pointer */
|
|
#define RX_GMF_WLEV 0x0c68 /* 32 bit Rx GMAC FIFO Write Level */
|
|
#define RX_GMF_RP 0x0c70 /* 32 bit Rx GMAC FIFO Read Pointer */
|
|
#define RX_GMF_RLEV 0x0c78 /* 32 bit Rx GMAC FIFO Read Level */
|
|
|
|
/*
|
|
* Bank 25
|
|
*/
|
|
/* 0x0c80 - 0x0cbf: MAC 2 */
|
|
/* 0x0cc0 - 0x0cff: reserved */
|
|
|
|
/*
|
|
* Bank 26
|
|
*/
|
|
/* Transmit GMAC FIFO (YUKON and Yukon-2), use MR_ADDR() to access */
|
|
#define TX_GMF_EA 0x0d40 /* 32 bit Tx GMAC FIFO End Address */
|
|
#define TX_GMF_AE_THR 0x0d44 /* 32 bit Tx GMAC FIFO Almost Empty Thresh.*/
|
|
#define TX_GMF_CTRL_T 0x0d48 /* 32 bit Tx GMAC FIFO Control/Test */
|
|
#define TX_GMF_VLAN 0x0d5c /* 32 bit Tx VLAN Type Register (Yukon-2) */
|
|
#define TX_GMF_WP 0x0d60 /* 32 bit Tx GMAC FIFO Write Pointer */
|
|
#define TX_GMF_WSP 0x0d64 /* 32 bit Tx GMAC FIFO Write Shadow Pointer */
|
|
#define TX_GMF_WLEV 0x0d68 /* 32 bit Tx GMAC FIFO Write Level */
|
|
#define TX_GMF_RP 0x0d70 /* 32 bit Tx GMAC FIFO Read Pointer */
|
|
#define TX_GMF_RSTP 0x0d74 /* 32 bit Tx GMAC FIFO Restart Pointer */
|
|
#define TX_GMF_RLEV 0x0d78 /* 32 bit Tx GMAC FIFO Read Level */
|
|
|
|
/*
|
|
* Bank 27
|
|
*/
|
|
/* 0x0d80 - 0x0dbf: MAC 2 */
|
|
/* 0x0daa - 0x0dff: reserved */
|
|
|
|
/*
|
|
* Bank 28
|
|
*/
|
|
/* Descriptor Poll Timer Registers */
|
|
#define B28_DPT_INI 0x0e00 /* 24 bit Descriptor Poll Timer Init Val */
|
|
#define B28_DPT_VAL 0x0e04 /* 24 bit Descriptor Poll Timer Curr Val */
|
|
#define B28_DPT_CTRL 0x0e08 /* 8 bit Descriptor Poll Timer Ctrl Reg */
|
|
#define B28_DPT_TST 0x0e0a /* 8 bit Descriptor Poll Timer Test Reg */
|
|
/* Time Stamp Timer Registers (YUKON only) */
|
|
#define GMAC_TI_ST_VAL 0x0e14 /* 32 bit Time Stamp Timer Curr Val */
|
|
#define GMAC_TI_ST_CTRL 0x0e18 /* 8 bit Time Stamp Timer Ctrl Reg */
|
|
#define GMAC_TI_ST_TST 0x0e1a /* 8 bit Time Stamp Timer Test Reg */
|
|
/* Polling Unit Registers (Yukon-2 only) */
|
|
#define POLL_CTRL 0x0e20 /* 32 bit Polling Unit Control Reg */
|
|
#define POLL_LAST_IDX 0x0e24 /* 16 bit Polling Unit List Last Index */
|
|
#define POLL_LIST_ADDR_LO 0x0e28 /* 32 bit Poll. List Start Addr (low) */
|
|
#define POLL_LIST_ADDR_HI 0x0e2c /* 32 bit Poll. List Start Addr (high) */
|
|
/* ASF Subsystem Registers (Yukon-2 only) */
|
|
#define B28_Y2_SMB_CONFIG 0x0e40 /* 32 bit ASF SMBus Config Register */
|
|
#define B28_Y2_SMB_CSD_REG 0x0e44 /* 32 bit ASF SMB Control/Status/Data */
|
|
#define B28_Y2_ASF_IRQ_V_BASE 0x0e60 /* 32 bit ASF IRQ Vector Base */
|
|
#define B28_Y2_ASF_STAT_CMD 0x0e68 /* 32 bit ASF Status and Command Reg */
|
|
#define B28_Y2_ASF_HOST_COM 0x0e6c /* 32 bit ASF Host Communication Reg */
|
|
#define B28_Y2_DATA_REG_1 0x0e70 /* 32 bit ASF/Host Data Register 1 */
|
|
#define B28_Y2_DATA_REG_2 0x0e74 /* 32 bit ASF/Host Data Register 2 */
|
|
#define B28_Y2_DATA_REG_3 0x0e78 /* 32 bit ASF/Host Data Register 3 */
|
|
#define B28_Y2_DATA_REG_4 0x0e7c /* 32 bit ASF/Host Data Register 4 */
|
|
|
|
/*
|
|
* Bank 29
|
|
*/
|
|
|
|
/* Status BMU Registers (Yukon-2 only)*/
|
|
#define STAT_CTRL 0x0e80 /* 32 bit Status BMU Control Reg */
|
|
#define STAT_LAST_IDX 0x0e84 /* 16 bit Status BMU Last Index */
|
|
#define STAT_LIST_ADDR_LO 0x0e88 /* 32 bit Status List Start Addr (low) */
|
|
#define STAT_LIST_ADDR_HI 0x0e8c /* 32 bit Status List Start Addr (high) */
|
|
#define STAT_TXA1_RIDX 0x0e90 /* 16 bit Status TxA1 Report Index Reg */
|
|
#define STAT_TXS1_RIDX 0x0e92 /* 16 bit Status TxS1 Report Index Reg */
|
|
#define STAT_TXA2_RIDX 0x0e94 /* 16 bit Status TxA2 Report Index Reg */
|
|
#define STAT_TXS2_RIDX 0x0e96 /* 16 bit Status TxS2 Report Index Reg */
|
|
#define STAT_TX_IDX_TH 0x0e98 /* 16 bit Status Tx Index Threshold Reg */
|
|
#define STAT_PUT_IDX 0x0e9c /* 16 bit Status Put Index Reg */
|
|
/* FIFO Control/Status Registers (Yukon-2 only)*/
|
|
#define STAT_FIFO_WP 0x0ea0 /* 8 bit Status FIFO Write Pointer Reg */
|
|
#define STAT_FIFO_RP 0x0ea4 /* 8 bit Status FIFO Read Pointer Reg */
|
|
#define STAT_FIFO_RSP 0x0ea6 /* 8 bit Status FIFO Read Shadow Ptr */
|
|
#define STAT_FIFO_LEVEL 0x0ea8 /* 8 bit Status FIFO Level Reg */
|
|
#define STAT_FIFO_SHLVL 0x0eaa /* 8 bit Status FIFO Shadow Level Reg */
|
|
#define STAT_FIFO_WM 0x0eac /* 8 bit Status FIFO Watermark Reg */
|
|
#define STAT_FIFO_ISR_WM 0x0ead /* 8 bit Status FIFO ISR Watermark Reg */
|
|
/* Level and ISR Timer Registers (Yukon-2 only)*/
|
|
#define STAT_LEV_TIMER_INI 0x0eb0 /* 32 bit Level Timer Init. Value Reg */
|
|
#define STAT_LEV_TIMER_CNT 0x0eb4 /* 32 bit Level Timer Counter Reg */
|
|
#define STAT_LEV_TIMER_CTRL 0x0eb8 /* 8 bit Level Timer Control Reg */
|
|
#define STAT_LEV_TIMER_TEST 0x0eb9 /* 8 bit Level Timer Test Reg */
|
|
#define STAT_TX_TIMER_INI 0x0ec0 /* 32 bit Tx Timer Init. Value Reg */
|
|
#define STAT_TX_TIMER_CNT 0x0ec4 /* 32 bit Tx Timer Counter Reg */
|
|
#define STAT_TX_TIMER_CTRL 0x0ec8 /* 8 bit Tx Timer Control Reg */
|
|
#define STAT_TX_TIMER_TEST 0x0ec9 /* 8 bit Tx Timer Test Reg */
|
|
#define STAT_ISR_TIMER_INI 0x0ed0 /* 32 bit ISR Timer Init. Value Reg */
|
|
#define STAT_ISR_TIMER_CNT 0x0ed4 /* 32 bit ISR Timer Counter Reg */
|
|
#define STAT_ISR_TIMER_CTRL 0x0ed8 /* 8 bit ISR Timer Control Reg */
|
|
#define STAT_ISR_TIMER_TEST 0x0ed9 /* 8 bit ISR Timer Test Reg */
|
|
|
|
#define ST_LAST_IDX_MASK 0x007f /* Last Index Mask */
|
|
#define ST_TXRP_IDX_MASK 0x0fff /* Tx Report Index Mask */
|
|
#define ST_TXTH_IDX_MASK 0x0fff /* Tx Threshold Index Mask */
|
|
#define ST_WM_IDX_MASK 0x3f /* FIFO Watermark Index Mask */
|
|
|
|
/*
|
|
* Bank 30
|
|
*/
|
|
/* GMAC and GPHY Control Registers (YUKON only) */
|
|
#define GMAC_CTRL 0x0f00 /* 32 bit GMAC Control Reg */
|
|
#define GPHY_CTRL 0x0f04 /* 32 bit GPHY Control Reg */
|
|
#define GMAC_IRQ_SRC 0x0f08 /* 8 bit GMAC Interrupt Source Reg */
|
|
#define GMAC_IRQ_MSK 0x0f0c /* 8 bit GMAC Interrupt Mask Reg */
|
|
#define GMAC_LINK_CTRL 0x0f10 /* 16 bit Link Control Reg */
|
|
|
|
/* Wake-up Frame Pattern Match Control Registers (YUKON only) */
|
|
|
|
#define WOL_REG_OFFS 0x20 /* HW-Bug: Address is + 0x20 against spec. */
|
|
|
|
#define WOL_CTRL_STAT 0x0f20 /* 16 bit WOL Control/Status Reg */
|
|
#define WOL_MATCH_CTL 0x0f22 /* 8 bit WOL Match Control Reg */
|
|
#define WOL_MATCH_RES 0x0f23 /* 8 bit WOL Match Result Reg */
|
|
#define WOL_MAC_ADDR_LO 0x0f24 /* 32 bit WOL MAC Address Low */
|
|
#define WOL_MAC_ADDR_HI 0x0f28 /* 16 bit WOL MAC Address High */
|
|
#define WOL_PATT_PME 0x0f2a /* 8 bit WOL PME Match Enable (Yukon-2) */
|
|
#define WOL_PATT_ASFM 0x0f2b /* 8 bit WOL ASF Match Enable (Yukon-2) */
|
|
#define WOL_PATT_RPTR 0x0f2c /* 8 bit WOL Pattern Read Pointer */
|
|
|
|
/* WOL Pattern Length Registers (YUKON only) */
|
|
|
|
#define WOL_PATT_LEN_LO 0x0f30 /* 32 bit WOL Pattern Length 3..0 */
|
|
#define WOL_PATT_LEN_HI 0x0f34 /* 24 bit WOL Pattern Length 6..4 */
|
|
|
|
/* WOL Pattern Counter Registers (YUKON only) */
|
|
|
|
#define WOL_PATT_CNT_0 0x0f38 /* 32 bit WOL Pattern Counter 3..0 */
|
|
#define WOL_PATT_CNT_4 0x0f3c /* 24 bit WOL Pattern Counter 6..4 */
|
|
|
|
/*
|
|
* Bank 32 - 33
|
|
*/
|
|
#define WOL_PATT_RAM_1 0x1000 /* WOL Pattern RAM Link 1 */
|
|
#define WOL_PATT_RAM_2 0x1400 /* WOL Pattern RAM Link 2 */
|
|
|
|
/* offset to configuration space on Yukon-2 */
|
|
#define Y2_CFG_SPC 0x1c00
|
|
#define BASE_GMAC_1 0x2800 /* GMAC 1 registers */
|
|
#define BASE_GMAC_2 0x3800 /* GMAC 2 registers */
|
|
|
|
/*
|
|
* Control Register Bit Definitions:
|
|
*/
|
|
/* B0_CTST 24 bit Control/Status register */
|
|
#define Y2_VMAIN_AVAIL BIT_17 /* VMAIN available (YUKON-2 only) */
|
|
#define Y2_VAUX_AVAIL BIT_16 /* VAUX available (YUKON-2 only) */
|
|
#define Y2_HW_WOL_ON BIT_15 /* HW WOL On (Yukon-EC Ultra A1 only) */
|
|
#define Y2_HW_WOL_OFF BIT_14 /* HW WOL Off (Yukon-EC Ultra A1 only) */
|
|
#define Y2_ASF_ENABLE BIT_13 /* ASF Unit Enable (YUKON-2 only) */
|
|
#define Y2_ASF_DISABLE BIT_12 /* ASF Unit Disable (YUKON-2 only) */
|
|
#define Y2_CLK_RUN_ENA BIT_11 /* CLK_RUN Enable (YUKON-2 only) */
|
|
#define Y2_CLK_RUN_DIS BIT_10 /* CLK_RUN Disable (YUKON-2 only) */
|
|
#define Y2_LED_STAT_ON BIT_9 /* Status LED On (YUKON-2 only) */
|
|
#define Y2_LED_STAT_OFF BIT_8 /* Status LED Off (YUKON-2 only) */
|
|
#define CS_ST_SW_IRQ BIT_7 /* Set IRQ SW Request */
|
|
#define CS_CL_SW_IRQ BIT_6 /* Clear IRQ SW Request */
|
|
#define CS_STOP_DONE BIT_5 /* Stop Master is finished */
|
|
#define CS_STOP_MAST BIT_4 /* Command Bit to stop the master */
|
|
#define CS_MRST_CLR BIT_3 /* Clear Master Reset */
|
|
#define CS_MRST_SET BIT_2 /* Set Master Reset */
|
|
#define CS_RST_CLR BIT_1 /* Clear Software Reset */
|
|
#define CS_RST_SET BIT_0 /* Set Software Reset */
|
|
|
|
#define LED_STAT_ON BIT_1 /* Status LED On */
|
|
#define LED_STAT_OFF BIT_0 /* Status LED Off */
|
|
|
|
/* B0_POWER_CTRL 8 Bit Power Control reg (YUKON only) */
|
|
#define PC_VAUX_ENA BIT_7 /* Switch VAUX Enable */
|
|
#define PC_VAUX_DIS BIT_6 /* Switch VAUX Disable */
|
|
#define PC_VCC_ENA BIT_5 /* Switch VCC Enable */
|
|
#define PC_VCC_DIS BIT_4 /* Switch VCC Disable */
|
|
#define PC_VAUX_ON BIT_3 /* Switch VAUX On */
|
|
#define PC_VAUX_OFF BIT_2 /* Switch VAUX Off */
|
|
#define PC_VCC_ON BIT_1 /* Switch VCC On */
|
|
#define PC_VCC_OFF BIT_0 /* Switch VCC Off */
|
|
|
|
/* B0_ISRC 32 bit Interrupt Source Register */
|
|
/* B0_IMSK 32 bit Interrupt Mask Register */
|
|
/* B0_SP_ISRC 32 bit Special Interrupt Source Reg */
|
|
/* B2_IRQM_MSK 32 bit IRQ Moderation Mask */
|
|
/* B0_Y2_SP_ISRC2 32 bit Special Interrupt Source Reg 2 */
|
|
/* B0_Y2_SP_ISRC3 32 bit Special Interrupt Source Reg 3 */
|
|
/* B0_Y2_SP_EISR 32 bit Enter ISR Reg */
|
|
/* B0_Y2_SP_LISR 32 bit Leave ISR Reg */
|
|
#define Y2_IS_PORT_MASK(Port, Mask) ((Mask) << (Port*8))
|
|
#define Y2_IS_HW_ERR BIT_31 /* Interrupt HW Error */
|
|
#define Y2_IS_STAT_BMU BIT_30 /* Status BMU Interrupt */
|
|
#define Y2_IS_ASF BIT_29 /* ASF subsystem Interrupt */
|
|
#define Y2_IS_POLL_CHK BIT_27 /* Check IRQ from polling unit */
|
|
#define Y2_IS_TWSI_RDY BIT_26 /* IRQ on end of TWSI Tx */
|
|
#define Y2_IS_IRQ_SW BIT_25 /* SW forced IRQ */
|
|
#define Y2_IS_TIMINT BIT_24 /* IRQ from Timer */
|
|
#define Y2_IS_IRQ_PHY2 BIT_12 /* Interrupt from PHY 2 */
|
|
#define Y2_IS_IRQ_MAC2 BIT_11 /* Interrupt from MAC 2 */
|
|
#define Y2_IS_CHK_RX2 BIT_10 /* Descriptor error Rx 2 */
|
|
