723 lines
19 KiB
C
723 lines
19 KiB
C
/* $FreeBSD$ */
|
|
/*
|
|
* Mailbox and Queue Entry Definitions for for Qlogic ISP SCSI adapters.
|
|
*
|
|
* Copyright (c) 1997, 1998, 1999, 2000 by Matthew Jacob
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice immediately at the beginning of the file, without modification,
|
|
* this list of conditions, and the following disclaimer.
|
|
* 2. The name of the author may not be used to endorse or promote products
|
|
* derived from this software without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
|
|
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
|
|
* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR
|
|
* ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
|
|
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
|
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
|
|
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
|
|
* SUCH DAMAGE.
|
|
*
|
|
*/
|
|
#ifndef _ISPMBOX_H
|
|
#define _ISPMBOX_H
|
|
|
|
/*
|
|
* Mailbox Command Opcodes
|
|
*/
|
|
|
|
#define MBOX_NO_OP 0x0000
|
|
#define MBOX_LOAD_RAM 0x0001
|
|
#define MBOX_EXEC_FIRMWARE 0x0002
|
|
#define MBOX_DUMP_RAM 0x0003
|
|
#define MBOX_WRITE_RAM_WORD 0x0004
|
|
#define MBOX_READ_RAM_WORD 0x0005
|
|
#define MBOX_MAILBOX_REG_TEST 0x0006
|
|
#define MBOX_VERIFY_CHECKSUM 0x0007
|
|
#define MBOX_ABOUT_FIRMWARE 0x0008
|
|
/* 9 */
|
|
/* a */
|
|
/* b */
|
|
/* c */
|
|
/* d */
|
|
#define MBOX_CHECK_FIRMWARE 0x000e
|
|
/* f */
|
|
#define MBOX_INIT_REQ_QUEUE 0x0010
|
|
#define MBOX_INIT_RES_QUEUE 0x0011
|
|
#define MBOX_EXECUTE_IOCB 0x0012
|
|
#define MBOX_WAKE_UP 0x0013
|
|
#define MBOX_STOP_FIRMWARE 0x0014
|
|
#define MBOX_ABORT 0x0015
|
|
#define MBOX_ABORT_DEVICE 0x0016
|
|
#define MBOX_ABORT_TARGET 0x0017
|
|
#define MBOX_BUS_RESET 0x0018
|
|
#define MBOX_STOP_QUEUE 0x0019
|
|
#define MBOX_START_QUEUE 0x001a
|
|
#define MBOX_SINGLE_STEP_QUEUE 0x001b
|
|
#define MBOX_ABORT_QUEUE 0x001c
|
|
#define MBOX_GET_DEV_QUEUE_STATUS 0x001d
|
|
/* 1e */
|
|
#define MBOX_GET_FIRMWARE_STATUS 0x001f
|
|
#define MBOX_GET_INIT_SCSI_ID 0x0020
|
|
#define MBOX_GET_SELECT_TIMEOUT 0x0021
|
|
#define MBOX_GET_RETRY_COUNT 0x0022
|
|
#define MBOX_GET_TAG_AGE_LIMIT 0x0023
|
|
#define MBOX_GET_CLOCK_RATE 0x0024
|
|
#define MBOX_GET_ACT_NEG_STATE 0x0025
|
|
#define MBOX_GET_ASYNC_DATA_SETUP_TIME 0x0026
|
|
#define MBOX_GET_SBUS_PARAMS 0x0027
|
|
#define MBOX_GET_TARGET_PARAMS 0x0028
|
|
#define MBOX_GET_DEV_QUEUE_PARAMS 0x0029
|
|
#define MBOX_GET_RESET_DELAY_PARAMS 0x002a
|
|
/* 2b */
|
|
/* 2c */
|
|
/* 2d */
|
|
/* 2e */
|
|
/* 2f */
|
|
#define MBOX_SET_INIT_SCSI_ID 0x0030
|
|
#define MBOX_SET_SELECT_TIMEOUT 0x0031
|
|
#define MBOX_SET_RETRY_COUNT 0x0032
|
|
#define MBOX_SET_TAG_AGE_LIMIT 0x0033
|
|
#define MBOX_SET_CLOCK_RATE 0x0034
|
|
#define MBOX_SET_ACT_NEG_STATE 0x0035
|
|
