2907 lines
77 KiB
C
2907 lines
77 KiB
C
/*
|
|
* Copyright (c) 1997, 1998
|
|
* Bill Paul <wpaul@ctr.columbia.edu>. All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions
|
|
* are met:
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
* notice, this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright
|
|
* notice, this list of conditions and the following disclaimer in the
|
|
* documentation and/or other materials provided with the distribution.
|
|
* 3. All advertising materials mentioning features or use of this software
|
|
* must display the following acknowledgement:
|
|
* This product includes software developed by Bill Paul.
|
|
* 4. Neither the name of the author nor the names of any co-contributors
|
|
* may be used to endorse or promote products derived from this software
|
|
* without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND
|
|
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
|
|
* ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD
|
|
* BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
|
|
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
|
|
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
|
|
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
|
|
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
|
|
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
|
|
* THE POSSIBILITY OF SUCH DAMAGE.
|
|
*
|
|
* $Id: if_tl.c,v 1.34 1999/07/06 19:23:29 des Exp $
|
|
*/
|
|
|
|
/*
|
|
* Texas Instruments ThunderLAN driver for FreeBSD 2.2.6 and 3.x.
|
|
* Supports many Compaq PCI NICs based on the ThunderLAN ethernet controller,
|
|
* the National Semiconductor DP83840A physical interface and the
|
|
* Microchip Technology 24Cxx series serial EEPROM.
|
|
*
|
|
* Written using the following four documents:
|
|
*
|
|
* Texas Instruments ThunderLAN Programmer's Guide (www.ti.com)
|
|
* National Semiconductor DP83840A data sheet (www.national.com)
|
|
* Microchip Technology 24C02C data sheet (www.microchip.com)
|
|
* Micro Linear ML6692 100BaseTX only PHY data sheet (www.microlinear.com)
|
|
*
|
|
* Written by Bill Paul <wpaul@ctr.columbia.edu>
|
|
* Electrical Engineering Department
|
|
* Columbia University, New York City
|
|
*/
|
|
|
|
/*
|
|
* Some notes about the ThunderLAN:
|
|
*
|
|
* The ThunderLAN controller is a single chip containing PCI controller
|
|
* logic, approximately 3K of on-board SRAM, a LAN controller, and media
|
|
* independent interface (MII) bus. The MII allows the ThunderLAN chip to
|
|
* control up to 32 different physical interfaces (PHYs). The ThunderLAN
|
|
* also has a built-in 10baseT PHY, allowing a single ThunderLAN controller
|
|
* to act as a complete ethernet interface.
|
|
*
|
|
* Other PHYs may be attached to the ThunderLAN; the Compaq 10/100 cards
|
|
* use a National Semiconductor DP83840A PHY that supports 10 or 100Mb/sec
|
|
* in full or half duplex. Some of the Compaq Deskpro machines use a
|
|
* Level 1 LXT970 PHY with the same capabilities. Certain Olicom adapters
|
|
* use a Micro Linear ML6692 100BaseTX only PHY, which can be used in
|
|
* concert with the ThunderLAN's internal PHY to provide full 10/100
|
|
* support. This is cheaper than using a standalone external PHY for both
|
|
* 10/100 modes and letting the ThunderLAN's internal PHY go to waste.
|
|
* A serial EEPROM is also attached to the ThunderLAN chip to provide
|
|
* power-up default register settings and for storing the adapter's
|
|
* station address. Although not supported by this driver, the ThunderLAN
|
|
* chip can also be connected to token ring PHYs.
|
|
*
|
|
* The ThunderLAN has a set of registers which can be used to issue
|
|
* commands, acknowledge interrupts, and to manipulate other internal
|
|
* registers on its DIO bus. The primary registers can be accessed
|
|
* using either programmed I/O (inb/outb) or via PCI memory mapping,
|
|
* depending on how the card is configured during the PCI probing
|
|
* phase. It is even possible to have both PIO and memory mapped
|
|
* access turned on at the same time.
|
|
*
|
|
* Frame reception and transmission with the ThunderLAN chip is done
|
|
* using frame 'lists.' A list structure looks more or less like this:
|
|
*
|
|
* struct tl_frag {
|
|
* u_int32_t fragment_address;
|
|
* u_int32_t fragment_size;
|
|
* };
|
|
* struct tl_list {
|
|
* u_int32_t forward_pointer;
|
|
* u_int16_t cstat;
|
|
* u_int16_t frame_size;
|
|
* struct tl_frag fragments[10];
|
|
* };
|
|
*
|
|
* The forward pointer in the list header can be either a 0 or the address
|
|
* of another list, which allows several lists to be linked together. Each
|
|
* list contains up to 10 fragment descriptors. This means the chip allows
|
|
* ethernet frames to be broken up into up to 10 chunks for transfer to
|
|
* and from the SRAM. Note that the forward pointer and fragment buffer
|
|
* addresses are physical memory addresses, not virtual. Note also that
|
|
* a single ethernet frame can not span lists: if the host wants to
|
|
* transmit a frame and the frame data is split up over more than 10
|
|
* buffers, the frame has to collapsed before it can be transmitted.
|
|
*
|
|
* To receive frames, the driver sets up a number of lists and populates
|
|
* the fragment descriptors, then it sends an RX GO command to the chip.
|
|
* When a frame is received, the chip will DMA it into the memory regions
|
|
* specified by the fragment descriptors and then trigger an RX 'end of
|
|
* frame interrupt' when done. The driver may choose to use only one
|
|
* fragment per list; this may result is slighltly less efficient use
|
|
* of memory in exchange for improving performance.
|
|
*
|
|
* To transmit frames, the driver again sets up lists and fragment
|
|
* descriptors, only this time the buffers contain frame data that
|
|
* is to be DMA'ed into the chip instead of out of it. Once the chip
|
|
* has transfered the data into its on-board SRAM, it will trigger a
|
|
* TX 'end of frame' interrupt. It will also generate an 'end of channel'
|
|
* interrupt when it reaches the end of the list.
|
|
*/
|
|
|
|
/*
|
|
* Some notes about this driver:
|
|
*
|
|
* The ThunderLAN chip provides a couple of different ways to organize
|
|
* reception, transmission and interrupt handling. The simplest approach
|
|
* is to use one list each for transmission and reception. In this mode,
|
|
* the ThunderLAN will generate two interrupts for every received frame
|
|
* (one RX EOF and one RX EOC) and two for each transmitted frame (one
|
|
* TX EOF and one TX EOC). This may make the driver simpler but it hurts
|
|
* performance to have to handle so many interrupts.
|
|
*
|
|
* Initially I wanted to create a circular list of receive buffers so
|
|
* that the ThunderLAN chip would think there was an infinitely long
|
|
* receive channel and never deliver an RXEOC interrupt. However this
|
|
* doesn't work correctly under heavy load: while the manual says the
|
|
* chip will trigger an RXEOF interrupt each time a frame is copied into
|
|
* memory, you can't count on the chip waiting around for you to acknowledge
|
|
* the interrupt before it starts trying to DMA the next frame. The result
|
|
* is that the chip might traverse the entire circular list and then wrap
|
|
* around before you have a chance to do anything about it. Consequently,
|
|
* the receive list is terminated (with a 0 in the forward pointer in the
|
|
* last element). Each time an RXEOF interrupt arrives, the used list
|
|
* is shifted to the end of the list. This gives the appearance of an
|
|
* infinitely large RX chain so long as the driver doesn't fall behind
|
|
* the chip and allow all of the lists to be filled up.
|
|
*
|
|
* If all the lists are filled, the adapter will deliver an RX 'end of
|
|
* channel' interrupt when it hits the 0 forward pointer at the end of
|
|
* the chain. The RXEOC handler then cleans out the RX chain and resets
|
|
* the list head pointer in the ch_parm register and restarts the receiver.
|
|
*
|
|
* For frame transmission, it is possible to program the ThunderLAN's
|
|
* transmit interrupt threshold so that the chip can acknowledge multiple
|
|
* lists with only a single TX EOF interrupt. This allows the driver to
|
|
* queue several frames in one shot, and only have to handle a total
|
|
* two interrupts (one TX EOF and one TX EOC) no matter how many frames
|
|
* are transmitted. Frame transmission is done directly out of the
|
|
* mbufs passed to the tl_start() routine via the interface send queue.
|
|
* The driver simply sets up the fragment descriptors in the transmit
|
|
* lists to point to the mbuf data regions and sends a TX GO command.
|
|
*
|
|
* Note that since the RX and TX lists themselves are always used
|
|
* only by the driver, the are malloc()ed once at driver initialization
|
|
* time and never free()ed.
|
|
*
|
|
* Also, in order to remain as platform independent as possible, this
|
|
* driver uses memory mapped register access to manipulate the card
|
|
* as opposed to programmed I/O. This avoids the use of the inb/outb
|
|
* (and related) instructions which are specific to the i386 platform.
|
|
*
|
|
* Using these techniques, this driver achieves very high performance
|
|
* by minimizing the amount of interrupts generated during large
|
|
* transfers and by completely avoiding buffer copies. Frame transfer
|
|
* to and from the ThunderLAN chip is performed entirely by the chip
|
|
* itself thereby reducing the load on the host CPU.
|
|
*/
|
|
|
|
#include "bpf.h"
|
|
|
|
#include <sys/param.h>
|
|
#include <sys/systm.h>
|
|
#include <sys/sockio.h>
|
|
#include <sys/mbuf.h>
|
|
#include <sys/malloc.h>
|
|
#include <sys/kernel.h>
|
|
#include <sys/socket.h>
|
|
|
|
#include <net/if.h>
|
|
#include <net/if_arp.h>
|
|
#include <net/ethernet.h>
|
|
#include <net/if_dl.h>
|
|
#include <net/if_media.h>
|
|
|
|
#if NBPF > 0
|
|
#include <net/bpf.h>
|
|
#endif
|
|
|
|
#include <vm/vm.h> /* for vtophys */
|
|
#include <vm/pmap.h> /* for vtophys */
|
|
#include <machine/clock.h> /* for DELAY */
|
|
#include <machine/bus_memio.h>
|
|
#include <machine/bus_pio.h>
|
|
#include <machine/bus.h>
|
|
#include <machine/resource.h>
|
|
#include <sys/bus.h>
|
|
#include <sys/rman.h>
|
|
|
|
#include <pci/pcireg.h>
|
|
#include <pci/pcivar.h>
|
|
|
|
/*
|
|
* Default to using PIO register access mode to pacify certain
|
|
* laptop docking stations with built-in ThunderLAN chips that
|
|
* don't seem to handle memory mapped mode properly.
|
|
*/
|
|
#define TL_USEIOSPACE
|
|
|
|
/* #define TL_BACKGROUND_AUTONEG */
|
|
|
|
#include <pci/if_tlreg.h>
|
|
|
|
#if !defined(lint)
|
|
static const char rcsid[] =
|
|
"$Id: if_tl.c,v 1.34 1999/07/06 19:23:29 des Exp $";
|
|
#endif
|
|
|
|
/*
|
|
* Various supported device vendors/types and their names.
|
|
*/
|
|
|
|
static struct tl_type tl_devs[] = {
|
|
{ TI_VENDORID, TI_DEVICEID_THUNDERLAN,
|
|
"Texas Instruments ThunderLAN" },
|
|
{ COMPAQ_VENDORID, COMPAQ_DEVICEID_NETEL_10,
|
|
"Compaq Netelligent 10" },
|
|
{ COMPAQ_VENDORID, COMPAQ_DEVICEID_NETEL_10_100,
|
|
"Compaq Netelligent 10/100" },
|
|
{ COMPAQ_VENDORID, COMPAQ_DEVICEID_NETEL_10_100_PROLIANT,
|
|
"Compaq Netelligent 10/100 Proliant" },
|
|
{ COMPAQ_VENDORID, COMPAQ_DEVICEID_NETEL_10_100_DUAL,
|
|
"Compaq Netelligent 10/100 Dual Port" },
|
|
{ COMPAQ_VENDORID, COMPAQ_DEVICEID_NETFLEX_3P_INTEGRATED,
|
|
"Compaq NetFlex-3/P Integrated" },
|
|
{ COMPAQ_VENDORID, COMPAQ_DEVICEID_NETFLEX_3P,
|
|
"Compaq NetFlex-3/P" },
|
|
{ COMPAQ_VENDORID, COMPAQ_DEVICEID_NETFLEX_3P_BNC,
|
|
"Compaq NetFlex 3/P w/ BNC" },
|
|
{ COMPAQ_VENDORID, COMPAQ_DEVICEID_NETEL_10_100_EMBEDDED,
|
|
"Compaq Netelligent 10/100 TX Embedded UTP" },
|
|
{ COMPAQ_VENDORID, COMPAQ_DEVICEID_NETEL_10_T2_UTP_COAX,
|
|
"Compaq Netelligent 10 T/2 PCI UTP/Coax" },
|
|
{ COMPAQ_VENDORID, COMPAQ_DEVICEID_NETEL_10_100_TX_UTP,
|
|
"Compaq Netelligent 10/100 TX UTP" },
|
|
{ OLICOM_VENDORID, OLICOM_DEVICEID_OC2183,
|
|
"Olicom OC-2183/2185" },
|
|
{ OLICOM_VENDORID, OLICOM_DEVICEID_OC2325,
|
|
"Olicom OC-2325" },
|
|
{ OLICOM_VENDORID, OLICOM_DEVICEID_OC2326,
|
|
"Olicom OC-2326 10/100 TX UTP" },
|
|
{ 0, 0, NULL }
|
|
};
|
|
|
|
/*
|
|
* Various supported PHY vendors/types and their names. Note that
|
|
* this driver will work with pretty much any MII-compliant PHY,
|
|
* so failure to positively identify the chip is not a fatal error.
