d/freebsd-skq
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
52751dc395
freebsd-skq/sys/i386/scsi/aic7xxx.c
gibbs d7924ba292 Clean up a few nits in the aic7xxx driver: 
1) Make the driver "quiet" by sticking most boot messages behind
	bootverbose conditionals.  This means that you won't see the
	sync and wide negotiation, but you will find out if they fail.

2) Add support to the 93cx6 serial eeprom code to read at an abitrary
	offset.  This is needed so that we can access the second half
	of the eeprom on 3940 cards where the second channel's config
	is stored.

3) Add flags argument to ahcprobe().  This is used by the pci probe code
	to tell the generic driver that an adapter should be treated
	as a channel B device as well as notify it of the presence of
	external SCB SRAM.  These are needed for some motherboard
	implementations of the aic7870 and for the 3940 controllers.

4) Print "Channel A"/"Channel B" instead of "Single Channel" for the
	two busses of the 3940.  I received many reports of confusion
	about how the 3940 was probed since most people belived that
	only one ahc entry was needed.  This will hopefully make it
	clearer.

5) Walk the SCBs to determine just how many their are if external SCB
	ram is detected.

6) Hard code that external SCB ram is present for the 3940 since it doesn't
	use the documented reporting facility for reporting the SRAM. :(
	255 commands per channel are supported on the 3940.

7) Read the seeprom starting at addres 32 for the second channel of the
	3940 so we get the right info for that channel.

8) Clean up printing of the "Disabling tagged queuing message".

9) Queue timeouts if they occur while we are handling a timeout.  The code
	was totally unprotected in this scenario.
Reviewed by: Timeout code reviewed by David Greenman <davidg>
1995-09-05 23:52:03 +00:00

3082 lines
82 KiB
C
Raw Blame History

/*
* Generic driver for the aic7xxx based adaptec SCSI controllers
* Copyright (c) 1994, 1995 Justin T. Gibbs.
* All rights reserved.
*
* Product specific probe and attach routines can be found in:
* i386/isa/aic7770.c 27/284X and aic7770 motherboard controllers
* /pci/aic7870.c 3940, 2940, aic7870 and aic7850 controllers
*
* Portions of this driver are based on the FreeBSD 1742 Driver:
*
* Written by Julian Elischer (julian@tfs.com)
* for TRW Financial Systems for use under the MACH(2.5) operating system.
*
* TRW Financial Systems, in accordance with their agreement with Carnegie
* Mellon University, makes this software available to CMU to distribute
* or use in any manner that they see fit as long as this message is kept with
* the software. For this reason TFS also grants any other persons or
* organisations permission to use or modify this software.
*
* TFS supplies this software to be publicly redistributed
* on the understanding that TFS is not responsible for the correct
* functioning of this software in any circumstances.
*
* commenced: Sun Sep 27 18:14:01 PDT 1992
*
* $Id: aic7xxx.c,v 1.37 1995/08/23 23:03:17 gibbs Exp $
*/
/*
* TODO:
* Implement Target Mode
*
*/
#include <sys/param.h>
#include <sys/systm.h>
#include <sys/malloc.h>
#include <sys/buf.h>
#include <sys/proc.h>
#include <sys/user.h>
#include <scsi/scsi_all.h>
#include <scsi/scsiconf.h>
#include <machine/clock.h>
#include <i386/scsi/aic7xxx.h>
#include <i386/scsi/93cx6.h>
#define PAGESIZ 4096
#define MAX_TAGS 4;
#include <sys/kernel.h>
#define KVTOPHYS(x) vtophys(x)
#define MIN(a,b) ((a < b) ? a : b)
#define ALL_TARGETS -1
struct ahc_data *ahcdata[NAHC];
int ahc_init __P((int unit));
void ahc_loadseq __P((u_long iobase));
int32 ahc_scsi_cmd();
timeout_t ahc_timeout;
void ahc_done __P((int unit, struct scb *scbp));
void ahc_timeout_done __P((int unit, struct scb *scbp));
struct scb *ahc_get_scb __P((int unit, int flags));
void ahc_free_scb();
void ahc_scb_timeout __P((int unit, struct ahc_data *ahc, struct scb *scb));
u_char ahc_abort_wscb __P((int unit, struct scb *scbp, u_char prev,
u_long iobase, u_char timedout_scb, u_int32 xs_error));
int ahc_match_scb __P((struct scb *scb, int target, char channel));
int ahc_reset_device __P((int unit, struct ahc_data *ahc, int target,
char channel, u_char timedout_scb, u_int32 xs_error));
void ahc_reset_current_bus __P((u_long iobase));
int ahc_reset_channel __P((int unit, struct ahc_data *ahc, char channel,
u_char timedout_scb, u_int32 xs_error));
void ahcminphys();
void ahc_unbusy_target __P((int target, char channel, u_long iobase));
struct scb *ahc_scb_phys_kv();
int ahc_poll __P((int unit, int wait));
u_int32 ahc_adapter_info();
int ahc_unit = 0;
/* Different debugging levels */
#define AHC_SHOWMISC 0x0001
#define AHC_SHOWCMDS 0x0002
#define AHC_SHOWSCBS 0x0004
#define AHC_SHOWABORTS 0x0008
#define AHC_SHOWSENSE 0x0010
#define AHC_DEBUG
int ahc_debug = AHC_SHOWABORTS;
/**** bit definitions for SCSIDEF ****/
#define HSCSIID 0x07 /* our SCSI ID */
#define HWSCSIID 0x0f /* our SCSI ID if Wide Bus */
typedef enum {
list_head,
list_second,
list_tail
}insert_t;
struct scsi_adapter ahc_switch =
{
ahc_scsi_cmd,
ahcminphys,
0,
0,
ahc_adapter_info,
"ahc",
{ 0, 0 }
};
/* the below structure is so we have a default dev struct for our link struct */
struct scsi_device ahc_dev =
{
NULL, /* Use default error handler */
NULL, /* have a queue, served by this */
NULL, /* have no async handler */
NULL, /* Use default 'done' routine */
"ahc",
0,
{ 0, 0 }
};
/*
* All of these should be in a separate header file shared by the sequencer
* code and the kernel level driver. The only catch is that we would need to
* add an additional 0xc00 offset when using them in the kernel driver. The
* aic7770 assembler must be modified to allow include files as well. All
* page numbers refer to the Adaptec AIC-7770 Data Book availible from
* Adaptec's Technical Documents Department 1-800-934-2766
*/
/* -------------------- AIC-7770 offset definitions ----------------------- */
/*
* SCSI Sequence Control (p. 3-11).
* Each bit, when set starts a specific SCSI sequence on the bus
*/
#define SCSISEQ 0xc00ul
#define TEMODEO 0x80
#define ENSELO 0x40
#define ENSELI 0x20
#define ENRSELI 0x10
#define ENAUTOATNO 0x08
#define ENAUTOATNI 0x04
#define ENAUTOATNP 0x02
#define SCSIRSTO 0x01
/*
* SCSI Transfer Control 1 Register (pp. 3-14,15).
* Controls the SCSI module data path.
*/
#define SXFRCTL1 0xc02ul
#define BITBUCKET 0x80
#define SWRAPEN 0x40
#define ENSPCHK 0x20
#define STIMESEL 0x18
#define ENSTIMER 0x04
#define ACTNEGEN 0x02
#define STPWEN 0x01 /* Powered Termination */
/*
* SCSI Interrrupt Mode 1 (pp. 3-28,29).
* Set bits in this register enable the corresponding
* interrupt source.
*/
#define SIMODE1 0xc11ul
#define ENSELTIMO 0x80
#define ENATNTARG 0x40
#define ENSCSIRST 0x20
#define ENPHASEMIS 0x10
#define ENBUSFREE 0x08
#define ENSCSIPERR 0x04
#define ENPHASECHG 0x02
#define ENREQINIT 0x01
/*
* SCSI Control Signal Read Register (p. 3-15).
* Reads the actual state of the SCSI bus pins
*/
#define SCSISIGI 0xc03ul
#define CDI 0x80
#define IOI 0x40
#define MSGI 0x20
#define ATNI 0x10
#define SELI 0x08
#define BSYI 0x04
#define REQI 0x02
#define ACKI 0x01
/*
* SCSI Contol Signal Write Register (p. 3-16).
* Writing to this register modifies the control signals on the bus. Only
* those signals that are allowed in the current mode (Initiator/Target) are
* asserted.
*/
#define SCSISIGO 0xc03ul
#define CDO 0x80
#define IOO 0x40
#define MSGO 0x20
#define ATNO 0x10
#define SELO 0x08
#define BSYO 0x04
#define REQO 0x02
#define ACKO 0x01
/*
* SCSI Rate Control (p. 3-17).
* Contents of this register determine the Synchronous SCSI data transfer
* rate and the maximum synchronous Req/Ack offset. An offset of 0 in the
* SOFS (3:0) bits disables synchronous data transfers. Any offset value
* greater than 0 enables synchronous transfers.
*/
#define SCSIRATE 0xc04ul
#define WIDEXFER 0x80 /* Wide transfer control */
#define SXFR 0x70 /* Sync transfer rate */
#define SOFS 0x0f /* Sync offset */
/*
* SCSI ID (p. 3-18).
* Contains the ID of the board and the current target on the
* selected channel
*/
#define SCSIID 0xc05ul
#define TID 0xf0 /* Target ID mask */
#define OID 0x0f /* Our ID mask */
/*
* SCSI Transfer Count (pp. 3-19,20)
* These registers count down the number of bytes transfered
* across the SCSI bus. The counter is decremented only once
* the data has been safely transfered. SDONE in SSTAT0 is
* set when STCNT goes to 0
*/
#define STCNT 0xc08ul
/*
* SCSI Status 0 (p. 3-21)
* Contains one set of SCSI Interrupt codes
* These are most likely of interest to the sequencer
*/
#define SSTAT0 0xc0bul
#define TARGET 0x80 /* Board is a target */
#define SELDO 0x40 /* Selection Done */
#define SELDI 0x20 /* Board has been selected */
#define SELINGO 0x10 /* Selection In Progress */
#define SWRAP 0x08 /* 24bit counter wrap */
#define SDONE 0x04 /* STCNT = 0x000000 */
#define SPIORDY 0x02 /* SCSI PIO Ready */
#define DMADONE 0x01 /* DMA transfer completed */
/*
* Clear SCSI Interrupt 1 (p. 3-23)
* Writing a 1 to a bit clears the associated SCSI Interrupt in SSTAT1.
*/
#define CLRSINT1 0xc0cul
#define CLRSELTIMEO 0x80
#define CLRATNO 0x40
#define CLRSCSIRSTI 0x20
/* UNUSED 0x10 */
#define CLRBUSFREE 0x08
#define CLRSCSIPERR 0x04
#define CLRPHASECHG 0x02
#define CLRREQINIT 0x01
/*
* SCSI Status 1 (p. 3-24)
* These interrupt bits are of interest to the kernel driver
*/
#define SSTAT1 0xc0cul
#define SELTO 0x80
#define ATNTARG 0x40
#define SCSIRSTI 0x20
#define PHASEMIS 0x10
#define BUSFREE 0x08
#define SCSIPERR 0x04
#define PHASECHG 0x02
#define REQINIT 0x01
/*
* SCSI/Host Address (p. 3-30)
* These registers hold the host address for the byte about to be
* transfered on the SCSI bus. They are counted up in the same
* manner as STCNT is counted down. SHADDR should always be used
* to determine the address of the last byte transfered since HADDR
* can be squewed by write ahead.
*/
#define SHADDR 0xc14ul
/*
* Selection/Reselection ID (p. 3-31)
* Upper four bits are the device id. The ONEBIT is set when the re/selecting
* device did not set its own ID.
*/
#define SELID 0xc19ul
#define SELID_MASK 0xf0
#define ONEBIT 0x08
/* UNUSED 0x07 */
/*
* SCSI Block Control (p. 3-32)
* Controls Bus type and channel selection. In a twin channel configuration
* addresses 0x00-0x1e are gated to the appropriate channel based on this
* register. SELWIDE allows for the coexistence of 8bit and 16bit devices
* on a wide bus.