#define Y2_IS_CHK_TXS2 BIT_9 /* Descriptor error TXS 2 */
|
|
#define Y2_IS_CHK_TXA2 BIT_8 /* Descriptor error TXA 2 */
|
|
#define Y2_IS_IRQ_PHY1 BIT_4 /* Interrupt from PHY 1 */
|
|
#define Y2_IS_IRQ_MAC1 BIT_3 /* Interrupt from MAC 1 */
|
|
#define Y2_IS_CHK_RX1 BIT_2 /* Descriptor error Rx 1 */
|
|
#define Y2_IS_CHK_TXS1 BIT_1 /* Descriptor error TXS 1 */
|
|
#define Y2_IS_CHK_TXA1 BIT_0 /* Descriptor error TXA 1 */
|
|
|
|
#define Y2_IS_L1_MASK 0x0000001f /* IRQ Mask for port 1 */
|
|
|
|
#define Y2_IS_L2_MASK 0x00001f00 /* IRQ Mask for port 2 */
|
|
|
|
#define Y2_IS_ALL_MSK 0xef001f1f /* All Interrupt bits */
|
|
|
|
#define Y2_IS_PORT_A \
|
|
(Y2_IS_IRQ_PHY1 | Y2_IS_IRQ_MAC1 | Y2_IS_CHK_TXA1 | Y2_IS_CHK_RX1)
|
|
#define Y2_IS_PORT_B \
|
|
(Y2_IS_IRQ_PHY2 | Y2_IS_IRQ_MAC2 | Y2_IS_CHK_TXA2 | Y2_IS_CHK_RX2)
|
|
|
|
/* B0_HWE_ISRC 32 bit HW Error Interrupt Src Reg */
|
|
/* B0_HWE_IMSK 32 bit HW Error Interrupt Mask Reg */
|
|
/* B2_IRQM_HWE_MSK 32 bit IRQ Moderation HW Error Mask */
|
|
#define Y2_IS_TIST_OV BIT_29 /* Time Stamp Timer overflow interrupt */
|
|
#define Y2_IS_SENSOR BIT_28 /* Sensor interrupt */
|
|
#define Y2_IS_MST_ERR BIT_27 /* Master error interrupt */
|
|
#define Y2_IS_IRQ_STAT BIT_26 /* Status exception interrupt */
|
|
#define Y2_IS_PCI_EXP BIT_25 /* PCI-Express interrupt */
|
|
#define Y2_IS_PCI_NEXP BIT_24 /* PCI-Express error similar to PCI error */
|
|
#define Y2_IS_PAR_RD2 BIT_13 /* Read RAM parity error interrupt */
|
|
#define Y2_IS_PAR_WR2 BIT_12 /* Write RAM parity error interrupt */
|
|
#define Y2_IS_PAR_MAC2 BIT_11 /* MAC hardware fault interrupt */
|
|
#define Y2_IS_PAR_RX2 BIT_10 /* Parity Error Rx Queue 2 */
|
|
#define Y2_IS_TCP_TXS2 BIT_9 /* TCP length mismatch sync Tx queue IRQ */
|
|
#define Y2_IS_TCP_TXA2 BIT_8 /* TCP length mismatch async Tx queue IRQ */
|
|
#define Y2_IS_PAR_RD1 BIT_5 /* Read RAM parity error interrupt */
|
|
#define Y2_IS_PAR_WR1 BIT_4 /* Write RAM parity error interrupt */
|
|
#define Y2_IS_PAR_MAC1 BIT_3 /* MAC hardware fault interrupt */
|
|
#define Y2_IS_PAR_RX1 BIT_2 /* Parity Error Rx Queue 1 */
|
|
#define Y2_IS_TCP_TXS1 BIT_1 /* TCP length mismatch sync Tx queue IRQ */
|
|
#define Y2_IS_TCP_TXA1 BIT_0 /* TCP length mismatch async Tx queue IRQ */
|
|
|
|
#define Y2_HWE_L1_MASK (Y2_IS_PAR_RD1 | Y2_IS_PAR_WR1 | Y2_IS_PAR_MAC1 |\
|
|
Y2_IS_PAR_RX1 | Y2_IS_TCP_TXS1| Y2_IS_TCP_TXA1)
|
|
#define Y2_HWE_L2_MASK (Y2_IS_PAR_RD2 | Y2_IS_PAR_WR2 | Y2_IS_PAR_MAC2 |\
|
|
Y2_IS_PAR_RX2 | Y2_IS_TCP_TXS2| Y2_IS_TCP_TXA2)
|
|
|
|
#define Y2_HWE_ALL_MSK (Y2_IS_TIST_OV | /* Y2_IS_SENSOR | */ Y2_IS_MST_ERR |\
|
|
Y2_IS_IRQ_STAT | Y2_IS_PCI_EXP | Y2_IS_PCI_NEXP |\
|
|
Y2_HWE_L1_MASK | Y2_HWE_L2_MASK)
|
|
|
|
/* B2_MAC_CFG 8 bit MAC Configuration / Chip Revision */
|
|
#define CFG_CHIP_R_MSK (0x0f<<4) /* Bit 7.. 4: Chip Revision */
|
|
#define CFG_DIS_M2_CLK BIT_1 /* Disable Clock for 2nd MAC */
|
|
#define CFG_SNG_MAC BIT_0 /* MAC Config: 0 = 2 MACs; 1 = 1 MAC */
|
|
|
|
/* B2_CHIP_ID 8 bit Chip Identification Number */
|
|
#define CHIP_ID_GENESIS 0x0a /* Chip ID for GENESIS */
|
|
#define CHIP_ID_YUKON 0xb0 /* Chip ID for YUKON */
|
|
#define CHIP_ID_YUKON_LITE 0xb1 /* Chip ID for YUKON-Lite (Rev. A1-A3) */
|
|
#define CHIP_ID_YUKON_LP 0xb2 /* Chip ID for YUKON-LP */
|
|
#define CHIP_ID_YUKON_XL 0xb3 /* Chip ID for YUKON-2 XL */
|
|
#define CHIP_ID_YUKON_EC_U 0xb4 /* Chip ID for YUKON-2 EC Ultra */
|
|
#define CHIP_ID_YUKON_EC 0xb6 /* Chip ID for YUKON-2 EC */
|
|
#define CHIP_ID_YUKON_FE 0xb7 /* Chip ID for YUKON-2 FE */
|
|
|
|
#define CHIP_REV_YU_XL_A0 0 /* Chip Rev. for Yukon-2 A0 */
|
|
#define CHIP_REV_YU_XL_A1 1 /* Chip Rev. for Yukon-2 A1 */
|
|
#define CHIP_REV_YU_XL_A2 2 /* Chip Rev. for Yukon-2 A2 */
|
|
#define CHIP_REV_YU_XL_A3 3 /* Chip Rev. for Yukon-2 A3 */
|
|
|
|
#define CHIP_REV_YU_EC_A1 0 /* Chip Rev. for Yukon-EC A1/A0 */
|
|
#define CHIP_REV_YU_EC_A2 1 /* Chip Rev. for Yukon-EC A2 */
|
|
#define CHIP_REV_YU_EC_A3 2 /* Chip Rev. for Yukon-EC A3 */
|
|
|
|
#define CHIP_REV_YU_EC_U_A0 1
|
|
#define CHIP_REV_YU_EC_U_A1 2
|
|
|
|
/* B2_Y2_CLK_GATE 8 bit Clock Gating (Yukon-2 only) */
|
|
#define Y2_STATUS_LNK2_INAC BIT_7 /* Status Link 2 inactiv (0 = activ) */
|
|
#define Y2_CLK_GAT_LNK2_DIS BIT_6 /* Disable clock gating Link 2 */
|
|
#define Y2_COR_CLK_LNK2_DIS BIT_5 /* Disable Core clock Link 2 */
|
|
#define Y2_PCI_CLK_LNK2_DIS BIT_4 /* Disable PCI clock Link 2 */
|
|
#define Y2_STATUS_LNK1_INAC BIT_3 /* Status Link 1 inactiv (0 = activ) */
|
|
#define Y2_CLK_GAT_LNK1_DIS BIT_2 /* Disable clock gating Link 1 */
|
|
#define Y2_COR_CLK_LNK1_DIS BIT_1 /* Disable Core clock Link 1 */
|
|
#define Y2_PCI_CLK_LNK1_DIS BIT_0 /* Disable PCI clock Link 1 */
|
|
|
|
/* B2_Y2_HW_RES 8 bit HW Resources (Yukon-2 only) */
|
|
#define CFG_LED_MODE_MSK (0x07<<2) /* Bit 4.. 2: LED Mode Mask */
|
|
#define CFG_LINK_2_AVAIL BIT_1 /* Link 2 available */
|
|
#define CFG_LINK_1_AVAIL BIT_0 /* Link 1 available */
|
|
|
|
#define CFG_LED_MODE(x) (((x) & CFG_LED_MODE_MSK) >> 2)
|
|
#define CFG_DUAL_MAC_MSK (CFG_LINK_2_AVAIL | CFG_LINK_1_AVAIL)
|
|
|
|
/* B2_E_3 8 bit lower 4 bits used for HW self test result */
|
|
#define B2_E3_RES_MASK 0x0f
|
|
|
|
/* B2_Y2_CLK_CTRL 32 bit Core Clock Frequency Control Register (Yukon-2/EC) */
|
|
/* Yukon-EC/FE */
|
|
#define Y2_CLK_DIV_VAL_MSK (0xff<<16) /* Bit 23..16: Clock Divisor Value */
|
|
#define Y2_CLK_DIV_VAL(x) (SHIFT16(x) & Y2_CLK_DIV_VAL_MSK)
|
|
/* Yukon-2 */
|
|
#define Y2_CLK_DIV_VAL2_MSK (0x07<<21) /* Bit 23..21: Clock Divisor Value */
|
|
#define Y2_CLK_SELECT2_MSK (0x1f<<16) /* Bit 20..16: Clock Select */
|
|
#define Y2_CLK_DIV_VAL_2(x) (SHIFT21(x) & Y2_CLK_DIV_VAL2_MSK)
|
|
#define Y2_CLK_SEL_VAL_2(x) (SHIFT16(x) & Y2_CLK_SELECT2_MSK)
|
|
#define Y2_CLK_DIV_ENA BIT_1 /* Enable Core Clock Division */
|
|
#define Y2_CLK_DIV_DIS BIT_0 /* Disable Core Clock Division */
|
|
|
|
/* B2_TI_CTRL 8 bit Timer control */
|
|
/* B2_IRQM_CTRL 8 bit IRQ Moderation Timer Control */
|
|
#define TIM_START BIT_2 /* Start Timer */
|
|
#define TIM_STOP BIT_1 /* Stop Timer */
|
|
#define TIM_CLR_IRQ BIT_0 /* Clear Timer IRQ (!IRQM) */
|
|
|
|
/* B2_TI_TEST 8 Bit Timer Test */
|
|
/* B2_IRQM_TEST 8 bit IRQ Moderation Timer Test */
|
|
/* B28_DPT_TST 8 bit Descriptor Poll Timer Test Reg */
|
|
#define TIM_T_ON BIT_2 /* Test mode on */
|
|
#define TIM_T_OFF BIT_1 /* Test mode off */
|
|
#define TIM_T_STEP BIT_0 /* Test step */
|
|
|
|
/* B28_DPT_INI 32 bit Descriptor Poll Timer Init Val */
|
|
/* B28_DPT_VAL 32 bit Descriptor Poll Timer Curr Val */
|
|
#define DPT_MSK 0x00ffffff /* Bit 23.. 0: Desc Poll Timer Bits */
|
|
|
|
/* B28_DPT_CTRL 8 bit Descriptor Poll Timer Ctrl Reg */
|
|
#define DPT_START BIT_1 /* Start Descriptor Poll Timer */
|
|
#define DPT_STOP BIT_0 /* Stop Descriptor Poll Timer */
|
|
|
|
/* B2_TST_CTRL1 8 bit Test Control Register 1 */
|
|
#define TST_FRC_DPERR_MR BIT_7 /* force DATAPERR on MST RD */
|
|
#define TST_FRC_DPERR_MW BIT_6 /* force DATAPERR on MST WR */
|
|
#define TST_FRC_DPERR_TR BIT_5 /* force DATAPERR on TRG RD */
|
|
#define TST_FRC_DPERR_TW BIT_4 /* force DATAPERR on TRG WR */
|
|
#define TST_FRC_APERR_M BIT_3 /* force ADDRPERR on MST */
|
|
#define TST_FRC_APERR_T BIT_2 /* force ADDRPERR on TRG */
|
|
#define TST_CFG_WRITE_ON BIT_1 /* Enable Config Reg WR */
|
|
#define TST_CFG_WRITE_OFF BIT_0 /* Disable Config Reg WR */
|
|
|
|
/* B2_I2C_CTRL 32 bit I2C HW Control Register */
|
|
#define I2C_FLAG BIT_31 /* Start read/write if WR */
|
|
#define I2C_ADDR (0x7fff<<16) /* Bit 30..16: Addr to be RD/WR */
|
|
#define I2C_DEV_SEL (0x7f<<9) /* Bit 15.. 9: I2C Device Select */
|
|
#define I2C_BURST_LEN BIT_4 /* Burst Len, 1/4 bytes */
|
|
#define I2C_DEV_SIZE (7<<1) /* Bit 3.. 1: I2C Device Size */
|
|
#define I2C_025K_DEV (0<<1) /* 0: 256 Bytes or smal. */
|
|
#define I2C_05K_DEV (1<<1) /* 1: 512 Bytes */
|
|
#define I2C_1K_DEV (2<<1) /* 2: 1024 Bytes */
|
|
#define I2C_2K_DEV (3<<1) /* 3: 2048 Bytes */
|
|
#define I2C_4K_DEV (4<<1) /* 4: 4096 Bytes */
|
|
#define I2C_8K_DEV (5<<1) /* 5: 8192 Bytes */
|
|
#define I2C_16K_DEV (6<<1) /* 6: 16384 Bytes */
|
|
#define I2C_32K_DEV (7<<1) /* 7: 32768 Bytes */
|
|
#define I2C_STOP BIT_0 /* Interrupt I2C transfer */
|
|
|
|
/* B2_I2C_IRQ 32 bit I2C HW IRQ Register */
|
|
#define I2C_CLR_IRQ BIT_0 /* Clear I2C IRQ */
|
|
|
|
/* B2_I2C_SW 32 bit (8 bit access) I2C HW SW Port Register */
|
|
#define I2C_DATA_DIR BIT_2 /* direction of I2C_DATA */
|
|
#define I2C_DATA BIT_1 /* I2C Data Port */
|
|
#define I2C_CLK BIT_0 /* I2C Clock Port */
|
|
|
|
/* I2C Address */
|
|
#define I2C_SENS_ADDR LM80_ADDR /* I2C Sensor Address (Volt and Temp) */
|
|
|
|
|
|
/* B2_BSC_CTRL 8 bit Blink Source Counter Control */
|
|
#define BSC_START BIT_1 /* Start Blink Source Counter */
|
|
#define BSC_STOP BIT_0 /* Stop Blink Source Counter */
|
|
|
|
/* B2_BSC_STAT 8 bit Blink Source Counter Status */
|
|
#define BSC_SRC BIT_0 /* Blink Source, 0=Off / 1=On */
|
|
|
|
/* B2_BSC_TST 16 bit Blink Source Counter Test Reg */
|
|
#define BSC_T_ON BIT_2 /* Test mode on */
|
|
#define BSC_T_OFF BIT_1 /* Test mode off */
|
|
#define BSC_T_STEP BIT_0 /* Test step */
|
|
|
|
/* Y2_PEX_PHY_ADDR/DATA PEX PHY address and data reg (Yukon-2 only) */
|
|
#define PEX_RD_ACCESS BIT_31 /* Access Mode Read = 1, Write = 0 */
|
|
#define PEX_DB_ACCESS BIT_30 /* Access to debug register */
|
|
|
|
/* B3_RAM_ADDR 32 bit RAM Address, to read or write */
|
|
#define RAM_ADR_RAN 0x0007ffff /* Bit 18.. 0: RAM Address Range */
|
|
|
|
/* RAM Interface Registers */
|
|
/* B3_RI_CTRL 16 bit RAM Interface Control Register */
|
|
#define RI_CLR_RD_PERR BIT_9 /* Clear IRQ RAM Read Parity Err */
|
|
#define RI_CLR_WR_PERR BIT_8 /* Clear IRQ RAM Write Parity Err */
|
|
#define RI_RST_CLR BIT_1 /* Clear RAM Interface Reset */
|
|
#define RI_RST_SET BIT_0 /* Set RAM Interface Reset */
|
|
|
|
#define MSK_RI_TO_53 36 /* RAM interface timeout */
|
|
|
|
/* Transmit Arbiter Registers MAC 1 and 2, use MR_ADDR() to access */
|
|
/* TXA_ITI_INI 32 bit Tx Arb Interval Timer Init Val */
|
|
/* TXA_ITI_VAL 32 bit Tx Arb Interval Timer Value */
|
|
/* TXA_LIM_INI 32 bit Tx Arb Limit Counter Init Val */
|
|
/* TXA_LIM_VAL 32 bit Tx Arb Limit Counter Value */
|
|
#define TXA_MAX_VAL 0x00ffffff/* Bit 23.. 0: Max TXA Timer/Cnt Val */
|
|
|
|
/* TXA_CTRL 8 bit Tx Arbiter Control Register */
|
|
#define TXA_ENA_FSYNC BIT_7 /* Enable force of sync Tx queue */