|
|
*/
|
|
|
|
static struct tl_type tl_phys[] = {
|
|
{ TI_PHY_VENDORID, TI_PHY_10BT, "<TI ThunderLAN 10BT (internal)>" },
|
|
{ TI_PHY_VENDORID, TI_PHY_100VGPMI, "<TI TNETE211 100VG Any-LAN>" },
|
|
{ NS_PHY_VENDORID, NS_PHY_83840A, "<National Semiconductor DP83840A>"},
|
|
{ LEVEL1_PHY_VENDORID, LEVEL1_PHY_LXT970, "<Level 1 LXT970>" },
|
|
{ INTEL_PHY_VENDORID, INTEL_PHY_82555, "<Intel 82555>" },
|
|
{ SEEQ_PHY_VENDORID, SEEQ_PHY_80220, "<SEEQ 80220>" },
|
|
{ 0, 0, "<MII-compliant physical interface>" }
|
|
};
|
|
|
|
static int tl_probe __P((device_t));
|
|
static int tl_attach __P((device_t));
|
|
static int tl_detach __P((device_t));
|
|
static int tl_attach_phy __P((struct tl_softc *));
|
|
static int tl_intvec_rxeoc __P((void *, u_int32_t));
|
|
static int tl_intvec_txeoc __P((void *, u_int32_t));
|
|
static int tl_intvec_txeof __P((void *, u_int32_t));
|
|
static int tl_intvec_rxeof __P((void *, u_int32_t));
|
|
static int tl_intvec_adchk __P((void *, u_int32_t));
|
|
static int tl_intvec_netsts __P((void *, u_int32_t));
|
|
|
|
static int tl_newbuf __P((struct tl_softc *,
|
|
struct tl_chain_onefrag *));
|
|
static void tl_stats_update __P((void *));
|
|
static int tl_encap __P((struct tl_softc *, struct tl_chain *,
|
|
struct mbuf *));
|
|
|
|
static void tl_intr __P((void *));
|
|
static void tl_start __P((struct ifnet *));
|
|
static int tl_ioctl __P((struct ifnet *, u_long, caddr_t));
|
|
static void tl_init __P((void *));
|
|
static void tl_stop __P((struct tl_softc *));
|
|
static void tl_watchdog __P((struct ifnet *));
|
|
static void tl_shutdown __P((device_t));
|
|
static int tl_ifmedia_upd __P((struct ifnet *));
|
|
static void tl_ifmedia_sts __P((struct ifnet *, struct ifmediareq *));
|
|
|
|
static u_int8_t tl_eeprom_putbyte __P((struct tl_softc *, int));
|
|
static u_int8_t tl_eeprom_getbyte __P((struct tl_softc *,
|
|
int, u_int8_t *));
|
|
static int tl_read_eeprom __P((struct tl_softc *, caddr_t, int, int));
|
|
|
|
static void tl_mii_sync __P((struct tl_softc *));
|
|
static void tl_mii_send __P((struct tl_softc *, u_int32_t, int));
|
|
static int tl_mii_readreg __P((struct tl_softc *, struct tl_mii_frame *));
|
|
static int tl_mii_writereg __P((struct tl_softc *, struct tl_mii_frame *));
|
|
static u_int16_t tl_phy_readreg __P((struct tl_softc *, int));
|
|
static void tl_phy_writereg __P((struct tl_softc *, int, int));
|
|
|
|
static void tl_autoneg __P((struct tl_softc *, int, int));
|
|
static void tl_setmode __P((struct tl_softc *, int));
|
|
static int tl_calchash __P((caddr_t));
|
|
static void tl_setmulti __P((struct tl_softc *));
|
|
static void tl_setfilt __P((struct tl_softc *, caddr_t, int));
|
|
static void tl_softreset __P((struct tl_softc *, int));
|
|
static void tl_hardreset __P((struct tl_softc *));
|
|
static int tl_list_rx_init __P((struct tl_softc *));
|
|
static int tl_list_tx_init __P((struct tl_softc *));
|
|
|
|
static u_int8_t tl_dio_read8 __P((struct tl_softc *, int));
|
|
static u_int16_t tl_dio_read16 __P((struct tl_softc *, int));
|
|
static u_int32_t tl_dio_read32 __P((struct tl_softc *, int));
|
|
static void tl_dio_write8 __P((struct tl_softc *, int, int));
|
|
static void tl_dio_write16 __P((struct tl_softc *, int, int));
|
|
static void tl_dio_write32 __P((struct tl_softc *, int, int));
|
|
static void tl_dio_setbit __P((struct tl_softc *, int, int));
|
|
static void tl_dio_clrbit __P((struct tl_softc *, int, int));
|
|
static void tl_dio_setbit16 __P((struct tl_softc *, int, int));
|
|
static void tl_dio_clrbit16 __P((struct tl_softc *, int, int));
|
|
|
|
#ifdef TL_USEIOSPACE
|
|
#define TL_RES SYS_RES_IOPORT
|
|
#define TL_RID TL_PCI_LOIO
|
|
#else
|
|
#define TL_RES SYS_RES_MEMORY
|
|
#define TL_RID TL_PCI_LOMEM
|
|
#endif
|
|
|
|
static device_method_t tl_methods[] = {
|
|
/* Device interface */
|
|
DEVMETHOD(device_probe, tl_probe),
|
|
DEVMETHOD(device_attach, tl_attach),
|
|
DEVMETHOD(device_detach, tl_detach),
|
|
DEVMETHOD(device_shutdown, tl_shutdown),
|
|
{ 0, 0 }
|
|
};
|
|
|
|
static driver_t tl_driver = {
|
|
"tl",
|
|
tl_methods,
|
|
sizeof(struct tl_softc)
|
|
};
|
|
|
|
static devclass_t tl_devclass;
|
|
|
|
DRIVER_MODULE(tl, pci, tl_driver, tl_devclass, 0, 0);
|
|
|
|
static u_int8_t tl_dio_read8(sc, reg)
|
|
struct tl_softc *sc;
|
|
int reg;
|
|
{
|
|
CSR_WRITE_2(sc, TL_DIO_ADDR, reg);
|
|
return(CSR_READ_1(sc, TL_DIO_DATA + (reg & 3)));
|
|
}
|
|
|
|
static u_int16_t tl_dio_read16(sc, reg)
|
|
struct tl_softc *sc;
|
|
int reg;
|
|
{
|
|
CSR_WRITE_2(sc, TL_DIO_ADDR, reg);
|
|
return(CSR_READ_2(sc, TL_DIO_DATA + (reg & 3)));
|
|
}
|
|
|
|
static u_int32_t tl_dio_read32(sc, reg)
|
|
struct tl_softc *sc;
|
|
int reg;
|
|
{
|
|
CSR_WRITE_2(sc, TL_DIO_ADDR, reg);
|
|
return(CSR_READ_4(sc, TL_DIO_DATA + (reg & 3)));
|
|
}
|
|
|
|
static void tl_dio_write8(sc, reg, val)
|
|
struct tl_softc *sc;
|
|
int reg;
|
|
int val;
|
|
{
|
|
CSR_WRITE_2(sc, TL_DIO_ADDR, reg);
|
|
CSR_WRITE_1(sc, TL_DIO_DATA + (reg & 3), val);
|
|
return;
|
|
}
|
|
|
|
static void tl_dio_write16(sc, reg, val)
|
|
struct tl_softc *sc;
|
|
int reg;
|
|
int val;
|
|
{
|
|
CSR_WRITE_2(sc, TL_DIO_ADDR, reg);
|
|
CSR_WRITE_2(sc, TL_DIO_DATA + (reg & 3), val);
|
|
return;
|
|
}
|
|
|
|
static void tl_dio_write32(sc, reg, val)
|
|
struct tl_softc *sc;
|
|
int reg;
|
|
int val;
|
|
{
|
|
CSR_WRITE_2(sc, TL_DIO_ADDR, reg);
|
|
CSR_WRITE_4(sc, TL_DIO_DATA + (reg & 3), val);
|
|
return;
|
|
}
|
|
|
|
static void tl_dio_setbit(sc, reg, bit)
|
|
struct tl_softc *sc;
|
|
int reg;
|
|
int bit;
|
|
{
|
|
u_int8_t f;
|
|
|
|
CSR_WRITE_2(sc, TL_DIO_ADDR, reg);
|
|
f = CSR_READ_1(sc, TL_DIO_DATA + (reg & 3));
|
|
f |= bit;
|
|
CSR_WRITE_1(sc, TL_DIO_DATA + (reg & 3), f);
|
|
|
|
return;
|
|
}
|
|
|
|
static void tl_dio_clrbit(sc, reg, bit)
|
|
struct tl_softc *sc;
|
|
int reg;
|
|
int bit;
|
|
{
|
|
u_int8_t f;
|
|
|
|
CSR_WRITE_2(sc, TL_DIO_ADDR, reg);
|
|
f = CSR_READ_1(sc, TL_DIO_DATA + (reg & 3));
|
|
f &= ~bit;
|
|
CSR_WRITE_1(sc, TL_DIO_DATA + (reg & 3), f);
|
|
|
|
return;
|
|
}
|
|
|
|
static void tl_dio_setbit16(sc, reg, bit)
|
|
struct tl_softc *sc;
|
|
int reg;
|
|
int bit;
|
|
{
|
|
u_int16_t f;
|
|
|
|
CSR_WRITE_2(sc, TL_DIO_ADDR, reg);
|
|
f = CSR_READ_2(sc, TL_DIO_DATA + (reg & 3));
|
|
f |= bit;
|
|
CSR_WRITE_2(sc, TL_DIO_DATA + (reg & 3), f);
|
|
|
|
return;
|
|
}
|
|
|
|
static void tl_dio_clrbit16(sc, reg, bit)
|
|
struct tl_softc *sc;
|
|
int reg;
|
|
int bit;
|
|
{
|
|
u_int16_t f;
|
|
|
|
CSR_WRITE_2(sc, TL_DIO_ADDR, reg);
|
|
f = CSR_READ_2(sc, TL_DIO_DATA + (reg & 3));
|
|
f &= ~bit;
|
|
CSR_WRITE_2(sc, TL_DIO_DATA + (reg & 3), f);
|
|
|
|
return;
|
|
}
|
|
|
|
/*
|
|
* Send an instruction or address to the EEPROM, check for ACK.
|
|
*/
|
|
static u_int8_t tl_eeprom_putbyte(sc, byte)
|
|
struct tl_softc *sc;
|
|
int byte;
|
|
{
|
|
register int i, ack = 0;
|
|
|
|
/*
|
|
* Make sure we're in TX mode.
|
|
*/
|
|
tl_dio_setbit(sc, TL_NETSIO, TL_SIO_ETXEN);
|
|
|
|
/*
|
|
* Feed in each bit and stobe the clock.
|
|
*/
|
|
for (i = 0x80; i; i >>= 1) {
|
|
if (byte & i) {
|
|
tl_dio_setbit(sc, TL_NETSIO, TL_SIO_EDATA);
|
|
} else {
|
|
tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_EDATA);
|
|
}
|
|
DELAY(1);
|
|
tl_dio_setbit(sc, TL_NETSIO, TL_SIO_ECLOK);
|
|
DELAY(1);
|
|
tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_ECLOK);
|
|
}
|
|
|
|
/*
|
|
* Turn off TX mode.
|
|
*/
|
|
tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_ETXEN);
|
|
|
|
/*
|
|
* Check for ack.
|
|
*/
|
|
tl_dio_setbit(sc, TL_NETSIO, TL_SIO_ECLOK);
|
|
ack = tl_dio_read8(sc, TL_NETSIO) & TL_SIO_EDATA;
|
|
tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_ECLOK);
|
|
|
|
return(ack);
|
|
}
|
|
|
|
/*
|
|
* Read a byte of data stored in the EEPROM at address 'addr.'
|
|
*/
|
|
static u_int8_t tl_eeprom_getbyte(sc, addr, dest)
|
|
struct tl_softc *sc;
|
|
int addr;
|
|
u_int8_t *dest;
|
|
{
|
|
register int i;
|
|
u_int8_t byte = 0;
|
|
|
|
tl_dio_write8(sc, TL_NETSIO, 0);
|
|
|
|
EEPROM_START;
|
|
|
|
/*
|
|
* Send write control code to EEPROM.
|
|
*/
|
|
if (tl_eeprom_putbyte(sc, EEPROM_CTL_WRITE)) {
|
|
printf("tl%d: failed to send write command, status: %x\n",
|
|
sc->tl_unit, tl_dio_read8(sc, TL_NETSIO));
|
|
return(1);
|
|
}
|
|
|
|
/*
|
|
* Send address of byte we want to read.
|
|
*/
|
|
if (tl_eeprom_putbyte(sc, addr)) {
|
|
printf("tl%d: failed to send address, status: %x\n",
|
|
sc->tl_unit, tl_dio_read8(sc, TL_NETSIO));
|
|
return(1);
|
|
}
|
|
|
|
EEPROM_STOP;
|
|
EEPROM_START;
|
|
/*
|
|
* Send read control code to EEPROM.
|
|
*/
|
|
if (tl_eeprom_putbyte(sc, EEPROM_CTL_READ)) {
|
|
printf("tl%d: failed to send write command, status: %x\n",
|
|
sc->tl_unit, tl_dio_read8(sc, TL_NETSIO));
|
|
return(1);
|
|
}
|
|
|
|
/*
|
|
* Start reading bits from EEPROM.
|
|
*/
|
|
tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_ETXEN);
|
|
for (i = 0x80; i; i >>= 1) {
|
|
tl_dio_setbit(sc, TL_NETSIO, TL_SIO_ECLOK);
|
|
DELAY(1);
|
|
if (tl_dio_read8(sc, TL_NETSIO) & TL_SIO_EDATA)
|
|
byte |= i;
|
|
tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_ECLOK);
|
|
DELAY(1);
|
|
}
|
|
|
|
EEPROM_STOP;
|
|
|
|
/*
|
|
* No ACK generated for read, so just return byte.
|
|
*/
|
|
|
|
*dest = byte;
|
|
|
|
return(0);
|
|
}
|
|
|
|
/*
|
|
* Read a sequence of bytes from the EEPROM.
|
|
*/
|
|
static int tl_read_eeprom(sc, dest, off, cnt)
|
|
struct tl_softc *sc;
|
|
caddr_t dest;
|
|
int off;
|
|
int cnt;
|
|
{
|
|
int err = 0, i;
|
|
u_int8_t byte = 0;
|
|
|
|
for (i = 0; i < cnt; i++) {
|
|
err = tl_eeprom_getbyte(sc, off + i, &byte);
|
|
if (err)
|
|
break;
|
|
*(dest + i) = byte;
|
|
}
|
|
|
|
return(err ? 1 : 0);
|
|
}
|
|
|
|
static void tl_mii_sync(sc)
|
|
struct tl_softc *sc;
|
|
{
|
|
register int i;
|
|
|
|
tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_MTXEN);
|
|
|
|
for (i = 0; i < 32; i++) {
|
|
tl_dio_setbit(sc, TL_NETSIO, TL_SIO_MCLK);
|
|
tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_MCLK);
|
|
}
|
|
|
|
return;
|
|
}
|
|
|
|
static void tl_mii_send(sc, bits, cnt)
|
|
struct tl_softc *sc;
|
|
u_int32_t bits;
|
|
int cnt;
|
|
{
|
|
int i;
|
|
|
|
for (i = (0x1 << (cnt - 1)); i; i >>= 1) {
|
|
tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_MCLK);
|
|
if (bits & i) {
|
|
tl_dio_setbit(sc, TL_NETSIO, TL_SIO_MDATA);
|
|
} else {
|
|
tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_MDATA);
|
|
}
|
|
tl_dio_setbit(sc, TL_NETSIO, TL_SIO_MCLK);
|
|
}
|
|
}
|
|
|
|
static int tl_mii_readreg(sc, frame)
|
|
struct tl_softc *sc;
|
|
struct tl_mii_frame *frame;
|
|
|
|
{
|
|
int i, ack, s;
|
|
int minten = 0;
|
|
|
|
s = splimp();
|
|
|
|
tl_mii_sync(sc);
|
|
|
|
/*
|
|
* Set up frame for RX.
|
|
*/
|
|
frame->mii_stdelim = TL_MII_STARTDELIM;
|
|
frame->mii_opcode = TL_MII_READOP;
|
|
frame->mii_turnaround = 0;
|
|
frame->mii_data = 0;
|
|
|
|
/*
|
|
* Turn off MII interrupt by forcing MINTEN low.
|
|
*/
|
|
minten = tl_dio_read8(sc, TL_NETSIO) & TL_SIO_MINTEN;
|
|
if (minten) {
|
|
tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_MINTEN);
|
|
}
|
|
|
|
/*
|
|
* Turn on data xmit.
|
|
*/
|
|
tl_dio_setbit(sc, TL_NETSIO, TL_SIO_MTXEN);
|
|
|
|
/*
|
|
* Send command/address info.
|
|
*/
|
|
tl_mii_send(sc, frame->mii_stdelim, 2);
|
|
tl_mii_send(sc, frame->mii_opcode, 2);
|
|
tl_mii_send(sc, frame->mii_phyaddr, 5);
|
|
tl_mii_send(sc, frame->mii_regaddr, 5);
|
|
|
|
/*
|
|
* Turn off xmit.
|
|
*/
|
|
tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_MTXEN);
|
|
|
|
/* Idle bit */
|
|
tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_MCLK);
|
|
tl_dio_setbit(sc, TL_NETSIO, TL_SIO_MCLK);
|
|
|
|
/* Check for ack */
|
|
tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_MCLK);
|
|
ack = tl_dio_read8(sc, TL_NETSIO) & TL_SIO_MDATA;
|
|
|
|
/* Complete the cycle */
|
|
tl_dio_setbit(sc, TL_NETSIO, TL_SIO_MCLK);
|
|
|
|
/*
|
|
* Now try reading data bits. If the ack failed, we still
|
|
* need to clock through 16 cycles to keep the PHYs in sync.