*/
#define SBLKCTL 0xc1ful
/* UNUSED 0xc0 */
#define AUTOFLUSHDIS 0x20
/* UNUSED 0x10 */
#define SELBUSB 0x08
/* UNUSED 0x04 */
#define SELWIDE 0x02
/* UNUSED 0x01 */
/*
* Sequencer Control (p. 3-33)
* Error detection mode and speed configuration
*/
#define SEQCTL 0xc60ul
#define PERRORDIS 0x80
#define PAUSEDIS 0x40
#define FAILDIS 0x20
#define FASTMODE 0x10
#define BRKADRINTEN 0x08
#define STEP 0x04
#define SEQRESET 0x02
#define LOADRAM 0x01
/*
* Sequencer RAM Data (p. 3-34)
* Single byte window into the Scratch Ram area starting at the address
* specified by SEQADDR0 and SEQADDR1. To write a full word, simply write
* four bytes in sucessesion. The SEQADDRs will increment after the most
* significant byte is written
*/
#define SEQRAM 0xc61ul
/*
* Sequencer Address Registers (p. 3-35)
* Only the first bit of SEQADDR1 holds addressing information
*/
#define SEQADDR0 0xc62ul
#define SEQADDR1 0xc63ul
#define SEQADDR1_MASK 0x01
/*
* Accumulator
* We cheat by passing arguments in the Accumulator up to the kernel driver
*/
#define ACCUM 0xc64ul
#define SINDEX 0xc65ul
/*
* Board Control (p. 3-43)
*/
#define BCTL 0xc84ul
/* RSVD 0xf0 */
#define ACE 0x08 /* Support for external processors */
/* RSVD 0x06 */
#define ENABLE 0x01
/*
* Bus On/Off Time (p. 3-44)
*/
#define BUSTIME 0xc85ul
#define BOFF 0xf0
#define BON 0x0f
/*
* Bus Speed (p. 3-45)
*/
#define BUSSPD 0xc86ul
#define DFTHRSH 0xc0
#define STBOFF 0x38
#define STBON 0x07
/*
* Host Control (p. 3-47) R/W
* Overal host control of the device.
*/
#define HCNTRL 0xc87ul
/* UNUSED 0x80 */
#define POWRDN 0x40
/* UNUSED 0x20 */
#define SWINT 0x10
#define IRQMS 0x08
#define PAUSE 0x04
#define INTEN 0x02
#define CHIPRST 0x01
/*
* Host Address (p. 3-48)
* This register contains the address of the byte about
* to be transfered across the host bus.
*/
#define HADDR 0xc88ul
/*
* SCB Pointer (p. 3-49)
* Gate one of the four SCBs into the SCBARRAY window.
*/
#define SCBPTR 0xc90ul
/*
* Interrupt Status (p. 3-50)
* Status for system interrupts
*/
#define INTSTAT 0xc91ul
#define SEQINT_MASK 0xf0 /* SEQINT Status Codes */
#define BAD_PHASE 0x00
#define SEND_REJECT 0x10
#define NO_IDENT 0x20
#define NO_MATCH 0x30
#define MSG_SDTR 0x40
#define MSG_WDTR 0x50
#define MSG_REJECT 0x60
#define BAD_STATUS 0x70
#define RESIDUAL 0x80
#define ABORT_TAG 0x90
#define AWAITING_MSG 0xa0
#define IMMEDDONE 0xb0
#define BRKADRINT 0x08
#define SCSIINT 0x04
#define CMDCMPLT 0x02
#define SEQINT 0x01
#define INT_PEND (BRKADRINT | SEQINT | SCSIINT | CMDCMPLT)
/*
* Hard Error (p. 3-53)
* Reporting of catastrophic errors. You usually cannot recover from
* these without a full board reset.
*/
#define ERROR 0xc92ul
/* UNUSED 0xf0 */
#define PARERR 0x08
#define ILLOPCODE 0x04
#define ILLSADDR 0x02
#define ILLHADDR 0x01
/*
* Clear Interrupt Status (p. 3-52)
*/
#define CLRINT 0xc92ul
#define CLRBRKADRINT 0x08
#define CLRSCSIINT 0x04
#define CLRCMDINT 0x02
#define CLRSEQINT 0x01
/*
* SCB Auto Increment (p. 3-59)
* Byte offset into the SCB Array and an optional bit to allow auto
* incrementing of the address during download and upload operations
*/
#define SCBCNT 0xc9aul
#define SCBAUTO 0x80
#define SCBCNT_MASK 0x1f
/*
* Queue In FIFO (p. 3-60)
* Input queue for queued SCBs (commands that the seqencer has yet to start)
*/
#define QINFIFO 0xc9bul
/*
* Queue In Count (p. 3-60)
* Number of queued SCBs
*/
#define QINCNT 0xc9cul
/*
* Queue Out FIFO (p. 3-61)
* Queue of SCBs that have completed and await the host
*/
#define QOUTFIFO 0xc9dul
/*
* Queue Out Count (p. 3-61)
* Number of queued SCBs in the Out FIFO
*/
#define QOUTCNT 0xc9eul
#define SCBARRAY 0xca0ul
/* ---------------- END AIC-7770 Register Definitions ----------------- */
/* --------------------- AIC-7870-only definitions -------------------- */
#define DSPCISTATUS 0xc86ul
/*
* Serial EEPROM Control (p. 4-92 in 7870 Databook)
* Controls the reading and writing of an external serial 1-bit
* EEPROM Device. In order to access the serial EEPROM, you must
* first set the SEEMS bit that generates a request to the memory
* port for access to the serial EEPROM device. When the memory
* port is not busy servicing another request, it reconfigures
* to allow access to the serial EEPROM. When this happens, SEERDY
* gets set high to verify that the memory port access has been
* granted.
*
* After successful arbitration for the memory port, the SEECS bit of
* the SEECTL register is connected to the chip select. The SEECK,
* SEEDO, and SEEDI are connected to the clock, data out, and data in
* lines respectively. The SEERDY bit of SEECTL is useful in that it
* gives us an 800 nsec timer. After a write to the SEECTL register,
* the SEERDY goes high 800 nsec later. The one exception to this is
* when we first request access to the memory port. The SEERDY goes
* high to signify that access has been granted and, for this case, has
* no implied timing.
*
* See 93cx6.c for detailed information on the protocol necessary to
* read the serial EEPROM.
*/
#define SEECTL 0xc1eul
#define EXTARBACK 0x80
#define EXTARBREQ 0x40
#define SEEMS 0x20
#define SEERDY 0x10
#define SEECS 0x08
#define SEECK 0x04
#define SEEDO 0x02
#define SEEDI 0x01
/* ---------------------- Scratch RAM Offsets ------------------------- */
/* These offsets are either to values that are initialized by the board's
* BIOS or are specified by the Linux sequencer code. If I can figure out
* how to read the EISA configuration info at probe time, the cards could
* be run without BIOS support installed
*/
/*
* 1 byte per target starting at this address for configuration values
*/
#define HA_TARG_SCRATCH 0xc20ul
/*
* The sequencer will stick the frist byte of any rejected message here so
* we can see what is getting thrown away.
*/
#define HA_REJBYTE 0xc31ul
/*
* Bit vector of targets that have disconnection disabled.
*/
#define HA_DISC_DSB 0xc32ul
/*
* Length of pending message
*/
#define HA_MSG_LEN 0xc34ul
/*
* message body
*/
#define HA_MSG_START 0xc35ul /* outgoing message body */
/*
* These are offsets into the card's scratch ram. Some of the values are
* specified in the AHA2742 technical reference manual and are initialized
* by the BIOS at boot time.
*/
#define HA_ARG_1 0xc4aul
#define HA_RETURN_1 0xc4aul
#define SEND_SENSE 0x80
#define SEND_WDTR 0x80
#define SEND_SDTR 0x80
#define SEND_REJ 0x40
#define SG_COUNT 0xc4dul
#define SG_NEXT 0xc4eul
#define HA_SIGSTATE 0xc4bul
#define HA_SCBCOUNT 0xc52ul
#define HA_FLAGS 0xc53ul
#define SINGLE_BUS 0x00
#define TWIN_BUS 0x01
#define WIDE_BUS 0x02
#define ACTIVE_MSG 0x20
#define IDENTIFY_SEEN 0x40
#define RESELECTING 0x80
#define HA_ACTIVE0 0xc54ul
#define HA_ACTIVE1 0xc55ul
#define SAVED_TCL 0xc56ul
#define WAITING_SCBH 0xc57ul
#define WAITING_SCBT 0xc58ul
#define HA_SCSICONF 0xc5aul
#define INTDEF 0xc5cul
#define HA_HOSTCONF 0xc5dul
#define HA_274_BIOSCTRL 0xc5ful
#define BIOSMODE 0x30
#define BIOSDISABLED 0x30
#define MSG_ABORT 0x06
#define MSG_BUS_DEVICE_RESET 0x0c
#define BUS_8_BIT 0x00
#define BUS_16_BIT 0x01
#define BUS_32_BIT 0x02
/*
* Define the format of the SEEPROM registers (16 bits).
*
*/
struct seeprom_config {
/*
* SCSI ID Configuration Flags
*/
#define CFXFER 0x0007 /* synchronous transfer rate */
#define CFSYNCH 0x0008 /* enable synchronous transfer */
#define CFDISC 0x0010 /* enable disconnection */
#define CFWIDEB 0x0020 /* wide bus device */
/* UNUSED 0x00C0 */
#define CFSTART 0x0100 /* send start unit SCSI command */
#define CFINCBIOS 0x0200 /* include in BIOS scan */
#define CFRNFOUND 0x0400 /* report even if not found */
/* UNUSED 0xf800 */
unsigned short device_flags[16]; /* words 0-15 */
/*
* BIOS Control Bits
*/
#define CFSUPREM 0x0001 /* support all removeable drives */
#define CFSUPREMB 0x0002 /* support removeable drives for boot only */
#define CFBIOSEN 0x0004 /* BIOS enabled */
/* UNUSED 0x0008 */
#define CFSM2DRV 0x0010 /* support more than two drives */
/* UNUSED 0x0060 */
#define CFEXTEND 0x0080 /* extended translation enabled */
/* UNUSED 0xff00 */
unsigned short bios_control; /* word 16 */
/*
* Host Adapter Control Bits
*/
/* UNUSED 0x0003 */
#define CFSTERM 0x0004 /* SCSI low byte termination (non-wide cards) */
#define CFWSTERM 0x0008 /* SCSI high byte termination (wide card) */
#define CFSPARITY 0x0010 /* SCSI parity */
/* UNUSED 0x0020 */
#define CFRESETB 0x0040 /* reset SCSI bus at IC initialization */
/* UNUSED 0xff80 */
unsigned short adapter_control; /* word 17 */
/*
* Bus Release, Host Adapter ID
*/
#define CFSCSIID 0x000f /* host adapter SCSI ID */
/* UNUSED 0x00f0 */
#define CFBRTIME 0xff00 /* bus release time */
unsigned short brtime_id; /* word 18 */
/*
* Maximum targets
*/
#define CFMAXTARG 0x00ff /* maximum targets */
/* UNUSED 0xff00 */
unsigned short max_targets; /* word 19 */
unsigned short res_1[11]; /* words 20-30 */
unsigned short checksum; /* word 31 */
};
/*
* Since the sequencer can disable pausing in a critical section, we
* must loop until it actually stops.
* XXX Should add a timeout in here??
