freebsd-skq/usr.sbin/arp/arp.4
glebius bce78dfe17 Remove net.link.ether.inet.useloopback sysctl tunable. It was always on by
default from the very beginning. It was placed in wrong namespace
net.link.ether, originally it had been at another wrong namespace. It was
incorrectly documented at incorrect manual page arp(8). Since new-ARP commit,
the tunable have been consulted only on route addition, and ignored on route
deletion. Behaviour of a system with tunable turned off is not fully correct,
and has no advantages comparing to normal behavior.
2013-11-05 07:32:09 +00:00

236 lines
8.7 KiB
Groff

.\" Copyright (c) 1985, 1986, 1988, 1994
.\" The Regents of the University of California. All rights reserved.
.\"
.\" Redistribution and use in source and binary forms, with or without
.\" modification, are permitted provided that the following conditions
.\" are met:
.\" 1. Redistributions of source code must retain the above copyright
.\" notice, this list of conditions and the following disclaimer.
.\" 2. Redistributions in binary form must reproduce the above copyright
.\" notice, this list of conditions and the following disclaimer in the
.\" documentation and/or other materials provided with the distribution.
.\" 4. Neither the name of the University nor the names of its contributors
.\" may be used to endorse or promote products derived from this software
.\" without specific prior written permission.
.\"
.\" THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND
.\" ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
.\" IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
.\" ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE
.\" FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
.\" DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
.\" OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
.\" HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
.\" LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
.\" OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
.\" SUCH DAMAGE.
.\"
.\" @(#)arp4.4 6.5 (Berkeley) 4/18/94
.\" $FreeBSD$
.\"
.Dd November 5, 2013
.Dt ARP 4
.Os
.Sh NAME
.Nm arp
.Nd Address Resolution Protocol
.Sh SYNOPSIS
.Cd "device ether"
.Sh DESCRIPTION
The Address Resolution Protocol (ARP) is used to dynamically
map between Protocol Addresses (such as IP addresses) and
Local Network Addresses (such as Ethernet addresses).
This implementation maps IP addresses to Ethernet,
ARCnet,
or Token Ring addresses.
It is used by all the Ethernet interface drivers.
.Pp
ARP caches Internet-Ethernet address mappings.
When an interface requests a mapping for an address not in the cache,
ARP queues the message which requires the mapping and broadcasts
a message on the associated network requesting the address mapping.
If a response is provided, the new mapping is cached and any pending
message is transmitted.
ARP will queue at most one packet while waiting for a response to a
mapping request;
only the most recently ``transmitted'' packet is kept.
If the target host does not respond after several requests,
the host is considered to be down allowing an error to be returned to
transmission attempts.
Further demand for this mapping causes ARP request retransmissions, that
are ratelimited to one packet per second.
The error is
.Er EHOSTDOWN
for a non-responding destination host, and
.Er EHOSTUNREACH
for a non-responding router.
.Pp
The ARP cache is stored in the system routing table as
dynamically-created host routes.
The route to a directly-attached Ethernet network is installed as a
.Dq cloning
route (one with the
.Li RTF_CLONING
flag set),
causing routes to individual hosts on that network to be created on
demand.
These routes time out periodically (normally 20 minutes after validated;
entries are not validated when not in use).
.Pp
ARP entries may be added, deleted or changed with the
.Xr arp 8
utility.
Manually-added entries may be temporary or permanent,
and may be
.Dq published ,
in which case the system will respond to ARP requests for that host
as if it were the target of the request.
.Pp
In the past,
ARP was used to negotiate the use of a trailer encapsulation.
This is no longer supported.
.Pp
ARP watches passively for hosts impersonating the local host (i.e., a host
which responds to an ARP mapping request for the local host's address).
.Pp
Proxy ARP is a feature whereby the local host will respond to requests
for addresses other than itself, with its own address.
Normally, proxy ARP in
.Fx
is set up on a host-by-host basis using the
.Xr arp 8
utility, by adding an entry for each host inside a given subnet for
which proxying of ARP requests is desired.
However, the
.Dq "proxy all"
feature causes the local host to act as a proxy for
.Em all
hosts reachable through some other network interface,
different from the one the request came in from.
It may be enabled by setting the
.Xr sysctl 8
MIB variable
.Va net.link.ether.inet.proxyall
to 1.
.Sh MIB Variables
The ARP protocol implements a number of configurable variables in
.Va net.link.ether.inet
branch
of the
.Xr sysctl 3
MIB.