|
|
*/
|
|
if (ack) {
|
|
for(i = 0; i < 16; i++) {
|
|
tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_MCLK);
|
|
tl_dio_setbit(sc, TL_NETSIO, TL_SIO_MCLK);
|
|
}
|
|
goto fail;
|
|
}
|
|
|
|
for (i = 0x8000; i; i >>= 1) {
|
|
tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_MCLK);
|
|
if (!ack) {
|
|
if (tl_dio_read8(sc, TL_NETSIO) & TL_SIO_MDATA)
|
|
frame->mii_data |= i;
|
|
}
|
|
tl_dio_setbit(sc, TL_NETSIO, TL_SIO_MCLK);
|
|
}
|
|
|
|
fail:
|
|
|
|
tl_dio_setbit(sc, TL_NETSIO, TL_SIO_MCLK);
|
|
tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_MCLK);
|
|
|
|
/* Reenable interrupts */
|
|
if (minten) {
|
|
tl_dio_setbit(sc, TL_NETSIO, TL_SIO_MINTEN);
|
|
}
|
|
|
|
splx(s);
|
|
|
|
if (ack)
|
|
return(1);
|
|
return(0);
|
|
}
|
|
|
|
static int tl_mii_writereg(sc, frame)
|
|
struct tl_softc *sc;
|
|
struct tl_mii_frame *frame;
|
|
|
|
{
|
|
int s;
|
|
int minten;
|
|
|
|
tl_mii_sync(sc);
|
|
|
|
s = splimp();
|
|
/*
|
|
* Set up frame for TX.
|
|
*/
|
|
|
|
frame->mii_stdelim = TL_MII_STARTDELIM;
|
|
frame->mii_opcode = TL_MII_WRITEOP;
|
|
frame->mii_turnaround = TL_MII_TURNAROUND;
|
|
|
|
/*
|
|
* Turn off MII interrupt by forcing MINTEN low.
|
|
*/
|
|
minten = tl_dio_read8(sc, TL_NETSIO) & TL_SIO_MINTEN;
|
|
if (minten) {
|
|
tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_MINTEN);
|
|
}
|
|
|
|
/*
|
|
* Turn on data output.
|
|
*/
|
|
tl_dio_setbit(sc, TL_NETSIO, TL_SIO_MTXEN);
|
|
|
|
tl_mii_send(sc, frame->mii_stdelim, 2);
|
|
tl_mii_send(sc, frame->mii_opcode, 2);
|
|
tl_mii_send(sc, frame->mii_phyaddr, 5);
|
|
tl_mii_send(sc, frame->mii_regaddr, 5);
|
|
tl_mii_send(sc, frame->mii_turnaround, 2);
|
|
tl_mii_send(sc, frame->mii_data, 16);
|
|
|
|
tl_dio_setbit(sc, TL_NETSIO, TL_SIO_MCLK);
|
|
tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_MCLK);
|
|
|
|
/*
|
|
* Turn off xmit.
|
|
*/
|
|
tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_MTXEN);
|
|
|
|
/* Reenable interrupts */
|
|
if (minten)
|
|
tl_dio_setbit(sc, TL_NETSIO, TL_SIO_MINTEN);
|
|
|
|
splx(s);
|
|
|
|
return(0);
|
|
}
|
|
|
|
static u_int16_t tl_phy_readreg(sc, reg)
|
|
struct tl_softc *sc;
|
|
int reg;
|
|
{
|
|
struct tl_mii_frame frame;
|
|
|
|
bzero((char *)&frame, sizeof(frame));
|
|
|
|
frame.mii_phyaddr = sc->tl_phy_addr;
|
|
frame.mii_regaddr = reg;
|
|
tl_mii_readreg(sc, &frame);
|
|
|
|
/* Reenable MII interrupts, just in case. */
|
|
tl_dio_setbit(sc, TL_NETSIO, TL_SIO_MINTEN);
|
|
|
|
return(frame.mii_data);
|
|
}
|
|
|
|
static void tl_phy_writereg(sc, reg, data)
|
|
struct tl_softc *sc;
|
|
int reg;
|
|
int data;
|
|
{
|
|
struct tl_mii_frame frame;
|
|
|
|
bzero((char *)&frame, sizeof(frame));
|
|
|
|
frame.mii_phyaddr = sc->tl_phy_addr;
|
|
frame.mii_regaddr = reg;
|
|
frame.mii_data = data;
|
|
|
|
tl_mii_writereg(sc, &frame);
|
|
|
|
/* Reenable MII interrupts, just in case. */
|
|
tl_dio_setbit(sc, TL_NETSIO, TL_SIO_MINTEN);
|
|
|
|
return;
|
|
}
|
|
|
|
/*
|
|
* Initiate autonegotiation with a link partner.
|
|
*
|
|
* Note that the Texas Instruments ThunderLAN programmer's guide
|
|
* fails to mention one very important point about autonegotiation.
|
|
* Autonegotiation is done largely by the PHY, independent of the
|
|
* ThunderLAN chip itself: the PHY sets the flags in the BMCR
|
|
* register to indicate what modes were selected and if link status
|
|
* is good. In fact, the PHY does pretty much all of the work itself,
|
|
* except for one small detail.
|
|
*
|
|
* The PHY may negotiate a full-duplex of half-duplex link, and set
|
|
* the PHY_BMCR_DUPLEX bit accordingly, but the ThunderLAN's 'NetCommand'
|
|
* register _also_ has a half-duplex/full-duplex bit, and you MUST ALSO
|
|
* SET THIS BIT MANUALLY TO CORRESPOND TO THE MODE SELECTED FOR THE PHY!
|
|
* In other words, both the ThunderLAN chip and the PHY have to be
|
|
* programmed for full-duplex mode in order for full-duplex to actually
|
|
* work. So in order for autonegotiation to really work right, we have
|
|
* to wait for the link to come up, check the BMCR register, then set
|
|
* the ThunderLAN for full or half-duplex as needed.
|
|
*
|
|
* I struggled for two days to figure this out, so I'm making a point
|
|
* of drawing attention to this fact. I think it's very strange that
|
|
* the ThunderLAN doesn't automagically track the duplex state of the
|
|
* PHY, but there you have it.
|
|
*
|
|
* Also when, using a National Semiconductor DP83840A PHY, we have to
|
|
* allow a full three seconds for autonegotiation to complete. So what
|
|
* we do is flip the autonegotiation restart bit, then set a timeout
|
|
* to wake us up in three seconds to check the link state.
|
|
*
|
|
* Note that there are some versions of the Olicom 2326 that use a
|
|
* Micro Linear ML6692 100BaseTX PHY. This particular PHY is designed
|
|
* to provide 100BaseTX support only, but can be used with a controller
|
|
* that supports an internal 10Mbps PHY to provide a complete
|
|
* 10/100Mbps solution. However, the ML6692 does not have vendor and
|
|
* device ID registers, and hence always shows up with a vendor/device
|
|
* ID of 0.
|
|
*
|
|
* We detect this configuration by checking the phy vendor ID in the
|
|
* softc structure. If it's a zero, and we're negotiating a high-speed
|
|
* mode, then we turn off the internal PHY. If it's a zero and we've
|
|
* negotiated a high-speed mode, we turn on the internal PHY. Note
|
|
* that to make things even more fun, we have to make extra sure that
|
|
* the loopback bit in the internal PHY's control register is turned
|
|
* off.
|
|
*/
|
|
static void tl_autoneg(sc, flag, verbose)
|
|
struct tl_softc *sc;
|
|
int flag;
|
|
int verbose;
|
|
{
|
|
u_int16_t phy_sts = 0, media = 0, advert, ability;
|
|
struct ifnet *ifp;
|
|
struct ifmedia *ifm;
|
|
|
|
ifm = &sc->ifmedia;
|
|
ifp = &sc->arpcom.ac_if;
|
|
|
|
/*
|
|
* First, see if autoneg is supported. If not, there's
|
|
* no point in continuing.
|
|
*/
|
|
phy_sts = tl_phy_readreg(sc, PHY_BMSR);
|
|
if (!(phy_sts & PHY_BMSR_CANAUTONEG)) {
|
|
if (verbose)
|
|
printf("tl%d: autonegotiation not supported\n",
|
|
sc->tl_unit);
|
|
return;
|
|
}
|
|
|
|
switch (flag) {
|
|
case TL_FLAG_FORCEDELAY:
|
|
/*
|
|
* XXX Never use this option anywhere but in the probe
|
|
* routine: making the kernel stop dead in its tracks
|
|
* for three whole seconds after we've gone multi-user
|
|
* is really bad manners.
|
|
*/
|
|
tl_phy_writereg(sc, PHY_BMCR, PHY_BMCR_RESET);
|
|
DELAY(500);
|
|
phy_sts = tl_phy_readreg(sc, PHY_BMCR);
|
|
phy_sts |= PHY_BMCR_AUTONEGENBL|PHY_BMCR_AUTONEGRSTR;
|
|
tl_phy_writereg(sc, PHY_BMCR, phy_sts);
|
|
DELAY(5000000);
|
|
break;
|
|
case TL_FLAG_SCHEDDELAY:
|
|
/*
|
|
* Wait for the transmitter to go idle before starting
|
|
* an autoneg session, otherwise tl_start() may clobber
|
|
* our timeout, and we don't want to allow transmission
|
|
* during an autoneg session since that can screw it up.
|
|
*/
|
|
if (!sc->tl_txeoc) {
|
|
sc->tl_want_auto = 1;
|
|
return;
|
|
}
|
|
tl_phy_writereg(sc, PHY_BMCR, PHY_BMCR_RESET);
|
|
DELAY(500);
|
|
phy_sts = tl_phy_readreg(sc, PHY_BMCR);
|
|
phy_sts |= PHY_BMCR_AUTONEGENBL|PHY_BMCR_AUTONEGRSTR;
|
|
tl_phy_writereg(sc, PHY_BMCR, phy_sts);
|
|
ifp->if_timer = 5;
|
|
sc->tl_autoneg = 1;
|
|
sc->tl_want_auto = 0;
|
|
return;
|
|
case TL_FLAG_DELAYTIMEO:
|
|
ifp->if_timer = 0;
|
|
sc->tl_autoneg = 0;
|
|
break;
|
|
default:
|
|
printf("tl%d: invalid autoneg flag: %d\n", sc->tl_unit, flag);
|
|
return;
|
|
}
|
|
|
|
/*
|
|
* Read the BMSR register twice: the LINKSTAT bit is a
|
|
* latching bit.
|
|
*/
|
|
tl_phy_readreg(sc, PHY_BMSR);
|
|
phy_sts = tl_phy_readreg(sc, PHY_BMSR);
|
|
if (phy_sts & PHY_BMSR_AUTONEGCOMP) {
|
|
if (verbose)
|
|
printf("tl%d: autoneg complete, ", sc->tl_unit);
|
|
phy_sts = tl_phy_readreg(sc, PHY_BMSR);
|
|
} else {
|
|
if (verbose)
|
|
printf("tl%d: autoneg not complete, ", sc->tl_unit);
|
|
}
|
|
|
|
/* Link is good. Report modes and set duplex mode. */
|
|
if (phy_sts & PHY_BMSR_LINKSTAT) {
|
|
if (verbose)
|
|
printf("link status good ");
|
|
|
|
advert = tl_phy_readreg(sc, TL_PHY_ANAR);
|
|
ability = tl_phy_readreg(sc, TL_PHY_LPAR);
|
|
media = tl_phy_readreg(sc, PHY_BMCR);
|
|
|
|
/*
|
|
* Be sure to turn off the ISOLATE and
|
|
* LOOPBACK bits in the control register,
|
|
* otherwise we may not be able to communicate.
|
|
*/
|
|
media &= ~(PHY_BMCR_LOOPBK|PHY_BMCR_ISOLATE);
|
|
/* Set the DUPLEX bit in the NetCmd register accordingly. */
|
|
if (advert & PHY_ANAR_100BT4 && ability & PHY_ANAR_100BT4) {
|
|
ifm->ifm_media = IFM_ETHER|IFM_100_T4;
|
|
media |= PHY_BMCR_SPEEDSEL;
|
|
media &= ~PHY_BMCR_DUPLEX;
|
|
if (verbose)
|
|
printf("(100baseT4)\n");
|
|
} else if (advert & PHY_ANAR_100BTXFULL &&
|
|
ability & PHY_ANAR_100BTXFULL) {
|
|
ifm->ifm_media = IFM_ETHER|IFM_100_TX|IFM_FDX;
|
|
media |= PHY_BMCR_SPEEDSEL;
|
|
media |= PHY_BMCR_DUPLEX;
|
|
if (verbose)
|
|
printf("(full-duplex, 100Mbps)\n");
|
|
} else if (advert & PHY_ANAR_100BTXHALF &&
|
|
ability & PHY_ANAR_100BTXHALF) {
|
|
ifm->ifm_media = IFM_ETHER|IFM_100_TX|IFM_HDX;
|
|
media |= PHY_BMCR_SPEEDSEL;
|
|
media &= ~PHY_BMCR_DUPLEX;
|
|
if (verbose)
|
|
printf("(half-duplex, 100Mbps)\n");
|
|
} else if (advert & PHY_ANAR_10BTFULL &&
|
|
ability & PHY_ANAR_10BTFULL) {
|
|
ifm->ifm_media = IFM_ETHER|IFM_10_T|IFM_FDX;
|
|
media &= ~PHY_BMCR_SPEEDSEL;
|
|
media |= PHY_BMCR_DUPLEX;
|
|
if (verbose)
|
|
printf("(full-duplex, 10Mbps)\n");
|
|
} else {
|
|
ifm->ifm_media = IFM_ETHER|IFM_10_T|IFM_HDX;
|
|
media &= ~PHY_BMCR_SPEEDSEL;
|
|
media &= ~PHY_BMCR_DUPLEX;
|
|
if (verbose)
|
|
printf("(half-duplex, 10Mbps)\n");
|
|
}
|
|
|
|
if (media & PHY_BMCR_DUPLEX)
|
|
tl_dio_setbit(sc, TL_NETCMD, TL_CMD_DUPLEX);
|
|
else
|
|
tl_dio_clrbit(sc, TL_NETCMD, TL_CMD_DUPLEX);
|
|
|
|
media &= ~PHY_BMCR_AUTONEGENBL;
|
|
tl_phy_writereg(sc, PHY_BMCR, media);
|
|
} else {
|
|
if (verbose)
|
|
printf("no carrier\n");
|
|
}
|
|
|
|
tl_init(sc);
|
|
|
|
if (sc->tl_tx_pend) {
|
|
sc->tl_autoneg = 0;
|
|
sc->tl_tx_pend = 0;
|
|
tl_start(ifp);
|
|
}
|
|
|
|
return;
|
|
}
|
|
|
|
/*
|
|
* Set speed and duplex mode. Also program autoneg advertisements
|
|
* accordingly.
|
|
*/
|
|
static void tl_setmode(sc, media)
|
|
struct tl_softc *sc;
|
|
int media;
|
|
{
|
|
u_int16_t bmcr;
|
|
|
|
if (sc->tl_bitrate) {
|
|
if (IFM_SUBTYPE(media) == IFM_10_5)
|
|
tl_dio_setbit(sc, TL_ACOMMIT, TL_AC_MTXD1);
|
|
if (IFM_SUBTYPE(media) == IFM_10_T) {
|
|
tl_dio_clrbit(sc, TL_ACOMMIT, TL_AC_MTXD1);
|
|
if ((media & IFM_GMASK) == IFM_FDX) {
|
|
tl_dio_clrbit(sc, TL_ACOMMIT, TL_AC_MTXD3);
|
|
tl_dio_setbit(sc, TL_NETCMD, TL_CMD_DUPLEX);
|
|
} else {
|
|
tl_dio_setbit(sc, TL_ACOMMIT, TL_AC_MTXD3);
|
|
tl_dio_clrbit(sc, TL_NETCMD, TL_CMD_DUPLEX);
|
|
}
|
|
}
|
|
return;
|
|
}
|
|
|
|
bmcr = tl_phy_readreg(sc, PHY_BMCR);
|
|
|
|
bmcr &= ~(PHY_BMCR_SPEEDSEL|PHY_BMCR_DUPLEX|PHY_BMCR_AUTONEGENBL|
|
|
PHY_BMCR_LOOPBK|PHY_BMCR_ISOLATE);
|
|
|
|
if (IFM_SUBTYPE(media) == IFM_LOOP)
|
|
bmcr |= PHY_BMCR_LOOPBK;
|
|
|
|
if (IFM_SUBTYPE(media) == IFM_AUTO)
|
|
bmcr |= PHY_BMCR_AUTONEGENBL;
|
|
|
|
/*
|
|
* The ThunderLAN's internal PHY has an AUI transceiver
|
|
* that can be selected. This is usually attached to a
|
|
* 10base2/BNC port. In order to activate this port, we
|
|
* have to set the AUISEL bit in the internal PHY's
|
|
* special control register.