|
|
#define TXA_DIS_FSYNC BIT_6 /* Disable force of sync Tx queue */
|
|
#define TXA_ENA_ALLOC BIT_5 /* Enable alloc of free bandwidth */
|
|
#define TXA_DIS_ALLOC BIT_4 /* Disable alloc of free bandwidth */
|
|
#define TXA_START_RC BIT_3 /* Start sync Rate Control */
|
|
#define TXA_STOP_RC BIT_2 /* Stop sync Rate Control */
|
|
#define TXA_ENA_ARB BIT_1 /* Enable Tx Arbiter */
|
|
#define TXA_DIS_ARB BIT_0 /* Disable Tx Arbiter */
|
|
|
|
/* TXA_TEST 8 bit Tx Arbiter Test Register */
|
|
#define TXA_INT_T_ON BIT_5 /* Tx Arb Interval Timer Test On */
|
|
#define TXA_INT_T_OFF BIT_4 /* Tx Arb Interval Timer Test Off */
|
|
#define TXA_INT_T_STEP BIT_3 /* Tx Arb Interval Timer Step */
|
|
#define TXA_LIM_T_ON BIT_2 /* Tx Arb Limit Timer Test On */
|
|
#define TXA_LIM_T_OFF BIT_1 /* Tx Arb Limit Timer Test Off */
|
|
#define TXA_LIM_T_STEP BIT_0 /* Tx Arb Limit Timer Step */
|
|
|
|
/* TXA_STAT 8 bit Tx Arbiter Status Register */
|
|
#define TXA_PRIO_XS BIT_0 /* sync queue has prio to send */
|
|
|
|
/* Q_BC 32 bit Current Byte Counter */
|
|
#define BC_MAX 0xffff /* Bit 15.. 0: Byte counter */
|
|
|
|
/* Rx BMU Control / Status Registers (Yukon-2) */
|
|
#define BMU_IDLE BIT_31 /* BMU Idle State */
|
|
#define BMU_RX_TCP_PKT BIT_30 /* Rx TCP Packet (when RSS Hash enabled) */
|
|
#define BMU_RX_IP_PKT BIT_29 /* Rx IP Packet (when RSS Hash enabled) */
|
|
#define BMU_ENA_RX_RSS_HASH BIT_15 /* Enable Rx RSS Hash */
|
|
#define BMU_DIS_RX_RSS_HASH BIT_14 /* Disable Rx RSS Hash */
|
|
#define BMU_ENA_RX_CHKSUM BIT_13 /* Enable Rx TCP/IP Checksum Check */
|
|
#define BMU_DIS_RX_CHKSUM BIT_12 /* Disable Rx TCP/IP Checksum Check */
|
|
#define BMU_CLR_IRQ_PAR BIT_11 /* Clear IRQ on Parity errors (Rx) */
|
|
#define BMU_CLR_IRQ_TCP BIT_11 /* Clear IRQ on TCP segmen. error (Tx) */
|
|
#define BMU_CLR_IRQ_CHK BIT_10 /* Clear IRQ Check */
|
|
#define BMU_STOP BIT_9 /* Stop Rx/Tx Queue */
|
|
#define BMU_START BIT_8 /* Start Rx/Tx Queue */
|
|
#define BMU_FIFO_OP_ON BIT_7 /* FIFO Operational On */
|
|
#define BMU_FIFO_OP_OFF BIT_6 /* FIFO Operational Off */
|
|
#define BMU_FIFO_ENA BIT_5 /* Enable FIFO */
|
|
#define BMU_FIFO_RST BIT_4 /* Reset FIFO */
|
|
#define BMU_OP_ON BIT_3 /* BMU Operational On */
|
|
#define BMU_OP_OFF BIT_2 /* BMU Operational Off */
|
|
#define BMU_RST_CLR BIT_1 /* Clear BMU Reset (Enable) */
|
|
#define BMU_RST_SET BIT_0 /* Set BMU Reset */
|
|
|
|
#define BMU_CLR_RESET (BMU_FIFO_RST | BMU_OP_OFF | BMU_RST_CLR)
|
|
#define BMU_OPER_INIT (BMU_CLR_IRQ_PAR | BMU_CLR_IRQ_CHK | \
|
|
BMU_START | BMU_FIFO_ENA | BMU_OP_ON)
|
|
|
|
/* Tx BMU Control / Status Registers (Yukon-2) */
|
|
/* Bit 31: same as for Rx */
|
|
#define BMU_TX_IPIDINCR_ON BIT_13 /* Enable IP ID Increment */
|
|
#define BMU_TX_IPIDINCR_OFF BIT_12 /* Disable IP ID Increment */
|
|
#define BMU_TX_CLR_IRQ_TCP BIT_11 /* Clear IRQ on TCP segm. length mism. */
|
|
/* Bit 10..0: same as for Rx */
|
|
|
|
/* Q_F 32 bit Flag Register */
|
|
#define F_ALM_FULL BIT_27 /* Rx FIFO: almost full */
|
|
#define F_EMPTY BIT_27 /* Tx FIFO: empty flag */
|
|
#define F_FIFO_EOF BIT_26 /* Tag (EOF Flag) bit in FIFO */
|
|
#define F_WM_REACHED BIT_25 /* Watermark reached */
|
|
#define F_M_RX_RAM_DIS BIT_24 /* MAC Rx RAM Read Port disable */
|
|
#define F_FIFO_LEVEL (0x1f<<16) /* Bit 23..16: # of Qwords in FIFO */
|
|
#define F_WATER_MARK 0x0007ff /* Bit 10.. 0: Watermark */
|
|
|
|
/* Queue Prefetch Unit Offsets, use Y2_PREF_Q_ADDR() to address (Yukon-2 only)*/
|
|
/* PREF_UNIT_CTRL_REG 32 bit Prefetch Control register */
|
|
#define PREF_UNIT_OP_ON BIT_3 /* prefetch unit operational */
|
|
#define PREF_UNIT_OP_OFF BIT_2 /* prefetch unit not operational */
|
|
#define PREF_UNIT_RST_CLR BIT_1 /* Clear Prefetch Unit Reset */
|
|
#define PREF_UNIT_RST_SET BIT_0 /* Set Prefetch Unit Reset */
|
|
|
|
/* RAM Buffer Register Offsets, use RB_ADDR(Queue, Offs) to access */
|
|
/* RB_START 32 bit RAM Buffer Start Address */
|
|
/* RB_END 32 bit RAM Buffer End Address */
|
|
/* RB_WP 32 bit RAM Buffer Write Pointer */
|
|
/* RB_RP 32 bit RAM Buffer Read Pointer */
|
|
/* RB_RX_UTPP 32 bit Rx Upper Threshold, Pause Pack */
|
|
/* RB_RX_LTPP 32 bit Rx Lower Threshold, Pause Pack */
|
|
/* RB_RX_UTHP 32 bit Rx Upper Threshold, High Prio */
|
|
/* RB_RX_LTHP 32 bit Rx Lower Threshold, High Prio */
|
|
/* RB_PC 32 bit RAM Buffer Packet Counter */
|
|
/* RB_LEV 32 bit RAM Buffer Level Register */
|
|
#define RB_MSK 0x0007ffff /* Bit 18.. 0: RAM Buffer Pointer Bits */
|
|
|
|
/* RB_TST2 8 bit RAM Buffer Test Register 2 */
|
|
#define RB_PC_DEC BIT_3 /* Packet Counter Decrement */
|
|
#define RB_PC_T_ON BIT_2 /* Packet Counter Test On */
|
|
#define RB_PC_T_OFF BIT_1 /* Packet Counter Test Off */
|
|
#define RB_PC_INC BIT_0 /* Packet Counter Increment */
|
|
|
|
/* RB_TST1 8 bit RAM Buffer Test Register 1 */
|
|
#define RB_WP_T_ON BIT_6 /* Write Pointer Test On */
|
|
#define RB_WP_T_OFF BIT_5 /* Write Pointer Test Off */
|
|
#define RB_WP_INC BIT_4 /* Write Pointer Increment */
|
|
#define RB_RP_T_ON BIT_2 /* Read Pointer Test On */
|
|
#define RB_RP_T_OFF BIT_1 /* Read Pointer Test Off */
|
|
#define RB_RP_INC BIT_0 /* Read Pointer Increment */
|
|
|
|
/* RB_CTRL 8 bit RAM Buffer Control Register */
|
|
#define RB_ENA_STFWD BIT_5 /* Enable Store & Forward */
|
|
#define RB_DIS_STFWD BIT_4 /* Disable Store & Forward */
|
|
#define RB_ENA_OP_MD BIT_3 /* Enable Operation Mode */
|
|
#define RB_DIS_OP_MD BIT_2 /* Disable Operation Mode */
|
|
#define RB_RST_CLR BIT_1 /* Clear RAM Buf STM Reset */
|
|
#define RB_RST_SET BIT_0 /* Set RAM Buf STM Reset */
|
|
|
|
/* RAM Buffer High Pause Threshold values */
|
|
#define MSK_RB_ULPP (8 * 1024) /* Upper Level in kB/8 */
|
|
#define MSK_RB_LLPP_S (10 * 1024) /* Lower Level for small Queues */
|
|
#define MSK_RB_LLPP_B (16 * 1024) /* Lower Level for big Queues */
|
|
|
|
/* Threshold values for Yukon-EC Ultra */
|
|
#define MSK_ECU_ULPP 0x0080 /* Upper Pause Threshold (multiples of 8) */
|
|
#define MSK_ECU_LLPP 0x0060 /* Lower Pause Threshold (multiples of 8) */
|
|
#define MSK_ECU_AE_THR 0x0070 /* Almost Empty Threshold */
|
|
#define MSK_ECU_TXFF_LEV 0x01a0 /* Tx BMU FIFO Level */
|
|
#define MSK_ECU_JUMBO_WM 0x01
|
|
|
|
#define MSK_BMU_RX_WM 0x600 /* BMU Rx Watermark */
|
|
#define MSK_BMU_TX_WM 0x600 /* BMU Tx Watermark */
|
|
/* performance sensitive drivers should set this define to 0x80 */
|
|
#define MSK_BMU_RX_WM_PEX 0x600 /* BMU Rx Watermark for PEX */
|
|
|
|
/* Receive and Transmit Queues */
|
|
#define Q_R1 0x0000 /* Receive Queue 1 */
|
|
#define Q_R2 0x0080 /* Receive Queue 2 */
|
|
#define Q_XS1 0x0200 /* Synchronous Transmit Queue 1 */
|
|
#define Q_XA1 0x0280 /* Asynchronous Transmit Queue 1 */
|
|
#define Q_XS2 0x0300 /* Synchronous Transmit Queue 2 */
|
|
#define Q_XA2 0x0380 /* Asynchronous Transmit Queue 2 */
|
|
|
|
#define Q_ASF_R1 0x100 /* ASF Rx Queue 1 */
|
|
#define Q_ASF_R2 0x180 /* ASF Rx Queue 2 */
|
|
#define Q_ASF_T1 0x140 /* ASF Tx Queue 1 */
|
|
#define Q_ASF_T2 0x1c0 /* ASF Tx Queue 2 */
|
|
|
|
#define RB_ADDR(Queue, Offs) (B16_RAM_REGS + (Queue) + (Offs))
|
|
|
|
/* Minimum RAM Buffer Rx Queue Size */
|
|
#define MSK_MIN_RXQ_SIZE 10
|
|
/* Minimum RAM Buffer Tx Queue Size */
|
|
#define MSK_MIN_TXQ_SIZE 10
|
|
/* Percentage of queue size from whole memory. 80 % for receive */
|
|
#define MSK_RAM_QUOTA_RX 80
|
|
|
|
/* WOL_CTRL_STAT 16 bit WOL Control/Status Reg */
|
|
#define WOL_CTL_LINK_CHG_OCC BIT_15
|
|
#define WOL_CTL_MAGIC_PKT_OCC BIT_14
|
|
#define WOL_CTL_PATTERN_OCC BIT_13
|
|
#define WOL_CTL_CLEAR_RESULT BIT_12
|
|
#define WOL_CTL_ENA_PME_ON_LINK_CHG BIT_11
|
|
#define WOL_CTL_DIS_PME_ON_LINK_CHG BIT_10
|
|
#define WOL_CTL_ENA_PME_ON_MAGIC_PKT BIT_9
|
|
#define WOL_CTL_DIS_PME_ON_MAGIC_PKT BIT_8
|
|
#define WOL_CTL_ENA_PME_ON_PATTERN BIT_7
|
|
#define WOL_CTL_DIS_PME_ON_PATTERN BIT_6
|
|
#define WOL_CTL_ENA_LINK_CHG_UNIT BIT_5
|
|
#define WOL_CTL_DIS_LINK_CHG_UNIT BIT_4
|
|
#define WOL_CTL_ENA_MAGIC_PKT_UNIT BIT_3
|
|
#define WOL_CTL_DIS_MAGIC_PKT_UNIT BIT_2
|
|
#define WOL_CTL_ENA_PATTERN_UNIT BIT_1
|
|
#define WOL_CTL_DIS_PATTERN_UNIT BIT_0
|
|
|
|
#define WOL_CTL_DEFAULT \
|
|
(WOL_CTL_DIS_PME_ON_LINK_CHG | \
|
|
WOL_CTL_DIS_PME_ON_PATTERN | \
|
|
WOL_CTL_DIS_PME_ON_MAGIC_PKT | \
|
|
WOL_CTL_DIS_LINK_CHG_UNIT | \
|
|
WOL_CTL_DIS_PATTERN_UNIT | \
|
|
WOL_CTL_DIS_MAGIC_PKT_UNIT)
|
|
|
|
/* WOL_MATCH_CTL 8 bit WOL Match Control Reg */
|
|
#define WOL_CTL_PATT_ENA(x) (BIT_0 << (x))
|
|
|
|
/* WOL_PATT_PME 8 bit WOL PME Match Enable (Yukon-2) */
|
|
#define WOL_PATT_FORCE_PME BIT_7 /* Generates a PME */
|
|
#define WOL_PATT_MATCH_PME_ALL 0x7f
|
|
|
|
|
|
/*
|
|
* Marvel-PHY Registers, indirect addressed over GMAC
|
|
*/
|
|
#define PHY_MARV_CTRL 0x00 /* 16 bit r/w PHY Control Register */
|
|
#define PHY_MARV_STAT 0x01 /* 16 bit r/o PHY Status Register */
|
|
#define PHY_MARV_ID0 0x02 /* 16 bit r/o PHY ID0 Register */
|
|
#define PHY_MARV_ID1 0x03 /* 16 bit r/o PHY ID1 Register */
|
|
#define PHY_MARV_AUNE_ADV 0x04 /* 16 bit r/w Auto-Neg. Advertisement */
|
|
#define PHY_MARV_AUNE_LP 0x05 /* 16 bit r/o Link Part Ability Reg */
|
|
#define PHY_MARV_AUNE_EXP 0x06 /* 16 bit r/o Auto-Neg. Expansion Reg */
|
|
#define PHY_MARV_NEPG 0x07 /* 16 bit r/w Next Page Register */
|
|
#define PHY_MARV_NEPG_LP 0x08 /* 16 bit r/o Next Page Link Partner */
|
|
/* Marvel-specific registers */
|
|
#define PHY_MARV_1000T_CTRL 0x09 /* 16 bit r/w 1000Base-T Control Reg */
|
|
#define PHY_MARV_1000T_STAT 0x0a /* 16 bit r/o 1000Base-T Status Reg */
|
|
/* 0x0b - 0x0e: reserved */
|
|
#define PHY_MARV_EXT_STAT 0x0f /* 16 bit r/o Extended Status Reg */
|
|
#define PHY_MARV_PHY_CTRL 0x10 /* 16 bit r/w PHY Specific Control Reg */
|
|
#define PHY_MARV_PHY_STAT 0x11 /* 16 bit r/o PHY Specific Status Reg */
|
|
#define PHY_MARV_INT_MASK 0x12 /* 16 bit r/w Interrupt Mask Reg */
|
|
#define PHY_MARV_INT_STAT 0x13 /* 16 bit r/o Interrupt Status Reg */
|
|
#define PHY_MARV_EXT_CTRL 0x14 /* 16 bit r/w Ext. PHY Specific Ctrl */
|
|
#define PHY_MARV_RXE_CNT 0x15 /* 16 bit r/w Receive Error Counter */
|
|
#define PHY_MARV_EXT_ADR 0x16 /* 16 bit r/w Ext. Ad. for Cable Diag. */
|
|
#define PHY_MARV_PORT_IRQ 0x17 /* 16 bit r/o Port 0 IRQ (88E1111 only) */
|
|
#define PHY_MARV_LED_CTRL 0x18 /* 16 bit r/w LED Control Reg */
|
|
#define PHY_MARV_LED_OVER 0x19 /* 16 bit r/w Manual LED Override Reg */