*/
#define PAUSE_SEQUENCER(ahc) \
outb(HCNTRL + ahc->baseport, ahc->pause); \
\
while ((inb(HCNTRL + ahc->baseport) & PAUSE) == 0) \
;
#define UNPAUSE_SEQUENCER(ahc) \
outb( HCNTRL + ahc->baseport, ahc->unpause )
/*
* Restart the sequencer program from address zero
*/
#define RESTART_SEQUENCER(ahc) \
do { \
outb( SEQCTL + ahc->baseport, SEQRESET|FASTMODE ); \
} while (inb(SEQADDR0 + ahc->baseport) != 0 && \
inb(SEQADDR1 + ahc->baseport != 0)); \
\
UNPAUSE_SEQUENCER(ahc);
#ifdef AHC_DEBUG
void
ahc_print_scb(scb)
struct scb *scb;
{
printf("scb:0x%x control:0x%x tcl:0x%x cmdlen:%d cmdpointer:0x%x\n"
,scb
,scb->control
,scb->target_channel_lun
,scb->cmdlen
,scb->cmdpointer );
printf(" datlen:%d data:0x%x res:0x%x segs:0x%x segp:0x%x\n"
,scb->datalen[2] << 16 | scb->datalen[1] << 8 | scb->datalen[0]
,scb->data
,scb->RESERVED[1] << 8 | scb->RESERVED[0]
,scb->SG_segment_count
,scb->SG_list_pointer);
printf(" sg_addr:%x sg_len:%d\n"
,scb->ahc_dma[0].addr
,scb->ahc_dma[0].len);
printf(" size:%d\n"
,(int)&(scb->next) - (int)scb);
}
void
ahc_print_active_scb(ahc)
struct ahc_data *ahc;
{
int cur_scb_offset;
u_long iobase = ahc->baseport;
PAUSE_SEQUENCER(ahc);
cur_scb_offset = inb(SCBPTR + iobase);
UNPAUSE_SEQUENCER(ahc);
ahc_print_scb(ahc->scbarray[cur_scb_offset]);
}
#endif
#define PARERR 0x08
#define ILLOPCODE 0x04
#define ILLSADDR 0x02
#define ILLHADDR 0x01
static struct {
u_char errno;
char *errmesg;
} hard_error[] = {
{ ILLHADDR, "Illegal Host Access" },
{ ILLSADDR, "Illegal Sequencer Address referrenced" },
{ ILLOPCODE, "Illegal Opcode in sequencer program" },
{ PARERR, "Sequencer Ram Parity Error" }
};
/*
* Valid SCSIRATE values. (p. 3-17)
* Provides a mapping of tranfer periods in ns to the proper value to
* stick in the scsiscfr reg to use that transfer rate.
*/
static struct {
short sxfr;
short period; /* in ns */
char *rate;
} ahc_syncrates[] = {
{ 0x00, 100, "10.0" },
{ 0x10, 125, "8.0" },
{ 0x20, 150, "6.67" },
{ 0x30, 175, "5.7" },
{ 0x40, 200, "5.0" },
{ 0x50, 225, "4.4" },
{ 0x60, 250, "4.0" },
{ 0x70, 275, "3.6" }
};
static int ahc_num_syncrates =
sizeof(ahc_syncrates) / sizeof(ahc_syncrates[0]);
/*
* Check if the device can be found at the port given
* and if so, determine configuration and set it up for further work.
*/
int
ahcprobe(unit, iobase, type, flags)
int unit;
u_long iobase;
ahc_type type;
ahc_flag flags;
{
/*
* find unit and check we have that many defined
*/
struct ahc_data *ahc;
if (unit >= NAHC) {
printf("ahc: unit number (%d) too high\n", unit);
return 0;
}
/*
* Allocate a storage area for us
*/
if (ahcdata[unit]) {
printf("ahc%d: memory already allocated\n", unit);
return 0;
}
ahc = malloc(sizeof(struct ahc_data), M_TEMP, M_NOWAIT);
if (!ahc) {
printf("ahc%d: cannot malloc!\n", unit);
return 0;
}
bzero(ahc, sizeof(struct ahc_data));
ahcdata[unit] = ahc;
ahc->baseport = iobase;
ahc->type = type;
ahc->flags = flags;
/*
* Try to initialize a unit at this location
* reset the AIC-7770, read its registers,
* and fill in the dev structure accordingly
*/
if (ahc_init(unit) != 0) {
ahcdata[unit] = NULL;
free(ahc, M_TEMP);
return (0);
}
return (1);
}
/*
* Look up the valid period to SCSIRATE conversion in our table.
*/
static
void ahc_scsirate(scsirate, period, offset, unit, target )
u_char *scsirate;
u_char period, offset;
int unit, target;
{
int i;
for (i = 0; i < ahc_num_syncrates; i++) {
if ((ahc_syncrates[i].period - period) >= 0) {
*scsirate = (ahc_syncrates[i].sxfr) | (offset & 0x0f);
if(bootverbose) {
printf("ahc%d: target %d synchronous at %sMB/s,"
" offset = 0x%x\n", unit, target,
ahc_syncrates[i].rate, offset );
}
return;
}
}
/* Default to asyncronous transfers. Also reject this SDTR request. */
*scsirate = 0;
if(bootverbose) {
printf("ahc%d: target %d using asyncronous transfers\n",
unit, target );
}
}
/*
* Attach all the sub-devices we can find
*/
int
ahc_attach(unit)
int unit;
{
struct ahc_data *ahc = ahcdata[unit];
struct scsibus_data *scbus;
/*
* fill in the prototype scsi_link.
*/
ahc->sc_link.adapter_unit = unit;
ahc->sc_link.adapter_targ = ahc->our_id;
ahc->sc_link.adapter = &ahc_switch;
ahc->sc_link.opennings = 2;
ahc->sc_link.device = &ahc_dev;
ahc->sc_link.flags = DEBUGLEVEL;
ahc->sc_link.fordriver = 0;
/*
* Prepare the scsibus_data area for the upperlevel
* scsi code.
*/
scbus = scsi_alloc_bus();
if(!scbus)
return 0;
scbus->adapter_link = &ahc->sc_link;
if(ahc->type & AHC_WIDE)
scbus->maxtarg = 15;
/*
* ask the adapter what subunits are present
*/
if(bootverbose)
printf("ahc%d: Probing channel A\n", unit);
scsi_attachdevs(scbus);
scbus = NULL; /* Upper-level SCSI code owns this now */
if(ahc->type & AHC_TWIN) {
/* Configure the second scsi bus */
ahc->sc_link_b = ahc->sc_link;
ahc->sc_link_b.adapter_targ = ahc->our_id_b;
ahc->sc_link_b.adapter_bus = 1;
ahc->sc_link_b.fordriver = (void *)SELBUSB;
scbus = scsi_alloc_bus();
if(!scbus)
return 0;
scbus->adapter_link = &ahc->sc_link_b;
if(ahc->type & AHC_WIDE)
scbus->maxtarg = 15;
if(bootverbose)
printf("ahc%d: Probing Channel B\n", unit);
scsi_attachdevs(scbus);
scbus = NULL; /* Upper-level SCSI code owns this now */
}
return 1;
}
void
ahc_send_scb( ahc, scb )
struct ahc_data *ahc;
struct scb *scb;
{
u_long iobase = ahc->baseport;
PAUSE_SEQUENCER(ahc);
outb(QINFIFO + iobase, scb->position);
UNPAUSE_SEQUENCER(ahc);
}
static
void ahc_getscb(iobase, scb)
u_long iobase;
struct scb *scb;
{
outb(SCBCNT + iobase, 0x80); /* SCBAUTO */
insb(SCBARRAY + iobase, scb, SCB_UP_SIZE);
outb(SCBCNT + iobase, 0);
}
/*
* Add this SCB to the "waiting for selection" list.
*/
static
void ahc_add_waiting_scb (iobase, scb, where)
u_long iobase;
struct scb *scb;
insert_t where;
{
u_char head, tail;
u_char curscb;
curscb = inb(SCBPTR + iobase);
head = inb(WAITING_SCBH + iobase);
tail = inb(WAITING_SCBT + iobase);
if(head == SCB_LIST_NULL) {
/* List was empty */
head = scb->position;
tail = SCB_LIST_NULL;
}
else if (where == list_head) {
outb(SCBPTR+iobase, scb->position);
outb(SCBARRAY+iobase+30, head);
head = scb->position;
}
else if(tail == SCB_LIST_NULL) {
/* List had one element */
tail = scb->position;
outb(SCBPTR+iobase,head);
outb(SCBARRAY+iobase+30,
tail);
}
else if(where == list_second) {
u_char third_scb;
outb(SCBPTR+iobase, head);
third_scb = inb(SCBARRAY+iobase+30);
outb(SCBARRAY+iobase+30,scb->position);
outb(SCBPTR+iobase, scb->position);
outb(SCBARRAY+iobase+30,third_scb);
}
else {
outb(SCBPTR+iobase,tail);
tail = scb->position;
outb(SCBARRAY+iobase+30,
tail);
}
outb(WAITING_SCBH + iobase, head);
outb(WAITING_SCBT + iobase, tail);
outb(SCBPTR + iobase, curscb);
}
/*
* Catch an interrupt from the adaptor
*/
int
ahcintr(unit)
int unit;
{
int intstat;
u_char status;
struct ahc_data *ahc = ahcdata[unit];
u_long iobase = ahc->baseport;
struct scb *scb = NULL;
struct scsi_xfer *xs = NULL;
intstat = inb(INTSTAT + iobase);
/*
* Is this interrupt for me? or for
* someone who is sharing my interrupt
*/
if (!(intstat & INT_PEND))
return 0;
if (intstat & BRKADRINT) {
/* We upset the sequencer :-( */
/* Lookup the error message */
int i, error = inb(ERROR + iobase);
int num_errors = sizeof(hard_error)/sizeof(hard_error[0]);
for(i = 0; error != 1 && i < num_errors; i++)
error >>= 1;
panic("ahc%d: brkadrint, %s at seqaddr = 0x%x\n",
unit, hard_error[i].errmesg,
(inb(SEQADDR1 + iobase) << 8) |
inb(SEQADDR0 + iobase));
}
if (intstat & SEQINT) {
u_short targ_mask;
u_char target = (inb(SCSIID + iobase) >> 4) & 0x0f;
u_char scratch_offset = target;
char channel =
inb(SBLKCTL + iobase) & SELBUSB ? 'B': 'A';
if (channel == 'B')
scratch_offset += 8;
targ_mask = (0x01 << scratch_offset);
switch (intstat & SEQINT_MASK) {
case BAD_PHASE:
panic("ahc%d:%c:%d: unknown scsi bus phase. "
"Attempting to continue\n",
unit, channel, target);
break;
case SEND_REJECT:
{
u_char rejbyte = inb(HA_REJBYTE + iobase);
if(( rejbyte & 0xf0) == 0x20) {
/* Tagged Message */
printf("\nahc%d:%c:%d: Tagged message "
"rejected. Disabling tagged "
"commands for this target.\n",
unit, channel, target);
ahc->tagenable &= ~targ_mask;
}
else
printf("ahc%d:%c:%d: Warning - message "
"rejected by target: 0x%x\n",
unit, channel, target, rejbyte);
break;
}
case NO_IDENT:
panic("ahc%d:%c:%d: Target did not send an IDENTIFY "
"message. SAVED_TCL == 0x%x\n",
unit, channel, target,
inb(SAVED_TCL + iobase));
break;
case NO_MATCH:
{
printf("ahc%d:%c:%d: no active SCB for "
"reconnecting target - "
"issuing ABORT\n", unit, channel,
target);
printf("SAVED_TCL == 0x%x\n",
inb(SAVED_TCL + iobase));
ahc_unbusy_target(target, channel, iobase);
outb(SCBARRAY + iobase, SCB_NEEDDMA);
outb(CLRSINT1 + iobase, CLRSELTIMEO);
RESTART_SEQUENCER(ahc);
break;
}
case MSG_SDTR:
{
u_char period, offset, rate;
u_char targ_scratch;
u_char maxoffset;
/*
* Help the sequencer to translate the
* negotiated transfer rate. Transfer is
* 1/4 the period in ns as is returned by
* the sync negotiation message. So, we must
* multiply by four
*/
period = inb(HA_ARG_1 + iobase) << 2;
offset = inb(ACCUM + iobase);
targ_scratch = inb(HA_TARG_SCRATCH + iobase
+ scratch_offset);
if(targ_scratch & WIDEXFER)
maxoffset = 0x08;
else
maxoffset = 0x0f;
ahc_scsirate(&rate, period,
MIN(offset,maxoffset), unit, target);
/* Preserve the WideXfer flag */
targ_scratch = rate | (targ_scratch & WIDEXFER);
outb(HA_TARG_SCRATCH + iobase + scratch_offset,
targ_scratch);
outb(SCSIRATE + iobase, targ_scratch);
if( (targ_scratch & 0x0f) == 0 )
{
/*
* The requested rate was so low
* that asyncronous transfers are
* faster (not to mention the
* controller won't support them),
* so we issue a message reject to
* ensure we go to asyncronous
* transfers.