|
|
*/
|
|
if (IFM_SUBTYPE(media) == IFM_10_5) {
|
|
u_int16_t addr, ctl;
|
|
addr = sc->tl_phy_addr;
|
|
sc->tl_phy_addr = TL_PHYADDR_MAX;
|
|
ctl = tl_phy_readreg(sc, TL_PHY_CTL);
|
|
ctl |= PHY_CTL_AUISEL;
|
|
tl_phy_writereg(sc, TL_PHY_CTL, ctl);
|
|
tl_phy_writereg(sc, PHY_BMCR, bmcr);
|
|
sc->tl_phy_addr = addr;
|
|
bmcr |= PHY_BMCR_ISOLATE;
|
|
} else {
|
|
u_int16_t addr, ctl;
|
|
addr = sc->tl_phy_addr;
|
|
sc->tl_phy_addr = TL_PHYADDR_MAX;
|
|
ctl = tl_phy_readreg(sc, TL_PHY_CTL);
|
|
ctl &= ~PHY_CTL_AUISEL;
|
|
tl_phy_writereg(sc, TL_PHY_CTL, ctl);
|
|
tl_phy_writereg(sc, PHY_BMCR, PHY_BMCR_ISOLATE);
|
|
sc->tl_phy_addr = addr;
|
|
bmcr &= ~PHY_BMCR_ISOLATE;
|
|
}
|
|
|
|
if (IFM_SUBTYPE(media) == IFM_100_TX) {
|
|
bmcr |= PHY_BMCR_SPEEDSEL;
|
|
if ((media & IFM_GMASK) == IFM_FDX) {
|
|
bmcr |= PHY_BMCR_DUPLEX;
|
|
tl_dio_setbit(sc, TL_NETCMD, TL_CMD_DUPLEX);
|
|
} else {
|
|
bmcr &= ~PHY_BMCR_DUPLEX;
|
|
tl_dio_clrbit(sc, TL_NETCMD, TL_CMD_DUPLEX);
|
|
}
|
|
}
|
|
|
|
if (IFM_SUBTYPE(media) == IFM_10_T) {
|
|
bmcr &= ~PHY_BMCR_SPEEDSEL;
|
|
if ((media & IFM_GMASK) == IFM_FDX) {
|
|
bmcr |= PHY_BMCR_DUPLEX;
|
|
tl_dio_setbit(sc, TL_NETCMD, TL_CMD_DUPLEX);
|
|
} else {
|
|
bmcr &= ~PHY_BMCR_DUPLEX;
|
|
tl_dio_clrbit(sc, TL_NETCMD, TL_CMD_DUPLEX);
|
|
}
|
|
}
|
|
|
|
tl_phy_writereg(sc, PHY_BMCR, bmcr);
|
|
|
|
tl_init(sc);
|
|
|
|
return;
|
|
}
|
|
|
|
/*
|
|
* Calculate the hash of a MAC address for programming the multicast hash
|
|
* table. This hash is simply the address split into 6-bit chunks
|
|
* XOR'd, e.g.
|
|
* byte: 000000|00 1111|1111 22|222222|333333|33 4444|4444 55|555555
|
|
* bit: 765432|10 7654|3210 76|543210|765432|10 7654|3210 76|543210
|
|
* Bytes 0-2 and 3-5 are symmetrical, so are folded together. Then
|
|
* the folded 24-bit value is split into 6-bit portions and XOR'd.
|
|
*/
|
|
static int tl_calchash(addr)
|
|
caddr_t addr;
|
|
{
|
|
int t;
|
|
|
|
t = (addr[0] ^ addr[3]) << 16 | (addr[1] ^ addr[4]) << 8 |
|
|
(addr[2] ^ addr[5]);
|
|
return ((t >> 18) ^ (t >> 12) ^ (t >> 6) ^ t) & 0x3f;
|
|
}
|
|
|
|
/*
|
|
* The ThunderLAN has a perfect MAC address filter in addition to
|
|
* the multicast hash filter. The perfect filter can be programmed
|
|
* with up to four MAC addresses. The first one is always used to
|
|
* hold the station address, which leaves us free to use the other
|
|
* three for multicast addresses.
|
|
*/
|
|
static void tl_setfilt(sc, addr, slot)
|
|
struct tl_softc *sc;
|
|
caddr_t addr;
|
|
int slot;
|
|
{
|
|
int i;
|
|
u_int16_t regaddr;
|
|
|
|
regaddr = TL_AREG0_B5 + (slot * ETHER_ADDR_LEN);
|
|
|
|
for (i = 0; i < ETHER_ADDR_LEN; i++)
|
|
tl_dio_write8(sc, regaddr + i, *(addr + i));
|
|
|
|
return;
|
|
}
|
|
|
|
/*
|
|
* XXX In FreeBSD 3.0, multicast addresses are managed using a doubly
|
|
* linked list. This is fine, except addresses are added from the head
|
|
* end of the list. We want to arrange for 224.0.0.1 (the "all hosts")
|
|
* group to always be in the perfect filter, but as more groups are added,
|
|
* the 224.0.0.1 entry (which is always added first) gets pushed down
|
|
* the list and ends up at the tail. So after 3 or 4 multicast groups
|
|
* are added, the all-hosts entry gets pushed out of the perfect filter
|
|
* and into the hash table.
|
|
*
|
|
* Because the multicast list is a doubly-linked list as opposed to a
|
|
* circular queue, we don't have the ability to just grab the tail of
|
|
* the list and traverse it backwards. Instead, we have to traverse
|
|
* the list once to find the tail, then traverse it again backwards to
|
|
* update the multicast filter.
|
|
*/
|
|
static void tl_setmulti(sc)
|
|
struct tl_softc *sc;
|
|
{
|
|
struct ifnet *ifp;
|
|
u_int32_t hashes[2] = { 0, 0 };
|
|
int h, i;
|
|
struct ifmultiaddr *ifma;
|
|
u_int8_t dummy[] = { 0, 0, 0, 0, 0 ,0 };
|
|
ifp = &sc->arpcom.ac_if;
|
|
|
|
/* First, zot all the existing filters. */
|
|
for (i = 1; i < 4; i++)
|
|
tl_setfilt(sc, (caddr_t)&dummy, i);
|
|
tl_dio_write32(sc, TL_HASH1, 0);
|
|
tl_dio_write32(sc, TL_HASH2, 0);
|
|
|
|
/* Now program new ones. */
|
|
if (ifp->if_flags & IFF_ALLMULTI) {
|
|
hashes[0] = 0xFFFFFFFF;
|
|
hashes[1] = 0xFFFFFFFF;
|
|
} else {
|
|
i = 1;
|
|
/* First find the tail of the list. */
|
|
for (ifma = ifp->if_multiaddrs.lh_first; ifma != NULL;
|
|
ifma = ifma->ifma_link.le_next) {
|
|
if (ifma->ifma_link.le_next == NULL)
|
|
break;
|
|
}
|
|
/* Now traverse the list backwards. */
|
|
for (; ifma != NULL && ifma != (void *)&ifp->if_multiaddrs;
|
|
ifma = (struct ifmultiaddr *)ifma->ifma_link.le_prev) {
|
|
if (ifma->ifma_addr->sa_family != AF_LINK)
|
|
continue;
|
|
/*
|
|
* Program the first three multicast groups
|
|
* into the perfect filter. For all others,
|
|
* use the hash table.
|
|
*/
|
|
if (i < 4) {
|
|
tl_setfilt(sc,
|
|
LLADDR((struct sockaddr_dl *)ifma->ifma_addr), i);
|
|
i++;
|
|
continue;
|
|
}
|
|
|
|
h = tl_calchash(
|
|
LLADDR((struct sockaddr_dl *)ifma->ifma_addr));
|
|
if (h < 32)
|
|
hashes[0] |= (1 << h);
|
|
else
|
|
hashes[1] |= (1 << (h - 32));
|
|
}
|
|
}
|
|
|
|
tl_dio_write32(sc, TL_HASH1, hashes[0]);
|
|
tl_dio_write32(sc, TL_HASH2, hashes[1]);
|
|
|
|
return;
|
|
}
|
|
|
|
/*
|
|
* This routine is recommended by the ThunderLAN manual to insure that
|
|
* the internal PHY is powered up correctly. It also recommends a one
|
|
* second pause at the end to 'wait for the clocks to start' but in my
|
|
* experience this isn't necessary.
|
|
*/
|
|
static void tl_hardreset(sc)
|
|
struct tl_softc *sc;
|
|
{
|
|
int i;
|
|
u_int16_t old_addr, flags;
|
|
|
|
old_addr = sc->tl_phy_addr;
|
|
|
|
for (i = 0; i < TL_PHYADDR_MAX + 1; i++) {
|
|
sc->tl_phy_addr = i;
|
|
tl_mii_sync(sc);
|
|
}
|
|
|
|
flags = PHY_BMCR_LOOPBK|PHY_BMCR_ISOLATE|PHY_BMCR_PWRDOWN;
|
|
|
|
for (i = 0; i < TL_PHYADDR_MAX + 1; i++) {
|
|
sc->tl_phy_addr = i;
|
|
tl_phy_writereg(sc, PHY_BMCR, flags);
|
|
}
|
|
|
|
sc->tl_phy_addr = TL_PHYADDR_MAX;
|
|
tl_phy_writereg(sc, PHY_BMCR, PHY_BMCR_ISOLATE);
|
|
|
|
DELAY(50000);
|
|
|
|
tl_phy_writereg(sc, PHY_BMCR, PHY_BMCR_LOOPBK|PHY_BMCR_ISOLATE);
|
|
|
|
tl_mii_sync(sc);
|
|
|
|
while(tl_phy_readreg(sc, PHY_BMCR) & PHY_BMCR_RESET);
|
|
|
|
sc->tl_phy_addr = old_addr;
|
|
|
|
return;
|
|
}
|
|
|
|
static void tl_softreset(sc, internal)
|
|
struct tl_softc *sc;
|
|
int internal;
|
|
{
|
|
u_int32_t cmd, dummy, i;
|
|
|
|
/* Assert the adapter reset bit. */
|
|
CMD_SET(sc, TL_CMD_ADRST);
|
|
/* Turn off interrupts */
|
|
CMD_SET(sc, TL_CMD_INTSOFF);
|
|
|
|
/* First, clear the stats registers. */
|
|
for (i = 0; i < 5; i++)
|
|
dummy = tl_dio_read32(sc, TL_TXGOODFRAMES);
|
|
|
|
/* Clear Areg and Hash registers */
|
|
for (i = 0; i < 8; i++)
|
|
tl_dio_write32(sc, TL_AREG0_B5, 0x00000000);
|
|
|
|
/*
|
|
* Set up Netconfig register. Enable one channel and
|
|
* one fragment mode.
|
|
*/
|
|
tl_dio_setbit16(sc, TL_NETCONFIG, TL_CFG_ONECHAN|TL_CFG_ONEFRAG);
|
|
if (internal && !sc->tl_bitrate) {
|
|
tl_dio_setbit16(sc, TL_NETCONFIG, TL_CFG_PHYEN);
|
|
} else {
|
|
tl_dio_clrbit16(sc, TL_NETCONFIG, TL_CFG_PHYEN);
|
|
}
|
|
|
|
/* Handle cards with bitrate devices. */
|
|
if (sc->tl_bitrate)
|
|
tl_dio_setbit16(sc, TL_NETCONFIG, TL_CFG_BITRATE);
|
|
|
|
/* Set PCI burst size */
|
|
tl_dio_write8(sc, TL_BSIZEREG, 0x33);
|
|
|
|
/*
|
|
* Load adapter irq pacing timer and tx threshold.
|
|
* We make the transmit threshold 1 initially but we may
|
|
* change that later.
|
|
*/
|
|
cmd = CSR_READ_4(sc, TL_HOSTCMD);
|
|
cmd |= TL_CMD_NES;
|
|
cmd &= ~(TL_CMD_RT|TL_CMD_EOC|TL_CMD_ACK_MASK|TL_CMD_CHSEL_MASK);
|
|
CMD_PUT(sc, cmd | (TL_CMD_LDTHR | TX_THR));
|
|
CMD_PUT(sc, cmd | (TL_CMD_LDTMR | 0x00000003));
|
|
|
|
/* Unreset the MII */
|
|
tl_dio_setbit(sc, TL_NETSIO, TL_SIO_NMRST);
|
|
|
|
/* Clear status register */
|
|
tl_dio_setbit16(sc, TL_NETSTS, TL_STS_MIRQ);
|
|
tl_dio_setbit16(sc, TL_NETSTS, TL_STS_HBEAT);
|
|
tl_dio_setbit16(sc, TL_NETSTS, TL_STS_TXSTOP);
|
|
tl_dio_setbit16(sc, TL_NETSTS, TL_STS_RXSTOP);
|
|
|
|
/* Enable network status interrupts for everything. */
|
|
tl_dio_setbit(sc, TL_NETMASK, TL_MASK_MASK7|TL_MASK_MASK6|
|
|
TL_MASK_MASK5|TL_MASK_MASK4);
|
|
|
|
/* Take the adapter out of reset */
|
|
tl_dio_setbit(sc, TL_NETCMD, TL_CMD_NRESET|TL_CMD_NWRAP);
|
|
|
|
/* Wait for things to settle down a little. */
|
|
DELAY(500);
|
|
|
|
return;
|
|
}
|
|
|
|
/*
|
|
* Probe for a ThunderLAN chip. Check the PCI vendor and device IDs
|
|
* against our list and return its name if we find a match.
|
|
*/
|
|
static int tl_probe(dev)
|
|
device_t dev;
|
|
{
|
|
struct tl_type *t;
|
|
|
|
t = tl_devs;
|
|
|
|
while(t->tl_name != NULL) {
|
|
if ((pci_get_vendor(dev) == t->tl_vid) &&
|
|
(pci_get_device(dev) == t->tl_did)) {
|
|
device_set_desc(dev, t->tl_name);
|
|
return(0);
|
|
}
|
|
t++;
|
|
}
|
|
|
|
return(ENXIO);
|
|
}
|
|
|
|
/*
|
|
* Do the interface setup and attach for a PHY on a particular
|
|
* ThunderLAN chip. Also also set up interrupt vectors.
|
|
*/
|
|
static int tl_attach_phy(sc)
|
|
struct tl_softc *sc;
|
|
{
|
|
int phy_ctl;
|
|
struct tl_type *p = tl_phys;
|
|
int media = IFM_ETHER|IFM_100_TX|IFM_FDX;
|
|
struct ifnet *ifp;
|
|
|
|
ifp = &sc->arpcom.ac_if;
|
|
|
|
sc->tl_phy_did = tl_phy_readreg(sc, TL_PHY_DEVID);
|
|
sc->tl_phy_vid = tl_phy_readreg(sc, TL_PHY_VENID);
|
|
sc->tl_phy_sts = tl_phy_readreg(sc, TL_PHY_GENSTS);
|
|
phy_ctl = tl_phy_readreg(sc, TL_PHY_GENCTL);
|
|
|
|
/*
|
|
* PHY revision numbers tend to vary a bit. Our algorithm here
|
|
* is to check everything but the 8 least significant bits.