.Bl -tag -width "log_arp_permanent_modify"
.It Va allow_multicast
Should the kernel install ARP entries with multicast bit set in
the hardware address.
Installing such entries is RFC 1812 violation, but some prorietary
load balancing techniques require routers on network to do so.
Turned off by default.
.It Va log_arp_movements
Should the kernel log movements of IP addresses from one hardware
address to an other.
See
.Sx DIAGNOSTICS
below.
Turned on by default.
.It Va log_arp_permanent_modify
Should the kernel log attempts of remote host on network to modify a
permanent ARP entry.
See
.Sx DIAGNOSTICS
below.
Turned on by default.
.It Va log_arp_wrong_iface
Should the kernel log attempts to insert an ARP entry on an interface
when the IP network the address belongs to is connected to an other
interface.
See
.Sx DIAGNOSTICS
below.
Turned on by default.
.It Va max_log_per_second
Limit number of remotely triggered logging events to a configured value
per second.
Default is 1 log message per second.
.It Va max_age
How long an ARP entry is held in the cache until it needs to be refreshed.
Default is 1200 seconds.
.It Va maxhold
How many packets hold in the per-entry output queue while the entry
is being resolved.
Default is one packet.
.It Va maxtries
Number of retransmits before host is considered down and error is returned.
Default is 5 tries.
.It Va proxyall
Enables ARP proxying for all hosts on net.
Turned off by default.
.It Va wait
Lifetime of an incomplete ARP entry.
Default is 20 seconds.
.El
.Sh DIAGNOSTICS
.Bl -diag
.It "arp: %x:%x:%x:%x:%x:%x is using my IP address %d.%d.%d.%d on %s!"
ARP has discovered another host on the local network which responds to
mapping requests for its own Internet address with a different Ethernet
address, generally indicating that two hosts are attempting to use the
same Internet address.
.It "arp: link address is broadcast for IP address %d.%d.%d.%d!"
ARP requested information for a host, and received an answer indicating
that the host's ethernet address is the ethernet broadcast address.
This indicates a misconfigured or broken device.
.It "arp: %d.%d.%d.%d moved from %x:%x:%x:%x:%x:%x to %x:%x:%x:%x:%x:%x on %s"
ARP had a cached value for the ethernet address of the referenced host,
but received a reply indicating that the host is at a new address.
This can happen normally when host hardware addresses change,
or when a mobile node arrives or leaves the local subnet.
It can also indicate a problem with proxy ARP.
This message can only be issued if the sysctl
.Va net.link.ether.inet.log_arp_movements
is set to 1, which is the system's default behaviour.
.It "arpresolve: can't allocate llinfo for %d.%d.%d.%d"
The route for the referenced host points to a device upon which ARP is
required, but ARP was unable to allocate a routing table entry in which
to store the host's MAC address.
This usually points to a misconfigured routing table.
It can also occur if the kernel cannot allocate memory.
.It "arp: %d.%d.%d.%d is on if0 but got reply from %x:%x:%x:%x:%x:%x on if1"
Physical connections exist to the same logical IP network on both if0 and if1.
It can also occur if an entry already exists in the ARP cache for the IP
address above, and the cable has been disconnected from if0, then reconnected
to if1.
This message can only be issued if the sysctl
.Va net.link.ether.inet.log_arp_wrong_iface
is set to 1, which is the system's default behaviour.
.It "arp: %x:%x:%x:%x:%x:%x attempts to modify permanent entry for %d.%d.%d.%d on %s"
ARP has received an ARP reply that attempts to overwrite a permanent
entry in the local ARP table.
This error will only be logged if the sysctl
.Va net.link.ether.inet.log_arp_permanent_modify
is set to 1, which is the system's default behaviour.
.It "arp: %x:%x:%x:%x:%x:%x is multicast"
Kernel refused to install an entry with multicast hardware address.
If you really want such addresses being installed, set the sysctl
.Va net.link.ether.inet.allow_multicast
to a positive value.
.El
.Sh SEE ALSO
.Xr inet 4 ,
.Xr route 4 ,
.Xr arp 8 ,
.Xr ifconfig 8 ,
.Xr route 8 ,
.Xr sysctl 8
.Rs
.%A Plummer, D.
.%B "An Ethernet Address Resolution Protocol"
.%T RFC826
.Re
.Rs
.%A Leffler, S.J.
.%A Karels, M.J.
.%B "Trailer Encapsulations"
.%T RFC893
.Re