*/
outb(HA_RETURN_1 + iobase, SEND_REJ);
}
/* See if we initiated Sync Negotiation */
else if(ahc->sdtrpending & targ_mask)
{
/*
* Don't send an SDTR back to
* the target
*/
outb(HA_RETURN_1 + iobase, 0);
}
else{
/*
* Send our own SDTR in reply
*/
#ifdef AHC_DEBUG
if(ahc_debug & AHC_SHOWMISC)
printf("Sending SDTR!!\n");
#endif
outb(HA_RETURN_1 + iobase, SEND_SDTR);
}
/*
* Negate the flags
*/
ahc->needsdtr &= ~targ_mask;
ahc->sdtrpending &= ~targ_mask;
break;
}
case MSG_WDTR:
{
u_char scratch, bus_width;
bus_width = inb(ACCUM + iobase);
scratch = inb(HA_TARG_SCRATCH + iobase
+ scratch_offset);
if(ahc->wdtrpending & targ_mask)
{
/*
* Don't send a WDTR back to the
* target, since we asked first.
*/
outb(HA_RETURN_1 + iobase, 0);
switch(bus_width)
{
case BUS_8_BIT:
scratch &= 0x7f;
break;
case BUS_16_BIT:
if(bootverbose)
printf("ahc%d: target "
"%d using 16Bit "
"transfers\n",
unit, target);
scratch |= 0x80;
break;
default:
break;
}
}
else {
/*
* Send our own WDTR in reply
*/
switch(bus_width)
{
case BUS_8_BIT:
scratch &= 0x7f;
break;
case BUS_32_BIT:
/* Negotiate 16_BITS */
bus_width = BUS_16_BIT;
case BUS_16_BIT:
if(bootverbose)
printf("ahc%d: target "
"%d using 16Bit "
"transfers\n",
unit, target);
scratch |= 0x80;
break;
default:
break;
}
outb(HA_RETURN_1 + iobase,
bus_width | SEND_WDTR);
}
ahc->needwdtr &= ~targ_mask;
ahc->wdtrpending &= ~targ_mask;
outb(HA_TARG_SCRATCH + iobase + scratch_offset,
scratch);
outb(SCSIRATE + iobase, scratch);
break;
}
case MSG_REJECT:
{
/*
* What we care about here is if we had an
* outstanding SDTR or WDTR message for this
* target. If we did, this is a signal that
* the target is refusing negotiation.
*/
u_char targ_scratch;
targ_scratch = inb(HA_TARG_SCRATCH + iobase
+ scratch_offset);
if(ahc->wdtrpending & targ_mask){
/* note 8bit xfers and clear flag */
targ_scratch &= 0x7f;
ahc->needwdtr &= ~targ_mask;
ahc->wdtrpending &= ~targ_mask;
printf("ahc%d:%c:%d: refuses "
"WIDE negotiation. Using "
"8bit transfers\n",
unit, channel, target);
}
else if(ahc->sdtrpending & targ_mask){
/* note asynch xfers and clear flag */
targ_scratch &= 0xf0;
ahc->needsdtr &= ~targ_mask;
ahc->sdtrpending &= ~targ_mask;
printf("ahc%d:%c:%d: refuses "
"syncronous negotiation. Using "
"asyncronous transfers\n",
unit, channel, target);
}
else {
/*
* Otherwise, we ignore it.
*/
#ifdef AHC_DEBUG
if(ahc_debug & AHC_SHOWMISC)
printf("ahc%d:%c:%d: Message
reject -- ignored\n",
unit, channel, target);
#endif
break;
}
outb(HA_TARG_SCRATCH + iobase + scratch_offset,
targ_scratch);
outb(SCSIRATE + iobase, targ_scratch);
break;
}
case BAD_STATUS:
{
int scb_index;
/* The sequencer will notify us when a command
* has an error that would be of interest to
* the kernel. This allows us to leave the sequencer
* running in the common case of command completes
* without error.
*/
scb_index = inb(SCBPTR + iobase);
scb = ahc->scbarray[scb_index];
/*
* Set the default return value to 0 (don't
* send sense). The sense code with change
* this if needed and this reduces code
* duplication.
*/
outb(HA_RETURN_1 + iobase, 0);
if (!scb || !(scb->flags & SCB_ACTIVE)) {
printf("ahc%d:%c:%d: ahcintr - referenced scb "
"not valid during seqint 0x%x scb(%d)\n",
unit, channel, target, intstat, scb_index);
goto clear;
}
xs = scb->xs;
ahc_getscb(iobase, scb);
#ifdef AHC_DEBUG
if((ahc_debug & AHC_SHOWSCBS)
&& xs->sc_link->target == DEBUGTARG)
ahc_print_scb(scb);
#endif
xs->status = scb->target_status;
switch(scb->target_status){
case SCSI_OK:
printf("ahc%d: Interrupted for staus of"
" 0???\n", unit);
break;
case SCSI_CHECK:
#ifdef AHC_DEBUG
if(ahc_debug & AHC_SHOWSENSE)
{
sc_print_addr(xs->sc_link);
printf("requests Check Status\n");
}
#endif
if((xs->error == XS_NOERROR) &&
!(scb->flags & SCB_SENSE)) {
u_char control = scb->control;
u_short active;
struct ahc_dma_seg *sg = scb->ahc_dma;
struct scsi_sense *sc = &(scb->sense_cmd);
u_char tcl = scb->target_channel_lun;
#ifdef AHC_DEBUG
if(ahc_debug & AHC_SHOWSENSE)
{
sc_print_addr(xs->sc_link);
printf("Sending Sense\n");
}
#endif
bzero(scb, SCB_DOWN_SIZE);
scb->control |= control & SCB_DISCENB;
scb->flags |= SCB_SENSE;
sc->op_code = REQUEST_SENSE;
sc->byte2 = xs->sc_link->lun << 5;
sc->length = sizeof(struct scsi_sense_data);
sc->control = 0;
sg->addr = KVTOPHYS(&xs->sense);
sg->len = sizeof(struct scsi_sense_data);
scb->target_channel_lun = tcl;
scb->SG_segment_count = 1;
scb->SG_list_pointer = KVTOPHYS(sg);
scb->cmdpointer = KVTOPHYS(sc);
scb->cmdlen = sizeof(*sc);
scb->data = sg->addr;
scb->datalen[0] =
sg->len & 0xff;
scb->datalen[1] =
(sg->len >> 8) & 0xff;
scb->datalen[2] =
(sg->len >> 16) & 0xff;
outb(SCBCNT + iobase, 0x80);
outsb(SCBARRAY+iobase,scb,SCB_DOWN_SIZE);
outb(SCBCNT + iobase, 0);
outb(SCBARRAY+iobase+30,SCB_LIST_NULL);
/*
* Ensure that the target is "BUSY"
* so we don't get overlapping
* commands if we happen to be doing
* tagged I/O.
*/
active = inb(HA_ACTIVE0 + iobase)
| (inb(HA_ACTIVE1 + iobase) << 8);
active |= targ_mask;
outb(HA_ACTIVE0 + iobase,active & 0xff);
outb(HA_ACTIVE1 + iobase,
(active >> 8) & 0xff);
ahc_add_waiting_scb(iobase, scb,
list_head);
outb(HA_RETURN_1 + iobase, SEND_SENSE);
break;
}
/*
* Clear the SCB_SENSE Flag and have
* the sequencer do a normal command
* complete with either a "DRIVER_STUFFUP"
* error or whatever other error condition
* we already had.
*/
scb->flags &= ~SCB_SENSE;
if(xs->error == XS_NOERROR)
xs->error = XS_DRIVER_STUFFUP;
break;
case SCSI_BUSY:
xs->error = XS_BUSY;
sc_print_addr(xs->sc_link);
printf("Target Busy\n");
break;
case SCSI_QUEUE_FULL:
/*
* The upper level SCSI code will eventually
* handle this properly.
*/
sc_print_addr(xs->sc_link);
printf("Queue Full\n");
xs->error = XS_BUSY;
break;
default:
sc_print_addr(xs->sc_link);
printf("unexpected targ_status: %x\n",
scb->target_status);
xs->error = XS_DRIVER_STUFFUP;
break;
}
break;
}
case RESIDUAL:
{
int scb_index;
scb_index = inb(SCBPTR + iobase);
scb = ahc->scbarray[scb_index];
xs = scb->xs;
/*
* Don't clobber valid resid info with
* a resid coming from a check sense
* operation.
*/
if(!(scb->flags & SCB_SENSE)) {
scb->xs->resid = (inb(iobase+SCBARRAY+17) << 16) |
(inb(iobase+SCBARRAY+16) << 8) |
inb(iobase+SCBARRAY+15);
xs->flags |= SCSI_RESID_VALID;
#ifdef AHC_DEBUG
if(ahc_debug & AHC_SHOWMISC) {
sc_print_addr(xs->sc_link);
printf("Handled Residual of %d bytes\n"
"SG_COUNT == %d\n",
scb->xs->resid,
inb(SCBARRAY+18 + iobase));
}
#endif
}
break;
}
case ABORT_TAG:
{
int scb_index;
scb_index = inb(SCBPTR + iobase);
scb = ahc->scbarray[scb_index];
xs = scb->xs;
/*
* We didn't recieve a valid tag back from
* the target on a reconnect.
*/
sc_print_addr(xs->sc_link);
printf("invalid tag recieved -- sending ABORT_TAG\n");
scb->xs->error = XS_DRIVER_STUFFUP;
untimeout(ahc_timeout, (caddr_t)scb);
ahc_done(unit, scb);
break;
}
case AWAITING_MSG:
{
int scb_index;
scb_index = inb(SCBPTR + iobase);
scb = ahc->scbarray[scb_index];
/*
* This SCB had a zero length command, informing
* the sequencer that we wanted to send a special
* message to this target. We only do this for
* BUS_DEVICE_RESET messages currently.
*/
if(scb->flags & SCB_DEVICE_RESET)
{
outb(HA_MSG_START + iobase,
MSG_BUS_DEVICE_RESET);
outb(HA_MSG_LEN + iobase, 1);
}
else
panic("ahcintr: AWAITING_MSG for an SCB that"
"does not have a waiting message");
break;
}
case IMMEDDONE:
{
/*
* Take care of device reset messages
*/
u_char scbindex = inb(SCBPTR + iobase);
scb = ahc->scbarray[scbindex];
if(scb->flags & SCB_DEVICE_RESET) {
u_char targ_scratch;
int found;
/*
* Go back to async/narrow transfers and
* renegotiate.
*/
ahc_unbusy_target(target, channel, iobase);
ahc->needsdtr |= ahc->needsdtr_orig & targ_mask;
ahc->needwdtr |= ahc->needwdtr_orig & targ_mask;
ahc->sdtrpending &= ~targ_mask;
ahc->wdtrpending &= ~targ_mask;
targ_scratch = inb(HA_TARG_SCRATCH + iobase
+ scratch_offset);
targ_scratch &= SXFR;
outb(HA_TARG_SCRATCH + iobase + scratch_offset,
targ_scratch);
found = ahc_reset_device(unit, ahc, target,
channel, SCB_LIST_NULL,
XS_NOERROR);
#ifdef AHC_DEBUG
if(ahc_debug & AHC_SHOWABORTS) {
sc_print_addr(scb->xs->sc_link);
printf("Bus Device Reset delivered. "
"%d SCBs aborted\n", found);
}
#endif
}
else
panic("ahcintr: Immediate complete for "
"unknown operation.");
break;
}
default:
printf("ahc: seqint, "
"intstat == 0x%x, scsisigi = 0x%x\n",
intstat, inb(SCSISIGI + iobase));
break;
}
clear:
/*
* Clear the upper byte that holds SEQINT status
* codes and clear the SEQINT bit.