|
|
#define PHY_MARV_EXT_CTRL_2 0x1a /* 16 bit r/w Ext. PHY Specific Ctrl 2 */
|
|
#define PHY_MARV_EXT_P_STAT 0x1b /* 16 bit r/w Ext. PHY Spec. Stat Reg */
|
|
#define PHY_MARV_CABLE_DIAG 0x1c /* 16 bit r/o Cable Diagnostic Reg */
|
|
#define PHY_MARV_PAGE_ADDR 0x1d /* 16 bit r/w Extended Page Address Reg */
|
|
#define PHY_MARV_PAGE_DATA 0x1e /* 16 bit r/w Extended Page Data Reg */
|
|
|
|
/* for 10/100 Fast Ethernet PHY (88E3082 only) */
|
|
#define PHY_MARV_FE_LED_PAR 0x16 /* 16 bit r/w LED Parallel Select Reg. */
|
|
#define PHY_MARV_FE_LED_SER 0x17 /* 16 bit r/w LED Stream Select S. LED */
|
|
#define PHY_MARV_FE_VCT_TX 0x1a /* 16 bit r/w VCT Reg. for TXP/N Pins */
|
|
#define PHY_MARV_FE_VCT_RX 0x1b /* 16 bit r/o VCT Reg. for RXP/N Pins */
|
|
#define PHY_MARV_FE_SPEC_2 0x1c /* 16 bit r/w Specific Control Reg. 2 */
|
|
|
|
#define PHY_CT_RESET (1<<15) /* Bit 15: (sc) clear all PHY related regs */
|
|
#define PHY_CT_LOOP (1<<14) /* Bit 14: enable Loopback over PHY */
|
|
#define PHY_CT_SPS_LSB (1<<13) /* Bit 13: Speed select, lower bit */
|
|
#define PHY_CT_ANE (1<<12) /* Bit 12: Auto-Negotiation Enabled */
|
|
#define PHY_CT_PDOWN (1<<11) /* Bit 11: Power Down Mode */
|
|
#define PHY_CT_ISOL (1<<10) /* Bit 10: Isolate Mode */
|
|
#define PHY_CT_RE_CFG (1<<9) /* Bit 9: (sc) Restart Auto-Negotiation */
|
|
#define PHY_CT_DUP_MD (1<<8) /* Bit 8: Duplex Mode */
|
|
#define PHY_CT_COL_TST (1<<7) /* Bit 7: Collision Test enabled */
|
|
#define PHY_CT_SPS_MSB (1<<6) /* Bit 6: Speed select, upper bit */
|
|
|
|
#define PHY_CT_SP1000 PHY_CT_SPS_MSB /* enable speed of 1000 Mbps */
|
|
#define PHY_CT_SP100 PHY_CT_SPS_LSB /* enable speed of 100 Mbps */
|
|
#define PHY_CT_SP10 (0) /* enable speed of 10 Mbps */
|
|
|
|
#define PHY_ST_EXT_ST (1<<8) /* Bit 8: Extended Status Present */
|
|
#define PHY_ST_PRE_SUP (1<<6) /* Bit 6: Preamble Suppression */
|
|
#define PHY_ST_AN_OVER (1<<5) /* Bit 5: Auto-Negotiation Over */
|
|
#define PHY_ST_REM_FLT (1<<4) /* Bit 4: Remote Fault Condition Occured */
|
|
#define PHY_ST_AN_CAP (1<<3) /* Bit 3: Auto-Negotiation Capability */
|
|
#define PHY_ST_LSYNC (1<<2) /* Bit 2: Link Synchronized */
|
|
#define PHY_ST_JAB_DET (1<<1) /* Bit 1: Jabber Detected */
|
|
#define PHY_ST_EXT_REG (1<<0) /* Bit 0: Extended Register available */
|
|
|
|
#define PHY_I1_OUI_MSK (0x3f<<10) /* Bit 15..10: Organization Unique ID */
|
|
#define PHY_I1_MOD_NUM (0x3f<<4) /* Bit 9.. 4: Model Number */
|
|
#define PHY_I1_REV_MSK 0xf /* Bit 3.. 0: Revision Number */
|
|
|
|
/* different Marvell PHY Ids */
|
|
#define PHY_MARV_ID0_VAL 0x0141 /* Marvell Unique Identifier */
|
|
|
|
#define PHY_MARV_ID1_B0 0x0C23 /* Yukon (PHY 88E1011) */
|
|
#define PHY_MARV_ID1_B2 0x0C25 /* Yukon-Plus (PHY 88E1011) */
|
|
#define PHY_MARV_ID1_C2 0x0CC2 /* Yukon-EC (PHY 88E1111) */
|
|
#define PHY_MARV_ID1_Y2 0x0C91 /* Yukon-2 (PHY 88E1112) */
|
|
#define PHY_MARV_ID1_FE 0x0C83 /* Yukon-FE (PHY 88E3082 Rev.A1) */
|
|
#define PHY_MARV_ID1_ECU 0x0CB0 /* Yukon-2 (PHY 88E1149 Rev.B2?) */
|
|
|
|
/***** PHY_MARV_1000T_STAT 16 bit r/o 1000Base-T Status Reg *****/
|
|
#define PHY_B_1000S_MSF (1<<15) /* Bit 15: Master/Slave Fault */
|
|
#define PHY_B_1000S_MSR (1<<14) /* Bit 14: Master/Slave Result */
|
|
#define PHY_B_1000S_LRS (1<<13) /* Bit 13: Local Receiver Status */
|
|
#define PHY_B_1000S_RRS (1<<12) /* Bit 12: Remote Receiver Status */
|
|
#define PHY_B_1000S_LP_FD (1<<11) /* Bit 11: Link Partner can FD */
|
|
#define PHY_B_1000S_LP_HD (1<<10) /* Bit 10: Link Partner can HD */
|
|
#define PHY_B_1000S_IEC 0xff /* Bit 7..0: Idle Error Count */
|
|
|
|
/***** PHY_MARV_AUNE_ADV 16 bit r/w Auto-Negotiation Advertisement *****/
|
|
/***** PHY_MARV_AUNE_LP 16 bit r/w Link Part Ability Reg *****/
|
|
#define PHY_M_AN_NXT_PG BIT_15 /* Request Next Page */
|
|
#define PHY_M_AN_ACK BIT_14 /* (ro) Acknowledge Received */
|
|
#define PHY_M_AN_RF BIT_13 /* Remote Fault */
|
|
#define PHY_M_AN_ASP BIT_11 /* Asymmetric Pause */
|
|
#define PHY_M_AN_PC BIT_10 /* MAC Pause implemented */
|
|
#define PHY_M_AN_100_T4 BIT_9 /* Not cap. 100Base-T4 (always 0) */
|
|
#define PHY_M_AN_100_FD BIT_8 /* Advertise 100Base-TX Full Duplex */
|
|
#define PHY_M_AN_100_HD BIT_7 /* Advertise 100Base-TX Half Duplex */
|
|
#define PHY_M_AN_10_FD BIT_6 /* Advertise 10Base-TX Full Duplex */
|
|
#define PHY_M_AN_10_HD BIT_5 /* Advertise 10Base-TX Half Duplex */
|
|
#define PHY_M_AN_SEL_MSK (0x1f<<4) /* Bit 4.. 0: Selector Field Mask */
|
|
|
|
/* special defines for FIBER (88E1011S only) */
|
|
#define PHY_M_AN_ASP_X BIT_8 /* Asymmetric Pause */
|
|
#define PHY_M_AN_PC_X BIT_7 /* MAC Pause implemented */
|
|
#define PHY_M_AN_1000X_AHD BIT_6 /* Advertise 10000Base-X Half Duplex */
|
|
#define PHY_M_AN_1000X_AFD BIT_5 /* Advertise 10000Base-X Full Duplex */
|
|
|
|
/* Pause Bits (PHY_M_AN_ASP_X and PHY_M_AN_PC_X) encoding */
|
|
#define PHY_M_P_NO_PAUSE_X (0<<7) /* Bit 8.. 7: no Pause Mode */
|
|
#define PHY_M_P_SYM_MD_X (1<<7) /* Bit 8.. 7: symmetric Pause Mode */
|
|
#define PHY_M_P_ASYM_MD_X (2<<7) /* Bit 8.. 7: asymmetric Pause Mode */
|
|
#define PHY_M_P_BOTH_MD_X (3<<7) /* Bit 8.. 7: both Pause Mode */
|
|
|
|
/***** PHY_MARV_1000T_CTRL 16 bit r/w 1000Base-T Control Reg *****/
|
|
#define PHY_M_1000C_TEST (7<<13) /* Bit 15..13: Test Modes */
|
|
#define PHY_M_1000C_MSE BIT_12 /* Manual Master/Slave Enable */
|
|
#define PHY_M_1000C_MSC BIT_11 /* M/S Configuration (1=Master) */
|
|
#define PHY_M_1000C_MPD BIT_10 /* Multi-Port Device */
|
|
#define PHY_M_1000C_AFD BIT_9 /* Advertise Full Duplex */
|
|
#define PHY_M_1000C_AHD BIT_8 /* Advertise Half Duplex */
|
|
|
|
/***** PHY_MARV_PHY_CTRL 16 bit r/w PHY Specific Ctrl Reg *****/
|
|
#define PHY_M_PC_TX_FFD_MSK (3<<14) /* Bit 15..14: Tx FIFO Depth Mask */
|
|
#define PHY_M_PC_RX_FFD_MSK (3<<12) /* Bit 13..12: Rx FIFO Depth Mask */
|
|
#define PHY_M_PC_ASS_CRS_TX BIT_11 /* Assert CRS on Transmit */
|
|
#define PHY_M_PC_FL_GOOD BIT_10 /* Force Link Good */
|
|
#define PHY_M_PC_EN_DET_MSK (3<<8) /* Bit 9.. 8: Energy Detect Mask */
|
|
#define PHY_M_PC_ENA_EXT_D BIT_7 /* Enable Ext. Distance (10BT) */
|
|
#define PHY_M_PC_MDIX_MSK (3<<5) /* Bit 6.. 5: MDI/MDIX Config. Mask */
|
|
#define PHY_M_PC_DIS_125CLK BIT_4 /* Disable 125 CLK */
|
|
#define PHY_M_PC_MAC_POW_UP BIT_3 /* MAC Power up */
|
|
#define PHY_M_PC_SQE_T_ENA BIT_2 /* SQE Test Enabled */
|
|
#define PHY_M_PC_POL_R_DIS BIT_1 /* Polarity Reversal Disabled */
|
|
#define PHY_M_PC_DIS_JABBER BIT_0 /* Disable Jabber */
|
|
|
|
#define PHY_M_PC_EN_DET SHIFT8(2) /* Energy Detect (Mode 1) */
|
|
#define PHY_M_PC_EN_DET_PLUS SHIFT8(3) /* Energy Detect Plus (Mode 2) */
|
|
|
|
#define PHY_M_PC_MDI_XMODE(x) (SHIFT5(x) & PHY_M_PC_MDIX_MSK)
|
|
|
|
#define PHY_M_PC_MAN_MDI 0 /* 00 = Manual MDI configuration */
|
|
#define PHY_M_PC_MAN_MDIX 1 /* 01 = Manual MDIX configuration */
|
|
#define PHY_M_PC_ENA_AUTO 3 /* 11 = Enable Automatic Crossover */
|
|
|
|
/* for Yukon-2 Gigabit Ethernet PHY (88E1112 only) */
|
|
#define PHY_M_PC_DIS_LINK_P BIT_15 /* Disable Link Pulses */
|
|
#define PHY_M_PC_DSC_MSK (7<<12) /* Bit 14..12: Downshift Counter */
|
|
#define PHY_M_PC_DOWN_S_ENA BIT_11 /* Downshift Enable */
|
|
/* !!! Errata in spec. (1 = disable) */
|
|
|
|
#define PHY_M_PC_DSC(x) (SHIFT12(x) & PHY_M_PC_DSC_MSK)
|
|
/* 000=1x; 001=2x; 010=3x; 011=4x */
|
|
/* 100=5x; 101=6x; 110=7x; 111=8x */
|
|
|
|
/* for 10/100 Fast Ethernet PHY (88E3082 only) */
|
|
#define PHY_M_PC_ENA_DTE_DT BIT_15 /* Enable Data Terminal Equ. (DTE) Detect */
|
|
#define PHY_M_PC_ENA_ENE_DT BIT_14 /* Enable Energy Detect (sense & pulse) */
|
|
#define PHY_M_PC_DIS_NLP_CK BIT_13 /* Disable Normal Link Puls (NLP) Check */
|
|
#define PHY_M_PC_ENA_LIP_NP BIT_12 /* Enable Link Partner Next Page Reg. */
|
|
#define PHY_M_PC_DIS_NLP_GN BIT_11 /* Disable Normal Link Puls Generation */
|
|
#define PHY_M_PC_DIS_SCRAMB BIT_9 /* Disable Scrambler */
|
|
#define PHY_M_PC_DIS_FEFI BIT_8 /* Disable Far End Fault Indic. (FEFI) */
|
|
#define PHY_M_PC_SH_TP_SEL BIT_6 /* Shielded Twisted Pair Select */
|
|
#define PHY_M_PC_RX_FD_MSK (3<<2) /* Bit 3.. 2: Rx FIFO Depth Mask */
|
|
|
|
/***** PHY_MARV_PHY_STAT 16 bit r/o PHY Specific Status Reg *****/
|
|
#define PHY_M_PS_SPEED_MSK (3<<14) /* Bit 15..14: Speed Mask */
|
|
#define PHY_M_PS_SPEED_1000 BIT_15 /* 10 = 1000 Mbps */
|
|
#define PHY_M_PS_SPEED_100 BIT_14 /* 01 = 100 Mbps */
|
|
#define PHY_M_PS_SPEED_10 0 /* 00 = 10 Mbps */
|
|
#define PHY_M_PS_FULL_DUP BIT_13 /* Full Duplex */
|
|
#define PHY_M_PS_PAGE_REC BIT_12 /* Page Received */
|
|
#define PHY_M_PS_SPDUP_RES BIT_11 /* Speed & Duplex Resolved */
|
|
#define PHY_M_PS_LINK_UP BIT_10 /* Link Up */
|
|
#define PHY_M_PS_CABLE_MSK (7<<7) /* Bit 9.. 7: Cable Length Mask */
|
|
#define PHY_M_PS_MDI_X_STAT BIT_6 /* MDI Crossover Stat (1=MDIX) */
|
|
#define PHY_M_PS_DOWNS_STAT BIT_5 /* Downshift Status (1=downsh.) */
|
|
#define PHY_M_PS_ENDET_STAT BIT_4 /* Energy Detect Status (1=act) */
|
|
#define PHY_M_PS_TX_P_EN BIT_3 /* Tx Pause Enabled */
|
|
#define PHY_M_PS_RX_P_EN BIT_2 /* Rx Pause Enabled */
|
|
#define PHY_M_PS_POL_REV BIT_1 /* Polarity Reversed */
|
|
#define PHY_M_PS_JABBER BIT_0 /* Jabber */
|
|
|
|
#define PHY_M_PS_PAUSE_MSK (PHY_M_PS_TX_P_EN | PHY_M_PS_RX_P_EN)
|
|
|
|
/* for 10/100 Fast Ethernet PHY (88E3082 only) */
|
|
#define PHY_M_PS_DTE_DETECT BIT_15 /* Data Terminal Equipment (DTE) Detected */
|
|
#define PHY_M_PS_RES_SPEED BIT_14 /* Resolved Speed (1=100 Mbps, 0=10 Mbps */
|
|
|
|
/***** PHY_MARV_INT_MASK 16 bit r/w Interrupt Mask Reg *****/
|
|
/***** PHY_MARV_INT_STAT 16 bit r/o Interrupt Status Reg *****/
|
|
#define PHY_M_IS_AN_ERROR BIT_15 /* Auto-Negotiation Error */
|
|
#define PHY_M_IS_LSP_CHANGE BIT_14 /* Link Speed Changed */
|
|
#define PHY_M_IS_DUP_CHANGE BIT_13 /* Duplex Mode Changed */
|
|
#define PHY_M_IS_AN_PR BIT_12 /* Page Received */
|
|
#define PHY_M_IS_AN_COMPL BIT_11 /* Auto-Negotiation Completed */
|
|
#define PHY_M_IS_LST_CHANGE BIT_10 /* Link Status Changed */
|
|
#define PHY_M_IS_SYMB_ERROR BIT_9 /* Symbol Error */
|
|
#define PHY_M_IS_FALSE_CARR BIT_8 /* False Carrier */
|
|
#define PHY_M_IS_FIFO_ERROR BIT_7 /* FIFO Overflow/Underrun Error */
|
|
#define PHY_M_IS_MDI_CHANGE BIT_6 /* MDI Crossover Changed */
|
|
#define PHY_M_IS_DOWNSH_DET BIT_5 /* Downshift Detected */
|
|
#define PHY_M_IS_END_CHANGE BIT_4 /* Energy Detect Changed */
|
|