|
|
*/
|
|
while(p->tl_vid) {
|
|
if (sc->tl_phy_vid == p->tl_vid &&
|
|
(sc->tl_phy_did | 0x000F) == p->tl_did) {
|
|
sc->tl_pinfo = p;
|
|
break;
|
|
}
|
|
p++;
|
|
}
|
|
if (sc->tl_pinfo == NULL) {
|
|
sc->tl_pinfo = &tl_phys[PHY_UNKNOWN];
|
|
}
|
|
|
|
if (sc->tl_phy_sts & PHY_BMSR_100BT4 ||
|
|
sc->tl_phy_sts & PHY_BMSR_100BTXFULL ||
|
|
sc->tl_phy_sts & PHY_BMSR_100BTXHALF)
|
|
ifp->if_baudrate = 100000000;
|
|
else
|
|
ifp->if_baudrate = 10000000;
|
|
|
|
if (bootverbose) {
|
|
printf("tl%d: phy at mii address %d\n", sc->tl_unit,
|
|
sc->tl_phy_addr);
|
|
|
|
printf("tl%d: %s ", sc->tl_unit, sc->tl_pinfo->tl_name);
|
|
}
|
|
|
|
if (sc->tl_phy_sts & PHY_BMSR_100BT4 ||
|
|
sc->tl_phy_sts & PHY_BMSR_100BTXHALF ||
|
|
sc->tl_phy_sts & PHY_BMSR_100BTXHALF) {
|
|
if (bootverbose)
|
|
printf("10/100Mbps ");
|
|
} else {
|
|
media &= ~IFM_100_TX;
|
|
media |= IFM_10_T;
|
|
if (bootverbose)
|
|
printf("10Mbps ");
|
|
}
|
|
|
|
if (sc->tl_phy_sts & PHY_BMSR_100BTXFULL ||
|
|
sc->tl_phy_sts & PHY_BMSR_10BTFULL) {
|
|
if (bootverbose)
|
|
printf("full duplex ");
|
|
} else {
|
|
if (bootverbose)
|
|
printf("half duplex ");
|
|
media &= ~IFM_FDX;
|
|
}
|
|
|
|
if (sc->tl_phy_sts & PHY_BMSR_CANAUTONEG) {
|
|
media = IFM_ETHER|IFM_AUTO;
|
|
if (bootverbose)
|
|
printf("autonegotiating\n");
|
|
} else
|
|
if (bootverbose)
|
|
printf("\n");
|
|
|
|
/* If this isn't a known PHY, print the PHY indentifier info. */
|
|
if (sc->tl_pinfo->tl_vid == 0 && bootverbose)
|
|
printf("tl%d: vendor id: %04x product id: %04x\n",
|
|
sc->tl_unit, sc->tl_phy_vid, sc->tl_phy_did);
|
|
|
|
/* Set up ifmedia data and callbacks. */
|
|
ifmedia_init(&sc->ifmedia, 0, tl_ifmedia_upd, tl_ifmedia_sts);
|
|
|
|
/*
|
|
* All ThunderLANs support at least 10baseT half duplex.
|
|
* They also support AUI selection if used in 10Mb/s modes.
|
|
*/
|
|
ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_10_T|IFM_HDX, 0, NULL);
|
|
ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_10_T, 0, NULL);
|
|
ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_10_5, 0, NULL);
|
|
|
|
/* Some ThunderLAN PHYs support autonegotiation. */
|
|
if (sc->tl_phy_sts & PHY_BMSR_CANAUTONEG)
|
|
ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_AUTO, 0, NULL);
|
|
|
|
/* Some support 10baseT full duplex. */
|
|
if (sc->tl_phy_sts & PHY_BMSR_10BTFULL)
|
|
ifmedia_add(&sc->ifmedia,
|
|
IFM_ETHER|IFM_10_T|IFM_FDX, 0, NULL);
|
|
|
|
/* Some support 100BaseTX half duplex. */
|
|
if (sc->tl_phy_sts & PHY_BMSR_100BTXHALF)
|
|
ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_100_TX, 0, NULL);
|
|
if (sc->tl_phy_sts & PHY_BMSR_100BTXHALF)
|
|
ifmedia_add(&sc->ifmedia,
|
|
IFM_ETHER|IFM_100_TX|IFM_HDX, 0, NULL);
|
|
|
|
/* Some support 100BaseTX full duplex. */
|
|
if (sc->tl_phy_sts & PHY_BMSR_100BTXFULL)
|
|
ifmedia_add(&sc->ifmedia,
|
|
IFM_ETHER|IFM_100_TX|IFM_FDX, 0, NULL);
|
|
|
|
/* Some also support 100BaseT4. */
|
|
if (sc->tl_phy_sts & PHY_BMSR_100BT4)
|
|
ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_100_T4, 0, NULL);
|
|
|
|
/* Set default media. */
|
|
ifmedia_set(&sc->ifmedia, media);
|
|
|
|
/*
|
|
* Kick off an autonegotiation session if this PHY supports it.
|
|
* This is necessary to make sure the chip's duplex mode matches
|
|
* the PHY's duplex mode. It may not: once enabled, the PHY may
|
|
* autonegotiate full-duplex mode with its link partner, but the
|
|
* ThunderLAN chip defaults to half-duplex and stays there unless
|
|
* told otherwise.
|
|
*/
|
|
if (sc->tl_phy_sts & PHY_BMSR_CANAUTONEG) {
|
|
tl_init(sc);
|
|
#ifdef TL_BACKGROUND_AUTONEG
|
|
tl_autoneg(sc, TL_FLAG_SCHEDDELAY, 1);
|
|
#else
|
|
if (cold)
|
|
tl_autoneg(sc, TL_FLAG_FORCEDELAY, 1);
|
|
else
|
|
tl_autoneg(sc, TL_FLAG_SCHEDDELAY, 1);
|
|
#endif
|
|
}
|
|
|
|
return(0);
|
|
}
|
|
|
|
static int tl_attach(dev)
|
|
device_t dev;
|
|
{
|
|
int s, i, phys = 0;
|
|
u_int32_t command;
|
|
u_int16_t did, vid;
|
|
struct tl_type *t;
|
|
struct ifnet *ifp;
|
|
struct tl_softc *sc;
|
|
unsigned int round;
|
|
caddr_t roundptr;
|
|
int unit, error = 0, rid;
|
|
|
|
s = splimp();
|
|
|
|
vid = pci_get_vendor(dev);
|
|
did = pci_get_device(dev);
|
|
sc = device_get_softc(dev);
|
|
unit = device_get_unit(dev);
|
|
bzero(sc, sizeof(struct tl_softc));
|
|
|
|
t = tl_devs;
|
|
while(t->tl_name != NULL) {
|
|
if (vid == t->tl_vid && did == t->tl_did)
|
|
break;
|
|
t++;
|
|
}
|
|
|
|
if (t->tl_name == NULL) {
|
|
printf("tl%d: unknown device!?\n", unit);
|
|
goto fail;
|
|
}
|
|
|
|
/*
|
|
* Map control/status registers.
|
|
*/
|
|
command = pci_read_config(dev, PCI_COMMAND_STATUS_REG, 4);
|
|
command |= (PCIM_CMD_PORTEN|PCIM_CMD_MEMEN|PCIM_CMD_BUSMASTEREN);
|
|
pci_write_config(dev, PCI_COMMAND_STATUS_REG, command, 4);
|
|
command = pci_read_config(dev, PCI_COMMAND_STATUS_REG, 4);
|
|
|
|
#ifdef TL_USEIOSPACE
|
|
if (!(command & PCIM_CMD_PORTEN)) {
|
|
printf("tl%d: failed to enable I/O ports!\n", unit);
|
|
error = ENXIO;
|
|
goto fail;
|
|
}
|
|
|
|
rid = TL_PCI_LOIO;
|
|
sc->tl_res = bus_alloc_resource(dev, SYS_RES_IOPORT, &rid,
|
|
0, ~0, 1, RF_ACTIVE);
|
|
|
|
/*
|
|
* Some cards have the I/O and memory mapped address registers
|
|
* reversed. Try both combinations before giving up.
|
|
*/
|
|
if (sc->tl_res == NULL) {
|
|
rid = TL_PCI_LOMEM;
|
|
sc->tl_res = bus_alloc_resource(dev, SYS_RES_IOPORT, &rid,
|
|
0, ~0, 1, RF_ACTIVE);
|
|
}
|
|
#else
|
|
if (!(command & PCIM_CMD_MEMEN)) {
|
|
printf("tl%d: failed to enable memory mapping!\n", unit);
|
|
error = ENXIO;
|
|
goto fail;
|
|
}
|
|
|
|
rid = TL_PCI_LOMEM;
|
|
sc->tl_res = bus_alloc_resource(dev, SYS_RES_MEMORY, &rid,
|
|
0, ~0, 1, RF_ACTIVE);
|
|
if (sc->tl_res == NULL) {
|
|
rid = TL_PCI_LOIO;
|
|
sc->tl_res = bus_alloc_resource(dev, SYS_RES_MEMORY, &rid,
|
|
0, ~0, 1, RF_ACTIVE);
|
|
}
|
|
#endif
|
|
|
|
if (sc->tl_res == NULL) {
|
|
printf("tl%d: couldn't map ports/memory\n", unit);
|
|
error = ENXIO;
|
|
goto fail;
|
|
}
|
|
|
|
sc->tl_btag = rman_get_bustag(sc->tl_res);
|
|
sc->tl_bhandle = rman_get_bushandle(sc->tl_res);
|
|
|
|
#ifdef notdef
|
|
/*
|
|
* The ThunderLAN manual suggests jacking the PCI latency
|
|
* timer all the way up to its maximum value. I'm not sure
|
|
* if this is really necessary, but what the manual wants,
|
|
* the manual gets.
|
|
*/
|
|
command = pci_read_config(dev, TL_PCI_LATENCY_TIMER, 4);
|
|
command |= 0x0000FF00;
|
|
pci_write_config(dev, TL_PCI_LATENCY_TIMER, command, 4);
|
|
#endif
|
|
|
|
/* Allocate interrupt */
|
|
rid = 0;
|
|
sc->tl_irq = bus_alloc_resource(dev, SYS_RES_IRQ, &rid, 0, ~0, 1,
|
|
RF_SHAREABLE | RF_ACTIVE);
|
|
|
|
if (sc->tl_irq == NULL) {
|
|
bus_release_resource(dev, TL_RES, TL_RID, sc->tl_res);
|
|
printf("tl%d: couldn't map interrupt\n", unit);
|
|
error = ENXIO;
|
|
goto fail;
|
|
}
|
|
|
|
error = bus_setup_intr(dev, sc->tl_irq, INTR_TYPE_NET,
|
|
tl_intr, sc, &sc->tl_intrhand);
|
|
|
|
if (error) {
|
|
bus_release_resource(dev, SYS_RES_IRQ, 0, sc->tl_res);
|
|
bus_release_resource(dev, TL_RES, TL_RID, sc->tl_res);
|
|
printf("tl%d: couldn't set up irq\n", unit);
|
|
goto fail;
|
|
}
|
|
|
|
/*
|
|
* Now allocate memory for the TX and RX lists. Note that
|
|
* we actually allocate 8 bytes more than we really need:
|
|
* this is because we need to adjust the final address to
|
|
* be aligned on a quadword (64-bit) boundary in order to
|
|
* make the chip happy. If the list structures aren't properly
|
|
* aligned, DMA fails and the chip generates an adapter check
|
|
* interrupt and has to be reset. If you set up the softc struct
|
|
* just right you can sort of obtain proper alignment 'by chance.'
|
|
* But I don't want to depend on this, so instead the alignment
|
|
* is forced here.
|
|
*/
|
|
sc->tl_ldata_ptr = malloc(sizeof(struct tl_list_data) + 8,
|
|
M_DEVBUF, M_NOWAIT);
|
|
|
|
if (sc->tl_ldata_ptr == NULL) {
|
|
bus_teardown_intr(dev, sc->tl_irq, sc->tl_intrhand);
|
|
bus_release_resource(dev, SYS_RES_IRQ, 0, sc->tl_irq);
|
|
bus_release_resource(dev, TL_RES, TL_RID, sc->tl_res);
|
|
printf("tl%d: no memory for list buffers!\n", unit);
|
|
error = ENXIO;
|
|
goto fail;
|
|
}
|
|
|
|
/*
|
|
* Convoluted but satisfies my ANSI sensibilities. GCC lets
|
|
* you do casts on the LHS of an assignment, but ANSI doesn't
|
|
* allow that.
|
|
*/
|
|
sc->tl_ldata = (struct tl_list_data *)sc->tl_ldata_ptr;
|
|
round = (uintptr_t)sc->tl_ldata_ptr & 0xF;
|
|
roundptr = sc->tl_ldata_ptr;
|
|
for (i = 0; i < 8; i++) {
|
|
if (round % 8) {
|
|
round++;
|
|
roundptr++;
|
|
} else
|
|
break;
|
|
}
|
|
sc->tl_ldata = (struct tl_list_data *)roundptr;
|
|
|
|
bzero(sc->tl_ldata, sizeof(struct tl_list_data));
|
|
|
|
sc->tl_unit = unit;
|
|
sc->tl_dinfo = t;
|
|
if (t->tl_vid == COMPAQ_VENDORID || t->tl_vid == TI_VENDORID)
|
|
sc->tl_eeaddr = TL_EEPROM_EADDR;
|
|
if (t->tl_vid == OLICOM_VENDORID)
|
|
sc->tl_eeaddr = TL_EEPROM_EADDR_OC;
|
|
|
|
/* Reset the adapter. */
|
|
tl_softreset(sc, 1);
|
|
tl_hardreset(sc);
|
|
tl_softreset(sc, 1);
|
|
|
|
/*
|
|
* Get station address from the EEPROM.
|
|
*/
|
|
if (tl_read_eeprom(sc, (caddr_t)&sc->arpcom.ac_enaddr,
|
|
sc->tl_eeaddr, ETHER_ADDR_LEN)) {
|
|
bus_teardown_intr(dev, sc->tl_irq, sc->tl_intrhand);
|
|
bus_release_resource(dev, SYS_RES_IRQ, 0, sc->tl_irq);
|
|
bus_release_resource(dev, TL_RES, TL_RID, sc->tl_res);
|
|
free(sc->tl_ldata_ptr, M_DEVBUF);
|
|
printf("tl%d: failed to read station address\n", unit);
|
|
error = ENXIO;
|
|
goto fail;
|
|
}
|
|
|
|
/*
|
|
* XXX Olicom, in its desire to be different from the
|
|
* rest of the world, has done strange things with the
|
|
* encoding of the station address in the EEPROM. First
|
|
* of all, they store the address at offset 0xF8 rather
|
|
* than at 0x83 like the ThunderLAN manual suggests.
|
|
* Second, they store the address in three 16-bit words in
|
|
* network byte order, as opposed to storing it sequentially
|
|
* like all the other ThunderLAN cards. In order to get
|
|
* the station address in a form that matches what the Olicom
|
|
* diagnostic utility specifies, we have to byte-swap each
|
|
* word. To make things even more confusing, neither 00:00:28
|
|
* nor 00:00:24 appear in the IEEE OUI database.
|
|
*/
|
|
if (sc->tl_dinfo->tl_vid == OLICOM_VENDORID) {
|
|
for (i = 0; i < ETHER_ADDR_LEN; i += 2) {
|
|
u_int16_t *p;
|
|
p = (u_int16_t *)&sc->arpcom.ac_enaddr[i];
|
|
*p = ntohs(*p);
|
|
}
|
|
}
|
|
|
|
/*
|
|
* A ThunderLAN chip was detected. Inform the world.