*/
outb(CLRINT + iobase, CLRSEQINT);
/*
* The sequencer is paused immediately on
* a SEQINT, so we should restart it when
* we leave this section.
*/
UNPAUSE_SEQUENCER(ahc);
}
if (intstat & SCSIINT) {
int scb_index = inb(SCBPTR + iobase);
status = inb(SSTAT1 + iobase);
scb = ahc->scbarray[scb_index];
if (!scb || !(scb->flags & SCB_ACTIVE)) {
printf("ahc%d: ahcintr - referenced scb not "
"valid during scsiint 0x%x scb(%d)\n",
unit, status, scb_index);
outb(CLRSINT1 + iobase, status);
UNPAUSE_SEQUENCER(ahc);
outb(CLRINT + iobase, CLRSCSIINT);
scb = NULL;
goto cmdcomplete;
}
xs = scb->xs;
if (status & SELTO) {
u_char waiting;
u_char flags;
outb(SCSISEQ + iobase, ENRSELI);
xs->error = XS_TIMEOUT;
/*
* Clear any pending messages for the timed out
* target, and mark the target as free
*/
flags = inb( HA_FLAGS + iobase );
outb(HA_FLAGS + iobase,
flags & ~ACTIVE_MSG);
ahc_unbusy_target(xs->sc_link->target,
((long)xs->sc_link->fordriver & SELBUSB)
? 'B' : 'A',
iobase);
outb(SCBARRAY + iobase, SCB_NEEDDMA);
outb(CLRSINT1 + iobase, CLRSELTIMEO);
outb(CLRINT + iobase, CLRSCSIINT);
/* Shift the waiting for selection queue forward */
waiting = inb(WAITING_SCBH + iobase);
outb(SCBPTR + iobase, waiting);
waiting = inb(SCBARRAY + iobase + 30);
outb(WAITING_SCBH + iobase, waiting);
RESTART_SEQUENCER(ahc);
}
else if (status & SCSIPERR) {
sc_print_addr(xs->sc_link);
printf("parity error\n");
xs->error = XS_DRIVER_STUFFUP;
outb(CLRSINT1 + iobase, CLRSCSIPERR);
UNPAUSE_SEQUENCER(ahc);
outb(CLRINT + iobase, CLRSCSIINT);
scb = NULL;
}
else if (!(status & BUSFREE)) {
sc_print_addr(xs->sc_link);
printf("Unknown SCSIINT. Status = 0x%x\n", status);
outb(CLRSINT1 + iobase, status);
UNPAUSE_SEQUENCER(ahc);
outb(CLRINT + iobase, CLRSCSIINT);
scb = NULL;
}
if(scb != NULL) {
/* We want to process the command */
untimeout(ahc_timeout, (caddr_t)scb);
ahc_done(unit, scb);
}
}
cmdcomplete:
if (intstat & CMDCMPLT) {
int scb_index;
do {
scb_index = inb(QOUTFIFO + iobase);
scb = ahc->scbarray[scb_index];
if (!scb || !(scb->flags & SCB_ACTIVE)) {
printf("ahc%d: WARNING "
"no command for scb %d (cmdcmplt)\n"
"QOUTCNT == %d\n",
unit, scb_index, inb(QOUTCNT + iobase));
outb(CLRINT + iobase, CLRCMDINT);
continue;
}
outb(CLRINT + iobase, CLRCMDINT);
untimeout(ahc_timeout, (caddr_t)scb);
ahc_done(unit, scb);
} while (inb(QOUTCNT + iobase));
}
return 1;
}
int
enable_seeprom(u_long offset,
u_short CS, /* chip select */
u_short CK, /* clock */
u_short DO, /* data out */
u_short DI, /* data in */
u_short RDY, /* ready */
u_short MS /* mode select */)
{
int wait;
/*
* Request access of the memory port. When access is
* granted, SEERDY will go high. We use a 1 second
* timeout which should be near 1 second more than
* is needed. Reason: after the chip reset, there
* should be no contention.
*/
outb(offset, MS);
wait = 1000; /* 1 second timeout in msec */
while (--wait && ((inb(offset) & RDY) == 0)) {
DELAY (1000); /* delay 1 msec */
}
if ((inb(offset) & RDY) == 0) {
outb (offset, 0);
return (0);
}
return(1);
}
void
release_seeprom(u_long offset,
u_short CS, /* chip select */
u_short CK, /* clock */
u_short DO, /* data out */
u_short DI, /* data in */
u_short RDY, /* ready */
u_short MS /* mode select */)
{
/* Release access to the memory port and the serial EEPROM. */
outb(offset, 0);
}
/*
* We have a scb which has been processed by the
* adaptor, now we look to see how the operation
* went.
*/
void
ahc_done(unit, scb)
int unit;
struct scb *scb;
{
struct scsi_xfer *xs = scb->xs;
SC_DEBUG(xs->sc_link, SDEV_DB2, ("ahc_done\n"));
/*
* Put the results of the operation
* into the xfer and call whoever started it
*/
if(scb->flags & SCB_SENSE)
xs->error = XS_SENSE;
if ((xs->flags & SCSI_ERR_OK) && !(xs->error == XS_SENSE)) {
/* All went correctly OR errors expected */
xs->error = XS_NOERROR;
}
xs->flags |= ITSDONE;
#ifdef AHC_TAGENABLE
if(xs->cmd->opcode == 0x12 && xs->error == XS_NOERROR)
{
struct ahc_data *ahc = ahcdata[unit];
struct scsi_inquiry_data *inq_data;
u_short mask = 0x01 << (xs->sc_link->target |
(scb->target_channel_lun & 0x08));
/*
* Sneak a look at the results of the SCSI Inquiry
* command and see if we can do Tagged queing. This
* should really be done by the higher level drivers.
*/
inq_data = (struct scsi_inquiry_data *)xs->data;
if(((inq_data->device & SID_TYPE) == 0)
&& (inq_data->flags & SID_CmdQue)
&& !(ahc->tagenable & mask))
{
/*
* Disk type device and can tag
*/
printf("ahc%d: target %d Tagged Queuing Device\n",
unit, xs->sc_link->target);
ahc->tagenable |= mask;
#ifdef QUEUE_FULL_SUPPORTED
xs->sc_link->opennings += 2; */
#endif
}
}
#endif
ahc_free_scb(unit, scb, xs->flags);
scsi_done(xs);
}
/*
* Start the board, ready for normal operation
*/
int
ahc_init(unit)
int unit;
{
struct ahc_data *ahc = ahcdata[unit];
u_long iobase = ahc->baseport;
u_char scsi_conf, sblkctl, i, host_id;
int intdef, max_targ = 15, wait, have_seeprom = 0;
int bios_disabled = 0;
struct seeprom_config sc;
/*
* Assume we have a board at this stage
* Find out the configured interupt and the card type.
*/
#ifdef AHC_DEBUG
if(ahc_debug & AHC_SHOWMISC)
printf("ahc%d: scb %d bytes; ahc_dma %d bytes\n",
unit, sizeof(struct scb), sizeof(struct ahc_dma_seg));
#endif /* AHC_DEBUG */
if(bootverbose)
printf("ahc%d: reading board settings\n", unit);
/* Save the IRQ type before we do a chip reset */
ahc->unpause = (inb(HCNTRL + iobase) & IRQMS) | INTEN;
ahc->pause = ahc->unpause | PAUSE;
outb(HCNTRL + iobase, CHIPRST | ahc->pause);
/*
* Ensure that the reset has finished
*/
wait = 1000;
while (wait--) {
DELAY(1000);
if(!(inb(HCNTRL + iobase) & CHIPRST))
break;
}
if(wait == 0) {
printf("ahc%d: WARNING - Failed chip reset! "
"Trying to initialize anyway.\n", unit);
/* Forcibly clear CHIPRST */
outb(HCNTRL + iobase, ahc->pause);
}
switch( ahc->type ) {
case AHC_AIC7770:
case AHC_274:
case AHC_284:
{
u_char hostconf;
if(ahc->type == AHC_274) {
printf("ahc%d: 274x ", unit);
if((inb(HA_274_BIOSCTRL + iobase) & BIOSMODE)
== BIOSDISABLED)
bios_disabled = 1;
}
else if(ahc->type == AHC_284)
printf("ahc%d: 284x ", unit);
else
printf("ahc%d: Motherboard ", unit);
ahc->maxscbs = 0x4;
/* Should we only do this for the 27/284x? */
/* Setup the FIFO threshold and the bus off time */
hostconf = inb(HA_HOSTCONF + iobase);
outb(BUSSPD + iobase, hostconf & DFTHRSH);
outb(BUSTIME + iobase, (hostconf << 2) & BOFF);
break;
}
case AHC_AIC7850:
case AHC_AIC7870:
case AHC_394:
case AHC_294:
host_id = 0x07; /* default to SCSI ID 7 for 7850 */
if (ahc->type & AHC_AIC7870) {
unsigned short *scarray = (u_short *)&sc;
unsigned short checksum = 0;
if(bootverbose)
printf("ahc%d: Reading SEEPROM...", unit);
have_seeprom = enable_seeprom (iobase + SEECTL,
SEECS, SEECK, SEEDO, SEEDI, SEERDY, SEEMS);
if (have_seeprom) {
have_seeprom = read_seeprom (iobase + SEECTL,
(u_short *)&sc, ahc->flags & AHC_CHNLB,
sizeof(sc)/2, SEECS, SEECK, SEEDO,
SEEDI, SEERDY, SEEMS);
release_seeprom (iobase + SEECTL, SEECS, SEECK,
SEEDO, SEEDI, SEERDY, SEEMS);
if (have_seeprom) {
/* Check checksum */
for (i = 0;i < (sizeof(sc)/2 - 1);i = i + 1)
checksum = checksum + scarray[i];
if (checksum != sc.checksum) {
printf ("checksum error");
have_seeprom = 0;
}
else {
if(bootverbose)
printf("done.\n");
host_id = (sc.brtime_id & CFSCSIID);
}
}
}
if (!have_seeprom) {
printf("\nahc%d: SEEPROM read failed, "
"using leftover BIOS values\n", unit);
host_id = 0x7;
}
}
ahc->maxscbs = 0x10;
if(ahc->type == AHC_394)
printf("ahc%d: 3940 ", unit);
else if(ahc->type == AHC_294)
printf("ahc%d: 2940 ", unit);
else if(ahc->type == AHC_AIC7850){
printf("ahc%d: aic7850 ", unit);
ahc->maxscbs = 0x03;
}
else
printf("ahc%d: aic7870 ", unit);
outb(DSPCISTATUS + iobase, 0xc0 /* DFTHRSH == 100% */);
/*
* XXX Use SCSI ID from SEEPROM if we have it; otherwise
* its hardcoded to 7 until we can read it from NVRAM.
*/
outb(HA_SCSICONF + iobase, host_id | 0xc0 /* DFTHRSH = 100% */);
/* In case we are a wide card */
outb(HA_SCSICONF + 1 + iobase, host_id);
break;
default:
};
/* Determine channel configuration and who we are on the scsi bus. */
switch ( (sblkctl = inb(SBLKCTL + iobase) & 0x0a) ) {
case 0:
ahc->our_id = (inb(HA_SCSICONF + iobase) & HSCSIID);
if(ahc->type == AHC_394)
printf("Channel %c, SCSI Id=%d, ",
ahc->flags & AHC_CHNLB ? 'B' : 'A',
ahc->our_id);
else
printf("Single Channel, SCSI Id=%d, ", ahc->our_id);
outb(HA_FLAGS + iobase, SINGLE_BUS);
break;
case 2:
ahc->our_id = (inb(HA_SCSICONF + 1 + iobase) & HWSCSIID);
if(ahc->type == AHC_394)
printf("Wide Channel %c, SCSI Id=%d, ",
ahc->flags & AHC_CHNLB ? 'B' : 'A',
ahc->our_id);
else
printf("Wide Channel, SCSI Id=%d, ", ahc->our_id);
ahc->type |= AHC_WIDE;
outb(HA_FLAGS + iobase, WIDE_BUS);
break;
case 8:
ahc->our_id = (inb(HA_SCSICONF + iobase) & HSCSIID);
ahc->our_id_b = (inb(HA_SCSICONF + 1 + iobase) & HSCSIID);
printf("Twin Channel, A SCSI Id=%d, B SCSI Id=%d, ",
ahc->our_id, ahc->our_id_b);
ahc->type |= AHC_TWIN;
outb(HA_FLAGS + iobase, TWIN_BUS);
break;
default:
printf(" Unsupported adapter type. Ignoring\n");
return(-1);
}
/*
* Take the bus led out of diagnostic mode
*/
outb(SBLKCTL + iobase, sblkctl);
/*
* Number of SCBs that will be used. Rev E aic7770s supposedly
* can do 255 concurrent commands. Right now, we just ID the
* card until we can find out how this is done.