#define MBOX_SET_ASYNC_DATA_SETUP_TIME 0x0036
|
|
#define MBOX_SET_SBUS_CONTROL_PARAMS 0x0037
|
|
#define MBOX_SET_PCI_PARAMETERS 0x0037
|
|
#define MBOX_SET_TARGET_PARAMS 0x0038
|
|
#define MBOX_SET_DEV_QUEUE_PARAMS 0x0039
|
|
#define MBOX_SET_RESET_DELAY_PARAMS 0x003a
|
|
/* 3b */
|
|
/* 3c */
|
|
/* 3d */
|
|
/* 3e */
|
|
/* 3f */
|
|
#define MBOX_RETURN_BIOS_BLOCK_ADDR 0x0040
|
|
#define MBOX_WRITE_FOUR_RAM_WORDS 0x0041
|
|
#define MBOX_EXEC_BIOS_IOCB 0x0042
|
|
#define MBOX_SET_FW_FEATURES 0x004a
|
|
#define MBOX_GET_FW_FEATURES 0x004b
|
|
#define FW_FEATURE_LVD_NOTIFY 0x2
|
|
#define FW_FEATURE_FAST_POST 0x1
|
|
|
|
#define MBOX_ENABLE_TARGET_MODE 0x55
|
|
#define ENABLE_TARGET_FLAG 0x8000
|
|
|
|
/* These are for the ISP2100 FC cards */
|
|
#define MBOX_GET_LOOP_ID 0x20
|
|
#define MBOX_GET_RESOURCE_COUNT 0x42
|
|
#define MBOX_EXEC_COMMAND_IOCB_A64 0x54
|
|
#define MBOX_INIT_FIRMWARE 0x60
|
|
#define MBOX_GET_INIT_CONTROL_BLOCK 0x61
|
|
#define MBOX_INIT_LIP 0x62
|
|
#define MBOX_GET_FC_AL_POSITION_MAP 0x63
|
|
#define MBOX_GET_PORT_DB 0x64
|
|
#define MBOX_CLEAR_ACA 0x65
|
|
#define MBOX_TARGET_RESET 0x66
|
|
#define MBOX_CLEAR_TASK_SET 0x67
|
|
#define MBOX_ABORT_TASK_SET 0x68
|
|
#define MBOX_GET_FW_STATE 0x69
|
|
#define MBOX_GET_PORT_NAME 0x6a
|
|
#define MBOX_GET_LINK_STATUS 0x6b
|
|
#define MBOX_INIT_LIP_RESET 0x6c
|
|
#define MBOX_SEND_SNS 0x6e
|
|
#define MBOX_FABRIC_LOGIN 0x6f
|
|
#define MBOX_SEND_CHANGE_REQUEST 0x70
|
|
#define MBOX_FABRIC_LOGOUT 0x71
|
|
#define MBOX_INIT_LIP_LOGIN 0x72
|
|
|
|
#define ISP2100_SET_PCI_PARAM 0x00ff
|
|
|
|
#define MBOX_BUSY 0x04
|
|
|
|
typedef struct {
|
|
u_int16_t param[8];
|
|
} mbreg_t;
|
|
|
|
/*
|
|
* Mailbox Command Complete Status Codes
|
|
*/
|
|
#define MBOX_COMMAND_COMPLETE 0x4000
|
|
#define MBOX_INVALID_COMMAND 0x4001
|
|
#define MBOX_HOST_INTERFACE_ERROR 0x4002
|
|
#define MBOX_TEST_FAILED 0x4003
|
|
#define MBOX_COMMAND_ERROR 0x4005
|
|
#define MBOX_COMMAND_PARAM_ERROR 0x4006
|
|
#define MBOX_PORT_ID_USED 0x4007
|
|
#define MBOX_LOOP_ID_USED 0x4008
|
|
#define MBOX_ALL_IDS_USED 0x4009
|
|
#define MBOX_NOT_LOGGED_IN 0x400A
|
|
#define MBLOGALL 0x000f
|
|
#define MBLOGNONE 0x0000
|
|
#define MBLOGMASK(x) ((x) & 0xf)
|
|
|
|
/*
|
|
* Asynchronous event status codes
|
|
*/
|
|
#define ASYNC_BUS_RESET 0x8001
|
|
#define ASYNC_SYSTEM_ERROR 0x8002
|
|
#define ASYNC_RQS_XFER_ERR 0x8003
|
|
#define ASYNC_RSP_XFER_ERR 0x8004
|
|
#define ASYNC_QWAKEUP 0x8005
|
|
#define ASYNC_TIMEOUT_RESET 0x8006
|
|
#define ASYNC_DEVICE_RESET 0x8007
|
|
#define ASYNC_EXTMSG_UNDERRUN 0x800A
|
|
#define ASYNC_SCAM_INT 0x800B
|
|
#define ASYNC_HUNG_SCSI 0x800C
|
|
#define ASYNC_KILLED_BUS 0x800D
|
|
#define ASYNC_BUS_TRANSIT 0x800E /* LVD -> HVD, eg. */
|
|
#define ASYNC_CMD_CMPLT 0x8020
|
|
#define ASYNC_CTIO_DONE 0x8021
|
|
|
|
/* for ISP2100 only */
|
|
#define ASYNC_LIP_OCCURRED 0x8010