|
|
*/
|
|
printf("tl%d: Ethernet address: %6D\n", unit,
|
|
sc->arpcom.ac_enaddr, ":");
|
|
|
|
ifp = &sc->arpcom.ac_if;
|
|
ifp->if_softc = sc;
|
|
ifp->if_unit = sc->tl_unit;
|
|
ifp->if_name = "tl";
|
|
ifp->if_flags = IFF_BROADCAST | IFF_SIMPLEX | IFF_MULTICAST;
|
|
ifp->if_ioctl = tl_ioctl;
|
|
ifp->if_output = ether_output;
|
|
ifp->if_start = tl_start;
|
|
ifp->if_watchdog = tl_watchdog;
|
|
ifp->if_init = tl_init;
|
|
ifp->if_mtu = ETHERMTU;
|
|
ifp->if_snd.ifq_maxlen = IFQ_MAXLEN;
|
|
callout_handle_init(&sc->tl_stat_ch);
|
|
|
|
/* Reset the adapter again. */
|
|
tl_softreset(sc, 1);
|
|
tl_hardreset(sc);
|
|
tl_softreset(sc, 1);
|
|
|
|
/*
|
|
* Now attach the ThunderLAN's PHYs. There will always
|
|
* be at least one PHY; if the PHY address is 0x1F, then
|
|
* it's the internal one.
|
|
*/
|
|
|
|
for (i = TL_PHYADDR_MIN; i < TL_PHYADDR_MAX + 1; i++) {
|
|
sc->tl_phy_addr = i;
|
|
if (bootverbose)
|
|
printf("tl%d: looking for phy at addr %x\n", unit, i);
|
|
tl_phy_writereg(sc, PHY_BMCR, PHY_BMCR_RESET);
|
|
DELAY(500);
|
|
while(tl_phy_readreg(sc, PHY_BMCR) & PHY_BMCR_RESET);
|
|
sc->tl_phy_sts = tl_phy_readreg(sc, PHY_BMSR);
|
|
if (bootverbose)
|
|
printf("tl%d: status: %x\n", unit, sc->tl_phy_sts);
|
|
if (!sc->tl_phy_sts)
|
|
continue;
|
|
if (tl_attach_phy(sc)) {
|
|
bus_teardown_intr(dev, sc->tl_irq, sc->tl_intrhand);
|
|
bus_release_resource(dev, SYS_RES_IRQ, 0, sc->tl_irq);
|
|
bus_release_resource(dev, TL_RES, TL_RID, sc->tl_res);
|
|
free(sc->tl_ldata_ptr, M_DEVBUF);
|
|
printf("tl%d: failed to attach a phy %d\n", unit, i);
|
|
error = ENXIO;
|
|
goto fail;
|
|
}
|
|
phys++;
|
|
if (phys && i != TL_PHYADDR_MAX)
|
|
break;
|
|
}
|
|
|
|
/*
|
|
* If no MII-based PHYs were detected, then this is a
|
|
* TNETE110 device with a bit rate PHY. There's no autoneg
|
|
* support, so just default to 10baseT mode.
|
|
*/
|
|
if (!phys) {
|
|
struct ifmedia *ifm;
|
|
sc->tl_bitrate = 1;
|
|
ifmedia_init(&sc->ifmedia, 0, tl_ifmedia_upd, tl_ifmedia_sts);
|
|
ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_10_T, 0, NULL);
|
|
ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_10_T|IFM_HDX, 0, NULL);
|
|
ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_10_T|IFM_FDX, 0, NULL);
|
|
ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_10_5, 0, NULL);
|
|
ifmedia_set(&sc->ifmedia, IFM_ETHER|IFM_10_T);
|
|
/* Reset again, this time setting bitrate mode. */
|
|
tl_softreset(sc, 1);
|
|
ifm = &sc->ifmedia;
|
|
ifm->ifm_media = ifm->ifm_cur->ifm_media;
|
|
tl_ifmedia_upd(ifp);
|
|
}
|
|
|
|
tl_intvec_adchk((void *)sc, 0);
|
|
tl_stop(sc);
|
|
|
|
/*
|
|
* Attempt to clear any stray interrupts
|
|
* that may be lurking.
|
|
*/
|
|
tl_intr((void *)sc);
|
|
|
|
/*
|
|
* Call MI attach routines.
|
|
*/
|
|
if_attach(ifp);
|
|
ether_ifattach(ifp);
|
|
|
|
#if NBPF > 0
|
|
bpfattach(ifp, DLT_EN10MB, sizeof(struct ether_header));
|
|
#endif
|
|
|
|
fail:
|
|
splx(s);
|
|
return(error);
|
|
}
|
|
|
|
static int tl_detach(dev)
|
|
device_t dev;
|
|
{
|
|
struct tl_softc *sc;
|
|
struct ifnet *ifp;
|
|
int s;
|
|
|
|
s = splimp();
|
|
|
|
sc = device_get_softc(dev);
|
|
ifp = &sc->arpcom.ac_if;
|
|
|
|
tl_stop(sc);
|
|
if_detach(ifp);
|
|
|
|
free(sc->tl_ldata_ptr, M_DEVBUF);
|
|
ifmedia_removeall(&sc->ifmedia);
|
|
|
|
bus_teardown_intr(dev, sc->tl_irq, sc->tl_intrhand);
|
|
bus_release_resource(dev, SYS_RES_IRQ, 0, sc->tl_irq);
|
|
bus_release_resource(dev, TL_RES, TL_RID, sc->tl_res);
|
|
|
|
splx(s);
|
|
|
|
return(0);
|
|
}
|
|
|
|
/*
|
|
* Initialize the transmit lists.
|
|
*/
|
|
static int tl_list_tx_init(sc)
|
|
struct tl_softc *sc;
|
|
{
|
|
struct tl_chain_data *cd;
|
|
struct tl_list_data *ld;
|
|
int i;
|
|
|
|
cd = &sc->tl_cdata;
|
|
ld = sc->tl_ldata;
|
|
for (i = 0; i < TL_TX_LIST_CNT; i++) {
|
|
cd->tl_tx_chain[i].tl_ptr = &ld->tl_tx_list[i];
|
|
if (i == (TL_TX_LIST_CNT - 1))
|
|
cd->tl_tx_chain[i].tl_next = NULL;
|
|
else
|
|
cd->tl_tx_chain[i].tl_next = &cd->tl_tx_chain[i + 1];
|
|
}
|
|
|
|
cd->tl_tx_free = &cd->tl_tx_chain[0];
|
|
cd->tl_tx_tail = cd->tl_tx_head = NULL;
|
|
sc->tl_txeoc = 1;
|
|
|
|
return(0);
|
|
}
|
|
|
|
/*
|
|
* Initialize the RX lists and allocate mbufs for them.
|
|
*/
|
|
static int tl_list_rx_init(sc)
|
|
struct tl_softc *sc;
|
|
{
|
|
struct tl_chain_data *cd;
|
|
struct tl_list_data *ld;
|
|
int i;
|
|
|
|
cd = &sc->tl_cdata;
|
|
ld = sc->tl_ldata;
|
|
|
|
for (i = 0; i < TL_RX_LIST_CNT; i++) {
|
|
cd->tl_rx_chain[i].tl_ptr =
|
|
(struct tl_list_onefrag *)&ld->tl_rx_list[i];
|
|
if (tl_newbuf(sc, &cd->tl_rx_chain[i]) == ENOBUFS)
|
|
return(ENOBUFS);
|
|
if (i == (TL_RX_LIST_CNT - 1)) {
|
|
cd->tl_rx_chain[i].tl_next = NULL;
|
|
ld->tl_rx_list[i].tlist_fptr = 0;
|
|
} else {
|
|
cd->tl_rx_chain[i].tl_next = &cd->tl_rx_chain[i + 1];
|
|
ld->tl_rx_list[i].tlist_fptr =
|
|
vtophys(&ld->tl_rx_list[i + 1]);
|
|
}
|
|
}
|
|
|
|
cd->tl_rx_head = &cd->tl_rx_chain[0];
|
|
cd->tl_rx_tail = &cd->tl_rx_chain[TL_RX_LIST_CNT - 1];
|
|
|
|
return(0);
|
|
}
|
|
|
|
static int tl_newbuf(sc, c)
|
|
struct tl_softc *sc;
|
|
struct tl_chain_onefrag *c;
|
|
{
|
|
struct mbuf *m_new = NULL;
|
|
|
|
MGETHDR(m_new, M_DONTWAIT, MT_DATA);
|
|
if (m_new == NULL) {
|
|
printf("tl%d: no memory for rx list -- packet dropped!",
|
|
sc->tl_unit);
|
|
return(ENOBUFS);
|
|
}
|
|
|
|
MCLGET(m_new, M_DONTWAIT);
|
|
if (!(m_new->m_flags & M_EXT)) {
|
|
printf("tl%d: no memory for rx list -- packet dropped!",
|
|
sc->tl_unit);
|
|
m_freem(m_new);
|
|
return(ENOBUFS);
|
|
}
|
|
|
|
#ifdef __alpha__
|
|
m_new->m_data += 2;
|
|
#endif
|
|
|
|
c->tl_mbuf = m_new;
|
|
c->tl_next = NULL;
|
|
c->tl_ptr->tlist_frsize = MCLBYTES;
|
|
c->tl_ptr->tlist_cstat = TL_CSTAT_READY;
|
|
c->tl_ptr->tlist_fptr = 0;
|
|
c->tl_ptr->tl_frag.tlist_dadr = vtophys(mtod(m_new, caddr_t));
|
|
c->tl_ptr->tl_frag.tlist_dcnt = MCLBYTES;
|
|
|
|
return(0);
|
|
}
|
|
/*
|
|
* Interrupt handler for RX 'end of frame' condition (EOF). This
|
|
* tells us that a full ethernet frame has been captured and we need
|
|
* to handle it.
|
|
*
|
|
* Reception is done using 'lists' which consist of a header and a
|
|
* series of 10 data count/data address pairs that point to buffers.
|
|
* Initially you're supposed to create a list, populate it with pointers
|
|
* to buffers, then load the physical address of the list into the
|
|
* ch_parm register. The adapter is then supposed to DMA the received
|
|
* frame into the buffers for you.
|
|
*
|
|
* To make things as fast as possible, we have the chip DMA directly
|
|
* into mbufs. This saves us from having to do a buffer copy: we can
|
|
* just hand the mbufs directly to ether_input(). Once the frame has
|
|
* been sent on its way, the 'list' structure is assigned a new buffer
|
|
* and moved to the end of the RX chain. As long we we stay ahead of
|
|
* the chip, it will always think it has an endless receive channel.
|
|
*
|
|
* If we happen to fall behind and the chip manages to fill up all of
|
|
* the buffers, it will generate an end of channel interrupt and wait
|
|
* for us to empty the chain and restart the receiver.
|
|
*/
|
|
static int tl_intvec_rxeof(xsc, type)
|
|
void *xsc;
|
|
u_int32_t type;
|
|
{
|
|
struct tl_softc *sc;
|
|
int r = 0, total_len = 0;
|
|
struct ether_header *eh;
|
|
struct mbuf *m;
|
|
struct ifnet *ifp;
|
|
struct tl_chain_onefrag *cur_rx;
|
|
|
|
sc = xsc;
|
|
ifp = &sc->arpcom.ac_if;
|
|
|
|
while(sc->tl_cdata.tl_rx_head->tl_ptr->tlist_cstat & TL_CSTAT_FRAMECMP){
|
|
r++;
|
|
cur_rx = sc->tl_cdata.tl_rx_head;
|
|
sc->tl_cdata.tl_rx_head = cur_rx->tl_next;
|
|
m = cur_rx->tl_mbuf;
|
|
total_len = cur_rx->tl_ptr->tlist_frsize;
|
|
|
|
if (tl_newbuf(sc, cur_rx) == ENOBUFS) {
|
|
ifp->if_ierrors++;
|
|
cur_rx->tl_ptr->tlist_frsize = MCLBYTES;
|
|
cur_rx->tl_ptr->tlist_cstat = TL_CSTAT_READY;
|
|
cur_rx->tl_ptr->tl_frag.tlist_dcnt = MCLBYTES;
|
|
continue;
|
|
}
|
|
|
|
sc->tl_cdata.tl_rx_tail->tl_ptr->tlist_fptr =
|
|
vtophys(cur_rx->tl_ptr);
|
|
sc->tl_cdata.tl_rx_tail->tl_next = cur_rx;
|
|
sc->tl_cdata.tl_rx_tail = cur_rx;
|
|
|
|
eh = mtod(m, struct ether_header *);
|
|
m->m_pkthdr.rcvif = ifp;
|
|
|
|
/*
|
|
* Note: when the ThunderLAN chip is in 'capture all
|
|
* frames' mode, it will receive its own transmissions.
|
|
* We drop don't need to process our own transmissions,
|
|
* so we drop them here and continue.
|
|
*/
|
|
/*if (ifp->if_flags & IFF_PROMISC && */
|
|
if (!bcmp(eh->ether_shost, sc->arpcom.ac_enaddr,
|
|
ETHER_ADDR_LEN)) {
|
|
m_freem(m);
|
|
continue;
|
|
}
|
|
|
|
#if NBPF > 0
|
|
/*
|
|
* Handle BPF listeners. Let the BPF user see the packet, but
|
|
* don't pass it up to the ether_input() layer unless it's
|
|
* a broadcast packet, multicast packet, matches our ethernet
|
|
* address or the interface is in promiscuous mode. If we don't
|
|
* want the packet, just forget it. We leave the mbuf in place
|
|
* since it can be used again later.
|
|
*/
|
|
if (ifp->if_bpf) {
|
|
m->m_pkthdr.len = m->m_len = total_len;
|
|
bpf_mtap(ifp, m);
|
|
if (ifp->if_flags & IFF_PROMISC &&
|
|
(bcmp(eh->ether_dhost, sc->arpcom.ac_enaddr,
|
|
ETHER_ADDR_LEN) &&
|
|
(eh->ether_dhost[0] & 1) == 0)) {
|
|
m_freem(m);
|
|
continue;
|
|
}
|
|
}
|
|
#endif
|
|
/* Remove header from mbuf and pass it on. */
|
|
m->m_pkthdr.len = m->m_len =
|
|
total_len - sizeof(struct ether_header);
|
|
m->m_data += sizeof(struct ether_header);
|
|
ether_input(ifp, eh, m);
|
|
}
|
|
|
|
return(r);
|
|
}
|
|
|
|
/*
|
|
* The RX-EOC condition hits when the ch_parm address hasn't been
|
|
* initialized or the adapter reached a list with a forward pointer
|
|
* of 0 (which indicates the end of the chain). In our case, this means
|
|
* the card has hit the end of the receive buffer chain and we need to
|
|
* empty out the buffers and shift the pointer back to the beginning again.
|
|
*/
|
|
static int tl_intvec_rxeoc(xsc, type)
|
|
void *xsc;
|
|
u_int32_t type;
|
|
{
|
|
struct tl_softc *sc;
|
|
int r;
|
|
|
|
sc = xsc;
|
|
|
|
/* Flush out the receive queue and ack RXEOF interrupts. */
|
|
r = tl_intvec_rxeof(xsc, type);
|
|
CMD_PUT(sc, TL_CMD_ACK | r | (type & ~(0x00100000)));
|
|
r = 1;
|
|
CSR_WRITE_4(sc, TL_CH_PARM, vtophys(sc->tl_cdata.tl_rx_head->tl_ptr));
|
|
r |= (TL_CMD_GO|TL_CMD_RT);
|
|
return(r);
|
|
}
|
|
|
|
static int tl_intvec_txeof(xsc, type)
|
|
void *xsc;
|
|
u_int32_t type;
|
|
{
|
|
struct tl_softc *sc;
|
|
int r = 0;
|
|
struct tl_chain *cur_tx;
|
|
|
|
sc = xsc;
|
|
|
|
/*
|
|
* Go through our tx list and free mbufs for those
|
|
* frames that have been sent.