*/
if(!(ahc->type & AHC_AIC78X0))
{
/*
* See if we have a Rev E or higher
* aic7770. Anything below a Rev E will
* have a R/O autoflush disable configuration
* bit.
*/
u_char sblkctl_orig;
sblkctl_orig = inb(SBLKCTL + iobase);
sblkctl = sblkctl_orig ^ AUTOFLUSHDIS;
outb(SBLKCTL + iobase, sblkctl);
sblkctl = inb(SBLKCTL + iobase);
if(sblkctl != sblkctl_orig)
{
printf("aic7770 >= Rev E, ");
/*
* Ensure autoflush is enabled
*/
sblkctl &= ~AUTOFLUSHDIS;
outb(SBLKCTL + iobase, sblkctl);
}
else
printf("aic7770 <= Rev C, ");
}
else if(ahc->type & AHC_AIC7850)
printf("aic7850, ");
else
printf("aic7870, ");
if(ahc->flags & AHC_EXTSCB) {
/*
* This adapter has external SCB memory.
* Walk the SCBs to determine how many there are.
*/
for(i = 0; i < AHC_SCB_MAX; i++) {
outb(SCBPTR + iobase, i);
outb(SCBARRAY + iobase, 0xaa);
if(inb(SCBARRAY + iobase) == 0xaa){
outb(SCBARRAY + iobase, 0x55);
if(inb(SCBARRAY + iobase) == 0x55) {
continue;
}
}
break;
}
ahc->maxscbs = i;
}
printf("%d SCBs\n", ahc->maxscbs);
if(!(ahc->type & AHC_AIC78X0) && bootverbose) {
if(ahc->pause & IRQMS)
printf("ahc%d: Using Level Sensitive Interrupts\n",
unit);
else
printf("ahc%d: Using Edge Triggered Interrupts\n",
unit);
}
if(!(ahc->type & AHC_AIC78X0)){
/*
* The AIC78X0 cards are PCI, so we get their interrupt from the PCI
* BIOS.
*/
intdef = inb(INTDEF + iobase);
switch (intdef & 0xf) {
case 9:
ahc->vect = 9;
break;
case 10:
ahc->vect = 10;
break;
case 11:
ahc->vect = 11;
break;
case 12:
ahc->vect = 12;
break;
case 14:
ahc->vect = 14;
break;
case 15:
ahc->vect = 15;
break;
default:
printf("illegal irq setting\n");
return (EIO);
}
}
/* Set the SCSI Id, SXFRCTL1, and SIMODE1, for both channels */
if( ahc->type & AHC_TWIN)
{
/*
* The device is gated to channel B after a chip reset,
* so set those values first
*/
outb(SCSIID + iobase, ahc->our_id_b);
scsi_conf = inb(HA_SCSICONF + 1 + iobase) & (ENSPCHK|STIMESEL);
outb(SXFRCTL1 + iobase, scsi_conf|ENSTIMER|ACTNEGEN|STPWEN);
outb(SIMODE1 + iobase, ENSELTIMO|ENSCSIPERR);
/* Reset the bus */
outb(SCSISEQ + iobase, SCSIRSTO);
DELAY(1000);
outb(SCSISEQ + iobase, 0);
/* Select Channel A */
outb(SBLKCTL + iobase, 0);
}
outb(SCSIID + iobase, ahc->our_id);
scsi_conf = inb(HA_SCSICONF + iobase) & (ENSPCHK|STIMESEL);
outb(SXFRCTL1 + iobase, scsi_conf|ENSTIMER|ACTNEGEN|STPWEN);
outb(SIMODE1 + iobase, ENSELTIMO|ENSCSIPERR);
/* Reset the bus */
outb(SCSISEQ + iobase, SCSIRSTO);
DELAY(1000);
outb(SCSISEQ + iobase, 0);
/*
* Look at the information that board initialization or
* the board bios has left us. In the lower four bits of each
* target's scratch space any value other than 0 indicates
* that we should initiate syncronous transfers. If it's zero,
* the user or the BIOS has decided to disable syncronous
* negotiation to that target so we don't activate the needsdr
* flag.
*/
ahc->needsdtr_orig = 0;
ahc->needwdtr_orig = 0;
/* Grab the disconnection disable table and invert it for our needs */
if(have_seeprom)
ahc->discenable = 0;
else if(bios_disabled){
printf("ahc%d: Host Adapter Bios disabled. Using default SCSI "
"device parameters\n", unit);
ahc->discenable = 0xff;
}
else
ahc->discenable = ~(inw(HA_DISC_DSB + iobase));
if(!(ahc->type & AHC_WIDE))
max_targ = 7;
for(i = 0; i <= max_targ; i++){
u_char target_settings;
if (have_seeprom) {
target_settings = (sc.device_flags[i] & CFXFER) << 4;
if (sc.device_flags[i] & CFSYNCH)
ahc->needsdtr_orig |= (0x01 << i);
if (sc.device_flags[i] & CFWIDEB)
ahc->needwdtr_orig |= (0x01 << i);
if (sc.device_flags[i] & CFDISC)
ahc->discenable |= (0x01 << i);
}
else if (bios_disabled) {
target_settings = 0; /* 10MHz */
ahc->needsdtr_orig |= (0x01 << i);
ahc->needwdtr_orig |= (0x01 << i);
}
else {
/* Take the settings leftover in scratch RAM. */
target_settings = inb(HA_TARG_SCRATCH + i + iobase);
if(target_settings & 0x0f){
ahc->needsdtr_orig |= (0x01 << i);
/*Default to a asyncronous transfers(0 offset)*/
target_settings &= 0xf0;
}
if(target_settings & 0x80){
ahc->needwdtr_orig |= (0x01 << i);
/*
* We'll set the Wide flag when we
* are successful with Wide negotiation,
* so turn it off for now so we aren't
* confused.
*/
target_settings &= 0x7f;
}
}
outb(HA_TARG_SCRATCH+i+iobase,target_settings);
}
/*
* If we are not a WIDE device, forget WDTR. This
* makes the driver work on some cards that don't
* leave these fields cleared when the BIOS is not
* installed.
*/
if(!(ahc->type & AHC_WIDE))
ahc->needwdtr_orig = 0;
ahc->needsdtr = ahc->needsdtr_orig;
ahc->needwdtr = ahc->needwdtr_orig;
ahc->sdtrpending = 0;
ahc->wdtrpending = 0;
ahc->tagenable = 0;
/*
* Clear the control byte for every SCB so that the sequencer
* doesn't get confused and think that one of them is valid
*/
for(i = 0; i < ahc->maxscbs; i++) {
outb(SCBPTR + iobase, i);
outb(SCBARRAY + iobase, 0);
}
#ifdef AHC_DEBUG
if(ahc_debug & AHC_SHOWMISC)
printf("NEEDSDTR == 0x%x\nNEEDWDTR == 0x%x\n"
"DISCENABLE == 0x%x\n", ahc->needsdtr,
ahc->needwdtr, ahc->discenable);
#endif
/*
* Set the number of availible SCBs
*/
outb(HA_SCBCOUNT + iobase, ahc->maxscbs);
/* We don't have any busy targets right now */
outb( HA_ACTIVE0 + iobase, 0 );
outb( HA_ACTIVE1 + iobase, 0 );
/* We don't have any waiting selections */
outb( WAITING_SCBH + iobase, SCB_LIST_NULL );
outb( WAITING_SCBT + iobase, SCB_LIST_NULL );
/*
* Load the Sequencer program and Enable the adapter.
* Place the aic7xxx in fastmode which makes a big
* difference when doing many small block transfers.
*/
if(bootverbose)
printf("ahc%d: Downloading Sequencer Program...", unit);
ahc_loadseq(iobase);
if(bootverbose)
printf("Done\n");
outb(SEQCTL + iobase, FASTMODE);
if (!(ahc->type & AHC_AIC78X0))
outb(BCTL + iobase, ENABLE);
UNPAUSE_SEQUENCER(ahc);
/*
* Note that we are going and return (to probe)
*/
ahc->flags = AHC_INIT;
return (0);
}
void
ahcminphys(bp)
struct buf *bp;
{
/*
* Even though the card can transfer up to 16megs per command
* we are limited by the number of segments in the dma segment
* list that we can hold. The worst case is that all pages are
* discontinuous physically, hense the "page per segment" limit
* enforced here.