|
|
#define ASYNC_LOOP_UP 0x8011
|
|
#define ASYNC_LOOP_DOWN 0x8012
|
|
#define ASYNC_LOOP_RESET 0x8013
|
|
#define ASYNC_PDB_CHANGED 0x8014
|
|
#define ASYNC_CHANGE_NOTIFY 0x8015
|
|
|
|
/* for ISP2200 only */
|
|
#define ASYNC_PTPMODE 0x8030
|
|
#define ASYNC_CONNMODE 0x8036
|
|
#define ISP_CONN_LOOP 1
|
|
#define ISP_CONN_PTP 2
|
|
#define ISP_CONN_BADLIP 3
|
|
#define ISP_CONN_FATAL 4
|
|
#define ISP_CONN_LOOPBACK 5
|
|
|
|
/*
|
|
* Command Structure Definitions
|
|
*/
|
|
|
|
typedef struct {
|
|
u_int32_t ds_base;
|
|
u_int32_t ds_count;
|
|
} ispds_t;
|
|
|
|
#define _ISP_SWAP8(a, b) { \
|
|
u_int8_t tmp; \
|
|
tmp = a; \
|
|
a = b; \
|
|
b = tmp; \
|
|
}
|
|
|
|
/*
|
|
* These elements get swizzled around for SBus instances.
|
|
*/
|
|
typedef struct {
|
|
u_int8_t rqs_entry_type;
|
|
u_int8_t rqs_entry_count;
|
|
u_int8_t rqs_seqno;
|
|
u_int8_t rqs_flags;
|
|
} isphdr_t;
|
|
/*
|
|
* There are no (for all intents and purposes) non-sparc SBus machines
|
|
*/
|
|
#ifdef __sparc__
|
|
#define ISP_SBUSIFY_ISPHDR(isp, hdrp) \
|
|
if ((isp)->isp_bustype == ISP_BT_SBUS) { \
|
|
_ISP_SWAP8((hdrp)->rqs_entry_count, (hdrp)->rqs_entry_type); \
|
|
_ISP_SWAP8((hdrp)->rqs_flags, (hdrp)->rqs_seqno); \
|
|
}
|
|
#else
|
|
#define ISP_SBUSIFY_ISPHDR(a, b)
|
|
#endif
|
|
|
|
/* RQS Flag definitions */
|
|
#define RQSFLAG_CONTINUATION 0x01
|
|
#define RQSFLAG_FULL 0x02
|
|
#define RQSFLAG_BADHEADER 0x04
|
|
#define RQSFLAG_BADPACKET 0x08
|
|
|
|
/* RQS entry_type definitions */
|
|
#define RQSTYPE_REQUEST 0x01
|
|
#define RQSTYPE_DATASEG 0x02
|
|
#define RQSTYPE_RESPONSE 0x03
|
|
#define RQSTYPE_MARKER 0x04
|
|
#define RQSTYPE_CMDONLY 0x05
|
|
#define RQSTYPE_ATIO 0x06 /* Target Mode */
|
|
#define RQSTYPE_CTIO 0x07 /* Target Mode */
|
|
#define RQSTYPE_SCAM 0x08
|
|
#define RQSTYPE_A64 0x09
|
|
#define RQSTYPE_A64_CONT 0x0a
|
|
#define RQSTYPE_ENABLE_LUN 0x0b /* Target Mode */
|
|
#define RQSTYPE_MODIFY_LUN 0x0c /* Target Mode */
|
|
#define RQSTYPE_NOTIFY 0x0d /* Target Mode */
|
|
#define RQSTYPE_NOTIFY_ACK 0x0e /* Target Mode */
|
|
#define RQSTYPE_CTIO1 0x0f /* Target Mode */
|
|
#define RQSTYPE_STATUS_CONT 0x10
|
|
#define RQSTYPE_T2RQS 0x11
|
|
|
|
#define RQSTYPE_T4RQS 0x15
|
|
#define RQSTYPE_ATIO2 0x16
|
|
#define RQSTYPE_CTIO2 0x17
|
|
#define RQSTYPE_CSET0 0x18
|
|
#define RQSTYPE_T3RQS 0x19
|
|
|
|
#define RQSTYPE_CTIO3 0x1f
|
|
|
|
|
|
#define ISP_RQDSEG 4
|
|
typedef struct {
|
|
isphdr_t req_header;
|
|
u_int32_t req_handle;
|
|
u_int8_t req_lun_trn;
|
|
u_int8_t req_target;
|
|
u_int16_t req_cdblen;
|
|
#define req_modifier req_cdblen /* marker packet */
|
|
u_int16_t req_flags;
|
|
u_int16_t req_reserved;
|
|
u_int16_t req_time;
|
|
u_int16_t req_seg_count;
|
|
u_int8_t req_cdb[12];
|
|
ispds_t req_dataseg[ISP_RQDSEG];
|
|
} ispreq_t;
|
|
|
|
/*
|
|
* A request packet can also be a marker packet.