#define PHY_M_IS_DTE_CHANGE BIT_2 /* DTE Power Det. Status Changed */
|
|
#define PHY_M_IS_POL_CHANGE BIT_1 /* Polarity Changed */
|
|
#define PHY_M_IS_JABBER BIT_0 /* Jabber */
|
|
|
|
#define PHY_M_DEF_MSK (PHY_M_IS_AN_ERROR | PHY_M_IS_AN_PR | \
|
|
PHY_M_IS_LST_CHANGE | PHY_M_IS_FIFO_ERROR)
|
|
|
|
/***** PHY_MARV_EXT_CTRL 16 bit r/w Ext. PHY Specific Ctrl *****/
|
|
#define PHY_M_EC_ENA_BC_EXT BIT_15 /* Enable Block Carr. Ext. (88E1111 only) */
|
|
#define PHY_M_EC_ENA_LIN_LB BIT_14 /* Enable Line Loopback (88E1111 only) */
|
|
#define PHY_M_EC_DIS_LINK_P BIT_12 /* Disable Link Pulses (88E1111 only) */
|
|
#define PHY_M_EC_M_DSC_MSK (3<<10) /* Bit 11..10: Master Downshift Counter */
|
|
/* (88E1011 only) */
|
|
#define PHY_M_EC_S_DSC_MSK (3<<8) /* Bit 9.. 8: Slave Downshift Counter */
|
|
/* (88E1011 only) */
|
|
#define PHY_M_EC_DSC_MSK_2 (7<<9) /* Bit 11.. 9: Downshift Counter */
|
|
/* (88E1111 only) */
|
|
#define PHY_M_EC_DOWN_S_ENA BIT_8 /* Downshift Enable (88E1111 only) */
|
|
/* !!! Errata in spec. (1 = disable) */
|
|
#define PHY_M_EC_RX_TIM_CT BIT_7 /* RGMII Rx Timing Control*/
|
|
#define PHY_M_EC_MAC_S_MSK (7<<4) /* Bit 6.. 4: Def. MAC interface speed */
|
|
#define PHY_M_EC_FIB_AN_ENA BIT_3 /* Fiber Auto-Neg. Enable (88E1011S only) */
|
|
#define PHY_M_EC_DTE_D_ENA BIT_2 /* DTE Detect Enable (88E1111 only) */
|
|
#define PHY_M_EC_TX_TIM_CT BIT_1 /* RGMII Tx Timing Control */
|
|
#define PHY_M_EC_TRANS_DIS BIT_0 /* Transmitter Disable (88E1111 only) */
|
|
|
|
#define PHY_M_EC_M_DSC(x) (SHIFT10(x) & PHY_M_EC_M_DSC_MSK)
|
|
/* 00=1x; 01=2x; 10=3x; 11=4x */
|
|
#define PHY_M_EC_S_DSC(x) (SHIFT8(x) & PHY_M_EC_S_DSC_MSK)
|
|
/* 00=dis; 01=1x; 10=2x; 11=3x */
|
|
#define PHY_M_EC_MAC_S(x) (SHIFT4(x) & PHY_M_EC_MAC_S_MSK)
|
|
/* 01X=0; 110=2.5; 111=25 (MHz) */
|
|
|
|
#define PHY_M_EC_DSC_2(x) (SHIFT9(x) & PHY_M_EC_DSC_MSK_2)
|
|
/* 000=1x; 001=2x; 010=3x; 011=4x */
|
|
/* 100=5x; 101=6x; 110=7x; 111=8x */
|
|
#define MAC_TX_CLK_0_MHZ 2
|
|
#define MAC_TX_CLK_2_5_MHZ 6
|
|
#define MAC_TX_CLK_25_MHZ 7
|
|
|
|
/***** PHY_MARV_LED_CTRL 16 bit r/w LED Control Reg *****/
|
|
#define PHY_M_LEDC_DIS_LED BIT_15 /* Disable LED */
|
|
#define PHY_M_LEDC_PULS_MSK (7<<12) /* Bit 14..12: Pulse Stretch Mask */
|
|
#define PHY_M_LEDC_F_INT BIT_11 /* Force Interrupt */
|
|
#define PHY_M_LEDC_BL_R_MSK (7<<8) /* Bit 10.. 8: Blink Rate Mask */
|
|
#define PHY_M_LEDC_DP_C_LSB BIT_7 /* Duplex Control (LSB, 88E1111 only) */
|
|
#define PHY_M_LEDC_TX_C_LSB BIT_6 /* Tx Control (LSB, 88E1111 only) */
|
|
#define PHY_M_LEDC_LK_C_MSK (7<<3) /* Bit 5.. 3: Link Control Mask */
|
|
/* (88E1111 only) */
|
|
#define PHY_M_LEDC_LINK_MSK (3<<3) /* Bit 4.. 3: Link Control Mask */
|
|
/* (88E1011 only) */
|
|
#define PHY_M_LEDC_DP_CTRL BIT_2 /* Duplex Control */
|
|
#define PHY_M_LEDC_DP_C_MSB BIT_2 /* Duplex Control (MSB, 88E1111 only) */
|
|
#define PHY_M_LEDC_RX_CTRL BIT_1 /* Rx Activity / Link */
|
|
#define PHY_M_LEDC_TX_CTRL BIT_0 /* Tx Activity / Link */
|
|
#define PHY_M_LEDC_TX_C_MSB BIT_0 /* Tx Control (MSB, 88E1111 only) */
|
|
|
|
#define PHY_M_LED_PULS_DUR(x) (SHIFT12(x) & PHY_M_LEDC_PULS_MSK)
|
|
|
|
#define PULS_NO_STR 0 /* no pulse stretching */
|
|
#define PULS_21MS 1 /* 21 ms to 42 ms */
|
|
#define PULS_42MS 2 /* 42 ms to 84 ms */
|
|
#define PULS_84MS 3 /* 84 ms to 170 ms */
|
|
#define PULS_170MS 4 /* 170 ms to 340 ms */
|
|
#define PULS_340MS 5 /* 340 ms to 670 ms */
|
|
#define PULS_670MS 6 /* 670 ms to 1.3 s */
|
|
#define PULS_1300MS 7 /* 1.3 s to 2.7 s */
|
|
|
|
#define PHY_M_LED_BLINK_RT(x) (SHIFT8(x) & PHY_M_LEDC_BL_R_MSK)
|
|
|
|
#define BLINK_42MS 0 /* 42 ms */
|
|
#define BLINK_84MS 1 /* 84 ms */
|
|
#define BLINK_170MS 2 /* 170 ms */
|
|
#define BLINK_340MS 3 /* 340 ms */
|
|
#define BLINK_670MS 4 /* 670 ms */
|
|
|
|
/***** PHY_MARV_LED_OVER 16 bit r/w Manual LED Override Reg *****/
|
|
#define PHY_M_LED_MO_SGMII(x) SHIFT14(x) /* Bit 15..14: SGMII AN Timer */
|
|
#define PHY_M_LED_MO_DUP(x) SHIFT10(x) /* Bit 11..10: Duplex */
|
|
#define PHY_M_LED_MO_10(x) SHIFT8(x) /* Bit 9.. 8: Link 10 */
|
|
#define PHY_M_LED_MO_100(x) SHIFT6(x) /* Bit 7.. 6: Link 100 */
|
|
#define PHY_M_LED_MO_1000(x) SHIFT4(x) /* Bit 5.. 4: Link 1000 */
|
|
#define PHY_M_LED_MO_RX(x) SHIFT2(x) /* Bit 3.. 2: Rx */
|
|
#define PHY_M_LED_MO_TX(x) SHIFT0(x) /* Bit 1.. 0: Tx */
|
|
|
|
#define MO_LED_NORM 0
|
|
#define MO_LED_BLINK 1
|
|
#define MO_LED_OFF 2
|
|
#define MO_LED_ON 3
|
|
|
|
/***** PHY_MARV_EXT_CTRL_2 16 bit r/w Ext. PHY Specific Ctrl 2 *****/
|
|
#define PHY_M_EC2_FI_IMPED BIT_6 /* Fiber Input Impedance */
|
|
#define PHY_M_EC2_FO_IMPED BIT_5 /* Fiber Output Impedance */
|
|
#define PHY_M_EC2_FO_M_CLK BIT_4 /* Fiber Mode Clock Enable */
|
|
#define PHY_M_EC2_FO_BOOST BIT_3 /* Fiber Output Boost */
|
|
#define PHY_M_EC2_FO_AM_MSK 7 /* Bit 2.. 0: Fiber Output Amplitude */
|
|
|
|
/***** PHY_MARV_EXT_P_STAT 16 bit r/w Ext. PHY Specific Status *****/
|
|
#define PHY_M_FC_AUTO_SEL BIT_15 /* Fiber/Copper Auto Sel. Dis. */
|
|
#define PHY_M_FC_AN_REG_ACC BIT_14 /* Fiber/Copper AN Reg. Access */
|
|
#define PHY_M_FC_RESOLUTION BIT_13 /* Fiber/Copper Resolution */
|
|
#define PHY_M_SER_IF_AN_BP BIT_12 /* Ser. IF AN Bypass Enable */
|
|
#define PHY_M_SER_IF_BP_ST BIT_11 /* Ser. IF AN Bypass Status */
|
|
#define PHY_M_IRQ_POLARITY BIT_10 /* IRQ polarity */
|
|
#define PHY_M_DIS_AUT_MED BIT_9 /* Disable Aut. Medium Reg. Selection */
|
|
/* (88E1111 only) */
|
|
#define PHY_M_UNDOC1 BIT_7 /* undocumented bit !! */
|
|
#define PHY_M_DTE_POW_STAT BIT_4 /* DTE Power Status (88E1111 only) */
|
|
#define PHY_M_MODE_MASK 0xf /* Bit 3.. 0: copy of HWCFG MODE[3:0] */
|
|
|
|
/***** PHY_MARV_CABLE_DIAG 16 bit r/o Cable Diagnostic Reg *****/
|
|
#define PHY_M_CABD_ENA_TEST BIT_15 /* Enable Test (Page 0) */
|
|
#define PHY_M_CABD_DIS_WAIT BIT_15 /* Disable Waiting Period (Page 1) */
|
|
/* (88E1111 only) */
|
|
#define PHY_M_CABD_STAT_MSK (3<<13) /* Bit 14..13: Status Mask */
|
|
#define PHY_M_CABD_AMPL_MSK (0x1f<<8) /* Bit 12.. 8: Amplitude Mask */
|
|
/* (88E1111 only) */
|
|
#define PHY_M_CABD_DIST_MSK 0xff /* Bit 7.. 0: Distance Mask */
|
|
|
|
/* values for Cable Diagnostic Status (11=fail; 00=OK; 10=open; 01=short) */
|
|
#define CABD_STAT_NORMAL 0
|
|
#define CABD_STAT_SHORT 1
|
|
#define CABD_STAT_OPEN 2
|
|
#define CABD_STAT_FAIL 3
|
|
|
|
/* for 10/100 Fast Ethernet PHY (88E3082 only) */
|
|
/***** PHY_MARV_FE_LED_PAR 16 bit r/w LED Parallel Select Reg. *****/
|
|
#define PHY_M_FELP_LED2_MSK (0xf<<8) /* Bit 11.. 8: LED2 Mask (LINK) */
|
|
#define PHY_M_FELP_LED1_MSK (0xf<<4) /* Bit 7.. 4: LED1 Mask (ACT) */
|
|
#define PHY_M_FELP_LED0_MSK 0xf /* Bit 3.. 0: LED0 Mask (SPEED) */
|
|
|
|
#define PHY_M_FELP_LED2_CTRL(x) (SHIFT8(x) & PHY_M_FELP_LED2_MSK)
|
|
#define PHY_M_FELP_LED1_CTRL(x) (SHIFT4(x) & PHY_M_FELP_LED1_MSK)
|
|
#define PHY_M_FELP_LED0_CTRL(x) (SHIFT0(x) & PHY_M_FELP_LED0_MSK)
|
|
|
|
#define LED_PAR_CTRL_COLX 0x00
|
|
#define LED_PAR_CTRL_ERROR 0x01
|
|
#define LED_PAR_CTRL_DUPLEX 0x02
|
|
#define LED_PAR_CTRL_DP_COL 0x03
|
|
#define LED_PAR_CTRL_SPEED 0x04
|
|
#define LED_PAR_CTRL_LINK 0x05
|
|
#define LED_PAR_CTRL_TX 0x06
|
|
#define LED_PAR_CTRL_RX 0x07
|
|
#define LED_PAR_CTRL_ACT 0x08
|
|
#define LED_PAR_CTRL_LNK_RX 0x09
|
|
#define LED_PAR_CTRL_LNK_AC 0x0a
|
|
#define LED_PAR_CTRL_ACT_BL 0x0b
|
|
#define LED_PAR_CTRL_TX_BL 0x0c
|
|
#define LED_PAR_CTRL_RX_BL 0x0d
|
|
#define LED_PAR_CTRL_COL_BL 0x0e
|
|
#define LED_PAR_CTRL_INACT 0x0f
|
|
|
|
/***** PHY_MARV_FE_SPEC_2 16 bit r/w Specific Control Reg. 2 *****/
|
|
#define PHY_M_FESC_DIS_WAIT BIT_2 /* Disable TDR Waiting Period */
|
|
#define PHY_M_FESC_ENA_MCLK BIT_1 /* Enable MAC Rx Clock in sleep mode */
|
|
#define PHY_M_FESC_SEL_CL_A BIT_0 /* Select Class A driver (100B-TX) */
|
|
|
|
/* for Yukon-2 Gigabit Ethernet PHY (88E1112 only) */
|
|
/***** PHY_MARV_PHY_CTRL (page 1) 16 bit r/w Fiber Specific Ctrl *****/
|
|
#define PHY_M_FIB_FORCE_LNK BIT_10 /* Force Link Good */
|
|
#define PHY_M_FIB_SIGD_POL BIT_9 /* SIGDET Polarity */
|
|
#define PHY_M_FIB_TX_DIS BIT_3 /* Transmitter Disable */
|
|
|
|
/***** PHY_MARV_PHY_CTRL (page 2) 16 bit r/w MAC Specific Ctrl *****/
|
|
#define PHY_M_MAC_MD_MSK (7<<7) /* Bit 9.. 7: Mode Select Mask */
|
|
#define PHY_M_MAC_MD_AUTO 3 /* Auto Copper/1000Base-X */
|
|
#define PHY_M_MAC_MD_COPPER 5 /* Copper only */
|
|
#define PHY_M_MAC_MD_1000BX 7 /* 1000Base-X only */
|
|
#define PHY_M_MAC_MODE_SEL(x) (SHIFT7(x) & PHY_M_MAC_MD_MSK)
|
|
|
|
/***** PHY_MARV_PHY_CTRL (page 3) 16 bit r/w LED Control Reg. *****/
|
|
#define PHY_M_LEDC_LOS_MSK (0xf<<12) /* Bit 15..12: LOS LED Ctrl. Mask */
|
|
#define PHY_M_LEDC_INIT_MSK (0xf<<8) /* Bit 11.. 8: INIT LED Ctrl. Mask */
|
|
#define PHY_M_LEDC_STA1_MSK (0xf<<4) /* Bit 7.. 4: STAT1 LED Ctrl. Mask */
|
|
#define PHY_M_LEDC_STA0_MSK 0xf /* Bit 3.. 0: STAT0 LED Ctrl. Mask */
|
|
|
|
#define PHY_M_LEDC_LOS_CTRL(x) (SHIFT12(x) & PHY_M_LEDC_LOS_MSK)
|
|
#define PHY_M_LEDC_INIT_CTRL(x) (SHIFT8(x) & PHY_M_LEDC_INIT_MSK)
|
|
#define PHY_M_LEDC_STA1_CTRL(x) (SHIFT4(x) & PHY_M_LEDC_STA1_MSK)
|
|
#define PHY_M_LEDC_STA0_CTRL(x) (SHIFT0(x) & PHY_M_LEDC_STA0_MSK)
|
|
|
|
/***** PHY_MARV_PHY_STAT (page 3) 16 bit r/w Polarity Control Reg. *****/
|
|
#define PHY_M_POLC_LS1M_MSK (0xf<<12) /* Bit 15..12: LOS,STAT1 Mix % Mask */
|
|
#define PHY_M_POLC_IS0M_MSK (0xf<<8) /* Bit 11.. 8: INIT,STAT0 Mix % Mask */
|
|
#define PHY_M_POLC_LOS_MSK (0x3<<6) /* Bit 7.. 6: LOS Pol. Ctrl. Mask */
|
|
#define PHY_M_POLC_INIT_MSK (0x3<<4) /* Bit 5.. 4: INIT Pol. Ctrl. Mask */
|
|
#define PHY_M_POLC_STA1_MSK (0x3<<2) /* Bit 3.. 2: STAT1 Pol. Ctrl. Mask */
|
|
#define PHY_M_POLC_STA0_MSK 0x3 /* Bit 1.. 0: STAT0 Pol. Ctrl. Mask */
|
|
|
|
#define PHY_M_POLC_LS1_P_MIX(x) (SHIFT12(x) & PHY_M_POLC_LS1M_MSK)
|
|
#define PHY_M_POLC_IS0_P_MIX(x) (SHIFT8(x) & PHY_M_POLC_IS0M_MSK)
|
|
#define PHY_M_POLC_LOS_CTRL(x) (SHIFT6(x) & PHY_M_POLC_LOS_MSK)
|
|
#define PHY_M_POLC_INIT_CTRL(x) (SHIFT4(x) & PHY_M_POLC_INIT_MSK)
|
|
#define PHY_M_POLC_STA1_CTRL(x) (SHIFT2(x) & PHY_M_POLC_STA1_MSK)
|
|
#define PHY_M_POLC_STA0_CTRL(x) (SHIFT0(x) & PHY_M_POLC_STA0_MSK)
|
|
|
|
/*
|
|
* GMAC registers
|
|
*
|
|
* The GMAC registers are 16 or 32 bits wide.
|
|
* The GMACs host processor interface is 16 bits wide,
|
|
* therefore ALL registers will be addressed with 16 bit accesses.
|
|
*
|
|
* Note: NA reg = Network Address e.g DA, SA etc.