*/
if (bp->b_bcount > ((AHC_NSEG - 1) * PAGESIZ)) {
bp->b_bcount = ((AHC_NSEG - 1) * PAGESIZ);
}
}
/*
* start a scsi operation given the command and
* the data address, target, and lun all of which
* are stored in the scsi_xfer struct
*/
int32
ahc_scsi_cmd(xs)
struct scsi_xfer *xs;
{
struct scb *scb = NULL;
struct ahc_dma_seg *sg;
int seg; /* scatter gather seg being worked on */
int thiskv;
physaddr thisphys, nextphys;
int unit = xs->sc_link->adapter_unit;
u_short mask = (0x01 << (xs->sc_link->target
| ((u_long)xs->sc_link->fordriver & 0x08)));
int bytes_this_seg, bytes_this_page, datalen, flags;
struct ahc_data *ahc = ahcdata[unit];
int s;
SC_DEBUG(xs->sc_link, SDEV_DB2, ("ahc_scsi_cmd\n"));
/*
* get an scb to use. If the transfer
* is from a buf (possibly from interrupt time)
* then we can't allow it to sleep
*/
flags = xs->flags;
if (flags & ITSDONE) {
printf("ahc%d: Already done?", unit);
xs->flags &= ~ITSDONE;
}
if (!(flags & INUSE)) {
printf("ahc%d: Not in use?", unit);
xs->flags |= INUSE;
}
if (!(scb = ahc_get_scb(unit, flags))) {
xs->error = XS_DRIVER_STUFFUP;
return (TRY_AGAIN_LATER);
}
SC_DEBUG(xs->sc_link, SDEV_DB3, ("start scb(%p)\n", scb));
scb->xs = xs;
if (flags & SCSI_RESET)
scb->flags |= SCB_DEVICE_RESET|SCB_IMMED;
/*
* Put all the arguments for the xfer in the scb
*/
if(ahc->tagenable & mask)
scb->control |= SCB_TE;
if(ahc->discenable & mask)
scb->control |= SCB_DISCENB;
if((ahc->needwdtr & mask) && !(ahc->wdtrpending & mask))
{
scb->control |= SCB_NEEDWDTR;
ahc->wdtrpending |= mask;
}
else if((ahc->needsdtr & mask) && !(ahc->sdtrpending & mask))
{
scb->control |= SCB_NEEDSDTR;
ahc->sdtrpending |= mask;
}
scb->target_channel_lun = ((xs->sc_link->target << 4) & 0xF0) |
((u_long)xs->sc_link->fordriver & 0x08) |
(xs->sc_link->lun & 0x07);
scb->cmdlen = xs->cmdlen;
scb->cmdpointer = KVTOPHYS(xs->cmd);
xs->resid = 0;
xs->status = 0;
if (xs->datalen) { /* should use S/G only if not zero length */
scb->SG_list_pointer = KVTOPHYS(scb->ahc_dma);
sg = scb->ahc_dma;
seg = 0;
{
/*
* Set up the scatter gather block
*/
SC_DEBUG(xs->sc_link, SDEV_DB4,
("%ld @%p:- ", xs->datalen, xs->data));
datalen = xs->datalen;
thiskv = (int) xs->data;
thisphys = KVTOPHYS(thiskv);
while ((datalen) && (seg < AHC_NSEG)) {
bytes_this_seg = 0;
/* put in the base address */
sg->addr = thisphys;
SC_DEBUGN(xs->sc_link, SDEV_DB4, ("0x%lx",
thisphys));
/* do it at least once */
nextphys = thisphys;
while ((datalen) && (thisphys == nextphys)) {
/*
* This page is contiguous (physically)
* with the the last, just extend the
* length
*/
/* how far to the end of the page */
nextphys = (thisphys & (~(PAGESIZ - 1)))
+ PAGESIZ;
bytes_this_page = nextphys - thisphys;
/**** or the data ****/
bytes_this_page = min(bytes_this_page
,datalen);
bytes_this_seg += bytes_this_page;
datalen -= bytes_this_page;
/* get more ready for the next page */
thiskv = (thiskv & (~(PAGESIZ - 1)))
+ PAGESIZ;
if (datalen)
thisphys = KVTOPHYS(thiskv);
}
/*
* next page isn't contiguous, finish the seg
*/
SC_DEBUGN(xs->sc_link, SDEV_DB4,
("(0x%x)", bytes_this_seg));
sg->len = bytes_this_seg;
sg++;
seg++;
}
} /*end of iov/kv decision */
scb->SG_segment_count = seg;
/* Copy the first SG into the data pointer area */
scb->data = scb->ahc_dma->addr;
scb->datalen[0] = scb->ahc_dma->len & 0xff;
scb->datalen[1] = (scb->ahc_dma->len >> 8) & 0xff;
scb->datalen[2] = (scb->ahc_dma->len >> 16) & 0xff;
SC_DEBUGN(xs->sc_link, SDEV_DB4, ("\n"));
if (datalen) {
/* there's still data, must have run out of segs! */
printf("ahc_scsi_cmd%d: more than %d DMA segs\n",
unit, AHC_NSEG);
xs->error = XS_DRIVER_STUFFUP;
ahc_free_scb(unit, scb, flags);
return (HAD_ERROR);
}
}
else {
/*
* No data xfer, use non S/G values
*/
scb->SG_segment_count = 0;
scb->SG_list_pointer = 0;
scb->data = 0;
scb->datalen[0] = 0;
scb->datalen[1] = 0;
scb->datalen[2] = 0;
}
/*
* Usually return SUCCESSFULLY QUEUED
*/
#ifdef AHC_DEBUG
if((ahc_debug & AHC_SHOWSCBS) && (xs->sc_link->target == DEBUGTARG))
ahc_print_scb(scb);
#endif
if (!(flags & SCSI_NOMASK)) {
s = splbio();
ahc_send_scb(ahc, scb);
timeout(ahc_timeout, (caddr_t)scb, (xs->timeout * hz) / 1000);
splx(s);
SC_DEBUG(xs->sc_link, SDEV_DB3, ("cmd_sent\n"));
return (SUCCESSFULLY_QUEUED);
}
/*
* If we can't use interrupts, poll on completion
*/
ahc_send_scb(ahc, scb);
SC_DEBUG(xs->sc_link, SDEV_DB3, ("cmd_wait\n"));
do {
if (ahc_poll(unit, xs->timeout)) {
if (!(xs->flags & SCSI_SILENT))
printf("cmd fail\n");
printf("cmd fail\n");
ahc_scb_timeout(unit,ahc,scb);
return (HAD_ERROR);
}
} while (!(xs->flags & ITSDONE)); /* a non command complete intr */
if (xs->error) {
return (HAD_ERROR);
}
return (COMPLETE);
}
/*
* Return some information to the caller about
* the adapter and it's capabilities.
*/
u_int32
ahc_adapter_info(unit)
int unit;
{
return (2); /* 2 outstanding requests at a time per device */
}
/*
* A scb (and hence an scb entry on the board is put onto the
* free list.
*/
void
ahc_free_scb(unit, scb, flags)
int unit, flags;
struct scb *scb;
{
unsigned int opri;
struct ahc_data *ahc = ahcdata[unit];
opri = splbio();
scb->flags = SCB_FREE;
scb->next = ahc->free_scb;
ahc->free_scb = scb;
#ifdef AHC_DEBUG
ahc->activescbs--;
#endif
/*
* If there were none, wake abybody waiting for
* one to come free, starting with queued entries
*/
if (!scb->next) {
wakeup((caddr_t)&ahc->free_scb);
}
splx(opri);
}
/*
* Get a free scb
* If there are none, see if we can allocate a
* new one. Otherwise either return an error or sleep
*/
struct scb *
ahc_get_scb(unit, flags)
int unit, flags;
{
struct ahc_data *ahc = ahcdata[unit];
unsigned opri;
struct scb *scbp;
opri = splbio();
/*
* If we can and have to, sleep waiting for one to come free
* but only if we can't allocate a new one.
*/
while (!(scbp = ahc->free_scb)) {
if (ahc->numscbs < ahc->maxscbs) {
scbp = (struct scb *) malloc(sizeof(struct scb),
M_TEMP, M_NOWAIT);
if (scbp) {
physaddr scbaddr = KVTOPHYS(scbp);
u_long iobase = ahc->baseport;
u_char curscb;
bzero(scbp, sizeof(struct scb));
scbp->position = ahc->numscbs;
ahc->numscbs++;
scbp->flags = SCB_ACTIVE;
/*
* Place in the scbarray
* Never is removed. Position
* in ahc->scbarray is the scbarray
* position on the board we will
* load it into.
*/
ahc->scbarray[scbp->position] = scbp;
/*
* Initialize the host memory location
* of this SCB down on the board and
* flag that it should be DMA's before
* reference. Also set its psuedo
* next pointer (for use in the psuedo
* list of SCBs waiting for selection)
* to SCB_LIST_NULL.
*/
scbp->control = SCB_NEEDDMA;
scbp->host_scb = scbaddr;
scbp->next_waiting = SCB_LIST_NULL;
PAUSE_SEQUENCER(ahc);
curscb = inb(SCBPTR + iobase);
outb(SCBPTR + iobase, scbp->position);
outb(SCBCNT + iobase, 0x80);
outsb(SCBARRAY+iobase,scbp,31);
outb(SCBCNT + iobase, 0);
outb(SCBPTR + iobase, curscb);
UNPAUSE_SEQUENCER(ahc);
scbp->control = 0;
} else {
printf("ahc%d: Can't malloc SCB\n", unit);
}
break;
} else {
if (!(flags & SCSI_NOSLEEP)) {
tsleep((caddr_t)&ahc->free_scb, PRIBIO,
"ahcscb", 0);
continue;
}
break;
}
}
if (scbp) {
/* Get SCB from from free list */
ahc->free_scb = scbp->next;
scbp->control = 0;
scbp->flags = SCB_ACTIVE;
#ifdef AHC_DEBUG
ahc->activescbs++;
if((ahc_debug & AHC_SHOWMISC)
&& (ahc->activescbs == ahc->maxscbs))
printf("ahc%d: Max SCBs active\n", unit);
#endif
}
gottit:
splx(opri);
return (scbp);
}
void ahc_loadseq(iobase)
u_long iobase;
{
static unsigned char seqprog[] = {
# include "aic7xxx_seq.h"
};
outb(SEQCTL + iobase, PERRORDIS|SEQRESET|LOADRAM);
outsb(SEQRAM + iobase, seqprog, sizeof(seqprog));
outb(SEQCTL + iobase, FASTMODE|SEQRESET);
do {
outb(SEQCTL + iobase, SEQRESET|FASTMODE);
} while (inb(SEQADDR0 + iobase) != 0 &&
inb(SEQADDR1 + iobase != 0));
}
/*
* Function to poll for command completion when in poll mode
*/
int
ahc_poll(int unit, int wait)
{ /* in msec */
struct ahc_data *ahc = ahcdata[unit];
u_long iobase = ahc->baseport;
u_long stport = INTSTAT + iobase;
while (--wait) {
DELAY(1000);
if (inb(stport) & INT_PEND)
break;
} if (wait == 0) {
printf("ahc%d: board not responding\n", unit);
return (EIO);
}
ahcintr(unit);
return (0);
}
void
ahc_scb_timeout(unit, ahc, scb)
int unit;
struct ahc_data *ahc;
struct scb *scb;
{
u_long iobase = ahc->baseport;
int found = 0;
u_char scb_control;
char channel = scb->target_channel_lun & SELBUSB ? 'B': 'A';
/*
* Ensure that the card doesn't do anything
* behind our back.
*/
PAUSE_SEQUENCER(ahc);
/*
* First, determine if we want to do a bus
* reset or simply a bus device reset.
* If this is the first time that a transaction
* has timed out, just schedule a bus device
* reset. Otherwise, we reset the bus and
* abort all pending I/Os on that bus.
*/
if(scb->flags & SCB_ABORTED)
{
/*
* Been down this road before.
* Do a full bus reset.
*/
found = ahc_reset_channel(unit, ahc, channel, scb->position,
XS_TIMEOUT);
#ifdef AHC_DEBUG
if(ahc_debug & AHC_SHOWABORTS)
printf("ahc%d: Issued Channel %c Bus Reset #1. "
"%d SCBs aborted\n", unit, channel, found);
#endif
}
else {
/*
* Send a Bus Device Reset Message:
* The target we select to send the message to may
* be entirely different than the target pointed to
* by the scb that timed out. If the command is
* in the QINFIFO or the waiting for selection list,
* its not tying up the bus and isn't responsible
* for the delay so we pick off the active command
* which should be the SCB selected by SCBPTR. If
* its disconnected or active, we device reset the
* target scbp points to. Although it may be that
* this target is not responsible for the delay, it
* may also be that we're timing out on a command that
* just takes too much time, so we try the bus device
* reset there first.
*/
u_char active_scb, control;
struct scb *active_scbp;
active_scb = inb(SCBPTR + iobase);
active_scbp = ahc->scbarray[active_scb];
control = inb(SCBARRAY + iobase);
/* Test to see if scbp is disconnected */
outb(SCBPTR + iobase, scb->position);
if(inb(SCBARRAY + iobase) & SCB_DIS) {
scb->flags |= SCB_DEVICE_RESET|SCB_ABORTED;
scb->SG_segment_count = 0;
scb->SG_list_pointer = 0;
scb->data = 0;
scb->datalen[0] = 0;
scb->datalen[1] = 0;
scb->datalen[2] = 0;
outb(SCBCNT + iobase, 0x80);
outsb(SCBARRAY+iobase,scb,SCB_DOWN_SIZE);
outb(SCBCNT + iobase, 0);
ahc_add_waiting_scb(iobase, scb, list_second);
timeout(ahc_timeout, (caddr_t)scb,
(2 * hz) / 1000);
#ifdef AHC_DEBUG
if(ahc_debug & AHC_SHOWABORTS) {
sc_print_addr(scb->xs->sc_link);
printf("BUS DEVICE RESET message queued.\n");
}
#endif
UNPAUSE_SEQUENCER(ahc);
}
/* Is the active SCB really active? */
else if((active_scbp->flags & SCB_ACTIVE)
&& (control & SCB_NEEDDMA) == SCB_NEEDDMA) {
u_char flags = inb(HA_FLAGS + iobase);
if(flags & ACTIVE_MSG) {
/*
* If we're in a message phase, tacking on
* another message may confuse the target totally.
* The bus is probably wedged, so reset the
* channel.
*/
channel = (active_scbp->target_channel_lun & SELBUSB)
? 'B': 'A';
ahc_reset_channel(unit, ahc, channel, scb->position,
XS_TIMEOUT);
#ifdef AHC_DEBUG
if(ahc_debug & AHC_SHOWABORTS)
printf("ahc%d: Issued Channel %c Bus Reset #2. "
"%d SCBs aborted\n", unit, channel,
found);
#endif
}
else {
/*
* Load the message buffer and assert attention.