|
|
*/
|
|
#define SYNC_DEVICE 0
|
|
#define SYNC_TARGET 1
|
|
#define SYNC_ALL 2
|
|
|
|
/*
|
|
* There are no (for all intents and purposes) non-sparc SBus machines
|
|
*/
|
|
#ifdef __sparc__
|
|
#define ISP_SBUSIFY_ISPREQ(isp, rqp) \
|
|
if ((isp)->isp_bustype == ISP_BT_SBUS) { \
|
|
_ISP_SWAP8((rqp)->req_target, (rqp)->req_lun_trn); \
|
|
}
|
|
#else
|
|
#define ISP_SBUSIFY_ISPREQ(a, b)
|
|
#endif
|
|
|
|
#define ISP_RQDSEG_T2 3
|
|
typedef struct {
|
|
isphdr_t req_header;
|
|
u_int32_t req_handle;
|
|
u_int8_t req_lun_trn;
|
|
u_int8_t req_target;
|
|
u_int16_t req_scclun;
|
|
u_int16_t req_flags;
|
|
u_int16_t _res2;
|
|
u_int16_t req_time;
|
|
u_int16_t req_seg_count;
|
|
u_int32_t req_cdb[4];
|
|
u_int32_t req_totalcnt;
|
|
ispds_t req_dataseg[ISP_RQDSEG_T2];
|
|
} ispreqt2_t;
|
|
|
|
/* req_flag values */
|
|
#define REQFLAG_NODISCON 0x0001
|
|
#define REQFLAG_HTAG 0x0002
|
|
#define REQFLAG_OTAG 0x0004
|
|
#define REQFLAG_STAG 0x0008
|
|
#define REQFLAG_TARGET_RTN 0x0010
|
|
|
|
#define REQFLAG_NODATA 0x0000
|
|
#define REQFLAG_DATA_IN 0x0020
|
|
#define REQFLAG_DATA_OUT 0x0040
|
|
#define REQFLAG_DATA_UNKNOWN 0x0060
|
|
|
|
#define REQFLAG_DISARQ 0x0100
|
|
#define REQFLAG_FRC_ASYNC 0x0200
|
|
#define REQFLAG_FRC_SYNC 0x0400
|
|
#define REQFLAG_FRC_WIDE 0x0800
|
|
#define REQFLAG_NOPARITY 0x1000
|
|
#define REQFLAG_STOPQ 0x2000
|
|
#define REQFLAG_XTRASNS 0x4000
|
|
#define REQFLAG_PRIORITY 0x8000
|
|
|
|
typedef struct {
|
|
isphdr_t req_header;
|
|
u_int32_t req_handle;
|
|
u_int8_t req_lun_trn;
|
|
u_int8_t req_target;
|
|
u_int16_t req_cdblen;
|
|
u_int16_t req_flags;
|
|
u_int16_t _res1;
|
|
u_int16_t req_time;
|
|
u_int16_t req_seg_count;
|
|
u_int8_t req_cdb[44];
|
|
} ispextreq_t;
|
|
|
|
#define ISP_CDSEG 7
|
|
typedef struct {
|
|
isphdr_t req_header;
|
|
u_int32_t _res1;
|
|
ispds_t req_dataseg[ISP_CDSEG];
|
|
} ispcontreq_t;
|
|
|
|
typedef struct {
|
|
isphdr_t req_header;
|
|
u_int32_t req_handle;
|
|
u_int16_t req_scsi_status;
|
|
u_int16_t req_completion_status;
|
|
u_int16_t req_state_flags;
|
|
u_int16_t req_status_flags;
|
|
u_int16_t req_time;
|
|
#define req_response_len req_time /* FC only */
|
|
u_int16_t req_sense_len;
|
|
u_int32_t req_resid;
|
|
u_int8_t req_response[8]; /* FC only */
|
|
u_int8_t req_sense_data[32];
|
|
} ispstatusreq_t;
|
|
|
|
/*
|
|
* For Qlogic 2X00, the high order byte of SCSI status has
|
|
* additional meaning.