|
|
*/
|
|
while (sc->tl_cdata.tl_tx_head != NULL) {
|
|
cur_tx = sc->tl_cdata.tl_tx_head;
|
|
if (!(cur_tx->tl_ptr->tlist_cstat & TL_CSTAT_FRAMECMP))
|
|
break;
|
|
sc->tl_cdata.tl_tx_head = cur_tx->tl_next;
|
|
|
|
r++;
|
|
m_freem(cur_tx->tl_mbuf);
|
|
cur_tx->tl_mbuf = NULL;
|
|
|
|
cur_tx->tl_next = sc->tl_cdata.tl_tx_free;
|
|
sc->tl_cdata.tl_tx_free = cur_tx;
|
|
if (!cur_tx->tl_ptr->tlist_fptr)
|
|
break;
|
|
}
|
|
|
|
return(r);
|
|
}
|
|
|
|
/*
|
|
* The transmit end of channel interrupt. The adapter triggers this
|
|
* interrupt to tell us it hit the end of the current transmit list.
|
|
*
|
|
* A note about this: it's possible for a condition to arise where
|
|
* tl_start() may try to send frames between TXEOF and TXEOC interrupts.
|
|
* You have to avoid this since the chip expects things to go in a
|
|
* particular order: transmit, acknowledge TXEOF, acknowledge TXEOC.
|
|
* When the TXEOF handler is called, it will free all of the transmitted
|
|
* frames and reset the tx_head pointer to NULL. However, a TXEOC
|
|
* interrupt should be received and acknowledged before any more frames
|
|
* are queued for transmission. If tl_statrt() is called after TXEOF
|
|
* resets the tx_head pointer but _before_ the TXEOC interrupt arrives,
|
|
* it could attempt to issue a transmit command prematurely.
|
|
*
|
|
* To guard against this, tl_start() will only issue transmit commands
|
|
* if the tl_txeoc flag is set, and only the TXEOC interrupt handler
|
|
* can set this flag once tl_start() has cleared it.
|
|
*/
|
|
static int tl_intvec_txeoc(xsc, type)
|
|
void *xsc;
|
|
u_int32_t type;
|
|
{
|
|
struct tl_softc *sc;
|
|
struct ifnet *ifp;
|
|
u_int32_t cmd;
|
|
|
|
sc = xsc;
|
|
ifp = &sc->arpcom.ac_if;
|
|
|
|
/* Clear the timeout timer. */
|
|
ifp->if_timer = 0;
|
|
|
|
if (sc->tl_cdata.tl_tx_head == NULL) {
|
|
ifp->if_flags &= ~IFF_OACTIVE;
|
|
sc->tl_cdata.tl_tx_tail = NULL;
|
|
sc->tl_txeoc = 1;
|
|
/*
|
|
* If we just drained the TX queue and
|
|
* there's an autoneg request waiting, set
|
|
* it in motion. This will block the transmitter
|
|
* until the autoneg session completes which will
|
|
* no doubt piss off any processes waiting to
|
|
* transmit, but that's the way the ball bounces.
|
|
*/
|
|
if (sc->tl_want_auto)
|
|
tl_autoneg(sc, TL_FLAG_SCHEDDELAY, 1);
|
|
} else {
|
|
sc->tl_txeoc = 0;
|
|
/* First we have to ack the EOC interrupt. */
|
|
CMD_PUT(sc, TL_CMD_ACK | 0x00000001 | type);
|
|
/* Then load the address of the next TX list. */
|
|
CSR_WRITE_4(sc, TL_CH_PARM,
|
|
vtophys(sc->tl_cdata.tl_tx_head->tl_ptr));
|
|
/* Restart TX channel. */
|
|
cmd = CSR_READ_4(sc, TL_HOSTCMD);
|
|
cmd &= ~TL_CMD_RT;
|
|
cmd |= TL_CMD_GO|TL_CMD_INTSON;
|
|
CMD_PUT(sc, cmd);
|
|
return(0);
|
|
}
|
|
|
|
return(1);
|
|
}
|
|
|
|
static int tl_intvec_adchk(xsc, type)
|
|
void *xsc;
|
|
u_int32_t type;
|
|
{
|
|
struct tl_softc *sc;
|
|
u_int16_t bmcr, ctl;
|
|
|
|
sc = xsc;
|
|
|
|
if (type)
|
|
printf("tl%d: adapter check: %x\n", sc->tl_unit,
|
|
(unsigned int)CSR_READ_4(sc, TL_CH_PARM));
|
|
|
|
/*
|
|
* Before resetting the adapter, try reading the PHY
|
|
* settings so we can put them back later. This is
|
|
* necessary to keep the chip operating at the same
|
|
* speed and duplex settings after the reset completes.
|
|
*/
|
|
if (!sc->tl_bitrate) {
|
|
bmcr = tl_phy_readreg(sc, PHY_BMCR);
|
|
ctl = tl_phy_readreg(sc, TL_PHY_CTL);
|
|
tl_softreset(sc, 1);
|
|
tl_phy_writereg(sc, PHY_BMCR, bmcr);
|
|
tl_phy_writereg(sc, TL_PHY_CTL, ctl);
|
|
if (bmcr & PHY_BMCR_DUPLEX) {
|
|
tl_dio_setbit(sc, TL_NETCMD, TL_CMD_DUPLEX);
|
|
} else {
|
|
tl_dio_clrbit(sc, TL_NETCMD, TL_CMD_DUPLEX);
|
|
}
|
|
}
|
|
tl_stop(sc);
|
|
tl_init(sc);
|
|
CMD_SET(sc, TL_CMD_INTSON);
|
|
|
|
return(0);
|
|
}
|
|
|
|
static int tl_intvec_netsts(xsc, type)
|
|
void *xsc;
|
|
u_int32_t type;
|
|
{
|
|
struct tl_softc *sc;
|
|
u_int16_t netsts;
|
|
|
|
sc = xsc;
|
|
|
|
netsts = tl_dio_read16(sc, TL_NETSTS);
|
|
tl_dio_write16(sc, TL_NETSTS, netsts);
|
|
|
|
printf("tl%d: network status: %x\n", sc->tl_unit, netsts);
|
|
|
|
return(1);
|
|
}
|
|
|
|
static void tl_intr(xsc)
|
|
void *xsc;
|
|
{
|
|
struct tl_softc *sc;
|
|
struct ifnet *ifp;
|
|
int r = 0;
|
|
u_int32_t type = 0;
|
|
u_int16_t ints = 0;
|
|
u_int8_t ivec = 0;
|
|
|
|
sc = xsc;
|
|
|
|
/* Disable interrupts */
|
|
ints = CSR_READ_2(sc, TL_HOST_INT);
|
|
CSR_WRITE_2(sc, TL_HOST_INT, ints);
|
|
type = (ints << 16) & 0xFFFF0000;
|
|
ivec = (ints & TL_VEC_MASK) >> 5;
|
|
ints = (ints & TL_INT_MASK) >> 2;
|
|
|
|
ifp = &sc->arpcom.ac_if;
|
|
|
|
switch(ints) {
|
|
case (TL_INTR_INVALID):
|
|
#ifdef DIAGNOSTIC
|
|
printf("tl%d: got an invalid interrupt!\n", sc->tl_unit);
|
|
#endif
|
|
/* Re-enable interrupts but don't ack this one. */
|
|
CMD_PUT(sc, type);
|
|
r = 0;
|
|
break;
|
|
case (TL_INTR_TXEOF):
|
|
r = tl_intvec_txeof((void *)sc, type);
|
|
break;
|
|
case (TL_INTR_TXEOC):
|
|
r = tl_intvec_txeoc((void *)sc, type);
|
|
break;
|
|
case (TL_INTR_STATOFLOW):
|
|
tl_stats_update(sc);
|
|
r = 1;
|
|
break;
|
|
case (TL_INTR_RXEOF):
|
|
r = tl_intvec_rxeof((void *)sc, type);
|
|
break;
|
|
case (TL_INTR_DUMMY):
|
|
printf("tl%d: got a dummy interrupt\n", sc->tl_unit);
|
|
r = 1;
|
|
break;
|
|
case (TL_INTR_ADCHK):
|
|
if (ivec)
|
|
r = tl_intvec_adchk((void *)sc, type);
|
|
else
|
|
r = tl_intvec_netsts((void *)sc, type);
|
|
break;
|
|
case (TL_INTR_RXEOC):
|
|
r = tl_intvec_rxeoc((void *)sc, type);
|
|
break;
|
|
default:
|
|
printf("tl%d: bogus interrupt type\n", ifp->if_unit);
|
|
break;
|
|
}
|
|
|
|
/* Re-enable interrupts */
|
|
if (r) {
|
|
CMD_PUT(sc, TL_CMD_ACK | r | type);
|
|
}
|
|
|
|
if (ifp->if_snd.ifq_head != NULL)
|
|
tl_start(ifp);
|
|
|
|
return;
|
|
}
|
|
|
|
static void tl_stats_update(xsc)
|
|
void *xsc;
|
|
{
|
|
struct tl_softc *sc;
|
|
struct ifnet *ifp;
|
|
struct tl_stats tl_stats;
|
|
u_int32_t *p;
|
|
int s;
|
|
|
|
s = splimp();
|
|
|
|
bzero((char *)&tl_stats, sizeof(struct tl_stats));
|
|
|
|
sc = xsc;
|
|
ifp = &sc->arpcom.ac_if;
|
|
|
|
p = (u_int32_t *)&tl_stats;
|
|
|
|
CSR_WRITE_2(sc, TL_DIO_ADDR, TL_TXGOODFRAMES|TL_DIO_ADDR_INC);
|
|
*p++ = CSR_READ_4(sc, TL_DIO_DATA);
|
|
*p++ = CSR_READ_4(sc, TL_DIO_DATA);
|
|
*p++ = CSR_READ_4(sc, TL_DIO_DATA);
|
|
*p++ = CSR_READ_4(sc, TL_DIO_DATA);
|
|
*p++ = CSR_READ_4(sc, TL_DIO_DATA);
|
|
|
|
ifp->if_opackets += tl_tx_goodframes(tl_stats);
|
|
ifp->if_collisions += tl_stats.tl_tx_single_collision +
|
|
tl_stats.tl_tx_multi_collision;
|
|
ifp->if_ipackets += tl_rx_goodframes(tl_stats);
|
|
ifp->if_ierrors += tl_stats.tl_crc_errors + tl_stats.tl_code_errors +
|
|
tl_rx_overrun(tl_stats);
|
|
ifp->if_oerrors += tl_tx_underrun(tl_stats);
|
|
|
|
sc->tl_stat_ch = timeout(tl_stats_update, sc, hz);
|
|
|
|
splx(s);
|
|
|
|
return;
|
|
}
|
|
|
|
/*
|
|
* Encapsulate an mbuf chain in a list by coupling the mbuf data
|
|
* pointers to the fragment pointers.
|
|
*/
|
|
static int tl_encap(sc, c, m_head)
|
|
struct tl_softc *sc;
|
|
struct tl_chain *c;
|
|
struct mbuf *m_head;
|
|
{
|
|
int frag = 0;
|
|
struct tl_frag *f = NULL;
|
|
int total_len;
|
|
struct mbuf *m;
|
|
|
|
/*
|
|
* Start packing the mbufs in this chain into
|
|
* the fragment pointers. Stop when we run out
|
|
* of fragments or hit the end of the mbuf chain.
|
|
*/
|
|
m = m_head;
|
|
total_len = 0;
|
|
|
|
for (m = m_head, frag = 0; m != NULL; m = m->m_next) {
|
|
if (m->m_len != 0) {
|
|
if (frag == TL_MAXFRAGS)
|
|
break;
|
|
total_len+= m->m_len;
|
|
c->tl_ptr->tl_frag[frag].tlist_dadr =
|
|
vtophys(mtod(m, vm_offset_t));
|
|
c->tl_ptr->tl_frag[frag].tlist_dcnt = m->m_len;
|
|
frag++;
|
|
}
|
|
}
|
|
|
|
/*
|
|
* Handle special cases.
|
|
* Special case #1: we used up all 10 fragments, but
|
|
* we have more mbufs left in the chain. Copy the
|
|
* data into an mbuf cluster. Note that we don't
|
|
* bother clearing the values in the other fragment
|
|
* pointers/counters; it wouldn't gain us anything,
|
|
* and would waste cycles.
|
|
*/
|
|
if (m != NULL) {
|
|
struct mbuf *m_new = NULL;
|
|
|
|
MGETHDR(m_new, M_DONTWAIT, MT_DATA);
|
|
if (m_new == NULL) {
|
|
printf("tl%d: no memory for tx list", sc->tl_unit);
|
|
return(1);
|
|
}
|
|
if (m_head->m_pkthdr.len > MHLEN) {
|
|
MCLGET(m_new, M_DONTWAIT);
|
|
if (!(m_new->m_flags & M_EXT)) {
|
|
m_freem(m_new);
|
|
printf("tl%d: no memory for tx list",
|
|
sc->tl_unit);
|
|
return(1);
|
|
}
|
|
}
|
|
m_copydata(m_head, 0, m_head->m_pkthdr.len,
|
|
mtod(m_new, caddr_t));
|
|
m_new->m_pkthdr.len = m_new->m_len = m_head->m_pkthdr.len;
|
|
m_freem(m_head);
|
|
m_head = m_new;
|
|
f = &c->tl_ptr->tl_frag[0];
|
|
f->tlist_dadr = vtophys(mtod(m_new, caddr_t));
|
|
f->tlist_dcnt = total_len = m_new->m_len;
|
|
frag = 1;
|
|
}
|
|
|
|
/*
|
|
* Special case #2: the frame is smaller than the minimum
|
|
* frame size. We have to pad it to make the chip happy.
|
|
*/
|
|
if (total_len < TL_MIN_FRAMELEN) {
|
|
if (frag == TL_MAXFRAGS)
|
|
printf("tl%d: all frags filled but "
|
|
"frame still to small!\n", sc->tl_unit);
|
|
f = &c->tl_ptr->tl_frag[frag];
|
|
f->tlist_dcnt = TL_MIN_FRAMELEN - total_len;
|
|
f->tlist_dadr = vtophys(&sc->tl_ldata->tl_pad);
|
|
total_len += f->tlist_dcnt;
|
|
frag++;
|
|
}
|
|
|
|
c->tl_mbuf = m_head;
|
|
c->tl_ptr->tl_frag[frag - 1].tlist_dcnt |= TL_LAST_FRAG;
|
|
c->tl_ptr->tlist_frsize = total_len;
|
|
c->tl_ptr->tlist_cstat = TL_CSTAT_READY;
|
|
c->tl_ptr->tlist_fptr = 0;
|
|
|
|
return(0);
|
|
}
|
|
|
|
/*
|
|
* Main transmit routine. To avoid having to do mbuf copies, we put pointers
|
|
* to the mbuf data regions directly in the transmit lists. We also save a
|
|
* copy of the pointers since the transmit list fragment pointers are
|
|
* physical addresses.
|
|
*/
|
|
static void tl_start(ifp)
|
|
struct ifnet *ifp;
|
|
{
|
|
struct tl_softc *sc;
|
|
struct mbuf *m_head = NULL;
|
|
u_int32_t cmd;
|
|
struct tl_chain *prev = NULL, *cur_tx = NULL, *start_tx;
|
|
|
|
sc = ifp->if_softc;
|
|
|
|
if (sc->tl_autoneg) {
|
|
sc->tl_tx_pend = 1;
|
|
return;
|
|
}
|
|
|
|
/*
|
|
* Check for an available queue slot. If there are none,
|
|
* punt.
|
|
*/
|
|
if (sc->tl_cdata.tl_tx_free == NULL) {
|
|
ifp->if_flags |= IFF_OACTIVE;
|
|
return;
|
|
}
|
|
|
|
start_tx = sc->tl_cdata.tl_tx_free;
|
|
|
|
while(sc->tl_cdata.tl_tx_free != NULL) {
|
|
IF_DEQUEUE(&ifp->if_snd, m_head);
|
|
if (m_head == NULL)
|
|
break;
|
|
|
|
/* Pick a chain member off the free list. */
|
|
cur_tx = sc->tl_cdata.tl_tx_free;
|
|
sc->tl_cdata.tl_tx_free = cur_tx->tl_next;
|
|
|
|
cur_tx->tl_next = NULL;
|
|
|
|
/* Pack the data into the list. */
|
|
tl_encap(sc, cur_tx, m_head);
|
|
|
|
/* Chain it together */
|
|
if (prev != NULL) {
|
|
prev->tl_next = cur_tx;
|
|
prev->tl_ptr->tlist_fptr = vtophys(cur_tx->tl_ptr);
|
|
}
|
|
prev = cur_tx;
|
|
|
|
/*
|
|
* If there's a BPF listener, bounce a copy of this frame
|
|
* to him.
