adrian 56f51bf20a [ath_hal] Return failure if noise floor calibration fails. ... If we fail noise floor calibration then we may end up with a deaf NIC which we can't recover without a full chip reset. Earlier chips seem to get less stuck in this condition versus AR9280/later and AR9300/later, but whilst here just fix up the AR5212 era chips to also return NF calibration failures. This HAL routine would only return failure if the channel was not configured. This is a no-op until the driver side code for doing resets and the HAL code for being told about the reset type (and then handling it!) is implemented. Tested: * AR9280, STA mode * AR2425, STA mode * AR9380, STA mode		2018-06-08 18:21:57 +00:00
..
ar953x.ini	add missing initvals.	2015-11-29 18:14:18 +00:00
ar955x.ini
ar9300_aic.c
ar9300_ani.c	[ath_hal] Return failure if noise floor calibration fails.	2018-06-08 18:21:57 +00:00
ar9300_aphrodite10.ini
ar9300_attach.c	[ath_hal] quieten a bit of the boot messages - this stuff has been working for a while.	2016-09-12 04:58:59 +00:00
ar9300_beacon.c
ar9300_devid.h	Renumber copyright clause 4	2017-02-28 23:42:47 +00:00
ar9300_eeprom.c	Fix improper use of "its".	2016-11-08 23:59:41 +00:00
ar9300_freebsd_inc.h	[ath_hal] migrate the bluetooth definitions out from ah.h / ar9300_freebsd_inc.h.	2016-05-31 04:44:00 +00:00
ar9300_freebsd.c	[ath_hal] Return failure if noise floor calibration fails.	2018-06-08 18:21:57 +00:00
ar9300_freebsd.h
ar9300_gpio.c
ar9300_interrupts.c	[ath_hal] add extra debugging for MCI interrupts.	2016-06-01 03:17:36 +00:00
ar9300_jupiter10.ini
ar9300_jupiter20.ini
ar9300_keycache.c
ar9300_mci.c	[ath_hal] convert the MCI code over to work on Jupiter 2.1.	2016-06-05 02:15:29 +00:00
ar9300_misc.c	[ath_hal] [ar9300] link in the CAC enable/diable methods and expose it via the HAL.	2017-02-03 05:15:35 +00:00
ar9300_osprey22_scoemu.ini
ar9300_osprey22.ini
ar9300_paprd.c
ar9300_phy.c
ar9300_power.c
ar9300_radar.c	[ath_hal] [ar9300] initial radar detection glue.	2017-02-02 09:19:57 +00:00
ar9300_radio.c	Fix the build	2015-11-30 08:02:52 +00:00
ar9300_raw_adc_capture.c
ar9300_recv_ds.c	[ath_hal] add locationing / tx-beamforming RX status descriptor decoding.	2016-07-08 22:39:37 +00:00
ar9300_recv.c	Add initial support for the QCA953x SoC (honeybee) wifi.	2015-11-29 05:47:52 +00:00
ar9300_reset.c	[ath_hal] Return failure if noise floor calibration fails.	2018-06-08 18:21:57 +00:00
ar9300_rtt.c
ar9300_sim.c
ar9300_sim.h
ar9300_spectral.c	[ath_hal] [ar9300] initial hacks to make spectral scan working on AR9380 and later NICs.	2017-02-02 05:29:22 +00:00
ar9300_stub_funcs.c
ar9300_stub_funcs.h
ar9300_stub.c
ar9300_stub.h
ar9300_timer.c
ar9300_tx99_tgt.c
ar9300_txbf_cal.c
ar9300_txbf.c
ar9300_txbf.h
ar9300_xmit_ds.c	[ath_hal] Add setting positioning bit and clear sounding-disable bit.	2016-07-08 22:37:52 +00:00
ar9300_xmit.c	[ar9300] don't program a negative readytime.	2016-08-09 01:05:29 +00:00
ar9300.h	[ath_hal] migrate the shared HAL_RESET_* pieces out into ath_hal.	2018-05-25 01:27:39 +00:00
ar9300desc.h
ar9300eep.h	Quiesce a couple pages of clang warnings with a cast. Duplicates	2018-05-18 17:23:23 +00:00
ar9300paprd.h
ar9300phy.h	[ath_hal] [ar9300] initial radar detection glue.	2017-02-02 09:19:57 +00:00
ar9300radar.h
ar9300reg.h	[ath_hal] add a _S so FSP (frame scheduling policy) can be set/read via SM/MS macros.	2016-06-08 16:21:38 +00:00
ar9300template_ap121.h
ar9300template_aphrodite.h
ar9300template_cus157.h
ar9300template_generic.h
ar9300template_hb112.h
ar9300template_hb116.h
ar9300template_osprey_k31.h
ar9300template_wasp_2.h
ar9300template_wasp_k31.h
ar9300template_xb112.h
ar9300template_xb113.h
ar9330_11.ini
ar9330_12.ini
ar9340.ini
ar9462_2p0_initvals.h	[ath_hal] Make the AR9462 2.0 initvals from ath9k compile.	2016-06-05 01:42:37 +00:00
ar9462_2p1_initvals.h	u32 -> uint32_t.	2015-11-29 05:42:18 +00:00
ar9485_1_1.ini
ar9485.ini
ar9580.ini
eeprom.diff
osprey_reg_map_macro.h
osprey_reg_map.h
poseidon_reg_map_macro.h
scorpion_reg_map_macro.h
scorpion_reg_map.h
sources
wasp_reg_map.h