|
|
*/
|
|
#define RQCS_RU 0x800 /* Residual Under */
|
|
#define RQCS_RO 0x400 /* Residual Over */
|
|
#define RQCS_RESID (RQCS_RU|RQCS_RO)
|
|
#define RQCS_SV 0x200 /* Sense Length Valid */
|
|
#define RQCS_RV 0x100 /* FCP Response Length Valid */
|
|
|
|
/*
|
|
* Completion Status Codes.
|
|
*/
|
|
#define RQCS_COMPLETE 0x0000
|
|
#define RQCS_DMA_ERROR 0x0002
|
|
#define RQCS_RESET_OCCURRED 0x0004
|
|
#define RQCS_ABORTED 0x0005
|
|
#define RQCS_TIMEOUT 0x0006
|
|
#define RQCS_DATA_OVERRUN 0x0007
|
|
#define RQCS_DATA_UNDERRUN 0x0015
|
|
#define RQCS_QUEUE_FULL 0x001C
|
|
|
|
/* 1X00 Only Completion Codes */
|
|
#define RQCS_INCOMPLETE 0x0001
|
|
#define RQCS_TRANSPORT_ERROR 0x0003
|
|
#define RQCS_COMMAND_OVERRUN 0x0008
|
|
#define RQCS_STATUS_OVERRUN 0x0009
|
|
#define RQCS_BAD_MESSAGE 0x000a
|
|
#define RQCS_NO_MESSAGE_OUT 0x000b
|
|
#define RQCS_EXT_ID_FAILED 0x000c
|
|
#define RQCS_IDE_MSG_FAILED 0x000d
|
|
#define RQCS_ABORT_MSG_FAILED 0x000e
|
|
#define RQCS_REJECT_MSG_FAILED 0x000f
|
|
#define RQCS_NOP_MSG_FAILED 0x0010
|
|
#define RQCS_PARITY_ERROR_MSG_FAILED 0x0011
|
|
#define RQCS_DEVICE_RESET_MSG_FAILED 0x0012
|
|
#define RQCS_ID_MSG_FAILED 0x0013
|
|
#define RQCS_UNEXP_BUS_FREE 0x0014
|
|
#define RQCS_XACT_ERR1 0x0018
|
|
#define RQCS_XACT_ERR2 0x0019
|
|
#define RQCS_XACT_ERR3 0x001A
|
|
#define RQCS_BAD_ENTRY 0x001B
|
|
#define RQCS_PHASE_SKIPPED 0x001D
|
|
#define RQCS_ARQS_FAILED 0x001E
|
|
#define RQCS_WIDE_FAILED 0x001F
|
|
#define RQCS_SYNCXFER_FAILED 0x0020
|
|
#define RQCS_LVD_BUSERR 0x0021
|
|
|
|
/* 2X00 Only Completion Codes */
|
|
#define RQCS_PORT_UNAVAILABLE 0x0028
|
|
#define RQCS_PORT_LOGGED_OUT 0x0029
|
|
#define RQCS_PORT_CHANGED 0x002A
|
|
#define RQCS_PORT_BUSY 0x002B
|
|
|
|
/*
|
|
* 1X00 specific State Flags
|
|
*/
|
|
#define RQSF_GOT_BUS 0x0100
|
|
#define RQSF_GOT_TARGET 0x0200
|
|
#define RQSF_SENT_CDB 0x0400
|
|
#define RQSF_XFRD_DATA 0x0800
|
|
#define RQSF_GOT_STATUS 0x1000
|
|
#define RQSF_GOT_SENSE 0x2000
|
|
#define RQSF_XFER_COMPLETE 0x4000
|
|
|
|
/*
|
|
* 2X00 specific State Flags
|
|
* (same as 1X00 except RQSF_GOT_BUS/RQSF_GOT_TARGET are not available)
|
|
*/
|
|
#define RQSF_DATA_IN 0x0020
|
|
#define RQSF_DATA_OUT 0x0040
|
|
#define RQSF_STAG 0x0008
|
|
#define RQSF_OTAG 0x0004
|
|
#define RQSF_HTAG 0x0002
|
|
/*
|
|
* 1X00 Status Flags
|
|
*/
|
|
#define RQSTF_DISCONNECT 0x0001
|
|
#define RQSTF_SYNCHRONOUS 0x0002
|
|
#define RQSTF_PARITY_ERROR 0x0004
|
|
#define RQSTF_BUS_RESET 0x0008
|
|
#define RQSTF_DEVICE_RESET 0x0010
|
|
#define RQSTF_ABORTED 0x0020
|
|
#define RQSTF_TIMEOUT 0x0040
|
|
#define RQSTF_NEGOTIATION 0x0080
|
|
|
|
/*
|
|
* 2X00 specific state flags
|
|
*/
|
|
/* RQSF_SENT_CDB */
|
|
/* RQSF_XFRD_DATA */
|
|
/* RQSF_GOT_STATUS */
|
|
/* RQSF_XFER_COMPLETE */
|
|
|
|
/*
|
|
* 2X00 specific status flags
|
|
*/
|
|
/* RQSTF_ABORTED */
|
|
/* RQSTF_TIMEOUT */
|
|
#define RQSTF_DMA_ERROR 0x0080
|
|
#define RQSTF_LOGOUT 0x2000
|
|
|
|
/*
|
|
* Miscellaneous
|
|
*/
|
|
#ifndef ISP_EXEC_THROTTLE
|
|
#define ISP_EXEC_THROTTLE 16
|
|
#endif
|
|
|
|
/*
|
|
* FC (ISP2100) specific data structures
|
|
*/
|
|
|
|
/*
|
|
* Initialization Control Block
|
|
*
|
|
* Version One (prime) format.