|
|
*/
|
|
#if NBPF > 0
|
|
if (ifp->if_bpf)
|
|
bpf_mtap(ifp, cur_tx->tl_mbuf);
|
|
#endif
|
|
}
|
|
|
|
/*
|
|
* If there are no packets queued, bail.
|
|
*/
|
|
if (cur_tx == NULL)
|
|
return;
|
|
|
|
/*
|
|
* That's all we can stands, we can't stands no more.
|
|
* If there are no other transfers pending, then issue the
|
|
* TX GO command to the adapter to start things moving.
|
|
* Otherwise, just leave the data in the queue and let
|
|
* the EOF/EOC interrupt handler send.
|
|
*/
|
|
if (sc->tl_cdata.tl_tx_head == NULL) {
|
|
sc->tl_cdata.tl_tx_head = start_tx;
|
|
sc->tl_cdata.tl_tx_tail = cur_tx;
|
|
|
|
if (sc->tl_txeoc) {
|
|
sc->tl_txeoc = 0;
|
|
CSR_WRITE_4(sc, TL_CH_PARM, vtophys(start_tx->tl_ptr));
|
|
cmd = CSR_READ_4(sc, TL_HOSTCMD);
|
|
cmd &= ~TL_CMD_RT;
|
|
cmd |= TL_CMD_GO|TL_CMD_INTSON;
|
|
CMD_PUT(sc, cmd);
|
|
}
|
|
} else {
|
|
sc->tl_cdata.tl_tx_tail->tl_next = start_tx;
|
|
sc->tl_cdata.tl_tx_tail = cur_tx;
|
|
}
|
|
|
|
/*
|
|
* Set a timeout in case the chip goes out to lunch.
|
|
*/
|
|
ifp->if_timer = 5;
|
|
|
|
return;
|
|
}
|
|
|
|
static void tl_init(xsc)
|
|
void *xsc;
|
|
{
|
|
struct tl_softc *sc = xsc;
|
|
struct ifnet *ifp = &sc->arpcom.ac_if;
|
|
int s;
|
|
u_int16_t phy_sts;
|
|
|
|
if (sc->tl_autoneg)
|
|
return;
|
|
|
|
s = splimp();
|
|
|
|
ifp = &sc->arpcom.ac_if;
|
|
|
|
/*
|
|
* Cancel pending I/O.
|
|
*/
|
|
tl_stop(sc);
|
|
|
|
/*
|
|
* Set 'capture all frames' bit for promiscuous mode.
|
|
*/
|
|
if (ifp->if_flags & IFF_PROMISC)
|
|
tl_dio_setbit(sc, TL_NETCMD, TL_CMD_CAF);
|
|
else
|
|
tl_dio_clrbit(sc, TL_NETCMD, TL_CMD_CAF);
|
|
|
|
/*
|
|
* Set capture broadcast bit to capture broadcast frames.
|
|
*/
|
|
if (ifp->if_flags & IFF_BROADCAST)
|
|
tl_dio_clrbit(sc, TL_NETCMD, TL_CMD_NOBRX);
|
|
else
|
|
tl_dio_setbit(sc, TL_NETCMD, TL_CMD_NOBRX);
|
|
|
|
/* Init our MAC address */
|
|
tl_setfilt(sc, (caddr_t)&sc->arpcom.ac_enaddr, 0);
|
|
|
|
/* Init multicast filter, if needed. */
|
|
tl_setmulti(sc);
|
|
|
|
/* Init circular RX list. */
|
|
if (tl_list_rx_init(sc) == ENOBUFS) {
|
|
printf("tl%d: initialization failed: no "
|
|
"memory for rx buffers\n", sc->tl_unit);
|
|
tl_stop(sc);
|
|
return;
|
|
}
|
|
|
|
/* Init TX pointers. */
|
|
tl_list_tx_init(sc);
|
|
|
|
/*
|
|
* Enable PHY interrupts.
|
|
*/
|
|
phy_sts = tl_phy_readreg(sc, TL_PHY_CTL);
|
|
phy_sts |= PHY_CTL_INTEN;
|
|
tl_phy_writereg(sc, TL_PHY_CTL, phy_sts);
|
|
|
|
/* Enable MII interrupts. */
|
|
tl_dio_setbit(sc, TL_NETSIO, TL_SIO_MINTEN);
|
|
|
|
/* Enable PCI interrupts. */
|
|
CMD_SET(sc, TL_CMD_INTSON);
|
|
|
|
/* Load the address of the rx list */
|
|
CMD_SET(sc, TL_CMD_RT);
|
|
CSR_WRITE_4(sc, TL_CH_PARM, vtophys(&sc->tl_ldata->tl_rx_list[0]));
|
|
|
|
/*
|
|
* XXX This is a kludge to handle adapters with the Micro Linear
|
|
* ML6692 100BaseTX PHY, which only supports 100Mbps modes and
|
|
* relies on the controller's internal 10Mbps PHY to provide
|
|
* 10Mbps modes. The ML6692 always shows up with a vendor/device ID
|
|
* of 0 (it doesn't actually have vendor/device ID registers)
|
|
* so we use that property to detect it. In theory there ought to
|
|
* be a better way to 'spot the looney' but I can't find one.
|
|
*/
|
|
if (!sc->tl_phy_vid) {
|
|
u_int8_t addr = 0;
|
|
u_int16_t bmcr;
|
|
|
|
bmcr = tl_phy_readreg(sc, PHY_BMCR);
|
|
addr = sc->tl_phy_addr;
|
|
sc->tl_phy_addr = TL_PHYADDR_MAX;
|
|
tl_phy_writereg(sc, PHY_BMCR, PHY_BMCR_RESET);
|
|
if (bmcr & PHY_BMCR_SPEEDSEL)
|
|
tl_phy_writereg(sc, PHY_BMCR, PHY_BMCR_ISOLATE);
|
|
else
|
|
tl_phy_writereg(sc, PHY_BMCR, bmcr);
|
|
sc->tl_phy_addr = addr;
|
|
}
|
|
|
|
/* Send the RX go command */
|
|
CMD_SET(sc, TL_CMD_GO|TL_CMD_RT);
|
|
|
|
ifp->if_flags |= IFF_RUNNING;
|
|
ifp->if_flags &= ~IFF_OACTIVE;
|
|
|
|
(void)splx(s);
|
|
|
|
/* Start the stats update counter */
|
|
sc->tl_stat_ch = timeout(tl_stats_update, sc, hz);
|
|
|
|
return;
|
|
}
|
|
|
|
/*
|
|
* Set media options.
|
|
*/
|
|
static int tl_ifmedia_upd(ifp)
|
|
struct ifnet *ifp;
|
|
{
|
|
struct tl_softc *sc;
|
|
struct ifmedia *ifm;
|
|
|
|
sc = ifp->if_softc;
|
|
ifm = &sc->ifmedia;
|
|
|
|
if (IFM_TYPE(ifm->ifm_media) != IFM_ETHER)
|
|
return(EINVAL);
|
|
|
|
if (IFM_SUBTYPE(ifm->ifm_media) == IFM_AUTO)
|
|
tl_autoneg(sc, TL_FLAG_SCHEDDELAY, 1);
|
|
else
|
|
tl_setmode(sc, ifm->ifm_media);
|
|
|
|
return(0);
|
|
}
|
|
|
|
/*
|
|
* Report current media status.
|
|
*/
|
|
static void tl_ifmedia_sts(ifp, ifmr)
|
|
struct ifnet *ifp;
|
|
struct ifmediareq *ifmr;
|
|
{
|
|
u_int16_t phy_ctl;
|
|
u_int16_t phy_sts;
|
|
struct tl_softc *sc;
|
|
|
|
sc = ifp->if_softc;
|
|
|
|
ifmr->ifm_active = IFM_ETHER;
|
|
|
|
if (sc->tl_bitrate) {
|
|
if (tl_dio_read8(sc, TL_ACOMMIT) & TL_AC_MTXD1)
|
|
ifmr->ifm_active = IFM_ETHER|IFM_10_5;
|
|
else
|
|
ifmr->ifm_active = IFM_ETHER|IFM_10_T;
|
|
if (tl_dio_read8(sc, TL_ACOMMIT) & TL_AC_MTXD3)
|
|
ifmr->ifm_active |= IFM_HDX;
|
|
else
|
|
ifmr->ifm_active |= IFM_FDX;
|
|
return;
|
|
}
|
|
|
|
phy_ctl = tl_phy_readreg(sc, PHY_BMCR);
|
|
phy_sts = tl_phy_readreg(sc, TL_PHY_CTL);
|
|
|
|
if (phy_sts & PHY_CTL_AUISEL)
|
|
ifmr->ifm_active = IFM_ETHER|IFM_10_5;
|
|
|
|
if (phy_ctl & PHY_BMCR_LOOPBK)
|
|
ifmr->ifm_active = IFM_ETHER|IFM_LOOP;
|
|
|
|
if (phy_ctl & PHY_BMCR_SPEEDSEL)
|
|
ifmr->ifm_active = IFM_ETHER|IFM_100_TX;
|
|
else
|
|
ifmr->ifm_active = IFM_ETHER|IFM_10_T;
|
|
|
|
if (phy_ctl & PHY_BMCR_DUPLEX) {
|
|
ifmr->ifm_active |= IFM_FDX;
|
|
ifmr->ifm_active &= ~IFM_HDX;
|
|
} else {
|
|
ifmr->ifm_active &= ~IFM_FDX;
|
|
ifmr->ifm_active |= IFM_HDX;
|
|
}
|
|
|
|
return;
|
|
}
|
|
|
|
static int tl_ioctl(ifp, command, data)
|
|
struct ifnet *ifp;
|
|
u_long command;
|
|
caddr_t data;
|
|
{
|
|
struct tl_softc *sc = ifp->if_softc;
|
|
struct ifreq *ifr = (struct ifreq *) data;
|
|
int s, error = 0;
|
|
|
|
s = splimp();
|
|
|
|
switch(command) {
|
|
case SIOCSIFADDR:
|
|
case SIOCGIFADDR:
|
|
case SIOCSIFMTU:
|
|
error = ether_ioctl(ifp, command, data);
|
|
break;
|
|
case SIOCSIFFLAGS:
|
|
if (ifp->if_flags & IFF_UP) {
|
|
tl_init(sc);
|
|
} else {
|
|
if (ifp->if_flags & IFF_RUNNING) {
|
|
tl_stop(sc);
|
|
}
|
|
}
|
|
error = 0;
|
|
break;
|
|
case SIOCADDMULTI:
|
|
case SIOCDELMULTI:
|
|
tl_setmulti(sc);
|
|
error = 0;
|
|
break;
|
|
case SIOCSIFMEDIA:
|
|
case SIOCGIFMEDIA:
|
|
error = ifmedia_ioctl(ifp, ifr, &sc->ifmedia, command);
|
|
break;
|
|
default:
|
|
error = EINVAL;
|
|
break;
|
|
}
|
|
|
|
(void)splx(s);
|
|
|
|
return(error);
|
|
}
|
|
|
|
static void tl_watchdog(ifp)
|
|
struct ifnet *ifp;
|
|
{
|
|
struct tl_softc *sc;
|
|
u_int16_t bmsr;
|
|
|
|
sc = ifp->if_softc;
|
|
|
|
if (sc->tl_autoneg) {
|
|
tl_autoneg(sc, TL_FLAG_DELAYTIMEO, 1);
|
|
return;
|
|
}
|
|
|
|
/* Check that we're still connected. */
|
|
tl_phy_readreg(sc, PHY_BMSR);
|
|
bmsr = tl_phy_readreg(sc, PHY_BMSR);
|
|
if (!(bmsr & PHY_BMSR_LINKSTAT)) {
|
|
printf("tl%d: no carrier\n", sc->tl_unit);
|
|
tl_autoneg(sc, TL_FLAG_SCHEDDELAY, 1);
|
|
} else
|
|
printf("tl%d: device timeout\n", sc->tl_unit);
|
|
|
|
ifp->if_oerrors++;
|
|
|
|
tl_init(sc);
|
|
|
|
return;
|
|
}
|
|
|
|
/*
|
|
* Stop the adapter and free any mbufs allocated to the
|
|
* RX and TX lists.
|
|
*/
|
|
static void tl_stop(sc)
|
|
struct tl_softc *sc;
|
|
{
|
|
register int i;
|
|
struct ifnet *ifp;
|
|
|
|
ifp = &sc->arpcom.ac_if;
|
|
|
|
/* Stop the stats updater. */
|
|
untimeout(tl_stats_update, sc, sc->tl_stat_ch);
|
|
|
|
/* Stop the transmitter */
|
|
CMD_CLR(sc, TL_CMD_RT);
|
|
CMD_SET(sc, TL_CMD_STOP);
|
|
CSR_WRITE_4(sc, TL_CH_PARM, 0);
|
|
|
|
/* Stop the receiver */
|
|
CMD_SET(sc, TL_CMD_RT);
|
|
CMD_SET(sc, TL_CMD_STOP);
|
|
CSR_WRITE_4(sc, TL_CH_PARM, 0);
|
|
|
|
/*
|
|
* Disable host interrupts.
|
|
*/
|
|
CMD_SET(sc, TL_CMD_INTSOFF);
|
|
|
|
/*
|
|
* Disable MII interrupts.
|
|
*/
|
|
tl_dio_clrbit(sc, TL_NETSIO, TL_SIO_MINTEN);
|
|
|
|
/*
|
|
* Clear list pointer.
|
|
*/
|
|
CSR_WRITE_4(sc, TL_CH_PARM, 0);
|
|
|
|
/*
|
|
* Free the RX lists.
|
|
*/
|
|
for (i = 0; i < TL_RX_LIST_CNT; i++) {
|
|
if (sc->tl_cdata.tl_rx_chain[i].tl_mbuf != NULL) {
|
|
m_freem(sc->tl_cdata.tl_rx_chain[i].tl_mbuf);
|
|
sc->tl_cdata.tl_rx_chain[i].tl_mbuf = NULL;
|
|
}
|
|
}
|
|
bzero((char *)&sc->tl_ldata->tl_rx_list,
|
|
sizeof(sc->tl_ldata->tl_rx_list));
|
|
|
|
/*
|
|
* Free the TX list buffers.
|
|
*/
|
|
for (i = 0; i < TL_TX_LIST_CNT; i++) {
|
|
if (sc->tl_cdata.tl_tx_chain[i].tl_mbuf != NULL) {
|
|
m_freem(sc->tl_cdata.tl_tx_chain[i].tl_mbuf);
|
|
sc->tl_cdata.tl_tx_chain[i].tl_mbuf = NULL;
|
|
}
|
|
}
|
|
bzero((char *)&sc->tl_ldata->tl_tx_list,
|
|
sizeof(sc->tl_ldata->tl_tx_list));
|
|
|
|
ifp->if_flags &= ~(IFF_RUNNING | IFF_OACTIVE);
|
|
|
|
return;
|
|
}
|
|
|
|
/*
|
|
* Stop all chip I/O so that the kernel's probe routines don't
|
|
* get confused by errant DMAs when rebooting.
|
|
*/
|
|
static void tl_shutdown(dev)
|
|
device_t dev;
|
|
{
|
|
struct tl_softc *sc;
|
|
|
|
sc = device_get_softc(dev);
|
|
|
|
tl_stop(sc);
|
|
|
|
return;
|
|
}
|