|
|
*/
|
|
|
|
/* Port Registers */
|
|
#define GM_GP_STAT 0x0000 /* 16 bit r/o General Purpose Status */
|
|
#define GM_GP_CTRL 0x0004 /* 16 bit r/w General Purpose Control */
|
|
#define GM_TX_CTRL 0x0008 /* 16 bit r/w Transmit Control Reg. */
|
|
#define GM_RX_CTRL 0x000c /* 16 bit r/w Receive Control Reg. */
|
|
#define GM_TX_FLOW_CTRL 0x0010 /* 16 bit r/w Transmit Flow-Control */
|
|
#define GM_TX_PARAM 0x0014 /* 16 bit r/w Transmit Parameter Reg. */
|
|
#define GM_SERIAL_MODE 0x0018 /* 16 bit r/w Serial Mode Register */
|
|
|
|
/* Source Address Registers */
|
|
#define GM_SRC_ADDR_1L 0x001c /* 16 bit r/w Source Address 1 (low) */
|
|
#define GM_SRC_ADDR_1M 0x0020 /* 16 bit r/w Source Address 1 (middle) */
|
|
#define GM_SRC_ADDR_1H 0x0024 /* 16 bit r/w Source Address 1 (high) */
|
|
#define GM_SRC_ADDR_2L 0x0028 /* 16 bit r/w Source Address 2 (low) */
|
|
#define GM_SRC_ADDR_2M 0x002c /* 16 bit r/w Source Address 2 (middle) */
|
|
#define GM_SRC_ADDR_2H 0x0030 /* 16 bit r/w Source Address 2 (high) */
|
|
|
|
/* Multicast Address Hash Registers */
|
|
#define GM_MC_ADDR_H1 0x0034 /* 16 bit r/w Multicast Address Hash 1 */
|
|
#define GM_MC_ADDR_H2 0x0038 /* 16 bit r/w Multicast Address Hash 2 */
|
|
#define GM_MC_ADDR_H3 0x003c /* 16 bit r/w Multicast Address Hash 3 */
|
|
#define GM_MC_ADDR_H4 0x0040 /* 16 bit r/w Multicast Address Hash 4 */
|
|
|
|
/* Interrupt Source Registers */
|
|
#define GM_TX_IRQ_SRC 0x0044 /* 16 bit r/o Tx Overflow IRQ Source */
|
|
#define GM_RX_IRQ_SRC 0x0048 /* 16 bit r/o Rx Overflow IRQ Source */
|
|
#define GM_TR_IRQ_SRC 0x004c /* 16 bit r/o Tx/Rx Over. IRQ Source */
|
|
|
|
/* Interrupt Mask Registers */
|
|
#define GM_TX_IRQ_MSK 0x0050 /* 16 bit r/w Tx Overflow IRQ Mask */
|
|
#define GM_RX_IRQ_MSK 0x0054 /* 16 bit r/w Rx Overflow IRQ Mask */
|
|
#define GM_TR_IRQ_MSK 0x0058 /* 16 bit r/w Tx/Rx Over. IRQ Mask */
|
|
|
|
/* Serial Management Interface (SMI) Registers */
|
|
#define GM_SMI_CTRL 0x0080 /* 16 bit r/w SMI Control Register */
|
|
#define GM_SMI_DATA 0x0084 /* 16 bit r/w SMI Data Register */
|
|
#define GM_PHY_ADDR 0x0088 /* 16 bit r/w GPHY Address Register */
|
|
|
|
/* MIB Counters */
|
|
#define GM_MIB_CNT_BASE 0x0100 /* Base Address of MIB Counters */
|
|
#define GM_MIB_CNT_SIZE 44 /* Number of MIB Counters */
|
|
|
|
/*
|
|
* MIB Counters base address definitions (low word) -
|
|
* use offset 4 for access to high word (32 bit r/o)
|
|
*/
|
|
#define GM_RXF_UC_OK \
|
|
(GM_MIB_CNT_BASE + 0) /* Unicast Frames Received OK */
|
|
#define GM_RXF_BC_OK \
|
|
(GM_MIB_CNT_BASE + 8) /* Broadcast Frames Received OK */
|
|
#define GM_RXF_MPAUSE \
|
|
(GM_MIB_CNT_BASE + 16) /* Pause MAC Ctrl Frames Received */
|
|
#define GM_RXF_MC_OK \
|
|
(GM_MIB_CNT_BASE + 24) /* Multicast Frames Received OK */
|
|
#define GM_RXF_FCS_ERR \
|
|
(GM_MIB_CNT_BASE + 32) /* Rx Frame Check Seq. Error */
|
|
#define GM_RXO_OK_LO \
|
|
(GM_MIB_CNT_BASE + 48) /* Octets Received OK Low */
|
|
#define GM_RXO_OK_HI \
|
|
(GM_MIB_CNT_BASE + 56) /* Octets Received OK High */
|
|
#define GM_RXO_ERR_LO \
|
|
(GM_MIB_CNT_BASE + 64) /* Octets Received Invalid Low */
|
|
#define GM_RXO_ERR_HI \
|
|
(GM_MIB_CNT_BASE + 72) /* Octets Received Invalid High */
|
|
#define GM_RXF_SHT \
|
|
(GM_MIB_CNT_BASE + 80) /* Frames <64 Byte Received OK */
|
|
#define GM_RXE_FRAG \
|
|
(GM_MIB_CNT_BASE + 88) /* Frames <64 Byte Received with FCS Err */
|
|
#define GM_RXF_64B \
|
|
(GM_MIB_CNT_BASE + 96) /* 64 Byte Rx Frame */
|
|
#define GM_RXF_127B \
|
|
(GM_MIB_CNT_BASE + 104) /* 65-127 Byte Rx Frame */
|
|
#define GM_RXF_255B \
|
|
(GM_MIB_CNT_BASE + 112) /* 128-255 Byte Rx Frame */
|
|
#define GM_RXF_511B \
|
|
(GM_MIB_CNT_BASE + 120) /* 256-511 Byte Rx Frame */
|
|
#define GM_RXF_1023B \
|
|
(GM_MIB_CNT_BASE + 128) /* 512-1023 Byte Rx Frame */
|
|
#define GM_RXF_1518B \
|
|
(GM_MIB_CNT_BASE + 136) /* 1024-1518 Byte Rx Frame */
|
|
#define GM_RXF_MAX_SZ \
|
|
(GM_MIB_CNT_BASE + 144) /* 1519-MaxSize Byte Rx Frame */
|
|
#define GM_RXF_LNG_ERR \
|
|
(GM_MIB_CNT_BASE + 152) /* Rx Frame too Long Error */
|
|
#define GM_RXF_JAB_PKT \
|
|
(GM_MIB_CNT_BASE + 160) /* Rx Jabber Packet Frame */
|
|
#define GM_RXE_FIFO_OV \
|
|
(GM_MIB_CNT_BASE + 176) /* Rx FIFO overflow Event */
|
|
#define GM_TXF_UC_OK \
|
|
(GM_MIB_CNT_BASE + 192) /* Unicast Frames Xmitted OK */
|
|
#define GM_TXF_BC_OK \
|
|
(GM_MIB_CNT_BASE + 200) /* Broadcast Frames Xmitted OK */
|
|
#define GM_TXF_MPAUSE \
|
|
(GM_MIB_CNT_BASE + 208) /* Pause MAC Ctrl Frames Xmitted */
|
|
#define GM_TXF_MC_OK \
|
|
(GM_MIB_CNT_BASE + 216) /* Multicast Frames Xmitted OK */
|
|
#define GM_TXO_OK_LO \
|
|
(GM_MIB_CNT_BASE + 224) /* Octets Transmitted OK Low */
|
|
#define GM_TXO_OK_HI \
|
|
(GM_MIB_CNT_BASE + 232) /* Octets Transmitted OK High */
|
|
#define GM_TXF_64B \
|
|
(GM_MIB_CNT_BASE + 240) /* 64 Byte Tx Frame */
|
|
#define GM_TXF_127B \
|
|
(GM_MIB_CNT_BASE + 248) /* 65-127 Byte Tx Frame */
|
|
#define GM_TXF_255B \
|
|
(GM_MIB_CNT_BASE + 256) /* 128-255 Byte Tx Frame */
|
|
#define GM_TXF_511B \
|
|
(GM_MIB_CNT_BASE + 264) /* 256-511 Byte Tx Frame */
|
|
#define GM_TXF_1023B \
|
|
(GM_MIB_CNT_BASE + 272) /* 512-1023 Byte Tx Frame */
|
|
#define GM_TXF_1518B \
|
|
(GM_MIB_CNT_BASE + 280) /* 1024-1518 Byte Tx Frame */
|
|
#define GM_TXF_MAX_SZ \
|
|
(GM_MIB_CNT_BASE + 288) /* 1519-MaxSize Byte Tx Frame */
|
|
#define GM_TXF_COL \
|
|
(GM_MIB_CNT_BASE + 304) /* Tx Collision */
|
|
#define GM_TXF_LAT_COL \
|
|
(GM_MIB_CNT_BASE + 312) /* Tx Late Collision */
|
|
#define GM_TXF_ABO_COL \
|
|
(GM_MIB_CNT_BASE + 320) /* Tx aborted due to Exces. Col. */
|
|
#define GM_TXF_MUL_COL \
|
|
(GM_MIB_CNT_BASE + 328) /* Tx Multiple Collision */
|
|
#define GM_TXF_SNG_COL \
|
|
(GM_MIB_CNT_BASE + 336) /* Tx Single Collision */
|
|
#define GM_TXE_FIFO_UR \
|
|
(GM_MIB_CNT_BASE + 344) /* Tx FIFO Underrun Event */
|
|
|
|
/*----------------------------------------------------------------------------*/
|
|
/*
|
|
* GMAC Bit Definitions
|
|
*
|
|
* If the bit access behaviour differs from the register access behaviour
|
|
* (r/w, r/o) this is documented after the bit number.
|
|
* The following bit access behaviours are used:
|
|
* (sc) self clearing
|
|
* (r/o) read only
|
|
*/
|
|
|
|
/* GM_GP_STAT 16 bit r/o General Purpose Status Register */
|
|
#define GM_GPSR_SPEED BIT_15 /* Port Speed (1 = 100 Mbps) */
|
|
#define GM_GPSR_DUPLEX BIT_14 /* Duplex Mode (1 = Full) */
|
|
#define GM_GPSR_FC_TX_DIS BIT_13 /* Tx Flow-Control Mode Disabled */
|
|
#define GM_GPSR_LINK_UP BIT_12 /* Link Up Status */
|
|
#define GM_GPSR_PAUSE BIT_11 /* Pause State */
|
|
#define GM_GPSR_TX_ACTIVE BIT_10 /* Tx in Progress */
|
|
#define GM_GPSR_EXC_COL BIT_9 /* Excessive Collisions Occured */
|
|
#define GM_GPSR_LAT_COL BIT_8 /* Late Collisions Occured */
|
|
#define GM_GPSR_PHY_ST_CH BIT_5 /* PHY Status Change */
|
|
#define GM_GPSR_GIG_SPEED BIT_4 /* Gigabit Speed (1 = 1000 Mbps) */
|
|
#define GM_GPSR_PART_MODE BIT_3 /* Partition mode */
|
|
#define GM_GPSR_FC_RX_DIS BIT_2 /* Rx Flow-Control Mode Disabled */
|
|
|
|
/* GM_GP_CTRL 16 bit r/w General Purpose Control Register */
|
|
#define GM_GPCR_RMII_PH_ENA BIT_15 /* Enable RMII for PHY (Yukon-FE only) */
|
|
#define GM_GPCR_RMII_LB_ENA BIT_14 /* Enable RMII Loopback (Yukon-FE only) */
|
|
#define GM_GPCR_FC_TX_DIS BIT_13 /* Disable Tx Flow-Control Mode */
|
|
#define GM_GPCR_TX_ENA BIT_12 /* Enable Transmit */
|
|
#define GM_GPCR_RX_ENA BIT_11 /* Enable Receive */
|
|
#define GM_GPCR_LOOP_ENA BIT_9 /* Enable MAC Loopback Mode */
|
|
#define GM_GPCR_PART_ENA BIT_8 /* Enable Partition Mode */
|
|
#define GM_GPCR_GIGS_ENA BIT_7 /* Gigabit Speed (1000 Mbps) */
|
|
#define GM_GPCR_FL_PASS BIT_6 /* Force Link Pass */
|
|
#define GM_GPCR_DUP_FULL BIT_5 /* Full Duplex Mode */
|
|
#define GM_GPCR_FC_RX_DIS BIT_4 /* Disable Rx Flow-Control Mode */
|
|
#define GM_GPCR_SPEED_100 BIT_3 /* Port Speed 100 Mbps */
|
|
#define GM_GPCR_AU_DUP_DIS BIT_2 /* Disable Auto-Update Duplex */
|
|
#define GM_GPCR_AU_FCT_DIS BIT_1 /* Disable Auto-Update Flow-C. */
|
|
#define GM_GPCR_AU_SPD_DIS BIT_0 /* Disable Auto-Update Speed */
|
|
|
|
#define GM_GPCR_SPEED_1000 (GM_GPCR_GIGS_ENA | GM_GPCR_SPEED_100)
|
|
#define GM_GPCR_AU_ALL_DIS (GM_GPCR_AU_DUP_DIS | GM_GPCR_AU_FCT_DIS |\
|
|
GM_GPCR_AU_SPD_DIS)
|
|
|
|
/* GM_TX_CTRL 16 bit r/w Transmit Control Register */
|
|
#define GM_TXCR_FORCE_JAM BIT_15 /* Force Jam / Flow-Control */
|
|
#define GM_TXCR_CRC_DIS BIT_14 /* Disable insertion of CRC */
|
|
#define GM_TXCR_PAD_DIS BIT_13 /* Disable padding of packets */
|
|
#define GM_TXCR_COL_THR_MSK (7<<10) /* Bit 12..10: Collision Threshold Mask */
|
|
#define GM_TXCR_PAD_PAT_MSK 0xff /* Bit 7.. 0: Padding Pattern Mask */
|
|
/* (Yukon-2 only) */
|
|
|
|
#define TX_COL_THR(x) (SHIFT10(x) & GM_TXCR_COL_THR_MSK)
|
|
#define TX_COL_DEF 0x04
|
|
|
|
/* GM_RX_CTRL 16 bit r/w Receive Control Register */
|
|
#define GM_RXCR_UCF_ENA BIT_15 /* Enable Unicast filtering */
|
|
#define GM_RXCR_MCF_ENA BIT_14 /* Enable Multicast filtering */
|
|
#define GM_RXCR_CRC_DIS BIT_13 /* Remove 4-byte CRC */
|
|
#define GM_RXCR_PASS_FC BIT_12 /* Pass FC packets to FIFO (Yukon-1 only) */
|
|
|
|
/* GM_TX_PARAM 16 bit r/w Transmit Parameter Register */
|
|
#define GM_TXPA_JAMLEN_MSK (3<<14) /* Bit 15..14: Jam Length Mask */
|
|
#define GM_TXPA_JAMIPG_MSK (0x1f<<9) /* Bit 13.. 9: Jam IPG Mask */
|
|
#define GM_TXPA_JAMDAT_MSK (0x1f<<4) /* Bit 8.. 4: IPG Jam to Data Mask */
|
|
#define GM_TXPA_BO_LIM_MSK 0x0f /* Bit 3.. 0: Backoff Limit Mask */
|
|
/* (Yukon-2 only) */
|
|
|
|
#define TX_JAM_LEN_VAL(x) (SHIFT14(x) & GM_TXPA_JAMLEN_MSK)
|
|
#define TX_JAM_IPG_VAL(x) (SHIFT9(x) & GM_TXPA_JAMIPG_MSK)
|
|
#define TX_IPG_JAM_DATA(x) (SHIFT4(x) & GM_TXPA_JAMDAT_MSK)
|
|
#define TX_BACK_OFF_LIM(x) ((x) & GM_TXPA_BO_LIM_MSK)
|
|
|
|
#define TX_JAM_LEN_DEF 0x03
|
|
#define TX_JAM_IPG_DEF 0x0b
|
|
#define TX_IPG_JAM_DEF 0x1c
|
|
#define TX_BOF_LIM_DEF 0x04
|
|
|
|
/* GM_SERIAL_MODE 16 bit r/w Serial Mode Register */
|
|
#define GM_SMOD_DATABL_MSK (0x1f<<11) /* Bit 15..11: Data Blinder */
|
|
/* r/o on Yukon, r/w on Yukon-EC */
|
|
#define GM_SMOD_LIMIT_4 BIT_10 /* 4 consecutive Tx trials */
|
|
#define GM_SMOD_VLAN_ENA BIT_9 /* Enable VLAN (Max. Frame Len) */
|
|
#define GM_SMOD_JUMBO_ENA BIT_8 /* Enable Jumbo (Max. Frame Len) */
|
|
#define GM_SMOD_IPG_MSK 0x1f /* Bit 4.. 0: Inter-Packet Gap (IPG) */
|
|
|
|
#define DATA_BLIND_VAL(x) (SHIFT11(x) & GM_SMOD_DATABL_MSK)
|
|
#define IPG_DATA_VAL(x) ((x) & GM_SMOD_IPG_MSK)
|
|
|
|
#define DATA_BLIND_DEF 0x04
|
|
#define IPG_DATA_DEF 0x1e
|
|
|
|
/* GM_SMI_CTRL 16 bit r/w SMI Control Register */
|
|
#define GM_SMI_CT_PHY_A_MSK (0x1f<<11) /* Bit 15..11: PHY Device Address */
|
|
#define GM_SMI_CT_REG_A_MSK (0x1f<<6) /* Bit 10.. 6: PHY Register Address */
|
|
#define GM_SMI_CT_OP_RD BIT_5 /* OpCode Read (0=Write)*/
|
|
#define GM_SMI_CT_RD_VAL BIT_4 /* Read Valid (Read completed) */
|
|
#define GM_SMI_CT_BUSY BIT_3 /* Busy (Operation in progress) */
|
|
|
|
#define GM_SMI_CT_PHY_AD(x) (SHIFT11(x) & GM_SMI_CT_PHY_A_MSK)
|
|
#define GM_SMI_CT_REG_AD(x) (SHIFT6(x) & GM_SMI_CT_REG_A_MSK)
|
|
|
|
/* GM_PHY_ADDR 16 bit r/w GPHY Address Register */
|
|
#define GM_PAR_MIB_CLR BIT_5 /* Set MIB Clear Counter Mode */
|
|
#define GM_PAR_MIB_TST BIT_4 /* MIB Load Counter (Test Mode) */
|
|
|
|
/* Receive Frame Status Encoding */
|
|
