534d3efa16
A while back, Warner changed the PCI bus code to reserve resources when enumerating devices and simply give devices the previously allocated resources when they call bus_alloc_resource(). This ensures that address ranges being decoded by a BAR are always allocated in the nexus0 device (or whatever device the PCI bus gets its address space from) even if a device driver is not attached to the device. This patch extends this behavior further: - To let the PCI bus distinguish between a resource being allocated by a device driver vs. merely being allocated by the bus, use rman_set_device() to assign the device to the bus when it is owned by the bus and to the child device when it is allocated by the child device's driver. We can now prevent a device driver from allocating the same device twice. Doing so could result in odd things like allocating duplicate virtual memory to map the resource on some archs and leaking the original mapping. - When a PCI device driver releases a resource, don't pass the request all the way up the tree and release it in the nexus (or similar device) since the BAR is still active and decoding. Otherwise, another device could later allocate the same range even though it is still in use. Instead, deactivate the resource and assign it back to the PCI bus using rman_set_device(). - pci_delete_resource() will actually completely free a BAR including attemping to disable it. - Disable BAR decoding via the command register when sizing a BAR in pci_alloc_map() which is used to allocate resources for a BAR when the BIOS/firmware did not assign a usable resource range during boot. This mirrors an earlier fix to pci_add_map() which is used when to size BARs during boot. - Move the activation of I/O decoding in the PCI command register into pci_activate_resource() instead of doing it in pci_alloc_resource(). Previously we could actually enable decoding before a BAR was initialized via pci_alloc_map(). Glanced at by: bsdimp
This is the top level of the FreeBSD source directory. This file was last revised on: $FreeBSD$ For copyright information, please see the file COPYRIGHT in this directory (additional copyright information also exists for some sources in this tree - please see the specific source directories for more information). The Makefile in this directory supports a number of targets for building components (or all) of the FreeBSD source tree, the most commonly used one being ``world'', which rebuilds and installs everything in the FreeBSD system from the source tree except the kernel, the kernel-modules and the contents of /etc. The ``world'' target should only be used in cases where the source tree has not changed from the currently running version. See: http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/makeworld.html for more information, including setting make(1) variables. The ``buildkernel'' and ``installkernel'' targets build and install the kernel and the modules (see below). Please see the top of the Makefile in this directory for more information on the standard build targets and compile-time flags. Building a kernel is a somewhat more involved process, documentation for which can be found at: http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/kernelconfig.html And in the config(8) man page. Note: If you want to build and install the kernel with the ``buildkernel'' and ``installkernel'' targets, you might need to build world before. More information is available in the handbook. The sample kernel configuration files reside in the sys/<arch>/conf sub-directory (assuming that you've installed the kernel sources), the file named GENERIC being the one used to build your initial installation kernel. The file NOTES contains entries and documentation for all possible devices, not just those commonly used. It is the successor of the ancient LINT file, but in contrast to LINT, it is not buildable as a kernel but a pure reference and documentation file. Source Roadmap: --------------- bin System/user commands. contrib Packages contributed by 3rd parties. crypto Cryptography stuff (see crypto/README). etc Template files for /etc. games Amusements. gnu Various commands and libraries under the GNU Public License. Please see gnu/COPYING* for more information. include System include files. kerberos5 Kerberos5 (Heimdal) package. lib System libraries. libexec System daemons. release Release building Makefile & associated tools. rescue Build system for statically linked /rescue utilities. sbin System commands. secure Cryptographic libraries and commands. share Shared resources. sys Kernel sources. tools Utilities for regression testing and miscellaneous tasks. usr.bin User commands. usr.sbin System administration commands. For information on synchronizing your source tree with one or more of the FreeBSD Project's development branches, please see: http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/synching.html