|
|
*/
|
|
typedef struct isp_icb {
|
|
u_int8_t icb_version;
|
|
u_int8_t _reserved0;
|
|
u_int16_t icb_fwoptions;
|
|
u_int16_t icb_maxfrmlen;
|
|
u_int16_t icb_maxalloc;
|
|
u_int16_t icb_execthrottle;
|
|
u_int8_t icb_retry_count;
|
|
u_int8_t icb_retry_delay;
|
|
u_int8_t icb_portname[8];
|
|
u_int16_t icb_hardaddr;
|
|
u_int8_t icb_iqdevtype;
|
|
u_int8_t icb_logintime;
|
|
u_int8_t icb_nodename[8];
|
|
u_int16_t icb_rqstout;
|
|
u_int16_t icb_rspnsin;
|
|
u_int16_t icb_rqstqlen;
|
|
u_int16_t icb_rsltqlen;
|
|
u_int16_t icb_rqstaddr[4];
|
|
u_int16_t icb_respaddr[4];
|
|
u_int16_t icb_lunenables;
|
|
u_int8_t icb_ccnt;
|
|
u_int8_t icb_icnt;
|
|
u_int16_t icb_lunetimeout;
|
|
u_int16_t _reserved1;
|
|
u_int16_t icb_xfwoptions;
|
|
u_int8_t icb_racctimer;
|
|
u_int8_t icb_idelaytimer;
|
|
u_int16_t icb_zfwoptions;
|
|
u_int16_t _reserved2[13];
|
|
} isp_icb_t;
|
|
#define ICB_VERSION1 1
|
|
|
|
#define ICBOPT_HARD_ADDRESS 0x0001
|
|
#define ICBOPT_FAIRNESS 0x0002
|
|
#define ICBOPT_FULL_DUPLEX 0x0004
|
|
#define ICBOPT_FAST_POST 0x0008
|
|
#define ICBOPT_TGT_ENABLE 0x0010
|
|
#define ICBOPT_INI_DISABLE 0x0020
|
|
#define ICBOPT_INI_ADISC 0x0040
|
|
#define ICBOPT_INI_TGTTYPE 0x0080
|
|
#define ICBOPT_PDBCHANGE_AE 0x0100
|
|
#define ICBOPT_NOLIP 0x0200
|
|
#define ICBOPT_SRCHDOWN 0x0400
|
|
#define ICBOPT_PREVLOOP 0x0800
|
|
#define ICBOPT_STOP_ON_QFULL 0x1000
|
|
#define ICBOPT_FULL_LOGIN 0x2000
|
|
#define ICBOPT_USE_PORTNAME 0x4000
|
|
#define ICBOPT_EXTENDED 0x8000
|
|
|
|
#define ICBXOPT_CLASS2_ACK0 0x0200
|
|
#define ICBXOPT_CLASS2 0x0100
|
|
#define ICBXOPT_LOOP_ONLY (0 << 4)
|
|
#define ICBXOPT_PTP_ONLY (1 << 4)
|
|
#define ICBXOPT_LOOP_2_PTP (2 << 4)
|
|
#define ICBXOPT_PTP_2_LOOP (3 << 4)
|
|
|
|
#define ICBXOPT_RIO_OFF 0
|
|
#define ICBXOPT_RIO_16BIT 1
|
|
#define ICBXOPT_RIO_32BIT 2
|
|
#define ICBXOPT_RIO_16BIT_DELAY 3
|
|
#define ICBXOPT_RIO_32BIT_DELAY 4
|
|
|
|
|
|
|
|
#define ICB_MIN_FRMLEN 256
|
|
#define ICB_MAX_FRMLEN 2112
|
|
#define ICB_DFLT_FRMLEN 1024
|
|
#define ICB_DFLT_ALLOC 256
|
|
#define ICB_DFLT_THROTTLE 16
|
|
#define ICB_DFLT_RDELAY 5
|
|
#define ICB_DFLT_RCOUNT 3
|
|
|
|
|
|
#define RQRSP_ADDR0015 0
|
|
#define RQRSP_ADDR1631 1
|
|
#define RQRSP_ADDR3247 2
|
|
#define RQRSP_ADDR4863 3
|
|
|
|
|
|
#define ICB_NNM0 7
|
|
#define ICB_NNM1 6
|
|
#define ICB_NNM2 5
|
|
#define ICB_NNM3 4
|
|
#define ICB_NNM4 3
|
|
#define ICB_NNM5 2
|
|