#define GMR_FS_LEN_MSK (0xffff<<16) /* Bit 31..16: Rx Frame Length */
|
|
#define GMR_FS_VLAN BIT_13 /* VLAN Packet */
|
|
#define GMR_FS_JABBER BIT_12 /* Jabber Packet */
|
|
#define GMR_FS_UN_SIZE BIT_11 /* Undersize Packet */
|
|
#define GMR_FS_MC BIT_10 /* Multicast Packet */
|
|
#define GMR_FS_BC BIT_9 /* Broadcast Packet */
|
|
#define GMR_FS_RX_OK BIT_8 /* Receive OK (Good Packet) */
|
|
#define GMR_FS_GOOD_FC BIT_7 /* Good Flow-Control Packet */
|
|
#define GMR_FS_BAD_FC BIT_6 /* Bad Flow-Control Packet */
|
|
#define GMR_FS_MII_ERR BIT_5 /* MII Error */
|
|
#define GMR_FS_LONG_ERR BIT_4 /* Too Long Packet */
|
|
#define GMR_FS_FRAGMENT BIT_3 /* Fragment */
|
|
#define GMR_FS_CRC_ERR BIT_1 /* CRC Error */
|
|
#define GMR_FS_RX_FF_OV BIT_0 /* Rx FIFO Overflow */
|
|
|
|
#define GMR_FS_LEN_SHIFT 16
|
|
|
|
#define GMR_FS_ANY_ERR ( \
|
|
GMR_FS_RX_FF_OV | \
|
|
GMR_FS_CRC_ERR | \
|
|
GMR_FS_FRAGMENT | \
|
|
GMR_FS_LONG_ERR | \
|
|
GMR_FS_MII_ERR | \
|
|
GMR_FS_BAD_FC | \
|
|
GMR_FS_UN_SIZE | \
|
|
GMR_FS_JABBER)
|
|
|
|
/* Rx GMAC FIFO Flush Mask (default) */
|
|
#define RX_FF_FL_DEF_MSK GMR_FS_ANY_ERR
|
|
|
|
/* Receive and Transmit GMAC FIFO Registers (YUKON only) */
|
|
|
|
/* RX_GMF_EA 32 bit Rx GMAC FIFO End Address */
|
|
/* RX_GMF_AF_THR 32 bit Rx GMAC FIFO Almost Full Thresh. */
|
|
/* RX_GMF_WP 32 bit Rx GMAC FIFO Write Pointer */
|
|
/* RX_GMF_WLEV 32 bit Rx GMAC FIFO Write Level */
|
|
/* RX_GMF_RP 32 bit Rx GMAC FIFO Read Pointer */
|
|
/* RX_GMF_RLEV 32 bit Rx GMAC FIFO Read Level */
|
|
/* TX_GMF_EA 32 bit Tx GMAC FIFO End Address */
|
|
/* TX_GMF_AE_THR 32 bit Tx GMAC FIFO Almost Empty Thresh.*/
|
|
/* TX_GMF_WP 32 bit Tx GMAC FIFO Write Pointer */
|
|
/* TX_GMF_WSP 32 bit Tx GMAC FIFO Write Shadow Pointer */
|
|
/* TX_GMF_WLEV 32 bit Tx GMAC FIFO Write Level */
|
|
/* TX_GMF_RP 32 bit Tx GMAC FIFO Read Pointer */
|
|
/* TX_GMF_RSTP 32 bit Tx GMAC FIFO Restart Pointer */
|
|
/* TX_GMF_RLEV 32 bit Tx GMAC FIFO Read Level */
|
|
|
|
/* RX_GMF_CTRL_T 32 bit Rx GMAC FIFO Control/Test */
|
|
#define RX_TRUNC_ON BIT_27 /* enable packet truncation */
|
|
#define RX_TRUNC_OFF BIT_26 /* disable packet truncation */
|
|
#define RX_VLAN_STRIP_ON BIT_25 /* enable VLAN stripping */
|
|
#define RX_VLAN_STRIP_OFF BIT_24 /* disable VLAN stripping */
|
|
#define GMF_WP_TST_ON BIT_14 /* Write Pointer Test On */
|
|
#define GMF_WP_TST_OFF BIT_13 /* Write Pointer Test Off */
|
|
#define GMF_WP_STEP BIT_12 /* Write Pointer Step/Increment */
|
|
#define GMF_RP_TST_ON BIT_10 /* Read Pointer Test On */
|
|
#define GMF_RP_TST_OFF BIT_9 /* Read Pointer Test Off */
|
|
#define GMF_RP_STEP BIT_8 /* Read Pointer Step/Increment */
|
|
#define GMF_RX_F_FL_ON BIT_7 /* Rx FIFO Flush Mode On */
|
|
#define GMF_RX_F_FL_OFF BIT_6 /* Rx FIFO Flush Mode Off */
|
|
#define GMF_CLI_RX_FO BIT_5 /* Clear IRQ Rx FIFO Overrun */
|
|
#define GMF_CLI_RX_FC BIT_4 /* Clear IRQ Rx Frame Complete */
|
|
#define GMF_OPER_ON BIT_3 /* Operational Mode On */
|
|
#define GMF_OPER_OFF BIT_2 /* Operational Mode Off */
|
|
#define GMF_RST_CLR BIT_1 /* Clear GMAC FIFO Reset */
|
|
#define GMF_RST_SET BIT_0 /* Set GMAC FIFO Reset */
|
|
|
|
/* TX_GMF_CTRL_T 32 bit Tx GMAC FIFO Control/Test (YUKON and Yukon-2) */
|
|
#define TX_STFW_DIS BIT_31 /* Disable Store & Forward (Yukon-EC Ultra) */
|
|
#define TX_STFW_ENA BIT_30 /* Enable Store & Forward (Yukon-EC Ultra) */
|
|
#define TX_VLAN_TAG_ON BIT_25 /* enable VLAN tagging */
|
|
#define TX_VLAN_TAG_OFF BIT_24 /* disable VLAN tagging */
|
|
#define TX_JUMBO_ENA BIT_23 /* Enable Jumbo Mode (Yukon-EC Ultra) */
|
|
#define TX_JUMBO_DIS BIT_22 /* Disable Jumbo Mode (Yukon-EC Ultra) */
|
|
#define GMF_WSP_TST_ON BIT_18 /* Write Shadow Pointer Test On */
|
|
#define GMF_WSP_TST_OFF BIT_17 /* Write Shadow Pointer Test Off */
|
|
#define GMF_WSP_STEP BIT_16 /* Write Shadow Pointer Step/Increment */
|
|
/* Bits 15..8: same as for RX_GMF_CTRL_T */
|
|
#define GMF_CLI_TX_FU BIT_6 /* Clear IRQ Tx FIFO Underrun */
|
|
#define GMF_CLI_TX_FC BIT_5 /* Clear IRQ Tx Frame Complete */
|
|
#define GMF_CLI_TX_PE BIT_4 /* Clear IRQ Tx Parity Error */
|
|
/* Bits 3..0: same as for RX_GMF_CTRL_T */
|
|
|
|
#define GMF_RX_CTRL_DEF (GMF_OPER_ON | GMF_RX_F_FL_ON)
|
|
#define GMF_TX_CTRL_DEF GMF_OPER_ON
|
|
|
|
#define RX_GMF_AF_THR_MIN 0x0c /* Rx GMAC FIFO Almost Full Thresh. min. */
|
|
#define RX_GMF_FL_THR_DEF 0x0a /* Rx GMAC FIFO Flush Threshold default */
|
|
|
|
/* GMAC_TI_ST_CTRL 8 bit Time Stamp Timer Ctrl Reg (YUKON only) */
|
|
#define GMT_ST_START BIT_2 /* Start Time Stamp Timer */
|
|
#define GMT_ST_STOP BIT_1 /* Stop Time Stamp Timer */
|
|
#define GMT_ST_CLR_IRQ BIT_0 /* Clear Time Stamp Timer IRQ */
|
|
|
|
/* POLL_CTRL 32 bit Polling Unit control register (Yukon-2 only) */
|
|
#define PC_CLR_IRQ_CHK BIT_5 /* Clear IRQ Check */
|
|
#define PC_POLL_RQ BIT_4 /* Poll Request Start */
|
|
#define PC_POLL_OP_ON BIT_3 /* Operational Mode On */
|
|
#define PC_POLL_OP_OFF BIT_2 /* Operational Mode Off */
|
|
#define PC_POLL_RST_CLR BIT_1 /* Clear Polling Unit Reset (Enable) */
|
|
#define PC_POLL_RST_SET BIT_0 /* Set Polling Unit Reset */
|
|
|
|
/* B28_Y2_ASF_STAT_CMD 32 bit ASF Status and Command Reg */
|
|
/* This register is used by the host driver software */
|
|
#define Y2_ASF_OS_PRES BIT_4 /* ASF operation system present */
|
|
#define Y2_ASF_RESET BIT_3 /* ASF system in reset state */
|
|
#define Y2_ASF_RUNNING BIT_2 /* ASF system operational */
|
|
#define Y2_ASF_CLR_HSTI BIT_1 /* Clear ASF IRQ */
|
|
#define Y2_ASF_IRQ BIT_0 /* Issue an IRQ to ASF system */
|
|
|
|
#define Y2_ASF_UC_STATE (3<<2) /* ASF uC State */
|
|
#define Y2_ASF_CLK_HALT 0 /* ASF system clock stopped */
|
|
|
|
/* B28_Y2_ASF_HOST_COM 32 bit ASF Host Communication Reg */
|
|
/* This register is used by the ASF firmware */
|
|
#define Y2_ASF_CLR_ASFI BIT_1 /* Clear host IRQ */
|
|
#define Y2_ASF_HOST_IRQ BIT_0 /* Issue an IRQ to HOST system */
|
|
|
|
/* STAT_CTRL 32 bit Status BMU control register (Yukon-2 only) */
|
|
#define SC_STAT_CLR_IRQ BIT_4 /* Status Burst IRQ clear */
|
|
#define SC_STAT_OP_ON BIT_3 /* Operational Mode On */
|
|
#define SC_STAT_OP_OFF BIT_2 /* Operational Mode Off */
|
|
#define SC_STAT_RST_CLR BIT_1 /* Clear Status Unit Reset (Enable) */
|
|
#define SC_STAT_RST_SET BIT_0 /* Set Status Unit Reset */
|
|
|
|
/* GMAC_CTRL 32 bit GMAC Control Reg (YUKON only) */
|
|
#define GMC_H_BURST_ON BIT_7 /* Half Duplex Burst Mode On */
|
|
#define GMC_H_BURST_OFF BIT_6 /* Half Duplex Burst Mode Off */
|
|
#define GMC_F_LOOPB_ON BIT_5 /* FIFO Loopback On */
|
|
#define GMC_F_LOOPB_OFF BIT_4 /* FIFO Loopback Off */
|
|
#define GMC_PAUSE_ON BIT_3 /* Pause On */
|
|
#define GMC_PAUSE_OFF BIT_2 /* Pause Off */
|
|
#define GMC_RST_CLR BIT_1 /* Clear GMAC Reset */
|
|
#define GMC_RST_SET BIT_0 /* Set GMAC Reset */
|
|
|
|
/* GPHY_CTRL 32 bit GPHY Control Reg (YUKON only) */
|
|
#define GPC_SEL_BDT BIT_28 /* Select Bi-Dir. Transfer for MDC/MDIO */
|
|
#define GPC_INT_POL BIT_27 /* IRQ Polarity is Active Low */
|
|
#define GPC_75_OHM BIT_26 /* Use 75 Ohm Termination instead of 50 */
|
|
#define GPC_DIS_FC BIT_25 /* Disable Automatic Fiber/Copper Detection */
|
|
#define GPC_DIS_SLEEP BIT_24 /* Disable Energy Detect */
|
|
#define GPC_HWCFG_M_3 BIT_23 /* HWCFG_MODE[3] */
|
|
#define GPC_HWCFG_M_2 BIT_22 /* HWCFG_MODE[2] */
|
|
#define GPC_HWCFG_M_1 BIT_21 /* HWCFG_MODE[1] */
|
|
#define GPC_HWCFG_M_0 BIT_20 /* HWCFG_MODE[0] */
|
|
#define GPC_ANEG_0 BIT_19 /* ANEG[0] */
|
|
#define GPC_ENA_XC BIT_18 /* Enable MDI crossover */
|
|
#define GPC_DIS_125 BIT_17 /* Disable 125 MHz clock */
|
|
#define GPC_ANEG_3 BIT_16 /* ANEG[3] */
|
|
#define GPC_ANEG_2 BIT_15 /* ANEG[2] */
|
|
#define GPC_ANEG_1 BIT_14 /* ANEG[1] */
|
|
#define GPC_ENA_PAUSE BIT_13 /* Enable Pause (SYM_OR_REM) */
|
|
#define GPC_PHYADDR_4 BIT_12 /* Bit 4 of Phy Addr */
|
|
#define GPC_PHYADDR_3 BIT_11 /* Bit 3 of Phy Addr */
|
|
#define GPC_PHYADDR_2 BIT_10 /* Bit 2 of Phy Addr */
|
|
#define GPC_PHYADDR_1 BIT_9 /* Bit 1 of Phy Addr */
|
|
#define GPC_PHYADDR_0 BIT_8 /* Bit 0 of Phy Addr */
|
|
#define GPC_RST_CLR BIT_1 /* Clear GPHY Reset */
|
|
#define GPC_RST_SET BIT_0 /* Set GPHY Reset */
|
|
|
|
/* GMAC_IRQ_SRC 8 bit GMAC Interrupt Source Reg (YUKON only) */
|
|
/* GMAC_IRQ_MSK 8 bit GMAC Interrupt Mask Reg (YUKON only) */
|
|
#define GM_IS_RX_CO_OV BIT_5 /* Receive Counter Overflow IRQ */
|
|
#define GM_IS_TX_CO_OV BIT_4 /* Transmit Counter Overflow IRQ */
|
|
#define GM_IS_TX_FF_UR BIT_3 /* Transmit FIFO Underrun */
|
|
#define GM_IS_TX_COMPL BIT_2 /* Frame Transmission Complete */
|
|
#define GM_IS_RX_FF_OR BIT_1 /* Receive FIFO Overrun */
|
|
#define GM_IS_RX_COMPL BIT_0 /* Frame Reception Complete */
|
|
|
|
#define GMAC_DEF_MSK (GM_IS_RX_CO_OV | GM_IS_TX_CO_OV | GM_IS_TX_FF_UR)
|
|
|
|
/* GMAC_LINK_CTRL 16 bit GMAC Link Control Reg (YUKON only) */
|
|
#define GMLC_RST_CLR BIT_1 /* Clear GMAC Link Reset */
|
|
#define GMLC_RST_SET BIT_0 /* Set GMAC Link Reset */
|
|
|
|
#define MSK_PORT_A 0
|
|
#define MSK_PORT_B 1
|
|
|
|
/* Register access macros */
|
|
#define CSR_WRITE_4(sc, reg, val) \
|
|
bus_write_4((sc)->msk_res[0], (reg), (val))
|
|
#define CSR_WRITE_2(sc, reg, val) \
|
|
bus_write_2((sc)->msk_res[0], (reg), (val))
|
|
#define CSR_WRITE_1(sc, reg, val) \
|
|
bus_write_1((sc)->msk_res[0], (reg), (val))
|
|
|
|
#define CSR_READ_4(sc, reg) \
|
|
bus_read_4((sc)->msk_res[0], (reg))
|
|
#define CSR_READ_2(sc, reg) \
|
|
bus_read_2((sc)->msk_res[0], (reg))
|
|
#define CSR_READ_1(sc, reg) \
|
|
bus_read_1((sc)->msk_res[0], (reg))
|
|
|
|
#define CSR_PCI_WRITE_4(sc, reg, val) \
|
|
bus_write_4((sc)->msk_res[0], Y2_CFG_SPC + (reg), (val))
|
|
#define CSR_PCI_WRITE_2(sc, reg, val) \
|
|
bus_write_2((sc)->msk_res[0], Y2_CFG_SPC + (reg), (val))
|
|
#define CSR_PCI_WRITE_1(sc, reg, val) \
|
|
bus_write_1((sc)->msk_res[0], Y2_CFG_SPC + (reg), (val))
|
|
|
|
#define CSR_PCI_READ_4(sc, reg) \
|
|
bus_read_4((sc)->msk_res[0], Y2_CFG_SPC + (reg))
|
|
#define CSR_PCI_READ_2(sc, reg) \
|
|
bus_read_2((sc)->msk_res[0], Y2_CFG_SPC + (reg))
|
|
#define CSR_PCI_READ_1(sc, reg) \
|
|
bus_read_1((sc)->msk_res[0], Y2_CFG_SPC + (reg))
|
|
|
|
#define MSK_IF_READ_4(sc_if, reg) \
|
|
CSR_READ_4((sc_if)->msk_softc, (reg))
|
|
#define MSK_IF_READ_2(sc_if, reg) \
|
|
CSR_READ_2((sc_if)->msk_softc, (reg))
|
|
#define MSK_IF_READ_1(sc_if, reg) \
|
|
CSR_READ_1((sc_if)->msk_softc, (reg))
|
|
|
|
#define MSK_IF_WRITE_4(sc_if, reg, val) \
|
|
CSR_WRITE_4((sc_if)->msk_softc, (reg), (val))
|
|
#define MSK_IF_WRITE_2(sc_if, reg, val) \
|
|
CSR_WRITE_2((sc_if)->msk_softc, (reg), (val))
|
|
#define MSK_IF_WRITE_1(sc_if, reg, val) \
|
|
CSR_WRITE_1((sc_if)->msk_softc, (reg), (val))
|
|
|
|
#define GMAC_REG(port, reg) \
|
|
((BASE_GMAC_1 + (port) * (BASE_GMAC_2 - BASE_GMAC_1)) | (reg))
|
|
#define GMAC_WRITE_2(sc, port, reg, val) \
|
|
CSR_WRITE_2((sc), GMAC_REG((port), (reg)), (val))
|
|
#define GMAC_READ_2(sc, port, reg) \
|
|
CSR_READ_2((sc), GMAC_REG((port), (reg)))
|
|
|
|
/* GPHY address (bits 15..11 of SMI control reg) */
|
|
#define PHY_ADDR_MARV 0
|
|
|
|
#define MSK_ADDR_LO(x) ((uint64_t) (x) & 0xffffffffUL)
|
|
#define MSK_ADDR_HI(x) ((uint64_t) (x) >> 32)
|
|
|
|
/*
|
|
* At first I guessed 8 bytes, the size of a single descriptor, would be
|
|
* required alignment constraints. But, it seems that Yukon II have 4096
|
|
* bytes boundary alignment constraints.