*/
active_scbp->flags |= SCB_DEVICE_RESET|SCB_ABORTED;
if(active_scbp != scb)
untimeout(ahc_timeout, (caddr_t)active_scbp);
timeout(ahc_timeout, (caddr_t)active_scbp,
(2 * hz) / 1000);
outb(HA_FLAGS + iobase, flags | ACTIVE_MSG);
outb(HA_MSG_LEN + iobase, 1);
outb(HA_MSG_START + iobase, MSG_BUS_DEVICE_RESET);
if(active_scbp->target_channel_lun
!= scb->target_channel_lun) {
/* Give scb a new lease on life */
timeout(ahc_timeout, (caddr_t)scb,
(scb->xs->timeout * hz) / 1000);
}
#ifdef AHC_DEBUG
if(ahc_debug & AHC_SHOWABORTS) {
sc_print_addr(active_scbp->xs->sc_link);
printf("BUS DEVICE RESET message queued.\n");
}
#endif
UNPAUSE_SEQUENCER(ahc);
}
}
else {
/*
* No active command to single out, so reset
* the bus for the timed out target.
*/
ahc_reset_channel(unit, ahc, channel, scb->position,
XS_TIMEOUT);
#ifdef AHC_DEBUG
if(ahc_debug & AHC_SHOWABORTS)
printf("ahc%d: Issued Channel %c Bus Reset #3. "
"%d SCBs aborted\n", unit, channel,
found);
#endif
}
}
}
void
ahc_timeout(void *arg1)
{
struct scb *scb = (struct scb *)arg1;
int unit;
struct ahc_data *ahc;
int s, h;
s = splbio();
unit = scb->xs->sc_link->adapter_unit;
ahc = ahcdata[unit];
printf("ahc%d: target %d, lun %d (%s%d) timed out\n", unit
,scb->xs->sc_link->target
,scb->xs->sc_link->lun
,scb->xs->sc_link->device->name
,scb->xs->sc_link->dev_unit);
h = splhigh();
if(ahc->in_timeout){
scb->next = ahc->timedout_scb;
ahc->timedout_scb = scb;
splx(h);
splx(s);
return;
}
else
ahc->in_timeout = 1;
splx(h);
while(scb) {
#ifdef SCSIDEBUG
show_scsi_cmd(scb->xs);
#endif
#ifdef AHC_DEBUG
if (ahc_debug & AHC_SHOWSCBS)
ahc_print_active_scb(ahc);
#endif /*AHC_DEBUG */
/*
* If it's immediate, don't try to abort it
*/
if (scb->flags & SCB_IMMED) {
scb->xs->retries = 0; /* I MEAN IT ! */
ahc_timeout_done(unit, scb);
}
else {
/* abort the operation that has timed out */
ahc_scb_timeout( unit, ahc, scb );
}
h = splhigh();
scb = ahc->timedout_scb;
if(scb)
ahc->timedout_scb = scb->next;
splx(h);
}
ahc->in_timeout = 0;
splx(s);
}
/*
* The device at the given target/channel has been reset. Abort
* all active and queued scbs for that target/channel.
*/
int
ahc_reset_device(unit, ahc, target, channel, timedout_scb, xs_error)
int unit;
struct ahc_data *ahc;
int target;
char channel;
u_char timedout_scb;
u_int32 xs_error;
{
u_long iobase = ahc->baseport;
struct scb *scbp;
u_char active_scb;
int i = 0;
int found = 0;
/* restore this when we're done */
active_scb = inb(SCBPTR + iobase);
/*
* Search the QINFIFO.
*/
{
int saved_queue[AHC_SCB_MAX];
int queued = inb(QINCNT + iobase);
for (i = 0; i < (queued - found); i++) {
saved_queue[i] = inb(QINFIFO + iobase);
scbp = ahc->scbarray[saved_queue[i]];
if (ahc_match_scb (scbp, target, channel)){
/*
* We found an scb that needs to be aborted.
*/
scbp->flags |= SCB_ABORTED;
scbp->xs->error |= xs_error;
if(scbp->position != timedout_scb)
untimeout(ahc_timeout, (caddr_t)scbp);
ahc_timeout_done (unit, scbp);
outb(SCBPTR + iobase, scbp->position);
outb(SCBARRAY + iobase, SCB_NEEDDMA);
i--;
found++;
}
}
/* Now put the saved scbs back. */
for (queued = 0; queued < i; queued++) {
outb (QINFIFO + iobase, saved_queue[queued]);
}
}
/*
* Search waiting for selection list.
*/
{
u_char next, prev;
next = inb(WAITING_SCBH + iobase); /* Start at head of list. */
prev = SCB_LIST_NULL;
while (next != SCB_LIST_NULL) {
scbp = ahc->scbarray[next];
/*
* Select the SCB.
*/
if (ahc_match_scb(scbp, target, channel)) {
next = ahc_abort_wscb(unit, scbp, prev,
iobase, timedout_scb, xs_error);
found++;
}
else {
outb(SCBPTR + iobase, scbp->position);
prev = next;
next = inb(SCBARRAY + iobase + 30);
}
}
}
/*
* Go through the entire SCB array now and look for
* commands for this target that are active. These
* are other (most likely tagged) commands that
* were disconnected when the reset occured.
*/
for(i = 0; i < ahc->numscbs; i++) {
scbp = ahc->scbarray[i];
if((scbp->flags & SCB_ACTIVE)
&& ahc_match_scb(scbp, target, channel)) {
/* Ensure the target is "free" */
ahc_unbusy_target(target, channel, iobase);
outb(SCBPTR + iobase, scbp->position);
outb(SCBARRAY + iobase, SCB_NEEDDMA);
scbp->flags |= SCB_ABORTED;
scbp->xs->error |= xs_error;
if(scbp->position != timedout_scb)
untimeout(ahc_timeout, (caddr_t)scbp);
ahc_timeout_done (unit, scbp);
found++;
}
}
outb(SCBPTR + iobase, active_scb);
return found;
}
/*
* Manipulate the waiting for selection list and return the
* scb that follows the one that we remove.
*/
u_char
ahc_abort_wscb (unit, scbp, prev, iobase, timedout_scb, xs_error)
int unit;
struct scb *scbp;
u_char prev;
u_long iobase;
u_char timedout_scb;
u_int32 xs_error;
{
u_char curscbp, next;
int target = ((scbp->target_channel_lun >> 4) & 0x0f);
char channel = (scbp->target_channel_lun & SELBUSB) ? 'B' : 'A';
/*
* Select the SCB we want to abort and
* pull the next pointer out of it.
*/
curscbp = inb(SCBPTR + iobase);
outb(SCBPTR + iobase, scbp->position);
next = inb(SCBARRAY + iobase + 30);
/* Clear the necessary fields */
outb(SCBARRAY + iobase, SCB_NEEDDMA);
outb(SCBARRAY + iobase + 30, SCB_LIST_NULL);
ahc_unbusy_target(target, channel, iobase);
/* update the waiting list */
if( prev == SCB_LIST_NULL )
/* First in the list */
outb(WAITING_SCBH + iobase, next);
else {
/*
* Select the scb that pointed to us
* and update its next pointer.
*/
outb(SCBPTR + iobase, prev);
outb(SCBARRAY + iobase + 30, next);
}
/* Update the tale pointer */
if(inb(WAITING_SCBT + iobase) == scbp->position)
outb(WAITING_SCBT + iobase, prev);
/*
* Point us back at the original scb position
* and inform the SCSI system that the command
* has been aborted.
*/
outb(SCBPTR + iobase, curscbp);
scbp->flags |= SCB_ABORTED;
scbp->xs->error |= xs_error;
if(scbp->position != timedout_scb)
untimeout(ahc_timeout, (caddr_t)scbp);
ahc_timeout_done (unit, scbp);
return next;
}
void
ahc_unbusy_target(target, channel, iobase)
u_char target;
char channel;
u_long iobase;
{
u_char active;
u_long active_port = HA_ACTIVE0 + iobase;
if(target > 0x07 || channel == 'B') {
/*
* targets on the Second channel or
* above id 7 store info in byte two
* of HA_ACTIVE
*/
active_port++;
}
active = inb(active_port);
active &= ~(0x01 << (target & 0x07));
outb(active_port, active);
}
void
ahc_reset_current_bus(iobase)
u_long iobase;
{
outb(SCSISEQ + iobase, SCSIRSTO);
DELAY(1000);
outb(SCSISEQ + iobase, 0);
}
int
ahc_reset_channel(unit, ahc, channel, timedout_scb, xs_error)
int unit;
struct ahc_data *ahc;
char channel;
u_char timedout_scb;
u_int32 xs_error;
{
u_long iobase = ahc->baseport;
u_char sblkctl;
char cur_channel;
u_long offset, offset_max;
int found;
/*
* Clean up all the state information for the
* pending transactions on this bus.
*/
found = ahc_reset_device(unit, ahc, ALL_TARGETS, channel,
timedout_scb, xs_error);
if(channel == 'B'){
ahc->needsdtr |= (ahc->needsdtr_orig & 0xff00);
ahc->sdtrpending &= 0x00ff;
outb(HA_ACTIVE1 + iobase, 0);
offset = HA_TARG_SCRATCH + iobase + 8;
offset_max = HA_TARG_SCRATCH + iobase + 16;
}
else if (ahc->type & AHC_WIDE){
ahc->needsdtr = ahc->needsdtr_orig;
ahc->needwdtr = ahc->needwdtr_orig;
ahc->sdtrpending = 0;
ahc->wdtrpending = 0;
outb(HA_ACTIVE0 + iobase, 0);
outb(HA_ACTIVE1 + iobase, 0);
offset = HA_TARG_SCRATCH + iobase;
offset_max = HA_TARG_SCRATCH + iobase + 16;
}
else{
ahc->needsdtr |= (ahc->needsdtr_orig & 0x00ff);
ahc->sdtrpending &= 0xff00;
outb(HA_ACTIVE0 + iobase, 0);
offset = HA_TARG_SCRATCH + iobase;
offset_max = HA_TARG_SCRATCH + iobase + 8;
}
for(;offset < offset_max;offset++) {
/*
* Revert to async/narrow transfers
* until we renegotiate.
*/
u_char targ_scratch;
targ_scratch = inb(offset);
targ_scratch &= SXFR;
outb(offset, targ_scratch);
}
/*
* Reset the bus and unpause/restart the controller
*/
/* Case 1: Command for another bus is active */
sblkctl = inb(SBLKCTL + iobase);
cur_channel = (sblkctl & SELBUSB) ? 'B' : 'A';
if(cur_channel != channel)
{
/*
* Stealthily reset the other bus
* without upsetting the current bus
*/
outb(SBLKCTL + iobase, sblkctl ^ SELBUSB);
ahc_reset_current_bus(iobase);
outb(SBLKCTL + iobase, sblkctl);
UNPAUSE_SEQUENCER(ahc);
}
/* Case 2: A command from this bus is active or we're idle */
else {
ahc_reset_current_bus(iobase);
RESTART_SEQUENCER(ahc);
}
return found;
}
int
ahc_match_scb (scb, target, channel)
struct scb *scb;
int target;
char channel;
{
int targ = (scb->target_channel_lun >> 4) & 0x0f;
char chan = (scb->target_channel_lun & SELBUSB) ? 'B' : 'A';
if (target == ALL_TARGETS)
return (chan == channel);
else
return ((chan == channel) && (targ == target));
}
void
ahc_timeout_done (unit, scbp)
int unit;
struct scb *scbp;
{
struct ahc_data *ahc = ahcdata[unit];
struct scb **prev_scb;
struct scb *cur_scb;
int h;
h = splhigh();
prev_scb = &ahc->timedout_scb;
cur_scb = ahc->timedout_scb;
while(cur_scb) {
if(cur_scb == scbp) {
*prev_scb = cur_scb->next;
break;
}
prev_scb = &cur_scb->next;
cur_scb = cur_scb->next;
}
splx(h);
ahc_done(unit, scbp);
}
Reference in New Issue View Git Blame Copy Permalink