#define ICB_NNM6 1
|
|
#define ICB_NNM7 0
|
|
|
|
#define MAKE_NODE_NAME_FROM_WWN(array, wwn) \
|
|
array[ICB_NNM0] = (u_int8_t) ((wwn >> 0) & 0xff), \
|
|
array[ICB_NNM1] = (u_int8_t) ((wwn >> 8) & 0xff), \
|
|
array[ICB_NNM2] = (u_int8_t) ((wwn >> 16) & 0xff), \
|
|
array[ICB_NNM3] = (u_int8_t) ((wwn >> 24) & 0xff), \
|
|
array[ICB_NNM4] = (u_int8_t) ((wwn >> 32) & 0xff), \
|
|
array[ICB_NNM5] = (u_int8_t) ((wwn >> 40) & 0xff), \
|
|
array[ICB_NNM6] = (u_int8_t) ((wwn >> 48) & 0xff), \
|
|
array[ICB_NNM7] = (u_int8_t) ((wwn >> 56) & 0xff)
|
|
|
|
/*
|
|
* FC-AL Position Map
|
|
*
|
|
* This is an at most 128 byte map that returns either
|
|
* the LILP or Firmware generated list of ports.
|
|
*
|
|
* We deviate a bit from the returned qlogic format to
|
|
* use an extra bit to say whether this was a LILP or
|
|
* f/w generated map.
|
|
*/
|
|
typedef struct {
|
|
u_int8_t fwmap : 1,
|
|
count : 7;
|
|
u_int8_t map[127];
|
|
} fcpos_map_t;
|
|
|
|
/*
|
|
* Port Data Base Element
|
|
*/
|
|
|
|
typedef struct {
|
|
u_int16_t pdb_options;
|
|
u_int8_t pdb_mstate;
|
|
u_int8_t pdb_sstate;
|
|
#define BITS2WORD(x) ((x)[0] << 16 | (x)[3] << 8 | (x)[2])
|
|
u_int8_t pdb_hardaddr_bits[4];
|
|
u_int8_t pdb_portid_bits[4];
|
|
u_int8_t pdb_nodename[8];
|
|
u_int8_t pdb_portname[8];
|
|
u_int16_t pdb_execthrottle;
|
|
u_int16_t pdb_exec_count;
|
|
u_int8_t pdb_retry_count;
|
|
u_int8_t pdb_retry_delay;
|
|
u_int16_t pdb_resalloc;
|
|
u_int16_t pdb_curalloc;
|
|
u_int16_t pdb_qhead;
|
|
u_int16_t pdb_qtail;
|
|
u_int16_t pdb_tl_next;
|
|
u_int16_t pdb_tl_last;
|
|
u_int16_t pdb_features; /* PLOGI, Common Service */
|
|
u_int16_t pdb_pconcurrnt; /* PLOGI, Common Service */
|
|
u_int16_t pdb_roi; /* PLOGI, Common Service */
|
|
u_int8_t pdb_target;
|
|
u_int8_t pdb_initiator; /* PLOGI, Class 3 Control Flags */
|
|
u_int16_t pdb_rdsiz; /* PLOGI, Class 3 */
|
|
u_int16_t pdb_ncseq; /* PLOGI, Class 3 */
|
|
u_int16_t pdb_noseq; /* PLOGI, Class 3 */
|
|
u_int16_t pdb_labrtflg;
|
|
u_int16_t pdb_lstopflg;
|
|
u_int16_t pdb_sqhead;
|
|
u_int16_t pdb_sqtail;
|
|
u_int16_t pdb_ptimer;
|
|
u_int16_t pdb_nxt_seqid;
|
|
u_int16_t pdb_fcount;
|
|
u_int16_t pdb_prli_len;
|
|
u_int16_t pdb_prli_svc0;
|
|
u_int16_t pdb_prli_svc3;
|
|
u_int16_t pdb_loopid;
|
|
u_int16_t pdb_il_ptr;
|
|
u_int16_t pdb_sl_ptr;
|
|
} isp_pdb_t;
|
|
|
|
#define PDB_OPTIONS_XMITTING (1<<11)
|
|
#define PDB_OPTIONS_LNKXMIT (1<<10)