|
|
*/
|
|
#define MSK_RING_ALIGN 4096
|
|
#define MSK_STAT_ALIGN 4096
|
|
|
|
/* Rx descriptor data structure */
|
|
struct msk_rx_desc {
|
|
uint32_t msk_addr;
|
|
uint32_t msk_control;
|
|
};
|
|
|
|
/* Tx descriptor data structure */
|
|
struct msk_tx_desc {
|
|
uint32_t msk_addr;
|
|
uint32_t msk_control;
|
|
};
|
|
|
|
/* Status descriptor data structure */
|
|
struct msk_stat_desc {
|
|
uint32_t msk_status;
|
|
uint32_t msk_control;
|
|
};
|
|
|
|
/* mask and shift value to get Tx async queue status for port 1 */
|
|
#define STLE_TXA1_MSKL 0x00000fff
|
|
#define STLE_TXA1_SHIFTL 0
|
|
|
|
/* mask and shift value to get Tx sync queue status for port 1 */
|
|
#define STLE_TXS1_MSKL 0x00fff000
|
|
#define STLE_TXS1_SHIFTL 12
|
|
|
|
/* mask and shift value to get Tx async queue status for port 2 */
|
|
#define STLE_TXA2_MSKL 0xff000000
|
|
#define STLE_TXA2_SHIFTL 24
|
|
#define STLE_TXA2_MSKH 0x000f
|
|
/* this one shifts up */
|
|
#define STLE_TXA2_SHIFTH 8
|
|
|
|
/* mask and shift value to get Tx sync queue status for port 2 */
|
|
#define STLE_TXS2_MSKL 0x00000000
|
|
#define STLE_TXS2_SHIFTL 0
|
|
#define STLE_TXS2_MSKH 0xfff0
|
|
#define STLE_TXS2_SHIFTH 4
|
|
|
|
/* YUKON-2 bit values */
|
|
#define HW_OWNER 0x80000000
|
|
#define SW_OWNER 0x00000000
|
|
|
|
#define PU_PUTIDX_VALID 0x10000000
|
|
|
|
/* YUKON-2 Control flags */
|
|
#define UDPTCP 0x00010000
|
|
#define CALSUM 0x00020000
|
|
#define WR_SUM 0x00040000
|
|
#define INIT_SUM 0x00080000
|
|
#define LOCK_SUM 0x00100000
|
|
#define INS_VLAN 0x00200000
|
|
#define FRC_STAT 0x00400000
|
|
#define EOP 0x00800000
|
|
|
|
#define TX_LOCK 0x01000000
|
|
#define BUF_SEND 0x02000000
|
|
#define PACKET_SEND 0x04000000
|
|
|
|
#define NO_WARNING 0x40000000
|
|
#define NO_UPDATE 0x80000000
|
|
|
|
/* YUKON-2 Rx/Tx opcodes defines */
|
|
#define OP_TCPWRITE 0x11000000
|
|
#define OP_TCPSTART 0x12000000
|
|
#define OP_TCPINIT 0x14000000
|
|
#define OP_TCPLCK 0x18000000
|
|
#define OP_TCPCHKSUM OP_TCPSTART
|
|
#define OP_TCPIS (OP_TCPINIT | OP_TCPSTART)
|
|
#define OP_TCPLW (OP_TCPLCK | OP_TCPWRITE)
|
|
#define OP_TCPLSW (OP_TCPLCK | OP_TCPSTART | OP_TCPWRITE)
|
|
#define OP_TCPLISW (OP_TCPLCK | OP_TCPINIT | OP_TCPSTART | OP_TCPWRITE)
|
|
#define OP_ADDR64 0x21000000
|
|
#define OP_VLAN 0x22000000
|
|
#define OP_ADDR64VLAN (OP_ADDR64 | OP_VLAN)
|
|
#define OP_LRGLEN 0x24000000
|
|
#define OP_LRGLENVLAN (OP_LRGLEN | OP_VLAN)
|
|
#define OP_BUFFER 0x40000000
|
|
#define OP_PACKET 0x41000000
|
|
#define OP_LARGESEND 0x43000000
|
|
|
|
/* YUKON-2 STATUS opcodes defines */
|
|
#define OP_RXSTAT 0x60000000
|
|
#define OP_RXTIMESTAMP 0x61000000
|
|
#define OP_RXVLAN 0x62000000
|
|
#define OP_RXCHKS 0x64000000
|
|
#define OP_RXCHKSVLAN (OP_RXCHKS | OP_RXVLAN)
|
|
#define OP_RXTIMEVLAN (OP_RXTIMESTAMP | OP_RXVLAN)
|
|
#define OP_RSS_HASH 0x65000000
|
|
#define OP_TXINDEXLE 0x68000000
|
|
|
|
/* YUKON-2 SPECIAL opcodes defines */
|
|
#define OP_PUTIDX 0x70000000
|
|
|
|
#define STLE_OP_MASK 0xff000000
|
|
#define STLE_LEN_MASK 0x0000ffff
|
|
|
|
/* Descriptor Bit Definition */
|
|
/* TxCtrl Transmit Buffer Control Field */
|
|
/* RxCtrl Receive Buffer Control Field */
|
|
#define BMU_OWN BIT_31 /* OWN bit: 0=host/1=BMU */
|
|
#define BMU_STF BIT_30 /* Start of Frame */
|
|
#define BMU_EOF BIT_29 /* End of Frame */
|
|
#define BMU_IRQ_EOB BIT_28 /* Req "End of Buffer" IRQ */
|
|
#define BMU_IRQ_EOF BIT_27 /* Req "End of Frame" IRQ */
|
|
/* TxCtrl specific bits */
|
|
#define BMU_STFWD BIT_26 /* (Tx) Store & Forward Frame */
|
|
#define BMU_NO_FCS BIT_25 /* (Tx) Disable MAC FCS (CRC) generation */
|
|
#define BMU_SW BIT_24 /* (Tx) 1 bit res. for SW use */
|
|
/* RxCtrl specific bits */
|
|
#define BMU_DEV_0 BIT_26 /* (Rx) Transfer data to Dev0 */
|
|
#define BMU_STAT_VAL BIT_25 /* (Rx) Rx Status Valid */
|
|
#define BMU_TIST_VAL BIT_24 /* (Rx) Rx TimeStamp Valid */
|
|
/* Bit 23..16: BMU Check Opcodes */
|
|
#define BMU_CHECK (0x55<<16) /* Default BMU check */
|
|
#define BMU_TCP_CHECK (0x56<<16) /* Descr with TCP ext */
|
|
#define BMU_UDP_CHECK (0x57<<16) /* Descr with UDP ext (YUKON only) */
|
|
#define BMU_BBC 0xffff /* Bit 15.. 0: Buffer Byte Counter */
|
|
|
|
#define MSK_TX_RING_CNT 256
|
|
#define MSK_RX_RING_CNT 256
|
|
#define MSK_JUMBO_RX_RING_CNT MSK_RX_RING_CNT
|
|
#define MSK_STAT_RING_CNT ((1 + 3) * (MSK_TX_RING_CNT + MSK_RX_RING_CNT))
|
|
#define MSK_MAXTXSEGS 32
|
|
#define MSK_TSO_MAXSGSIZE 4096
|
|
#define MSK_TSO_MAXSIZE (65535 + sizeof(struct ether_vlan_header))
|
|
#define MSK_MAXRXSEGS 32
|
|
|
|
/*
|
|
* It seems that the hardware requires extra decriptors(LEs) to offload
|
|
* TCP/UDP checksum, VLAN hardware tag inserstion and TSO.
|
|
*
|
|
* 1 descriptor for TCP/UDP checksum offload.
|
|
* 1 descriptor VLAN hardware tag insertion.
|
|
* 1 descriptor for TSO(TCP Segmentation Offload)
|
|
* 1 descriptor for 64bits DMA : Not applicatable due to the use of
|
|
* BUS_SPACE_MAXADDR_32BIT in parent DMA tag creation.
|
|
*/
|
|
#define MSK_RESERVED_TX_DESC_CNT 3
|
|
|
|
/*
|
|
* Jumbo buffer stuff. Note that we must allocate more jumbo
|
|
* buffers than there are descriptors in the receive ring. This
|
|
* is because we don't know how long it will take for a packet
|
|
* to be released after we hand it off to the upper protocol
|
|
* layers. To be safe, we allocate 1.5 times the number of
|
|
* receive descriptors.
|
|
*/
|
|
#define MSK_JUMBO_FRAMELEN 9022
|
|
#define MSK_JUMBO_MTU (MSK_JUMBO_FRAMELEN-ETHER_HDR_LEN-ETHER_CRC_LEN)
|
|
#define MSK_MAX_FRAMELEN \
|
|
(ETHER_MAX_LEN + ETHER_VLAN_ENCAP_LEN - ETHER_CRC_LEN)
|
|
#define MSK_MIN_FRAMELEN (ETHER_MIN_LEN - ETHER_CRC_LEN)
|
|
#define MSK_JSLOTS ((MSK_RX_RING_CNT * 3) / 2)
|
|
|
|
#define MSK_JRAWLEN (MSK_JUMBO_FRAMELEN + ETHER_ALIGN)
|
|
#define MSK_JLEN (MSK_JRAWLEN + (sizeof(uint64_t) - \
|
|
(MSK_JRAWLEN % sizeof(uint64_t))))
|
|
#define MSK_JPAGESZ PAGE_SIZE
|
|
#define MSK_RESID \
|
|
(MSK_JPAGESZ - (MSK_JLEN * MSK_JSLOTS) % MSK_JPAGESZ)
|
|
#define MSK_JMEM ((MSK_JLEN * MSK_JSLOTS) + MSK_RESID)
|
|
|
|
struct msk_jpool_entry {
|
|
int slot;
|
|
SLIST_ENTRY(msk_jpool_entry) jpool_entries;
|
|
};
|
|
|
|
struct msk_txdesc {
|
|
struct mbuf *tx_m;
|
|
bus_dmamap_t tx_dmamap;
|
|
struct msk_tx_desc *tx_le;
|
|
};
|
|
|
|
struct msk_rxdesc {
|
|
struct mbuf *rx_m;
|
|
bus_dmamap_t rx_dmamap;
|
|
struct msk_rx_desc *rx_le;
|
|
};
|
|
|
|
struct msk_chain_data {
|
|
bus_dma_tag_t msk_parent_tag;
|
|
bus_dma_tag_t msk_tx_tag;
|
|
struct msk_txdesc msk_txdesc[MSK_TX_RING_CNT];
|
|
bus_dma_tag_t msk_rx_tag;
|
|
struct msk_rxdesc msk_rxdesc[MSK_RX_RING_CNT];
|
|
bus_dma_tag_t msk_tx_ring_tag;
|
|
bus_dma_tag_t msk_rx_ring_tag;
|
|
bus_dmamap_t msk_tx_ring_map;
|
|
bus_dmamap_t msk_rx_ring_map;
|
|
bus_dmamap_t msk_rx_sparemap;
|
|
bus_dma_tag_t msk_jumbo_rx_tag;
|
|
bus_dma_tag_t msk_jumbo_tag;
|
|
bus_dmamap_t msk_jumbo_map;
|
|
bus_dma_tag_t msk_jumbo_mtag;
|
|
caddr_t msk_jslots[MSK_JSLOTS];
|
|
struct msk_rxdesc msk_jumbo_rxdesc[MSK_JUMBO_RX_RING_CNT];
|
|
bus_dma_tag_t msk_jumbo_rx_ring_tag;
|
|
bus_dmamap_t msk_jumbo_rx_ring_map;
|
|
bus_dmamap_t msk_jumbo_rx_sparemap;
|
|
uint16_t msk_tso_mtu;
|
|
int msk_tx_prod;
|
|
int msk_tx_cons;
|
|
int msk_tx_cnt;
|
|
int msk_tx_put;
|
|
int msk_rx_cons;
|
|
int msk_rx_prod;
|
|
int msk_rx_putwm;
|
|
};
|
|
|
|
struct msk_ring_data {
|
|
struct msk_tx_desc *msk_tx_ring;
|
|
bus_addr_t msk_tx_ring_paddr;
|
|
struct msk_rx_desc *msk_rx_ring;
|
|
bus_addr_t msk_rx_ring_paddr;
|
|
struct msk_rx_desc *msk_jumbo_rx_ring;
|
|
bus_addr_t msk_jumbo_rx_ring_paddr;
|
|
void *msk_jumbo_buf;
|
|
bus_addr_t msk_jumbo_buf_paddr;
|
|
};
|
|
|
|
#define MSK_TX_RING_ADDR(sc, i) \
|
|
((sc)->msk_rdata.msk_tx_ring_paddr + sizeof(struct msk_tx_desc) * (i))
|
|
#define MSK_RX_RING_ADDR(sc, i) \
|
|
((sc)->msk_rdata.msk_rx_ring_paddr + sizeof(struct msk_rx_desc) * (i))
|
|
#define MSK_JUMBO_RX_RING_ADDR(sc, i) \
|
|
((sc)->msk_rdata.msk_jumbo_rx_ring_paddr + sizeof(struct msk_rx_desc) * (i))
|
|
|
|
#define MSK_TX_RING_SZ \
|
|
(sizeof(struct msk_tx_desc) * MSK_TX_RING_CNT)
|
|
#define MSK_RX_RING_SZ \
|
|
(sizeof(struct msk_rx_desc) * MSK_RX_RING_CNT)
|
|
#define MSK_JUMBO_RX_RING_SZ \
|
|
(sizeof(struct msk_rx_desc) * MSK_JUMBO_RX_RING_CNT)
|
|
#define MSK_STAT_RING_SZ \
|
|
(sizeof(struct msk_stat_desc) * MSK_STAT_RING_CNT)
|
|
|
|
#define MSK_INC(x, y) (x) = (x + 1) % y
|
|
|
|
#define MSK_PCI_BUS 0
|
|
#define MSK_PCIX_BUS 1
|
|
#define MSK_PEX_BUS 2
|
|
|
|
#define MSK_PROC_DEFAULT (MSK_RX_RING_CNT / 2)
|
|
#define MSK_PROC_MIN 30
|
|
#define MSK_PROC_MAX (MSK_RX_RING_CNT - 1)
|
|
|
|
#define MSK_TX_TIMEOUT 5
|
|
#define MSK_PUT_WM 10
|
|
|
|
/* Forward decl. */
|
|
struct msk_if_softc;
|
|
|
|
/* Softc for the Marvell Yukon II controller. */
|
|
struct msk_softc {
|
|
struct resource *msk_res[1]; /* I/O resource */
|
|
struct resource_spec *msk_res_spec;
|
|
struct resource *msk_irq[2]; /* IRQ resources */
|
|
struct resource_spec *msk_irq_spec;
|
|
void *msk_intrhand[2]; /* irq handler handle */
|
|
device_t msk_dev;
|
|
uint8_t msk_hw_id;
|
|
uint8_t msk_hw_rev;
|
|
uint8_t msk_bustype;
|
|
uint8_t msk_num_port;
|
|
int msk_ramsize; /* amount of SRAM on NIC */
|
|
uint32_t msk_pmd; /* physical media type */
|
|
uint32_t msk_coppertype;
|
|
uint32_t msk_intrmask;
|
|
uint32_t msk_intrhwemask;
|
|
int msk_suspended;
|
|
int msk_clock;
|
|
int msk_msi;
|
|
struct msk_if_softc *msk_if[2];
|
|
device_t msk_devs[2];
|
|
int msk_txqsize;
|
|
int msk_rxqsize;
|
|
int msk_txqstart[2];
|
|
int msk_txqend[2];
|
|
int msk_rxqstart[2];
|
|
int msk_rxqend[2];
|
|
bus_dma_tag_t msk_stat_tag;
|
|
bus_dmamap_t msk_stat_map;
|
|
struct msk_stat_desc *msk_stat_ring;
|
|
bus_addr_t msk_stat_ring_paddr;
|
|
int msk_process_limit;
|
|
int msk_stat_cons;
|
|
struct taskqueue *msk_tq;
|
|
struct task msk_int_task;
|
|
struct mtx msk_mtx;
|
|
};
|
|
|
|
#define MSK_LOCK(_sc) mtx_lock(&(_sc)->msk_mtx)
|
|
#define MSK_UNLOCK(_sc) mtx_unlock(&(_sc)->msk_mtx)
|
|
#define MSK_LOCK_ASSERT(_sc) mtx_assert(&(_sc)->msk_mtx, MA_OWNED)
|
|
#define MSK_IF_LOCK(_sc) MSK_LOCK((_sc)->msk_softc)
|
|
#define MSK_IF_UNLOCK(_sc) MSK_UNLOCK((_sc)->msk_softc)
|
|
#define MSK_IF_LOCK_ASSERT(_sc) MSK_LOCK_ASSERT((_sc)->msk_softc)
|
|
|
|
#define MSK_USECS(sc, us) ((sc)->msk_clock * (us))
|
|
|
|
/* Softc for each logical interface. */
|
|
struct msk_if_softc {
|
|
struct ifnet *msk_ifp; /* interface info */
|
|
device_t msk_miibus;
|
|
device_t msk_if_dev;
|
|
int32_t msk_port; /* port # on controller */
|
|
int msk_framesize;
|
|
int msk_phytype;
|
|
int msk_phyaddr;
|
|
int msk_link;
|
|
struct callout msk_tick_ch;
|
|
int msk_watchdog_timer;
|
|
uint32_t msk_txq; /* Tx. Async Queue offset */
|
|
uint32_t msk_txsq; /* Tx. Syn Queue offset */
|
|
uint32_t msk_rxq; /* Rx. Qeueue offset */
|
|
struct msk_chain_data msk_cdata;
|
|
struct msk_ring_data msk_rdata;
|
|
struct msk_softc *msk_softc; /* parent controller */
|
|
struct task msk_link_task;
|
|
struct task msk_tx_task;
|
|
int msk_if_flags;
|
|
int msk_detach;
|
|
uint16_t msk_vtag; /* VLAN tag id. */
|
|
SLIST_HEAD(__msk_jfreehead, msk_jpool_entry) msk_jfree_listhead;
|
|
SLIST_HEAD(__msk_jinusehead, msk_jpool_entry) msk_jinuse_listhead;
|
|
struct mtx msk_jlist_mtx;
|
|
};
|
|
|
|
#define MSK_JLIST_LOCK(_sc) mtx_lock(&(_sc)->msk_jlist_mtx)
|
|
#define MSK_JLIST_UNLOCK(_sc) mtx_unlock(&(_sc)->msk_jlist_mtx)
|
|
|
|
#define MSK_TIMEOUT 1000
|
|
#define MSK_PHY_POWERUP 1
|
|
#define MSK_PHY_POWERDOWN 0
|