|
|
#define PDB_OPTIONS_ABORTED (1<<9)
|
|
#define PDB_OPTIONS_ADISC (1<<1)
|
|
|
|
#define PDB_STATE_DISCOVERY 0
|
|
#define PDB_STATE_WDISC_ACK 1
|
|
#define PDB_STATE_PLOGI 2
|
|
#define PDB_STATE_PLOGI_ACK 3
|
|
#define PDB_STATE_PRLI 4
|
|
#define PDB_STATE_PRLI_ACK 5
|
|
#define PDB_STATE_LOGGED_IN 6
|
|
#define PDB_STATE_PORT_UNAVAIL 7
|
|
#define PDB_STATE_PRLO 8
|
|
#define PDB_STATE_PRLO_ACK 9
|
|
#define PDB_STATE_PLOGO 10
|
|
#define PDB_STATE_PLOG_ACK 11
|
|
|
|
#define SVC3_TGT_ROLE 0x10
|
|
#define SVC3_INI_ROLE 0x20
|
|
#define SVC3_ROLE_MASK 0x30
|
|
#define SVC3_ROLE_SHIFT 4
|
|
|
|
#define SNS_GAN 0x100
|
|
#define SNS_GP3 0x171
|
|
#define SNS_RFT 0x217
|
|
typedef struct {
|
|
u_int16_t snscb_rblen; /* response buffer length (words) */
|
|
u_int16_t snscb_res0;
|
|
u_int16_t snscb_addr[4]; /* response buffer address */
|
|
u_int16_t snscb_sblen; /* subcommand buffer length (words) */
|
|
u_int16_t snscb_res1;
|
|
u_int16_t snscb_data[1]; /* variable data */
|
|
} sns_screq_t; /* Subcommand Request Structure */
|
|
#define SNS_GAN_REQ_SIZE (sizeof (sns_screq_t)+(5*(sizeof (u_int16_t))))
|
|
#define SNS_GP3_REQ_SIZE (sizeof (sns_screq_t)+(5*(sizeof (u_int16_t))))
|
|
#define SNS_RFT_REQ_SIZE (sizeof (sns_screq_t)+(21*(sizeof (u_int16_t))))
|
|
|
|
typedef struct {
|
|
u_int8_t snscb_cthdr[16];
|
|
u_int8_t snscb_port_type;
|
|
u_int8_t snscb_port_id[3];
|
|
u_int8_t snscb_portname[8];
|
|
u_int16_t snscb_data[1]; /* variable data */
|
|
} sns_scrsp_t; /* Subcommand Response Structure */
|
|
#define SNS_GAN_RESP_SIZE 608 /* Maximum response size (bytes) */
|
|
#define SNS_GP3_RESP_SIZE 532 /* XXX: For 128 ports */
|
|
#define SNS_RFT_RESP_SIZE 16
|
|
|
|
typedef struct {
|
|
u_int8_t snscb_cthdr[16];
|
|
u_int8_t snscb_port_type;
|
|
u_int8_t snscb_port_id[3];
|
|
u_int8_t snscb_portname[8];
|
|
u_int8_t snscb_pnlen; /* symbolic port name length */
|
|
u_int8_t snscb_pname[255]; /* symbolic port name */
|
|
u_int8_t snscb_nodename[8];
|
|
u_int8_t snscb_nnlen; /* symbolic node name length */
|
|
u_int8_t snscb_nname[255]; /* symbolic node name */
|
|
u_int8_t snscb_ipassoc[8];
|
|
u_int8_t snscb_ipaddr[16];
|
|
u_int8_t snscb_svc_class[4];
|
|
u_int8_t snscb_fc4_types[32];
|
|
u_int8_t snscb_fpname[8];
|
|
u_int8_t snscb_reserved;
|
|
u_int8_t snscb_hardaddr[3];
|
|
} sns_ganrsp_t; /* Subcommand Response Structure */
|
|
|
|
#endif /* _ISPMBOX_H */
|